Smeg K143X User manual

Page 1 of 3
Installation, Use and
Maintenance Manual
OVEN HOOD K143X
Introduction
Dear Customer, we hereby thank you for choosing our Oven Hood
and hope you will be satisfied with our product.
1. Instructions
The following instruction manual is an integral part of the equipment
and must be at the operators’ disposal for advice until the end of the life
cycle of the product.
Before carrying out any operations, carefully read the information
contained in the manual about safe installation, use and maintenance.
The equipment is only intended for the use it has been designed for,
by qualified and skilled personnel.
Installation, maintenance and repair operations must only be carried
out by an authorized technical service centre or qualified personnel, in
compliance with the regulations in force and according to the instructions
provided by the manufacturer.
When using it for the first time, make sure that the hood conveyor
connected to the exhaust ducts of the oven is positioned correctly, to
prevent vapour leakage. It is recommended to make sure that the
connection between the ducts and the oven is well sealed every time the
hood or the oven on which it is installed are moved.
The equipment must be earthed in accordance with the safety
regulations of the electrical system.
The plug to be connected to the power cable must be compliant with
the regulations in force.
Do not block the openings, the heat ventilation and exhaust slits.
Use the hood at an ambient temperature between +5 °C and +35 °C.
This appliance is intended for professional use and complies with the
EC directives in force. The appliance functions must be considered as a
oven hood, therefore any other use of the device is improper.
The Manufacturer refuses all responsibility for direct and indirect
damage caused by improper installation, tampering with, inadequate
maintenance, improper use and failure to comply with the regulations
contained in the instruction manual.
2. Installation
All the materials, with the exception of silicone, used for installation
must resist a temperature of 150 °C without generating strains and/or
surface defects.
2.1 - Positioning
The Oven Hood must be positioned on the oven, after must be
fixed the conveyor by screws , that will be fixed to the rear oven’s back
(Fig. 1).
Figure 1
2.2 - Electrical connection
The electrical connection, single phase 220 – 230 V ~ 50Hz, must
be carried out by qualified personnel in compliance with the European
regulations in force.
The Oven hood is supplied with electric cable and plug. If the plug
is replaced, it must be compatible with the maximum power of the hood.
It is recommended to have the installation done by a qualified electrician,
in compliance with the regulations in force.
Attention!!! – A bipolar safety switch must be set upstream of the hood.
Attention!!! – The equipment must be earthed properly according to the
safety regulations of the electrical system.
Conveyor

Page 2 of 3
2.4 – Operation
The Oven Hood will be turned on by the front switch (Fig. 2)
Figure 2
3. Maintenance
Attention!!! – Before carrying out any maintenance operations, turn off
the current by using the appropriate switch or disconnecting the plug.
Attention!!! – Any maintenance operation must be carried out by
qualified personnel only.
Maintenance operations may include the removal the panel
cover. To remove the panel cover unscrew the perimetric screws (Fig. 3)
and take care not to damage the electric cables when lifting the cover.
Figure 1
Attention!!! – When removing the panel, handle them with great
attention by using gloves to protect hands from possible cuts.
3.1 – Disassembling labyrinth filters
To disassemble the filters, grab and slide them upwards so that they
slip out of the lower guide. Rotate the lower wall slightly to release the
filter completely. To reassemble the filters, follow the procedure
reversely.
3.2 – Disassembling the fan
The fan is removed by removing the cover and disconnecting the
same from the cable. After removing the front cover to which is attached
the fan you can proceed to remove the screws that fixed the fan to the
cover.
3.3 – Disassembling the switch ON OFF
Before removing the switch must be removed the cover panel
mounted on the oven hood, fixed by screws (Fig. 4).
Figura 2
3.5 Spare parts
It is possible to use original or authorized spare parts only. Do not
repair or replace any components of the oven hood that have not been
recommended by this manual. All the other interventions must be carried
out by authorized technical personnel. To ask for a spare part, indicate
the hood model specified on the label.
The spare parts that can be supplied are the following:
I. Switch ON OFF black 10 A;
II. Fan 7/7 - 145 W 4P;
III. Labyrinth filter 400 x 350 mm - GF032;
IV. Eletrical wiring;
V. Fixing brackets to the oven.
Switch
cover
Switch
Cover pannel

Page 3 of 3
4. Cleaning
Attention!!! – Never use detergents containing: sand, caustic soda, acids
or chlorides thatmight corrode the surface.
Attention!!! – Carry out any cleaning operation cutting off the power
supply first
The hood must be cleaned by using a damp cloth with non-
abrasive detergent and drying the surfaces with a dry cloth.
Figura 3 – Electrical connection.