Smartenit ZBMLC30 User manual

Where the smart things are
®
sm
2015 Compacta International, Ltd. - Rev. 8/2015
ZBMLC30 and Smartenit are trademarks of Compacta International, Ltd.
ZigBee is a registered trademark of the ZigBee Alliance
[phone]
Technical Support
Smartenit.com
Quick Start Guide - ZBMLC30 Model #4040B
Product Brief
Installation
Local Control & LED Indicators
Wireless Triple-Relay Metering Load Controller
The ZBMLC30 interfaces wirelessly with ZigBee Pro controllers and
gateways in the Home Automation (HA) prole. This high power
load controller is ideal for applications that require control and
monitoring of loads up to 240VAC at 30Amps.
The device measures the energy delivered to the load in Kilo-
watt-Hours, enabling the intelligent management of large applianc-
es to maximize energy conservation. Two-speed appliances such
as pool pump motors are handled directly with an integrated third
relay.
Line 2 Out
Line 1 In
Load 1 Out
Load 2 Out
Line 2 In
The ZBMLC30 can be mounted indoors or outdoors
Mounting
Can be mounted with #6 screws through mounting holes from the inside or
with optional Mounting tabs (sold separately). For water tight operation,
all four mounting holes must be used or otherwise sealed.
Mounting Tabs
(sold separately)
Wire Connections
LOAD LED STATUS LED
SET
Pushbutton
SET Pushbutton - used to factory reset device, join
network, bind to other devices, and for local control. A
single tap cycles loads from OFF, to Load 2 ON (Red LED),
to Load 1 ON (Green LED) with each successive tap.
Load LED - Indicates when load is energized (Green if high
power, Red if low power. Green/Red ashing, both loads
on)
Status LED - Indicates network join and bind status.
** High voltage installations should always be performed by a licensed professional **
Wire Color Make Connection To
Black Electrical service Line1 (Hot for 120VAC or L1 for 240VAC)
Brown Electrical service Line2 (Neutral for 120VAC or L2 for 240VAC)
Red L1 to Load 1 (High Speed if 2-speed appliance)
Yellow L1 to Load 2 (Low speed if 2-speed appliance)
Blue L2 to Load (Common to Load 1 and Load 2)
Mounting Holes
A water tight
connector
and conduit
must be used
for outdoor
installation

Where the smart things are
®
sm
[phone]
Technical Support
Smartenit.com
2015 Compacta International, Ltd. - Rev. 8/2015
ZBMLC30 and Smartenit are trademarks of Compacta International, Ltd.
ZigBee is a registered trademark of the ZigBee Alliance
SET Pushbutton Additional Operation
Desired Operation Action on Pushbutton Device Behavior
Leave Network Press and hold for 15~17
seconds (works like a
factory reset, but preserves
meter calibration settings)
Status LED will begin
Fast Flashing
Close Join Press and hold for 3
seconds when device is in
Open Join
Status LED will stop
ashing
Soft Reset Tap 10 times both LEDs will go out
for about a second and
then device will rejoin
network
Request New Firmware
via OTA
Tap 6 times LED will quick blip o,
once every second
while in OTA progress
Enable for Control4
networks
Press and hold for 10 ~ 12
seconds
Status LED will blink 3
times
Status LED Indication
Pattern Indication
Fast ashing Searching for network
Solid Joined network
Flash once per second Open Permit Join
Short blip, pause - 5 sec. Bind to Load1 Out
Fast Flash - 5 sec. Bind to Load2 Out
2 blips per second Disconnected from network
Load LED Indication
Color Indication
O No power on load
Red Load 2 (yellow wire) On
Green Load 1 (red wire) On
Green/Red Flashing Load 1 and Load 2 On
(Both loads can only be
turned on via ZigBee)
Open Permit Join
The ZBMLC30 also serves as a router and allows other ZigBee HA devices to join the network. After
the ZBMLC30 has already joined the network (Status LED is solid) proceed as follows:
1. Press and hold the SET button for 6 seconds. The Status LED will blink once per second while in permit
join mode. The ZBMLC30 will allow joining of other devices for up to 4 minutes.
2. Join the new ZigBee HA device to the network according to the join method of that device.
3. Permit-join can be terminated by pressing and holding the SET button for 3 seconds.
Setup
1) Factory Reset ZBMLC30
• Press SET button on your ZBMLC30 while powering device and release. Alternatively, if the device has already
joined a ZigBee network, press the SET button for at least 20 seconds and release. The Status LED will go out
for 1 second and then begin ashing rapidly. The ZBMLC30 is now searching for an open ZigBee HA network
to join to.
2) Joining the ZBMLC30 to the Network
• Open a ZigBee HA router or coordinator to permit joining of your ZBMLC30 to the network.
• As the ZBMLC30 begins to join, the Status LED blinking rate will slow until fully joined, when it’ll be lit solid.
3) Binding the ZBMLC30 to other devices
• To bind Load1 Out to a ZigBee HA controller, tap the SET button once quickly and within 1/2 second press and
hold it for 3 seconds. The Status LED will begin to blink (refer pattern in table below). Then press the Program
Button on the client device(such as a switch) according to the instructions of that device.
• To bind Load2 Out to a ZigBee HA controller, tap the SET button twice quickly and and within 1/2 second press
hold it for 3 seconds. The Status LED will begin to blink fast (refer to pattern in table below). Then press the
Program Button on the client device(such as a switch) according to the instructions of that device.
• Binding time window varies by coordinator.