Smith & Noble Metal Blinds User manual

Step by Step Installation Instructions
Metal Blinds
Customer Service 800.248.8888 or visit us online at smithandnoble.com

1
2
Th a n k y o u for choosing smith+noble. Your new
Metal Blinds have been custom–crafted to your
exact specifications from the highest quality
materials. Once in your windows, they will provide
you with a lifetime of beauty and trouble-free use.
In s T a l l I n g your new blind is easy. Simply follow
our step-by-step instructions. We recommend that
you read through all the instructions before you
start. If you have questions, our customer service
representatives are available at 800.248.8888.
Do not dispose of packaging until the blinds are
operating to your satisfaction.
For assistance, call smith+noble
Customer Service at
800.248.8888
Visit our website at
smithandnoble.com
Contents
Getting Started ................................3
Metal Blinds..................................4
Attaching the Installation Brackets . . . . . . . . . . . . . . . 5
Attaching Hold Down Brackets ..................6
Operating Your Blind ............................6
Troubleshooting ...............................7
Care+Cleaning ...............................8
Safety .......................................8

3
4
Remove the blind from the
packaging.
Do not dispose of packaging
until the blind is operating to
your satisfaction.
Check the diagram to make sure
you have all the parts indicated
for the appropriate type of
installation.
NOTE: Do not lower the blind yet.
Tools you will need to install
your blind: pencil, screwdriver,
1/4" nut driver, level, pliers and a
drill with 1/8" drill bit.
Your brackets must be securely
attached to the mounting
surface. When screwing into a
surface, the included screws
must hit wood studs. Otherwise,
use a secure fastener as
illustrated (not included).
Wallboard Or Plaster:
Use a secure fastener designed
for hollow wall applications.
Metal: Pre-drill holes and use
the included screws.
Concrete, Stone, Brick Or
Tile: Use a masonry drill and
appropriate plugs, anchors or
screws.
When selecting a fastener, make
sure it is designed to support
the weight of the product being
installed. Follow the fastener
manufacturer’s instructions for
proper installation.
Getting Started








Getting Started Parts of your Shade
note: When installing screws with a drill,
be careful not to over-tighten. This may
cause the screw to break off in the wall
or window frame.
Metal Blinds










5
6
Hold Down Brackets + Operating Your Blind
Attaching the Brackets
Attaching the Brackets
Position the first two
installation brackets along the
mounting surface and at each
end of the headrail.
Each bracket should be set 2"
from each end of the headrail.
When using a third or fourth
installation bracket if the width
requires, center it between the
end brackets. Make sure the
brackets will not interfere with
the cord mechanism or any
other internal parts.
Inside Mount
Center the shade in the
window frame. Mark the
bracket for mounting hole
locations, making sure they
are square and equally spaced.
Screw brackets into wall or
window jamb as required.
Outside Mount
Center the blind over the
window opening at the desired
height. Mark the position of
the bracket on the wall. Make
sure the brackets are level.
With the hold-down brackets
attached to the bottom rail,
lower the blind to the hold
down bracket mounting
surface and mark the bracket
locations. Attach the hold
down brackets at the bottom
of the window or door with the
included screws as shown. To
attach the bottom rail, gently
pull the brackets out slightly,
and insert the pins into the
holes on the bottom rail of
the blinds.
Operating Your Blind
To lower the blind, pull the cord down and towards the center of the
shade to unlock the cord. Then, slowly release the cord until the shade
reaches the desired location. Move the cord past the outer edge of the
shade and let go to lock the cord.
To raise the blind, pull the cord straight down until the shade reaches
the desired location. Move the cord past the outer edge of the shade
and let go to lock the cord.
Hold Down Brackets (optional)
BRACKET CHART
Blind WIDTH # OF BRACKETS
Up to 60"2
60 1/8" to 77 3/4"3
77 7/8" and up 4

7
8
Troubleshooting
My Blind Doesn’t Lift:
Check to make sure cord is not
caught in headrail. If hold down
clips were used, make sure they
have been released.
My Blind Will Raise And Lower
But Will Not Tilt:
Check inside the headrail for
obstructions. Make sure all of
the slats are laying properly
on the ladders.
My Blinds Raise Unevenly:
Raise blind to the “up” position,
open the tassel, untie the knots on
the cords, even out the cords, then
re-tie the knots and re-assemble
the tassel.
My Slats Are Hanging
Out Of Alignment:
Lower the blind completely. While
firmly holding the bottom rail,
gently tug on the lift cords until
the slats are even.
One Side Of The Blind
Does Not Raise:
Make sure the lift cords are still
fastened to the bottom rail. If
they are not, please call Customer
Service for assistance.
or
Look inside the headrail to make
sure that cords are not caught on
or under something.
Care and Cleaning
• Clean soiled mini-blind surfaces with a mild soap solution. Do not
steam, hot water, bleach or any abrasive or solvent-based cleaners. Do
not machine wash.
• To ensure proper drying, provide adequate ventilation for blinds,
remove bottom rail plastic end caps, and tip headrail and bottom rail
to drain water.
Safety
All Smith+Noble blinds are made with tassel systems designed to protect
small children and pets if they become tangled in the cords. When the
blind is raised, excess cords may hang within the reach of children or
pets. In these situations, use a cord cleat as shown at right to prevent
possible injury. To obtain a cord cleat call Smith+Noble Customer Service
at 800.780.8889.
cord
cleat
Troubleshooting Care and Cleaning + Safety

9
10
Notes Notes