Smarteh LONGO LPC-2.CR2 User manual

USER MANUAL
Longo programmable controller
LPC-2.CR2
Card Reader module
Version 4
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: [phone] / e-mail: [e-mail] / www.smarteh.si

Longo programmable controller LPC-2.CR2
Written by SMARTEH d.o.o.
Copyrig t © 2016, SMARTEH d.o.o.
User Manual
Document Version: 004
June, 2016
i

Longo programmable controller LPC-2.CR2
STANDARDS AND PROVISIONS: Standards, recommendations,
regulations and provisions of t e country in w ic t e devices will
operate, must be considered w ile planning and setting up electrical
devices. Work on 100 .. 240 V AC network is allowed for aut orized
personnel only.
DANGER WARNINGS: Devices or modules must be protected from
moisture, dirt and damage during transport, storing and operation.
WARRANTY CONDITIONS: For all modules LONGO LPC-2 – if no
modifications are performed upon and are correctly connected by
aut orized personnel – in consideration of maximum allowed
connecting power, warranty of 24 mont s is valid from t e date of
sale to t e end buyer, but not more t an 36 mont s after delivery
from Smarte . In case of claims wit in warranty time, w ic are based
on material malfunctions t e producer offers free replacement. T e
met od of return of malfunctioned module, toget er wit description,
can be arranged wit our aut orized representative. Warranty does
not include damage due to transport or because of unconsidered
corresponding regulations of t e country, w ere t e module is
installed.
T is device must be connected properly by t e provided connection
sc eme in t is manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous voltage in t e device can cause electric s ock and may
result in personal injury or deat .
NEVER SERVICE THIS PRODUCT YOURSELF!
T is device must not be installed in t e systems critical for life (e.g.
medical devices, aircrafts, etc.).
If t e device is used in a manner not specified by t e manufacturer,
t e degree of protection provided by t e equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected
separately!
LONGO LPC-2 complies to t e following standards:
•EMC: EN 61000-6-3:2007 + A1:2011, EN 61000-6-1:2007, EN 61000-
3-2:2006 + A1:2009 + A2: 2009, EN 61000-3-3:2013
•LVD: IEC 61010-1:2010 (3rd Ed.), IEC 61010-2-201:2013 (1st Ed.)
Smarte d.o.o. operates a policy of continuous development.
T erefore we reserve t e rig t to make c anges and improvements to
any of t e products described in t is manual wit out any prior notice.
MANUFACTURER:
SMARTEH d.o.o.
Poljubinj 114
5220 Tolmin
Slovenia
ii

Longo programmable controller LPC-2.CR2
Longo programmable controller LPC-2.CR2
1 ABBREVIATIONS................................................................................1
2 DESCRIPTION...................................................................................2
3 FEATURES.......................................................................................3
4 OPERATION.....................................................................................4
4.1 Parameters..............................................................................4
5 INSTALLATION..................................................................................5
5.1 Connection sc eme....................................................................5
5.2 Mounting instructions.................................................................7
5.3 Module labeling........................................................................8
6 TECHNICAL SPECIFICATIONS.................................................................9
7 SPARE PARTS..................................................................................10
8 CHANGES .....................................................................................11
9 NOTES..........................................................................................12
iii

Longo programmable controller LPC-2.CR2
1 A REVIATIONS
Sorted by order of appeareance in document:
RFID Radio frequency identification
SOS Emergency call
LED Lig t emitting diode
DIP Dual in-line package
ID Identity
1

Longo programmable controller LPC-2.CR2
2 DESCRIPTION
LPC-2.CR2 RFID reader is intended to be used as an identity verification device for outdoor
mounting.
W en RFID tag (key-card) is approac ed to t e reader and its code is successfully read out, t e
green LED blinks and a s ort beep is generated. In case key-card for correspondent room is valid, t e
green LED blinks again and a s ort beep is generated. Ot er devices can be activated at t is event
like door lock opening, turning lig t on... If key-card number is not valid, t e red LED blinks and a
longer beep is generated.
Functionalities are controlled from main module. Controller is accompanied wit Smarte IDE
application. It is a tool, w ere various modules can be put toget er to a configuration, based on
number and type of electrical signals needed. Smarte IDE takes care for proper modules position.
Latest Smarte IDE setup can be downloaded from Smarte web page support section:
www.smarte .si/Support/Downloads/Software/Development_tools
LPC-2.CR2 module can be modified on customer request: custom front label, pus buttons added,
LEDs added. For more information please contact manufacturer.
2

Longo programmable controller LPC-2.CR2
3 FEATURES
Figure 1: LPC-2.CR2 module.
Table 1: Technical data
RFID reader
OK “ √ ” LED
Fault “ X ” LED
Power LED
Internal fault LED
Internal built-in buzzer
IP65 ousing for outdoor mounting
Black or w ite glass possibility
3

Longo programmable controller LPC-2.CR2
4 OPERATION
Operation of t e CR2 module is also dependent on parameters received on RS-485 communication
c annel.
Reader RFID field is active always w en module is powered up. If tag is put inside RFID field, reader
tries to resolve RFID tag code. If code is read successfully, module activates status iIDNew,
generates a s ort beep, OK LED1 blinks and code is transmitted in iIDW1 - iIDW3 status fields. In
main module application t is code can be read out and aut enticated. If code as appropriate
rig ts, main module s ould activate oOK command. If code is not aut orized, main module
application s ould activate oFault command. Regarding command received, following action are
triggered on module:
oOK --> OK LED2 blink, s ort beep.
oFault --> Fault LED1 blink, long beep.
Eit er command is received or no command is received wit in 10 sec, module clears iIDNew status
and waits for next RFID tag. W ile CR2 module is waiting for aut orization response, new RFID tags
can not be read.
4.1 Parameters
If parameter is set to logical “1”, is considered to be active, enabled or set. If parameter as
logical value “0” is considered to be inactive, disabled, or cleared.
Parameter can be feedback or command. Parameter as feedback means t at CR2 module is sending
information to main module. On t e ot er and, command represents request from main module to
module.
Command:
ID Fault [oFault]: Command for rejecting aut orization of RFID code.
ID OK [oOk]: Command for aut orization of RFID code.
uzzer [oBuzz]: W ile t is command is active, buzzer is active.
'Fault' ID LED [oFaultLD]: W ile t is command is active, fault LED1 is set.
'OK' ID LED [oOkLD]: W ile t is command is active, OK LED2 is set.
Card Type Selection [oSelTyp]: 0 Emarine; 1 itag.→ →
Feedback:
RFID ID receiv. Word1 (s) [iDW1]: Upper (most significant) t ird of RFID code.
RFID ID receiv. Word2 (s) [iDW2]: Middle t ird of RFID code.
RFID ID receiv. Word3 (s) [iDW3]: Lower (least significant) t ird of RFID code.
New ID [iIDNew]: W en new RFID tag is recognized, t is status is set active for 10sec or till
aut orization command is received (oOK or oFault).
Communication [iComm]: Normal state is “0”. If set, t ere is communication error or no
communication establis ed.
'Up-right' T [iUp TB]: signal from button located up-rig t corner (t is button is disabled
by default and can be enable in EPROM).
'Up-left' T [iUpLTB]: signal from button located up-left corner (t is button is disabled by
default and can be enable in EPROM).
4

Longo programmable controller LPC-2.CR2
5 INSTALLATION
5.1 Connection scheme
Figure 2: Connection scheme
5

Longo programmable controller LPC-2.CR2
Table 2: K1
K1.1 GND Ground
K1.2 10 .. 24 V DC Power supply input
K1.3 RS-485 A Data receive/send line A
K1.4 RS-485 B Data receive/send line B
Table 3: LEDs & uttons
LED1: red Fault “ X ” ON: RFID key standard NOK or ID card number wrong
OFF: No tag in proximity
LED2: green OK “ √ ”ON: RFID key standard OK and ID card number valid
OFF: No tag in proximity
LED5: red Communication ON: RS-485 communication fault
OFF: RS-485 communication OK
LED6: green Power supply ON: power supply OK
OFF: power supply missing or power off
Table 4: S1
RS-485 ADDRESS Switch 1 Switch 2
0 OFF OFF
1 OFF ON
2 ON OFF
3 ON ON
6

Longo programmable controller LPC-2.CR2
5.2 Mounting instructions
Figure 3: Housing dimensions
Dimensions in millimeters.
All connections, module attac ments and assembling must be done w ile
module is not connected to t e main power supply.
Several RFID panels s ould not be mounted close to eac ot er. Minimum
distance to next panel is at least 30 cm. T is restriction also applies in
case of mounting panels on bot sides of t e same wall. Adequate s ielding
material and provisions could be used to avoid interference between
panels.
RFID panel s ould not be positioned close to conductive areas.
1. Set t e correct RS-485 address (S1 switc ) for LPC-2.CR2 (refer to t e Table 4).
2. Drill a ole for cable inlet on desired side and position of t e module. Be aware to use
proper IP class inlet to insure t at module will still be resistant to desired level.
3. Connect interconnection cable to t e connector K1. Max. allowed tractive force is 30 N.
4. Mount LPC-2.CR2 module on provided
5. Cover LPC-2.CR2 wit cover plate
LPC-2.CR2 connects to t e main module unit on its RS-485 port using interconnection cable. W en
more special modules (e.g. LPC-2.CA1, LPC-2.CH1, LPC-2.DP1) are connected to main module,
splitter is also required (e.g. SPL-2). Signal wires must be installed separately from power and ig
voltage wires in accordance wit general industry electrical installation standard.
7

Longo programmable controller LPC-2.CR2
5.3 Module labeling
Table 5: Labels on housing
Label 1 (sample): Label 2 (sample):
Label 1 descriptions:
1. LPC-2.CR2 is t e full product name.
2. P/N: 225CR210V01001 is t e part number.
•225 – general code for product family,
•CR2 – s ort product name,
•10V01 – sequence code,
•10 – year of code opening,
•V - denotes flus frame mounting module,
•001 – derivation code,
•001 – version code (reserved for future HW and/or SW firmware upgrades).
3. D/C:01/10 is t e date code.
•01 – week and
•10 – year of production.
Label 2 descriptions:
1. S/N: CR-S9-1000000003 is t e serial number.
•CR2 – s ort product name,
•S9 – user code (test procedure, e.g. Smarte person xxx),
•1000000003 – year and current stack code,
•10 – year (last two cyp ers),
•00000003 – current stack number; previous module would ave t e stack number
00000002 and t e next one 00000004.
8
LPC-2.CR2
P/N:225CR210V01001
D/C: 01/10
S/N: CR2-S9-1000000003

Longo programmable controller LPC-2.CR2
6 TECHNICAL SPECIFICATIONS
Table 6: Technical specifications
Power supply from main module
Interconnection connector type RJ-12 6/6
Power consumption 1.5 W
RFID type EM4100, 125 kHz, Manc ester 64, read only
Max. reading distance 4 cm
Dimensions (W x H x D) 120 x 80 x 60 mm
Weig t 200 g
Ambient temperature 0 to 50 °C
Maximum altitude 2000 m
Mounting position any
Transport and storage temperature -20 to 60 °C
Protection class IP 65
9

Longo programmable controller LPC-2.CR2
7 SPARE PARTS
For ordering spare parts following Part Numbers s ould be used:
LPC-2.CR2 Card Reader module
LPC-2.CR2, EM, black P/N: 225CR210V01001
LPC-2.CR2 Card Reader module
LPC-2.CR2, EM, w ite P/N: 225CR216V03W03
LPC-2.MC8 Main module
LPC-2.MC8 P/N: 225MC813001001
Splitter
SPL-2 (1/8) P/N: 206SPL04002001
Interconnection cable
ICM-x P/N: 203ICMxxxxxxxx
10

Longo programmable controller LPC-2.CR2
8 CHANGES
T e following table describes all t e c anges to t e document.
Date V. Description
07.06.2016 4 General update.
01.06.2014 3 Power consumption data update.
01.07.2012 2 CGP General update.
18.03.2010 1 T e initial version, issued as LPC-2.CR2 module UserManual.
11

Longo programmable controller LPC-2.CR2
9 NOTES
12