Smartec STC-IPM3097A/1 User manual

3.0 Megapixel
Day & Night Box IP Camera
STC-IPM3097A/1
Thanks for purchasing our product. Before operating the unit, please read the
instructions carefully and keep this manual for future reference.

120110-XE3423NEO-0475-V2.0-V1a
i
Safety Warning
1. Read this manual carefully before installing the unit
Please read this manual first for correct installation and operation.
2. Never install the camera on a ceiling that cannot hold its weight
The product may fall down and cause damages.
3. Never install the camera near electric or magnetic fields
Install the camera away from TV, radio transmitter, magnet, electric motor, transformer, audio
speakers since the magnetic fields generate from above devices would distort the video image.
4. Never install or use the camera in areas exposed to water, oil or gas
The water, oil or gas may result in operation failure, electric shock or fire. Do not use this unit
near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet
basement, near a swimming pool, in an unprotected outdoor installation, or any area which is
classified as a wet location.
5. Never face the camera toward the sun
Direct sunlight or severe ray may cause fatal damage to sensor and internal circuit.
6. Power Cord Protection
Touching the wet power cord with hands or touching the power cord with wet hands may result in
electric shock. Power supply cords should be routed so that they are not likely to be walked on
or pinched by items placed upon or against them, playing particular attention to cords and plugs,
convenience receptacles, and the point where they exit from the appliance.
7. Attachments
Do not use attachment not recommended by the product manufacturer as they may cause
hazards.
8. Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous
voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of
any kind onto the product.
9. Do not operate the camera in environments where the temperature,
humidity or power source is beyond the specified ones
Use the camera in suitable environments where the temperature is within -10°C~50°C and
humidity below 80%. Use the input power source as this instruction indicated.

120110-XE3423NEO-0475-V2.0-V1a
ii
10. Cleaning
Unplug the unit from the outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning.
11. Never disassemble the camera nor put impurities in it
Disassembly or impurities may result in trouble or fire.
12. Stop using when the product emits smoke or abnormal heat
13. Servicing
Do not attempt to repair this unit yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
14. Retain Instructions
THE SAFETY AND OPERATING INSTRUCTIONS SHOULD BE RETAINED FOR FUTURE
REFERENCE.
NOTE:
The information in this manual was current when published. The manufacturer reserves the right to
revise and improve its products. All specifications are therefore subject to change without notice.

120110-XE3423NEO-0475-V2.0-V1a
iii
Table of Contents
1. CAMERA................................................................................................................................................................................ 1
1.1 FEATURE........................................................................................................................................................................... 1
1.2 LIST OF CONTENTS ............................................................................................................................................................ 1
1.3 SYSTEM REQUIREMENTS.................................................................................................................................................... 1
1.4 SPECIFICATION .................................................................................................................................................................. 2
1.5 DIMENSIONS...................................................................................................................................................................... 3
1.6 CAMERA OVERVIEW........................................................................................................................................................... 4
1.7 INSTALLATION .................................................................................................................................................................... 6
2. DIRECT LINK (CASE 1) ......................................................................................................................................................... 7
3. LINK OVER HUB /POEHUB (CASE 2) ................................................................................................................................... 7
2. USER INTERFACE ................................................................................................................................................................ 8
2.1 LOGIN ............................................................................................................................................................................... 8
2.2 INTERFACE OVERVIEW ....................................................................................................................................................... 9
1. Live View ............................................................................................................................................................. 10
2. Video ....................................................................................................................................................................11
3. Image .................................................................................................................................................................. 13
4. Audio ................................................................................................................................................................... 15
5. DateTime............................................................................................................................................................. 16
6. Network ............................................................................................................................................................... 17
7. Alarm................................................................................................................................................................... 18
8. Storage................................................................................................................................................................ 19
9. Maintain............................................................................................................................................................... 20
10. PTZ/OSD............................................................................................................................................................. 21

120110-XE3423NEO-0475-V2.0-V1a
1
1. CAMERA
1.1 Feature
Sony 1/2.8” EXmor™ 3.0 MP Progressive CMOS Sensor
Super Low Lux, Color:[email protected], B/W:0.01[email protected] Sense Up:[email protected]
Compression: H.264, MPEG-4, M-JPEG (Triple-code Encoder)
Highest Resolution: 2048x1536@20fps, H.264/High-Profile
Bit Rate Transmission up to 16,000 Kbps
Support DC12V&PoE (802.3af) Power Input
Support Micro SD/SDHC Card (Up to 16GB)
For Low Power Consumption Design, Less than 4W
Support Both ONVIF and PSIA
1.2 List of Contents
CD *1
Audio and video cable (YPbPr signal) *1
User manual
Accessories
‧CS ring
‧Hex wrench
‧LENS terminal
1.3 System Requirements
For IE Browser Live View--
Resolution
1280x720p
1280x1024p
1920x1080p
2056x1536p(3.0MP)
Suggested Bitrate
2000~4000kbps
2000~6000kbps
4000~8000kbps
4000~10000kbps
Compression format
H264 or MPEG4
H264 or MPEG4
H264 or MPEG4
H264 or MPEG4
Frame Rate
Up to 30fps
Up to 30fps
Up to 30fps
Up to 20fps
CPU (Recommended)
Intel Core i3 540
Intel Core i3 540
Intel Core i5 760
Intel Core i7 860
RAM
2GB RAM
2GB RAM
4GB RAM
4GB RAM
IE Browser
8.0 or above
8.0 or above
8.0 or above
8.0 or above
OS
WinXP-Pro
WinXP-Pro
WinXP-Pro/Win7 Pro
WinXP-Pro/Win7 Pro
Microsoft Internet Explorer 8.0 or above(Only support 32bit IE Browser)
The compression format of IP Cam encoder is in H.264/High profile.
When using Live view in IE Browser, IP Cam will decode in real time by RTSP, the maximum
bitrate is 10,000kps.

120110-XE3423NEO-0475-V2.0-V1a
2
1.4 Specification
VIDEO
Image Sensor
Sony 1 / 2.8" 3.0 Megapixel Progressive Exmor™ CMOS
Highest Resolution
QXGA (2048x1536)
Video Resolution
2048x1536, 1920x1080, 1280x1024, 1280x960, 1280x720, 720x480
Video Frame Rate
2048x1536@20fps, others up to 30fps
Video Compression
H.264, MPEG4, M-JPEG
Video Frame Rate
2048x1536(20fps) , Other resolutions (H264 or MPEG4) Up to 30 fps for All
Video Profile
Minimum Illumination
Color:[email protected], B/W:0.01Lux@F1.2, Sense Up:0.001Lux@F1.2
Digital Wide Dynamic
Range
10 Level (Adjustable Level Settings)
Second Video Output
1.0Vp-p Composite, 75Ω (BNC) or YPbPr
FUNCTION
Menu
Can Be Set via Browser
Digital Day&Night Mode
Auto / Color / Black&White
Auto Electronic Shutter
Auto:1/60 to 1/2,000 sec. (60Hz) ; 1/50 to 1/2,000 sec. (50Hz)
Manual Electronic
Shutter
1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/120, 1/250, 1/500, 1/750, 1/1000, 1/1500,
1/2000 sec.
White Balance
Auto / Manual (1800°K~10,000°K)
Dynamic Noise
Reduction
2D DNR
Language
Traditional Chinese / Simplified Chinese / English / Japanese
Image Setting
Brightness / Contrast / AWB / Sharpness / Saturation / Rotation / Mirror/
WDR
Motion Detection
Yes
Motion Alarm Trigger
Yes
Timer Clock
Yes
NETWORK
Browser
IE 8.0 or Above
Ethernet
10/100M Auto Negotiation
Bit Rate Transmission
64 up to 16,000 Kbps
Supported Protocols
TCP, UDP, HTTP, SMTP, FTP, NTP, DNS, DHCP, ARP, UPnP, RTSP RTP
Ethernet (RJ-45 Wired 10/100 Base-TX)
Video Streaming
H.264, MPEG4 and M-JPEG Dual/Triple Streaming
Audio Streaming ;
Compression
Two-way Audio ; G.711 (μLaw), 8KHz Sample Rate
Users
Support 10 Simultaneous Users
Security
ID/Password Protection, IP Address Filtering, User Access Log
Alarm Event
File Upload via FTP and E-mail/Notification via E-mail, HTTP, External Digital
Output Activation, Micro SD Recording
Multicast
Support Multicast
GENERAL
Connector
YPbPr/Audio, RJ45/PoE, DC Power Jack, BNC (Composite Video Out),
Alarm Reset/Alarm In/Alarm Out/Alarm Ground/RS485, Micro SD/SDHC,
Mini USB
Automatic IRIS ;
Connector
DC; D4 IRIS Jack
Lens Mount
CS / C Mount (With Adaptor Ring)
Power Supply ;
Consumption
12Vdc / PoE ; 4W
Operation ; Storage
Temp.
-10°C ~ 50°C ; -20°C ~ 60°C
Operation ; Storage
Humidity
Maximum: RH80% ; RH90%
Dimensions
60(W)x50(H)x119(D)mm
Net Weight
350g

120110-XE3423NEO-0475-V2.0-V1a
3
1.5 Dimensions
(Size in mm)
IRIS

120110-XE3423NEO-0475-V2.0-V1a
4
1.6 Camera Overview
1. Side View (Auto IRIS)
Auto IRIS Pin
(1) CON-
(2) CON+
(3) DR+
(4) DR-
2. Mount Adaptor
①Mount Adaptor
②Mount adaptor can be attached to the top of the camera (for hanging)
③Mount adaptor can be attached to the bottom of the camera (for bracket)
④Mount adaptor screw size: M2.6x0.45P
3. Front View
①Light Sensor
②Microphone

120110-XE3423NEO-0475-V2.0-V1a
5
4. Rear View
■Function Switch:
(1) STATIC IP: Fixed IP (2) DHCP: DHCP Floating IP
(3) DC IRIS: Auto IRIS (DC Driver Lens) (4) AES: Fixed Lens
■Power / LAN LED:
(1) Power LED: Green—Normal Orange—Abnormal
(2) LAN LED: Green—Successfully Connected Red—Connecting Orange—Error
■DI / DO Port:
(1) ALM-RST (Alarm Reset): The system will force the alarm input to cancel.
(2) ALM-IN (Alarm Input):When activate, the alarm will be triggered. (You may also set the
input controlled by DAY/NIGHT program.)
(3) ALM-OUT (Alarm Output):Triggered when the alarm outputted (TTL Level). (You may also
set the alarm to output while the DAY/NIGHT Mode is activated.)
(4) GND (Ground)
(5) RS-485(－) Output: Controlled by RS-485 signal sent by the network part (NEGATIVE).
(6) RS-485(＋) Input: Controlled by RS-485 signal sent by the network part. (POSTIVE)
■RESET:
Press reset key with small screw driver, hold for a few seconds, and re-connect the power, the
camera will automatically start to reset in 5 seconds. After reset, all the settings will restored to
the default. The default IP is 192.168.1.168. After reset, IP will be restored to the default.
■DC 12V:
DC Jackψ2.1, DC12V---0.5A or higher.
■YPbPr/Audio:
For connecting with audio/video cable. Green: Y / Blue: Pb / Red: Pr / White: Audio
LAN / PoE
(RJ-45)
Power 12V DC
Micro SD /
SDHC
Mini USB
DI / DO
Audio/Video Out
Function Switch
Reset Switch
Video Out
(BNC)
Power / LAN
LED

120110-XE3423NEO-0475-V2.0-V1a
6
1.7 Installation
1. Installation Flow Chart
Default Settings of IP CAM
IP Address: 192.168.1.168
User Name: admin
Password: 9999
Suggested IP Address For PC/NB
IP Address: 192.168.1.200
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.1
START
Power
Type
FINISH
DC
Check the power of PoE
Plug the Power Adapter
Connect the RJ-45 LAN cable to the IP
CAM
Get into the IP CAM setting window
PoE
IP setting for PC/NB
(Please see the suggested IP address)
Disable the anti-virus software and firewall
Turn on the PC/NB and log-in Windows
OS
Run IE browser (IE 8.0 or above)
User Name: admin Password: 9999
Type the URL http://192.168.1.168
and get into IP CAM setting window

120110-XE3423NEO-0475-V2.0-V1a
7
2. Direct Link (Case 1)
(1) Plug the power adapter to IP CAM.
(2) Run the IE browser with http://192.168.1.168
(3) When the log-in window pop-up, please input the User Name and Password.
(4) Whenever the connection is ready, the main page (setting window) of IP CAM will show on.
3. Link Over Hub / PoE Hub (Case 2)
(1) Run the IE browser with http://192.168.1.168
(2) When the log-in window pop-up, please input the User Name and Password.
(3) Whenever the connection is ready, the main page (setting window) of IP CAM will show on.
Adapter
DC12V
Cat-5 LAN cable
PoE / Hub
Cat-5 LAN cable
Cat-5 LAN cable

120110-XE3423NEO-0475-V2.0-V1a
8
2. USER INTERFACE
2.1 Login
1. Start the browser, and input http://192.168.1.168/ in the address field, then press Enter.
(PS: The shown screen is in Microsoft Windows 7 English platform.)
2. Enter User Name and Password In the prompt window, and click OK.
The default User Name and Password is admin and 9999. You will need to enter the account and password
every time whenever you restart the application or reconnect.

120110-XE3423NEO-0475-V2.0-V1a
9
2.2 Interface Overview
After login to the system, the screen will be displayed as below:
There are many function buttons on the left side. They are as the table below. All of the function buttons
and its details will be shown on the following sections.
Live View
Video
Image
Audio
DateTime
Network
Alarm
Storage
Maintain
PTZ/OSD

120110-XE3423NEO-0475-V2.0-V1a
10
1. Live View
Main page. Display the image captured by the camera.
Language:
English / 日本語(Japanese) / 繁中(Traditional Chinese) /
簡中(Simplified Chinese)
Full Screen
Snapshot
Folders
Information
Web View
Upload
Audio On
Audio Off

120110-XE3423NEO-0475-V2.0-V1a
11
2. Video
IP (Internet Protocol) video settings of the camera. Modify the settings of IP stream type,
streams and local display.
NOTE:
Once the change completed, click Submit to save the settings.
Stream Type
Video Streams
Single / Dual / Tri-stream
Codec Profiles
H.264 + MPEG4 + MegaPixel JPEG
Resolution
H.264: 720P, H.264: D1, H.264: SXGA, H.264:1080P, H.264:
3M
(NOTE: The content may vary by models)

120110-XE3423NEO-0475-V2.0-V1a
12
H.264
Frame rate
1 / 3 / 5 / 10 / 15 / 20 / 25 / 30 fps
Bitrate
4000 Kbps
Rate Control
OFF / VBR / CBR
Local Display
Local Display
OFF / NTSC / PAL / HD720P
Rotation
OFF / HORIZONTAL / VERTICAL / BOTH
Format
H.264 (1920 x 1080)
Size
5 sec / 10 sec
Shutter Speed (Min)(Second)
1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/120, 1/250, 1/500, 1/750,
1/1000, 1/1500, 1/2000, 1/10000, 1/100000
Shutter Speed (Max)(Second)
1/30, 1/60, 1/120, 1/250, 1/500, 1/750, 1/1000, 1/1500,
1/2000, 1/10000, 1/100000
Shutter Speed (Level)
0~7
Quality (Level)
0~7
FixedShutter (Second)
1/2, 1/4, 1/8, 1/15, 1/30, 1/60, 1/120, 1/250, 1/500, 1/750,
1/1000, 1/1500, 1/2000, 1/10000, 1/100000
FixedShutter (Level)
0~7
(NOTE: The content may vary by models)

120110-XE3423NEO-0475-V2.0-V1a
13
3. Image
Modify the settings of image, OSD and advanced image settings.
Image
Brightness
0 ~ 255 (Default 128)
Contrast
0 ~ 255 (Default 128)
Saturation
0 ~ 255 (Default 128)
Sharpness
0 ~ 255 (Default 128)
DeNoise
0 ~ 255 (Default 128)
EV Compensation
0 ~ 255 (Default 128)
Load Default
Restore to the default values
Stream1 / Stream2 / Stream3 OSD
Mode
Date / Time / Text
Text Position
Top-Left / Top-Right

120110-XE3423NEO-0475-V2.0-V1a
14
Advanced Settings
Auto IRIS
Manual / Auto
Flicker Control
60hz NTSC / 50hz PAL
White Balance
AUTO_WIDE / AUTO_NORMAL / SUNNY / SHADOW /
INDOOR / LAMP / FL1 / FL2
Back Light Compensation
Off / On
Back Light Level
Min / Mid / Max
WDR Enhancement
Off / On
WDR Level
0~7
IR-Cut Setting
Auto / BW / Color / External
(NOTE: The content may vary by models)

120110-XE3423NEO-0475-V2.0-V1a
15
4. Audio
Modify the settings of audio.
Audio
Enable Audio
Enable / Disable
Audio Mode
MIC / SPEAKER / BOTH
Input volume
0~100
Sample Rate
8KHz / 16KHz
Bitrate
Auto / 64Kbps
Output Volume
0~100
(NOTE: The content may vary by models)

120110-XE3423NEO-0475-V2.0-V1a
16
5. DateTime
Modify the settings of date and time.
DateTime
Set Manual Date
Manual set the date and time
Sync Current PC Date
Synchronization the date and time with current PC
Sync with SNTP Server
Synchronization the date and time with SNTP Server
Date Format / Position
Select the format and position of date
Time Format / Position
Select the format and position of time