Smeg LB86-1 User manual

Instructions for Use
Washing machine

239726
Thank you for your confidence in purchasing our washing machine, and congratulations on the
excellent choice.
Your new washing machine meets the requirements of modern treatment of laundry. It is rational in
the consumption of energy, water and washing agents.
Our appliances are friendly to the environment. Some of the materials may be recycled, others
deposited or decomposed. To avoid pollution of environment, once your appliance is no longer
useful, take it to your local authorized waste appliance dealer.
The appliance is intended exclusively for use in households. If the appliance is used for
professional purposes, for profit, or for purposes beyond regular use in a household, or if appliance
is used by a person who is not a consumer, the warranty period equals the shortest warranty period
possible as stipulated by the relevant legislation.
Description of washing machine ..................................3
Cautions ..........................................................................4
Installation and connection...........................................5
Operation.........................................................................8
Tips for washing and energy saving ..........................15
Cleaning and maintenance..........................................17
Failures..........................................................................19
Tables ............................................................................23
2

239726
1. Front panel
2. Detergent dispenser
3. Door
4. Filter lid
5. Adjustable legs
6. Water outlet hose
7. Water inlet hose
8. Mains power cable
Dimensions (w x d x h): 600 mm x 600 mm x 850 mm
Dimensions (w x d x h): 600 mm x 440 mm x 850 mm
Depth with door open: 106 cm / 88 cm (depending on model)
Weight (net): 90 kg / 76 kg (depending on model)
Nominal voltage: 230 V, 50 Hz
Power: 2300 W / 2000 W (depending on model)
Max. load: 7 kg / 6 kg / 4,5 kg (depending on model)
Power socket: (230 V, 50 Hz, 10 A)
Water pressure: min. 0,05 MPa, max. 0,8 MPa
Fuse: 10 A
3
Description of washing machine
Technical information
(depending on model)

239726
• Be sure to remove transport brackets prior first use of the appliance. Attempted operation of the
blocked machine may result in irreparable damage which is not covered by the manufacturer’s
warranty!
• When connecting your washing machine to water supply, be sure to use brand new water inlet
hose and appropriate sealing gaskets (attached).
• Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be
damaged if frozen.
• Install the washing machine in a perfectly horizontal position, on solid flat concrete floor.
• Follow the instructions for correct installation and water and mains connections.
• Never immerse the end of the drain hose into the draining water.
• Prior starting the washing cycle lock the door by pressing them at the designed spot.
• Door may not be open during the washing cycle.
• Use only detergents and softeners for machine wash. Manufacturer may not assume responsibility
for any damage and eventual discoloring of gaskets and plastic components as a consequence of
incorrect use of bleach and/or coloring agents.
• For removal of lime residues use such agents with added anti-corrosion agents. Follow the
manufacturer’s instructions. Finish the lime removal by multiple rinsing to remove completely
eventual acid residues.
• Never use detergents containing solvents, since there is a danger of creating toxic gasses which
may damage the machine and result in ignition or explosion.
• Upon completion of washing operation close the water faucet.
• Before any transport block the machine by inserting at least one transport blocking rod. Prior this
operation disconnect the appliance from the mains power!
• Rating plate with basic information is located above the opening of the machine.
• The warranty shall not apply to consumables (bulbs), minor discoloration or deviations of color,
increased noise level as a consequence of appliance age, which does not affect appliance
functionality, and aesthetical deficiencies which do not affect appliance functionality or safety.
• The appliance is manufactured in compliance with all relevant safety standards; however, it is
recommended that persons with impaired physical, motional, or mental abilities, or persons with
inadequate experience and knowledge, do not use the appliance without due supervision. The
same recommendation applies to minors using the appliance.
Before connecting the appliance read these instructions carefully. Repairing the failure
arising from inappropriate connections or use of the appliance is not covered by the
guarantee.
The symbol on the product or on its packaging indicates that this product may not
be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of this product. For more
detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or the shop where you purchased the
product.
4
Cautions

239726
In removing the wrapping be careful not to damage the
appliance with a sharp object.
Before connecting the appliance, let it warm up to room
temperature (wait for two hours).
• Our appliances are packed in environmentally friendly materials
which may be recycled, deposited or decomposed without any
threat to the environment.
• To this end all wrappings are marked accordingly.
• Move the pipes.
• Loosen screws A at the rear of the machine (Fig. 1).
• Remove the brackets B (Fig. 1) and slide them into the groove
on the blocking rod (Fig. 2) - the right one should be turned
around.
• Use the brackets to rotate blocking rods for 90° and pull them
out.
• Close the openings with attached plastic pegs.
Save transport brackets for eventual later use.
Be sure to remove the transport brackets prior first
use, otherwise the appliance may be permanently
damaged. In such cases the warranty conditions are
void.
Fig. 1 Fig. 2
• Put the appliance in horizontal position by turning the adjustable
legs. The legs are adjustable up to +/- 1 cm.
After the adjustment tighten the nuts firmly (A) - towards
the bottom of the machine!
Vibrations, moving of the appliance and loud operation
due to incorrect setting of the adjustable feet shall not
be covered by this warranty.
The appliance should be placed on a surface with
concrete base; the surface should be dry and clean in
order to prevent slipping. The adjustable feet should
also be cleaned before installation.
Package removalPackage removal
Removal of transport
brackets
Removal of transport
brackets
Leveling the applianceLeveling the appliance
5
Installation and connection

239726
• If you have a tumble dryer of the same dimensions, you can
place it on top of the washing machine.
To ensure correct operation of the appliance, water
pressure inlet must be between 0,05 and 0,8 MPa.
Minimum water pressure can be established by measuring
the quantity of poured out water. 3 litres of water must be
poured out from completely opened tap in 15 seconds.
• Take the water inlet hose from the drum and attach the inlet
hose angle extension (1) to the washing machine by screwing
it onto the provided thread (certain models only).
• Insert the gasket with a filter net into the straight inlet hose
attachment nut (2) and screw the nut onto the water tap. (With
some models, the gasket with filter net is already fitted and
any additional fitting into the nut on the straight attachment is
not required).
• In case of hot and cold water connection, connect one hose to
cold and other to hot water faucet as marked at the rear of the
appliance (letters C and H) (C - cold; H - hot)
The inlet hose should be tightened manually, firmly
enough to prevent any leaks. After tightening the hose,
check for any leaks.
Use of pliers, wrenches, or other similar tools is not
allowed when installing the hose, as these tools can
damage the nut thread.
Partial Aqua-stop (water stop system)
In case of damage on the interior pipe, leaking is prevented by
automatic closing system which stops water inlet to the machine.
In such cases display A turns red.
Inlet pipe must be replaced.
Complete Aqua-stop (certain models only)
In case of damage on the interior pipe, leaking is prevented by
automatic closing system which stops water inlet to the machine.
Security system also detects whether there is any water leakage
within the interior of the machine. In such cases washing is
suspended, machine switches on the pump and signals error.
Water inlet connectionWater inlet connection
6

239726
Do not immerse the Aqua-stop system inlet pipe into
the water, because it contains the electric valve!
• Fix the outlet hose to run into the sink or the bathtub, or connect
it directly to the wall drain outlet (diameter min. 4 cm).
• Wall drain must be installed properly and must enable
occasional cleaning.
• Fasten the outlet hose support with a piece of rope led through
the hose elbow, to prevent the hose from slipping to the floor.
The end of outlet hose should be placed between minimum 60
cm and maximum 100 cm above the floor level.
• Plug the mains power cable to the wall mains socket.
• Required voltage and other information are written on the rating
plate above the door opening of the machine.
The wall socket must be accessible at all times and
must be equipped with an earth lead (in accordance
with the local safety regulations).
The permanent connection must be fitted by an
authorized personnel only.
Damaged mains power cable may be replaced only by
the producer or his authorized personnel.
Never plug the appliance into the electric shaver socket
or hair dryer socket.
Water outlet connectionWater outlet connection
Connect the appliance to
the mains supply
Connect the appliance to
the mains supply
7

239726
A - program selector
B - lower spin RPM or spin off
knob (depending on the model)
C - quick or half program knob
(depending on the model)
D - elevated water level knob / cold wash
(depending on the model)
E - pump stop knob
F - START/PAUSE knob
Signal LED’s:
- washing program stages
•wash
•rinse
•spin
- Child lock
8
Program selector Basic programs Partial programs
Cotton
Pre-wash
Heavy duty
Easy iron
Quick program
Rinse
Synthetics
Pre-wash Softening
Delicate Pumping water
Wool Spinning
Manual wash
Mix
Cold wash
Operation

239726
• Open the door of the machine.
• Load the laundry into the drum.
• Close the door.
• Open the water inlet faucet.
• Push the ON/OFF button and select the program.
• Add washing and treatment agents (detergent and softener).
• Start the operation by pushing the START knob (F).
- Open the door of the machine.
Door is opened by pulling the handle (lever) on the right hand
side of the door towards you.
- Sort the laundry by the type of fabrics.
Do the buttons and zippers, tie the strings and pull out
the pockets.
Very delicate laundry should be put in a special
protective sack.
It is suggested to load the drum with items of different
sizes.
Pay attention to the labels on the clothes, indicating
the recommending washing mode (see table of
textile treatment symbols on the last page of these
instructions).
- Load the laundry into the drum.
Check that the drum is empty.
- Close the door of the appliance.
- Open the water inlet faucet.
- Push the ON/OFF button and select washing program.
Program is selected by turning the program selector (A) from the
“0” position to the desired washing program. The ON/OFF signal
LED indicating particular washing stage for the chosen program
starts flashing. The program selector (A) may be turned in both
directions, and the appropriate program selected according to the
type of laundry washed and the required washing temperature
(see Program Chart for help). You may select basic or partial
programs.
Select additional functions by pressing their relevant knobs (F).
- Selection of basic programs ( , , , , , , )
Basic programs represent integral programs containing all
washing stages, including softening and spinning (see Program
Chart). They are selected by turning the program selector (A) to
the appropriate position.
Cotton: whites/colored
Normally stained cotton and flax bed linen and underwear, table
Washing procedureWashing procedure
Washing machine
operation
Washing machine
operation
9

239726
cloth, bathroom towels, top garments, etc.
For heavily stained permanent press use the heavy duty
program, or program with the pre-wash .
For smaller loads (non-delicate cotton, linen, synthetic, and
mixed fabric) and smaller quantities of soiled laundry (laundry
refreshment, laundry wet with perspiration, etc.), we recommend
the use of the (17´ ) quick program. This way, you will
save both energy and time.
If you wish the laundry not to be excessively creased at the end
of washing, use easy ironing program .
Synthetics
Normally stained shirts, blouses and other polyester and
polyamide garments, or a mixture of these fabrics with cotton.
For heavily stained permanent press use program with pre-wash
.
Delicate
This is a program for delicate fabrics (dresses, skirts, blouses)
and curtains.
Wool
Especially gentle program for washing wool and garments made
from mixture of other fabrics with wool, appropriately marked for
machine washing.
Manual wash
Very gentle program concluded with short gentle spin (max. 400
RPM).
It is suitable for washing fabrics from flax, silk, wool or viscose,
marked accordingly for manual wash.
Mix (depending on the model)
Special program for washing normally stained colored laundry made
from various resistant fabrics at 30°C.
Cold wash (depending on the model)
Washing program for lightly soiled laundry of mixed fabrics (mixed
quality of fabrics).
- Selection of additional function (, , , , , , )
Additional functions after the basic washing cycle procedure.
Particular function is switched on by pressing the relevant knob.
The selection is confirmed with sound signal and switching on
the signal LED above the selected function. If certain function
is not available for the selected program, signal LED will not
illuminate.
The function is switched off by pressing the same button again
- signal LED goes off.
10

239726
Select the particular function after the selection of the
basic program, but prior pressing the START button (F).
Reduced spin RPM
• Reduction of spin RPM depends on program selection and
maximum RPM for particular type of machine.
Basic programs Spin speed - RPM
max. reduced
Cotton 1400/1300
1200/1100
1000/900/800
700
600
500
Synthetics, Mix,
Cold wash 1000/900/800 600
Delicate 700 0
Wool 600 0
Manual wash 400 0
Spin OFF (RPM - 700 RPM).
This knob switches off spin on all programs.
Quick program
• Convenient for washing less stained laundry.
• Washing time is reduced (see Program chart).
• By pressing the key quick program
on the program Cotton
30°C, activate the program Cotton 30°C - Quick
.
Half-program
• Used for washing smaller quantities of laundry.
• Reduced consumption of detergents and water, and shortens
washing time.
•
When the program Cotton 30°C is active press the Half Load
key to activate the program Cotton 30°C - Quick 17´ .
Higher water level (Water plus)
• For better rinse, which is important for extra sensitive skin to
detergents.
• For washing heavily stained laundry.
Cold wash
Each temperature related to a particular program (wool, cotton,
delicates, etc.) corresponds to a particular period of cold wash.
To select the desired program use knob (D) and select the cold
wash.
11

239726
Pump stop
• This function is switched on after the selection of a basic
program by pressing the knob (E). It may also be switched on
during the operation, prior last rinse. Indicator LED above the
washing cycle symbol is lit.
• The program stops at the end of last rinse, prior spinning:
laundry remains soaked in water and prevents crease, if you
are unable to remove it from the drum immediately after the end
of washing cycle.
• Indicator LED above the knob is flashing.
The selected program is completed by pushing the START
button (F), but you may also apply partial programs (pumping or
spinning), but you must first return the program selector (A) to
the “0” position for at least one second, prior selecting any of the
partial programs.
When program continues, indicator LED above the knob goes
off.
- Selection of partial programs ( , , , )
These are independent programs and may be used when you do
not need the entire washing program. In case you would like to
use more additional programs in a sequence, you must turn off
the appliance prior any new program selection (turn the program
selector to “0” for at least one second).
Rinse
Independent program for rinsing delicate laundry, without
intermediate spinning and with short final spin. You may use
it for rinsing manually washed delicate laundry.
You may engage the reduced spin RPM knob.
Softening
This program is intended for softening, bleaching or
impregnating of washed laundry. It is completed with
aggressive spinning at high RPM.
You may engage the reduced spin RPM knob.
Pumping the water out
Use it when the washing program was interrupted or if pump stop
function was engaged, and you only wish to pump the water out
of the drum, without spinning.
Spinning
Aggressive spinning for non-delicate laundry at high spin RMP.
You may engage the reduced spin RPM knob.
12

239726
- Adding washing and softening agents
(see Tips for washing and energy saving)
• pre-wash compartment
• main wash compartment
• softener compartment
If you do not apply the program which includes the pre-wash
feature, you may add washing detergent directly into the drum,
using the measuring vessel.
When adding softener, be careful to fill the dispenser
only up to the marked level.
Be sure to close the detergent dispenser when
opening/closing the appliance door.
• Push the START button (F). Sound signal confirms the start, the
LED indicating particular washing stages stops flashing. The
machine starts operating after a few seconds. If the door is not
properly closed after starting the operation, the washing stage
indicator LED starts flashing again after a few seconds. When
you close the door, the machine initiates the selected program.
• As each washing stage is completed the relevant washing stage
indicator LED goes off and the subsequent one goes on.
• In case you would like to alter the washing program after the
initiated washing operation, turn the program selector for one
second to the position “0”, followed by the selection of a new
program. Switching the machine off deletes any previously
selected additional functions(i.e. Pump stop), so they have to be
reactivated.
Upon switching OFF, all additional pre-selected
functions are deleted; therefore they must be switched-
ON again.
- End of operation
Flashing LED’s for particular washing stages indicate that the
program was completed.
• Sound signal indicates that you may now open the door of the
machine.
• Extract the laundry from the drum and remove any alien objects
from the door gasket.
• Leave the door ajar to allow the interior to dry.
• Close the water inlet faucet.
• Switch the machine off by turning the program selector to
position “0”.
Start the operation
13

239726
• Pull the power lead from th e socket and cut the power supply
from the mains.
• By the user
Selecting PUMP STOP function
Program is stopped when it comes to the PUMP STOP stage
(drum door remains closed all the time). Indicator LED above
the knob (E) starts flashing. Washing procedure is continued by
pressing the START knob (F).
Own (physical) interruption
You may stop the program by turning the program selector to the
position “0”. If there is water in the drum select one of additional
programs (pumping , spinning ) to empty the water and
terminate the program.
PAUSE knob
By pressing the PAUSE knob (F) program may be suspended
at any time. After certain time you may open the door if there is
no water in the drum, otherwise this is not possible. Program is
continued by pressing the START knob (F).
• Failures
Program is suspended in case a failure occurs. Signal LED’s
are flashing and sound signal is heard (see cf. Failures).
• Power failure
At electric cutout the program is interrupted, however, after the
power supply has been re-established, the program operation
automatically proceeds.
If a power failure occurs when the drum is still full of
water, be careful not to open the door before you pump
the water out.
• Child lock
- It is switched on by simultaneously pressing the elevated
water level knob (D) and half-load /short program
knob (C) for at least 3 seconds. Selection is confirmed by
the sound signal and illuminated signal LED. The function is
switched off following the same procedure.
-As long as the Child lock function is engaged you may not
alter the program or additional functions. You may merely
switch off the machine by turning the program selector (A)
to the position “0”. Child lock remains active even after the
appliance is switched off, and you have to disengage it if
you want to select a new washing program.
Special functionsSpecial functions
Interruptions
14

239726
• Setting the sound signal
The appliance has the possibility of setting stronger sound
signal. Press the Reduced spin RPM knob (B) (or Spin
off knob ) and switch the machine on. The selection of the
function is confirmed by the sound signal. The function is
disengaged following the same procedure.
• Before washing sort out the laundry according to the type, degree of dirtiness and color
resistance.
• Prior selecting the washing program consult the sewn tab with information on a particular piece
of laundry (see Maintenance Chart on the last page).
• Wash separately the new colored textile products for the first time.
• Wash heavily soiled laundry in small quantities and add more detergent.
• Treat stubborn stains with special stain remover, it will save energy.
• With lightly stained laundry select washing program without pre-wash, use short program and
select lower washing temperature. This way you may save up to 50% of energy.
• Avoid washing too little quantities of laundry because of energy saving and for better
performances of the appliance.
• The largest allowed quantity of dry laundry is indicated in the Program chart.
• Before washing empty the pockets, close zip fasteners, and remove any metal fasteners or
badges that might clog the drain or damage the laundry or drum interior.
• Loosen the stacked laundry prior inserting it into the drum.
• Use only detergents for machine wash.
• Add powder or liquid detergents according to the manufacturer’s instructions.
• If water hardness level exceeds 14°dH degrees, the use of water conditioner is required. Any
damage to the heater due to failure to use a water conditioning agent shall not be covered by
this warranty.
• Chlorine-based whitening agents are not recommended, as it can damage the heater.
15
Hardness
scale
Degree of hardness
°dH(°N) m mol/l °fH(°F) p.p.m.
1 - Soft < 8,4 < 1,5 < 15 < 150
2 - Medium 8,4 - 14 1,5 - 2,5 15 - 25 150 - 250
3 - Hard > 14 > 2,5 > 25 > 250
In case of hard water add detergent according to the Chart for
degree 1 and add appropriate quantity of water softener (see
manufacturer’s instructions).
Tips for washing and energy saving

239726
• If you do not apply the program which includes the pre-wash
feature, you may add washing detergent directly into the drum.
• If you use thick liquid softener it is recommended to dilute
it with water, to prevent clogging of dispenser compartment
ducts.
• Washing machine is equipped with the dispenser partition
gate, so you may pour liquid detergent also into the central
compartment (depending on model). If you use powder
detergent the gate is lifted up, and in case of liquid detergent it
is slid down.
• Liquid detergents are intended for main wash only, without
pre-wash.
• Insert particularly delicate linen (stockings, delicate female
underwear, etc.) into the special bag.
• High spin RPM leave less moisture in laundry which dries out
much quicker in the tumble dryer, thereby saving energy.
Do not put clods of detergent into the soap dispenser
as the tube in the washing machine may clog.
16

239726
Disconnect the washing machine from the mains
before cleaning!
• The casing should be cleaned with soft cloth and mild
detergent.
• The interior of the drum and the door gasket is cleaned by
washing at 60°C without laundry and adding half quantity of
detergent.
• Frequent use of low-temperature programs in combination
with liquid detergents can lead to development of germs which
cause odor in the washing machine.
To prevent this, it is recommended to run the Cotton 95°C
program without any laundry at least once per month, using
powder detergent.
• If necessary, clean the detergent dispenser. Pull it out from its
casing completely by pressing the flap (see Fig.).
• If necessary, clean the cover of the bung under the running
water.
• Wash it under running water using a brush, and dry it. Remove
any leftover dried detergent from the bottom of the casing.
17
Cleaning and maintenance

239726
• Clean the entire rinsing area of the washing machine with a
brush, especially the nozzles on the upper side of the rinsing
chamber.
• Clean frequently the water inlet hose screen under running
water.
• After each wash wipe the door rubber gasket. This will prolong
its useful life.
• Open the filter lid using flat screwdriver or similar tool.
• Filter needs occasional cleaning, especially following heavily
shaggy or old laundry. Before cleaning, drain any water from
the machine via drain pipe.
• Turn it anti-clockwise, pull it out and clean under running
water.
18

239726
• Insert the filter back as shown on the picture, and tighten by
turning it in clockwise direction. To ensure good sealing the
gasket surface (A) must be dirt free.
The washing machine automatically monitors the execution of particular functions during the
operation, and reports any detected failures. In such cases both signal LED’s start flashing in
certain sequence, accompanied by the audible signal, sounding in the same sequence as the
indicator LED’s flash. The flashing sequence changes in accordance with the nature of the
detected failure.
In some cases you may attempt removing certain failures yourself, so count the number of flashes,
repeating after certain pauses.
The machine signals failures immediately after detecting them and stops the program, except for
heater failure, where the machine completes the washing program without heating water.
Failures:
2 - Two flashes: door is not correctly closed
3 - Three flashes: inappropriate water intake
7 - Seven flashes: inappropriate water outlet.
In these cases, you will be able to remedy the failure by yourself (See Troubleshooting table).
1 - One flash: temperature sensor failure
4 - Four flashes: spinning sensor failure
5 - Five flashes: motor failure
6 - Six flashes: Heater failure
In these cases, turn off the machine, then turn it back on and repeat the program. If the failure
reoccurs, contact your nearest authorized service center. The LEDs will continue to flash until the
machine is turned off.
Interferences from the ambient (for example electrical wiring) could induce signalization of different
faults. In such cases:
- switch the appliance off, and wait for a few seconds;
- switch the appliance back on and repeat the washing program.
If the fault repeats, call authorized service shop.
Warranty shall not apply in case of failures due to interferences from the environment (lightning
stroke, power supply circuit faults, natural disasters).
19
Failures

239726
20
Failure Possible cause Remedy
The machine does not work
(indicator LED’s are not
illuminated).
Machine is not powered. Check if:
• power in the socket,
• the fuse is OK,
• plug is in the socket.
FAILURE 2
Washing program does not
start
• At the beginning of the
washing program: on/off
LED is flashing
• During washing: LEDs
periodically flash twice
Door is not properly closed. Push it towards the machine.
FAILURE 3
Water does not enter the
machine (after approx. 8
min the machine reports
failure - LEDs periodically
flash three times).
Disturbed water inlet. Check if:
• the water tap is open,
• inlet pipe net filter is clean.
Push the START button.
Water is leaking from the
machine.
Filter is not tightly screwed in.
Inlet pipe is not tightly screwed
to the machine or to the water
faucet.
Outlet pipe fell to the floor.
Tighten the filter properly.
Tighten the inlet pipe.
Affix the outlet pipe to the drain.
The machine moves during
operation.
The machine is not properly
leveled.
Transport brackets are not
removed.
Level the machine with the
adjustable legs.
Remove transport brackets.
The machine vibrates
during the spin.
Unevenly distributed laundry,
especially with very small
quantities (for ex. only the
bathrobe).
This is normal, the machine will
reduce the RPM if vibrations are
too strong.
Wash larger quantity of laundry.
Excessive foaming during
washing.
Excessive measure of
detergent.
Use washing powder according to
the instructions by the producer and
according to the water hardness
and soiled laundry.
Use only detergents for machine
washing.
FAILURE 7
Water is poorly pumped
out or not at all (machine
reports failure - the LEDs
periodically flash seven
times).
Water outlet is clogged Check if:
• the filter is clean,
• outlet pipe is not jammed,
• the drain is clogged,
• outlet pipe is positioned higher
than 1m.
Push START again
Laundry is not properly
spun.
No failure is reported.
The machine switched on the
UKS* function. Because of bad
laundry balance, the machine
has automatically reduced spin
RPM.
The machine operates normally.
Wash large and small pieces of
laundry together.