Smarteh LPC-2.DD4 User manual

USER MANUAL
Longo programmable controller
LPC-2.DD4
4 Channel Dimmer module
Version 1
SMARTEH d.o.o. / Poljubinj 114 / 5220 Tolmin / Slovenia / Tel.: [phone] / e-mail: [e-mail] / www.smarteh.si

Longo programmable controller LPC-2.DD4
Written by SMAR EH d.o.o.
Copyright © 2019, SMAR EH d.o.o.
User Manual
Document Version: 1
July, 2019
i

Longo programmable controller LPC-2.DD4
S ANDARDS AND PROVISIONS: Standards, recommendations,
regulations and provisions of the country in which the devices will
operate, must be considered while planning and setting up electrical
devices. Work on 100 .. 240 V AC network is allowed for authorized
personnel only.
DANGER WARNINGS: Devices or modules must be protected from
moisture, dirt and damage during transport, storing and operation.
WARRAN Y CONDI IONS: For all modules LONGO LPC-2 – if no
modifications are performed upon and are correctly connected by
authorized personnel – in consideration of maximum allowed
connecting power, warranty of 24 months is valid from the date of
sale to the end buyer, but not more than 36 months after delivery
from Smarteh. In case of claims within warranty time, which are based
on material malfunctions the producer offers free replacement. he
method of return of malfunctioned module, together with description,
can be arranged with our authorized representative. Warranty does
not include damage due to transport or because of unconsidered
corresponding regulations of the country, where the module is
installed.
his device must be connected properly by the provided connection
scheme in this manual. Misconnections may result in device damage,
fire or personal injury.
Hazardous voltage in the device can cause electric shock and may
result in personal injury or death.
NEVER SERVICE HIS PRODUC YOURSELF!
his device must not be installed in the systems critical for life (e.g.
medical devices, aircrafts, etc.).
If the device is used in a manner not specified by the manufacturer,
the degree of protection provided by the equipment may be impaired.
Waste electrical and electronic equipment (WEEE) must be collected
separately!
LONGO LPC-2 complies to the following standards:
•EMC: EN 61000-6-3:2007 + A1:2011, EN 61000-6-1:2007, EN 61000-
3-2:2006 + A1:2009 + A2: 2009, EN 61000-3-3:2013
•LVD: IEC 61010-1:2010 (3rd Ed.), IEC 61010-2-201:2013 (1st Ed.)
Smarteh d.o.o. operates a policy of continuous development.
herefore we reserve the right to make changes and improvements to
any of the products described in this manual without any prior notice.
MANUFAC URER:
SMAR EH d.o.o.
Poljubinj 114
5220 olmin
Slovenia
ii

Longo programmable controller LPC-2.DD4
Longo programmable controller LPC-2.DD
1 ABBREVIA IONS................................................................................1
2 DESCRIP ION...................................................................................2
3 FEA URES.......................................................................................3
4 OPERA ION.....................................................................................4
4.1 Parameters..............................................................................4
4.2 Dimmer type setting...................................................................7
5 INS ALLA ION..................................................................................8
5.1 Connection scheme....................................................................8
5.2 Mounting instructions................................................................10
5.3 Module labeling.......................................................................12
6 ECHNICAL SPECIFICA IONS................................................................13
7 SPARE PAR S..................................................................................14
8 CHANGES .....................................................................................15
9 NO ES..........................................................................................16
iii

Longo programmable controller LPC-2.DD4
1 ABBREVIATIONS
LED Light emitting diode
MOSFE Metal oxide semiconductor field effect transistor
AC Alternating current
DC Direct current
1

Longo programmable controller LPC-2.DD4
2 DESCRIPTION
LPC-2.DD4 module is a 4 channel MOSFE dimmer drive intended for dimmable lights (e.g., LEDs,
CFLs, incandescent).
Module can also be used for driving AC motors. It is an excellent replacement for traditional relay
fan speed regulation. Using LPC-2.DD4 module, step-less fan speed regulation is achieved.
Operational power supply is 90 .. 264 V AC, 50/60 Hz or 11.5 .. 30 V DC.
LEDs indicate state of signal present on corresponding module output. heir brightness corresponds
to the output setting.
LPC-2.DD4 is controlled and powered from the main module (e.g., LPC-2.MC8, LPC-2.MC9) via Right
internal bus. Loads are powered from external power supply which is connected to PS connector.
2

Longo programmable controller LPC-2.DD4
3 FEATURES
Figure 1: LPC-2.DD4 module
Table 1: Features
4 channel MOSFE dimmer drive for dimmable lights or AC motor fans.
Operational power supply 90 .. 264 V AC, 50/60 Hz or 11.5 .. 30 V DC.
Max. power consumption at 230 V AC is 210 VA on L1/Q1 and 150 VA on L2/Q2, L3/Q3, L4/Q4.
Overload protected.1
SW adjustable trailing-edge or leading-edge dimmer type, separately for each one of 4 channels.
SW adjustable fade-in and fade-out time effect, separately for each one of 4 channels.
Phase dependent driver for output which makes this module a lot more resistant to electrical
disturbances than commonly used amplitude dependent drivers.
Standard DIN EN50022-35 rail mounting
1 Protected against overloads that lasts for less than 5 minutes.
3

Longo programmable controller LPC-2.DD4
OPERATION
Module parameters can be read or written via Smarteh IDE software.
.1 Parameters
If parameter is set to logical “1”, is considered to be active, enabled or set. If parameter has logical
value “0”, is considered to be inactive, disabled or cleared.
Parameter can be an output, input, status or setting. Output and input parameters correspond to
the physical output and input pins of the module. Status parameters are used for additional
information from the module, where setting parameters are used to select different settings on the
module.
Output:
L1/Q1 – Dimmer output [OUT1]: Output setting
ype: UIN
If PSINtype
is “0”:
Raw to engineering data: 500 .. 10000 5.00 .. 100.00 %→
1 .. 499 Output off with fade-out effect→
0 Immediate output off→
is “1”:
Raw to engineering data: 2 .. 10000 0.02 .. 100.00 % →
1 Output off with fade-out effect→
0 Immediate output off→
L2/Q2 – Dimmer output [OUT2]: Output setting
ype: UIN
If PSINtype
is “0”:
Raw to engineering data: 500 .. 10000 5.00 .. 100.00 %→
1 .. 499 Output off with fade-out effect→
0 Immediate output off→
is “1”:
Raw to engineering data: 2 .. 10000 0.02 .. 100.00 % →
1 Output off with fade-out effect→
0 Immediate output off→
L3/Q3 – Dimmer output [OUT3]: Output setting
ype: UIN
If PSINtype
is “0”:
Raw to engineering data: 500 .. 10000 5.00 .. 100.00 %→
1 .. 499 Output off with fade-out effect→
0 Immediate output off→
4

Longo programmable controller LPC-2.DD4
is “1”:
Raw to engineering data: 2 .. 10000 0.02 .. 100.00 % →
1 Output off with fade-out effect→
0 Immediate output off→
L /Q – Dimmer output [OUT4]: Output setting
ype: UIN
If PSINtype
is “0”:
Raw to engineering data: 500 .. 10000 5.00 .. 100.00 %→
1 .. 499 Output off with fade-out effect→
0 Immediate output off→
is “1”:
Raw to engineering data: 2 .. 10000 0.02 .. 100.00 % →
1 Output off with fade-out effect→
0 Immediate output off→
Setting:
Fade-in effect timer for L1/Q1 [OUT1FadeInTimer]: ime of fade-in effect from 0 % to
100 % output setting.
ype: USIN
Raw to engineering data: 0 .. 36 3.6 s (default value)→
37 .. 100 3.7 .. 10 s→
Fade-in effect timer for L2/Q2 [OUT2FadeInTimer]: ime of fade-in effect from 0 % to
100 % output setting.
ype: USIN
Raw to engineering data: 0 .. 36 3.6 s (→default value)
37 .. 100 3.7 .. 10 s→
Fade-in effect timer for L3/Q3 [OUT3FadeInTimer]: ime of fade-in effect from 0% to
100 % output setting.
ype: USIN
Raw to engineering data: 0 .. 36 3.6 s (→default value)
37 .. 100 3.7 .. 10 s→
Fade-in effect timer for L /Q [OUT4FadeInTimer]: ime of fade-in effect from 0 % to
100 % output setting.
ype: USIN
Raw to engineering data: 0 .. 36 3.6 s (→default value)
37 .. 100 3.7 .. 10 s→
Fade-out effect timer for L1/Q1 [OUT1FadeOutTimer]: ime of fade-out effect from
100 % to 0 % output setting.
ype: USIN
Raw to engineering data: 0 3.6 s (→default value)
1 .. 100 0.1 .. 10 s→
5

Longo programmable controller LPC-2.DD4
Fade-out effect timer for L2/Q2 [OUT2FadeOutTimer]: ime of fade-out effect from
100 % to 0 % output setting.
ype: USIN
Raw to engineering data: 0 3.6 s (→default value)
1 .. 100 0.1 .. 10 s→
Fade-out effect timer for L3/Q3 [OUT3FadeOutTimer]: ime of fade-out effect from
100 % to 0 % output setting.
ype: USIN
Raw to engineering data: 0 3.6 s (→default value)
1 .. 100 0.1 .. 10 s→
Fade-out effect timer for L /Q [OUT4FadeOutTimer]: ime of fade-out effect from
100 % to 0 % output setting.
ype: USIN
Raw to engineering data: 0 3.6 s (→default value)
1 .. 100 0.1 .. 10 s→
Dimmer type for L1/Q1 [OUT1DimmerType]: Selection between leading-edge type and
trailing edge type. See chapter 4.2. Applicable only when PSINtype = 0 (AC).
ype: BOOL
Raw to engineering data: “0” Leading-edge→
“1” railing-edge→
Dimmer type for L2/Q2 [OUT2DimmerType]: Selection between leading-edge type and
trailing edge type. See chapter 4.2. Applicable only when PSINtype = 0 (AC).
ype: BOOL
Raw to engineering data: “0” Leading-edge→
“1” railing-edge→
Dimmer type for L3/Q3 [OUT3DimmerType]: Selection between leading-edge type and
trailing edge type. See chapter 4.2. Applicable only when PSINtype = 0 (AC).
ype: BOOL
Raw to engineering data: “0” Leading-edge→
“1” railing-edge→
Dimmer type for L /Q [OUT4DimmerType]: Selection between leading-edge type and
trailing edge type. See chapter 4.2. Applicable only when PSINtype = 0 (AC).
ype: BOOL
Raw to engineering data: “0” Leading-edge→
“1” railing-edge→
Power supply input type [PSINtype]: Selection on what kind of power supply for loads is
connected to N/+U and L/ .⏊
ype: BOOL
Raw to engineering data: “0” AC→
“1” DC→
6

Longo programmable controller LPC-2.DD4
Status:
Timer of overload protection [OverloadTimer]: imer countdown until the output is switched on
again (after output overload).
ype: UIN
Raw to engineering data: 0 overload protection is switched off→
1 .. 200 0.1 .. 20 s→
.2 Dimmer type setting
Table 2: Dimmer type setting for type of load
Dimmer type setting Oscillogram of 50 %
chopped sinus wave Load types
Leading-edge Inductive character loads, e.g. AC motor.
railing-edge
Resistive and capacitive character loads,
e.g. lights.
NO E: When using LPC-2.DD4 to control dimmable lights, check manufacturer dimmer type
recommendation. Set LPC-2.DD4 accordingly.
NO E: Using LPC-2.DD4 set as trailing-edge dimmer type controlling inductive load or using
LPC-2.DD4 set as leading-edge dimmer type controlling capacitive load, may result in LPC-2.DD4
module failure.
7

Longo programmable controller LPC-2.DD4
5 INSTALLATION
5.1 Connection scheme
Figure 2: Connection scheme2
AC power supply DC power supply
NO E: Correct dimmer type setting of LPC-2.DD4 module is essential. In-correct dimmer type
setting for certain type of connected load may result in output failure. See chapter 4.2 for
correct setting depending on the type of connected load.
NO E: AC motor shall only be connected to L1/Q1 terminal on LPC-2.DD4 module.
NO E: Circuit breaker, fuse, switch etc. is only allowed to be connected in series
with LPC-2.DD4 PS.1 or/and PS.2 terminal. Using circuit breaker, fuse, switch etc.
in series with LPC-2.DD4 module output terminals and load can result in
LPC-2.DD4 module failure.
2 Outputs must not be connected together. Use only same type of load on same output.
8

Longo programmable controller LPC-2.DD4
Table 3: PS
PS.1 N/+U
Power supply input for loads
AC: neutral
DC: 11.5 .. 30 V DC
PS.2 L/ ⏊
Power supply input for loads
AC: line 90 .. 264 V AC, 50/60 Hz
DC: GND
Table : OUT
OU .3 L1/Q1 MOSFE dimmer output for AC motors or
lights
OU .4 L2/Q2 MOSFE dimmer output for lights only
OU .5 L3/Q3 MOSFE dimmer output for lights only
OU .6 L4/Q4 MOSFE dimmer output for lights only
Table 5: K1
Internal BUS Data & DC power supply Connection to I/O module
Table 6: K2
Internal BUS Data & DC power supply Connection to I/O module
Table 7: LEDs
LED1: green Dimmer output state
ON (gradually): L1/Q1 output on
(conductive)
OFF: output not powered
LED2: green Dimmer output state
ON (gradually): L2/Q2 output on
(conductive)
OFF: output not powered
LED3: green Dimmer output state
ON (gradually): L3/Q3 output on
(conductive)
OFF: output not powered
LED4: green Dimmer output state
ON (gradually): L4/Q4 output on
(conductive)
OFF: output not powered
9

Longo programmable controller LPC-2.DD4
5.2 Mounting instructions
Figure 3: Housing dimensions
Dimensions in millimeters.
All connections, module attachments, loads replacement and
assembling must be done while module is not connected to the power
supply.
Mounting instructions:
1. Switch off main power supply.
2. Mount LPC-2.DD4 module to the provided place inside an electrical panel (DIN EN50022-35
rail mounting).
3. Mount other LPC-2 modules (if required). Mount each module to the DIN rail first, then
attach modules together through K1 and K2 connectors.
4. Connect digital inputs and outputs wires according to the connection scheme in Figure 2.
5. Check that every output has correct dimmer type setting selected. See chapter 4.2.
6. Switch on main power supply.
Dismount in reverse order. For mounting/dismounting modules to/from DIN rail a free space of at
least one module must be left on the DIN rail.
NO E: LPC-2 main module should be powered separately from other electrical appliance connected
to LPC-2 system. Signal wires must be installed separately from power and high voltage wires in
accordance with general industry electrical installation standard.
10
53
90
95
36
60

Longo programmable controller LPC-2.DD4
Figure : Minimum clearances
he clearances above must be considered before module mounting.
11

Longo programmable controller LPC-2.DD4
5.3 Module labeling
Figure 5: Label
Label (sample):
Label description:
1. XXX-N.ZZZ - full product name.
◦XXX-N - Product family
◦ZZZ - product
2. P/N: AAABBBCCDDDEEE - part number.
▪AAA - general code for product family,
▪BBB - short product name,
▪CCDDD - sequence code,
•CC - year of code opening,
•DDD - derivation code,
▪EEE – version code (reserved for future HW and/or SW firmware upgrades).
3. S/N: SSS-RR-YYXXXXXXXXX - serial number.
◦SSS – short product name,
◦RR – user code (test procedure, e.g. Smarteh person xxx),
◦YY – year,
◦XXXXXXXXX – current stack number.
4. D/C: WW/YY - date code.
•WW – week and
•YY – year of production.
Optional
1. MAC
2. Symbols
3. WAMP
4. Other
12
XXX-N.ZZZ
P/N: AAABBBCCDDDEEE
S/N: SSS-RR-YYXXXXXXXXX
D/C: WW/YY

Longo programmable controller LPC-2.DD4
6 TECHNICAL SPECIFICATIONS
Table 8: Technical specifications
Power supply3from internal BUS
Power consumption31 W
Rated power supply input for loads
on PS connector
AC: 115/230 V AC, 50/60 Hz
DC: 12/24 V DC
Operational power supply input for
loads on PS connector
AC: 90 .. 264 V AC, 50/60 Hz
DC: 11.5 V .. 30 V DC
Rated load current on channel
L1/Q1 0.9 A
Rated load current on channel
L2/Q2 0.65 A
Rated load current on channel
L3/Q3 0.65 A
Rated load current on channel
L4/Q4 0.65 A
Number of drive outputs 4
Load capacitance4max. 1 µF
Fuse no
Connection type screw type connectors for stranded wire 0.75 to 2.5 mm2
Dimensions (L x W x H) 90 x 53 x 60 mm
Weight 70 g
Ambient temperature 0 to 50 °C
Ambient humidity max. 95 %, no condensation
ransport and storage temperature -20 to 60 °C
Pollution degree 2
Overvoltage category II
Electrical equipment Class II (double insulation)
Protection class IP 30
3 Of internal logic only.
4 Applicable when using DC power supply input.
13

Longo programmable controller LPC-2.DD4
7 SPARE PARTS
For ordering spare parts following Part Numbers should be used:
LPC-2.DD4 module, 4 channel dimmer module
LPC-2.DD4 P/N: 225DD419001002
14

Longo programmable controller LPC-2.DD4
8 CHANGES
he following table describes all the changes to the document.
Date V. Description
24/07/19 1 he initial version, issued as LPC-2.DD4 module UserManual.
15

Longo programmable controller LPC-2.DD4
9 NOTES
16