Smartenit ZBMLCSR User manual

[phone]
Smartenit.com
Technical Support
© 2018 Compacta International, Ltd.—Rev 10/3/2018
ZBMLCSR and Smartenit are trademarks of Compacta International, Ltd
Zigbee is a registered trademark of the zigbee alliance
Quick Start Guide
Wireless Metering Switch (Load Controller)
ZBMLCSR Model #4040C
About this Product
This high power switch is ideal to wirelessly moni-
tor and control higher voltage (up to 240VAC)
and/or high current (up to 40A) appliances such
as electric water heaters, pool pumps, booster
pumps, etc. The device interfaces wirelessly with-
in IoT/Home Automation networks where it can
be controlled by automation hubs using the
Zigbee protocol.
For energy monitoring/management, the device
measures the energy consumed as well as other
parameters such as power, voltage, current, pow-
er factor, etc.
Install with the tips and suggestions below to get
the benets of the Internet of Things through
your automation controller.
Installation
For outdoor installation, it is imperative that all water tight precautions are taken to ensure the life and safe-
ty of your load controller.
The device can be installed indoors or outdoors and may
be mounted to a junction box or panel through the pro-
vided 3/4” connector, or to a surface through the readily
accessible mounting holes on the back of the unit. An
optional mounting kit consisting of four mounting tabs
and screws is sold separately. Using this kit does not re-
quire opening the device.
When mounting outdoors through exible conduit, a wa-
ter-tight connector (such as 3/4NPT #P472) must be
used.
To maintain its water tight
specication, the device
uses a seal on its lid that
that matches a “lip” on the
case bottom. If opening
the device to change the connector or to mount it through the internally accessible
holes, disconnect the electrical supply and do not disturb the sealing gasket or
damage the sealing lip when closing it. Avoid overtightening the lid screws to main-
tain case integrity and water tightness.
Optional Mounting Kit
Wire Color Connect To
Black Electrical service line 1 (120V: Hot, 240V: L1)
White Electrical service line 2 (120V: Neutral, 240V: L2)
Red Electrical load
LOAD LED—Green if the
load is energized (switch
is ON)
SET Pushbutton—
Toggles switch on/o,
restores factory settings,
joins device to network,
binds to other devices.
STATUS LED—Indicates
network and binding status
Typical 220V Installation

[phone]
Smartenit.com
Technical Support
© 2018 Compacta International, Ltd.—Rev 10/3/2018
ZBMLCSR and Smartenit are trademarks of Compacta International, Ltd
Zigbee is a registered trademark of the zigbee alliance
Quick Start Guide
Setup
1) Factory Reset (Restore Factory Settings)
While powering the device, press the SET button and release it once the device powers up. Alternatively, if
the device is already joined to a Zigbee network, quickly tap the SET button 13 times. The Status LED will go
out for 1 second and then begin ashing rapidly. The ZBMLCSR will then search for an open Zigbee net-
work to join.
2) Joining device to a Zigbee network
1. Set network controller to discover devices (Open Permit Join)
2. As the ZBMLCSR joins, the Status LED blinking rate will slow until it stays solid, indicating it has fully
joined the Zigbee network.
3) Binding to be controlled by other devices
To allow On/O control by another device, tap the SET button once quickly and within 1/2 second press
and hold it for 3 seconds. The Status LED will blink per the pattern described in the Status LED Indications
table above.
4) Allowing other devices to join Zigbee network (Open Permit Join)
As a Zigbee “Router”, the ZBMLCSR can also be put in discovery mode to permit other devices to join the
Zigbee network. Do note that ultimately the network manager device will decide whether to allow the new
device to fully join. Assuming the ZBMLCSR is already in a Zigbee network, it can open the network for oth-
er devices to join as follows:
1. Press and hold the SET button for 6 seconds. The STATUS LED will blink once per second and the net-
work will be open for joining for up to 4 minutes
2. Permit-join can be stopped by pressing and holding the SET button for 3 seconds. The LED will stop
blinking.
SET Pushbutton Functionality
Operation Pushbutton Device Behavior
Leave Network Tap 13 times Status LED will begin
fast blinking
Close Permit Join Press and hold for 3
seconds when de-
vice is in open per-
mit join
Status LED will stop
ashing
Soft Reset (Reboot
Device)
Tap 10 times
Request Firmware
Update (OTA)
Tap 6 times
Restore Factory Set-
tings
Tap 9 times
Status LED Indications
Pattern Indication
Fast Flashing Searching for network
Solid Joined to network
Flash once per second Open permit join
Short blip, pause-0.5 secs Binding to Endpoint 1
(On/O)
2 blips per second Disconnected from net-
work
Load LED Indication
Color Indication
O Load is de-energized