Smarteh LPC-2.DI5 User manual

USER MANUAL
Longo programmable controller
LPC-2.DI5
Digital Input module
Version 6
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: [phone] / e-mail: in[email protected] / www.smarteh.si

Longo programmable controller LPC-2.DI5
Written by SMAR EH d.o.o.
Copyright © 2016, SMAR EH d.o.o.
User Manual
Document Version: 6
April, 2016
i

Longo programmable controller LPC-2.DI5
S ANDARDS AND PROVISIONS: Standards, recommendations, regulations
and provisions of the country in which the devices will operate, must
be considered while planning and setting up electrical devices. Work
on 100 .. 240 V AC network is allowed for authorized personnel only.
DANGER WARNINGS: Devices or modules must be protected from
moisture, dirt and damage during transport, storing and operation.
WARRAN Y CONDI IONS: For all modules LONGO LPC-2 – if no
modifications are performed upon and are correctly connected by
authorized personnel – in consideration of maximum allowed
connecting power, warranty of 24 months is valid from the date of sale
to the end buyer, but not more than 36 months after delivery from
Smarteh. In case of claims within warranty time, which are based on
material malfunctions the producer offers free replacement. he
method of return of malfunctioned module, together with description,
can be arranged with our authorized representative. Warranty does
not include damage due to transport or because of unconsidered
corresponding regulations of the country, where the module is
installed.
his device must be connected properly by the provided connection
scheme in this manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous voltage in the device can cause electric shock and may
result in personal injury or death.
NEVER SERVICE HIS PRODUC YOURSELF!
his device must not be installed in the systems critical for life (e.g.
medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer,
the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected
separately!
LONGO LPC-2 complies to the following standards:
•EMC: EN 61000-6-3:2007 + A1:2011, EN 61000-6-1:2007, EN 61000-
3-2:2006 + A1:2009 + A2: 2009, EN 61000-3-3:2013
•LVD: IEC 61010-1:2010 (3rd Ed.), IEC 61010-2-201:2013 (1st Ed.)
Smarteh d.o.o. operates a policy of continuous development.
herefore we reserve the right to make changes and improvements to
any of the products described in this manual without any prior notice.
MANUFAC URER:
SMAR EH d.o.o.
Poljubinj 114
5220 olmin
Slovenia
ii

Longo programmable controller LPC-2.DI5
Longo programmable controller LPC-2.D 5
1 DESCRIP ION...................................................................................1
2 FEA URES.......................................................................................2
3 INS ALLA ION..................................................................................3
3.1 Connection scheme....................................................................3
3.2 Mounting instructions.................................................................5
3.3 Module labeling........................................................................6
3.4 echnical specifications...............................................................7
4 CHANGES .......................................................................................8
5 NO ES...........................................................................................9
iii

Longo programmable controller LPC-2.DI5
1 DESCR PT ON
LPC-2.DI5 is intended for use as digital input module for voltage free (dry) contacts. Eight channels
are available for input connection. Module's inputs are galvanic isolated. Module can be used in a
wide range of operation.
LEDs indicate state of contact on correspondent input (refer to the able 6).
Module is powered from internal BUS.
NO E: For proper system configuration and data allocation please refer to LPC Composer software
help menu.
1

Longo programmable controller LPC-2.DI5
2 FEATURES
Figure 1: LPC-2.DI5 module.
Table 1: Technical data
Eight standard digital inputs, galvanic isolated
Flexible input for wide use of operation
Standard DIN EN50022-35 rail mounting
2

Longo programmable controller LPC-2.DI5
3 NSTALLAT ON
3.1 Connection scheme
Figure 2: Connection scheme
Table 2: N1
IN1.1 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN1.2 (+U)224 V DC / 10 mA output Power supply output
IN2.3 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN2.4 (+U)224 V DC / 10 mA output Power supply output
IN3.5 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN3.6 (+U)224 V DC / 10 mA output Power supply output
1 Wires connected to the module must have cross sectional area at least 0.75 mm2. Minimum temperature rating of wire
insulation must be 85 °C.
2 Pins IN1.2, IN2.4, IN3.6, IN4.8, IN5.10, IN6.12, IN7.14 and IN8.16 are always on the same potencial.
3
K2K1
LED1 - LED4
LED5 - LED8

Longo programmable controller LPC-2.DI5
Table 2: N
IN4.7 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN4.8 (+U)324 V DC / 10 mA output Power supply output
IN5.9 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN5.10 (+U)324 V DC / 10 mA output Power supply output
IN6.11 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN6.12 (+U)324 V DC / 10 mA output Power supply output
IN7.13 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN7.14 (+U)324 V DC / 10 mA output Power supply output
IN8.15 (I) Digital input, 0 .. 24 V DC 24 V DC digital input
IN8.16 (+U)324 V DC / 10 mA output Power supply output
Table 3: Digital input specification
IN1.1 .. IN8.15
“Off” (RSW < 5 kΩ)
“On” (RSW > 40 kΩ)
Max. input frequency = 5 Hz
Voltage free (dry) contact input
Table 4: K1
Internal BUS Data & DC power supply Connection to I/O module
Table 5: K2
Internal BUS Data & DC power supply Connection to I/O module
Table 6: LED1 – LED8
Status Digital input state
On: IN1.1 connected to IN1.2 up to IN8.15 connected to
IN8.16 (contact closed)
Off: IN1.1 not connected to IN1.2 up to IN8.15 not
connected to IN8.16 (contact opened)
3 Pins IN1.2, IN2.4, IN3.6, IN4.8, IN5.10, IN6.12, IN7.14 and IN8.16 are always on the same potencial.
4

Longo programmable controller LPC-2.DI5
3.2 Mounting instructions
Figure 3: Housing dimensions
Dimensions in milimeters
All connections, module attachments and assembling must be done
while module is not connected to the main power supply.
Mounting instructions:
1. Switch OFF main power supply.
2. Mount LPC-2.DI5 module to the provided place inside an electrical panel (DIN EN50022-35
rail mounting).
3. Mount other LPC-2 modules (if required). Mount each module to the DIN rail first, then
attach modules together through K1 and K2 connectors.
4. Connect digital inputs' wires according to the connection scheme in Figure 2.
5. Switch ON main power supply.
Dismount in reverse order. For mounting/dismounting modules to/from DIN rail a free space of at
least one module must be left on the DIN rail.
NO E: LPC-2 main module should be powered separately from other electrical appliance connected
to LPC-2 system. Signal wires must be installed separately from power and high voltage wires in
accordance with general industry electrical installation standard.
5
53
90
95
36
60

Longo programmable controller LPC-2.DI5
3.3 Module labeling
Figure 4: Labels on housing
Label 1: Label 2:
Label 1 description:
1. LPC-2.MC3 is the full product name.
2. P/N:225MC3040001001 is the part number.
•225 – general code for LPC-2 product family,
•MC3 – short product name,
•04001 – sequence code,
•04 – year of code opening,
•001 – derivation code,
•001 – version code (reserved for future HW and/or SW firmware upgrades).
3. D/C:16/05 is the date code.
•16 – week and
•05 – year of production.
Label 2 description:
1. S/N:MC3-S9-0500000190 is the serial number.
•MC3 – short product name,
•S9 – user code (test procedure, e.g. Smarteh person xxx),
•0500000190 – year and current stack code,
•05 – year (last two cyphers),
•00000190 – current stack number; previous module would have the stack number
00000189 and the next one 00000191.
6

Longo programmable controller LPC-2.DI5
3.4 Technical specifications
Table 6: Technical specifications
Power supply from internal BUS
Power consumption 1.5 W
Number of digital inputs 8
Input threshold ”ON”: <5 kΩ
“OFF”: >40 kΩ
Connection type screw type connector for stranded wire 0.75 to
2.5 mm2
Max. transition time 1 s
Dimensions (L x W x H) 90 x 53 x 60 mm
Weight 100 g
Ambient temperature 0 to 50 °C
Ambient humidity max. 95 %, no condensation
Maximum altitude 2000 m
Mounting position vertical
ransport and storage temperature -20 to 60 °C
Pollution degree 2
Protection class IP 30
7

Longo programmable controller LPC-2.DI5
4 CHANGES
he following table describes all the changes to the document.
Date V. Description
13.04.16 6 General update.
01.07.12 5 CGP General update .
11.05.10 4 Updated warranty permanence.
30.06.05 3 he initial version, issued as LPC-2.DI5 module UserManual.
8

Longo programmable controller LPC-2.DI5
5 NOTES
9