Snapper 1692210, 1692231, 1692353, 9000100 User manual

INSTALLATION
CHIPPER/SHREDDER VACUUM KIT
INSTRUCTIONS
Mfg. Nos. 1692210, 1692231, 1692353,900OlOO
AWARNING
Turn off the engine, let the rotor come to a
complete stop and disconnect the spark plug
wire before assembling the vacuum kit or
changing attachments.
A WARNING
Never remove% adapter from the back of the
machine while the machine is running or the
rotor is turning. The rotor is pinning just inch-
es away from the adapter iniet. Serious injury
will result if you put your fingers or foot in the
adapter inlet while the rotor is turning!
INSTALLATION
I
Never operate the machine without the cou
pier/hose assembly or plug connected to the
arrows (or seams) running along the top of the cou-
pler with those on the adapter. Push fully in and turn
until it snaps into place.
NOTE:
Insert plug (3) into adapter when vacuum
attachment is not in use. See Removing the
Vacuum Kit on the next page.
4. Slip the grip (12) onto the handle (11). Putting some
soap on the handle will make the grip slide on easi-
er.
1. Remove the rotor housing cover. Retain the screws.
2. Replace the cover with the adapter (1A or 1 B) using
the screws removed in step 1 and washers (15).
3.Twist the coupler (2) onto the end of the hose (4).
Insert the coupler into the adapter hy aligning the
5. Connect the handle to the nozzle (6) using the
screw (lo), washers (9) and nut (8).
6. Connect nozzle (6) or leaf tray (5) to the hose,.
7. Securely place hopper lid (14) on hopper.
Ref. Qty. Part No. Description
1A 1 1021100
Adapter
1B 1 1713522 Adapter (European Model)
2 1 1023100 Coupler
3 1 1025100 Plug
4 1 1035100
Hose, 10’ x 4” Dia.
5 1 1027100 Leaf Tray
6 1 1030100 Nozzle
7
1 1024100 Ring
8 1 1960294
Nut, Hex, Flange, l/4-20
9 1 1921319 Washer, l/4
IO 1 6041612
Screw, Phillups Hd.
1/4-20x I-112
11 1 1026100
Handle
12 1 1028100 Grip, Handle
13 1 5001612
Decal, Danger
14 1 1709404* Hopper Lid (Orange)
1 lOlQlOO* Hopper Lid (Gold)
1 1709467* Hopper Lid (Red)
15 31919326
l Lid color depends on which kit you’ve ordered. Only
one lid is packaged per kit.
Figure 1. Kit Parts
FORM
- 1709566
PRINTED IN U.S.A.
12l93SMI

USING THE VACUUM
The vacuum kit lets you take full advantage of the
vacuum created by the four fan blades on the rotor fly-
wheel. Placing the lid on the hopper directs the suc-
tion power to the hose inlet at the bottom of the hous-
ing.
Use the vacuum kit to conveniently rake dry leaves
and grass clippings into the leaf tray, where the mater-
ial is sucked through the vacuum hose, shredded in
the shredding chamber and expelled out the dis-
charge chute. The hopper lid must be in place for the
vacuum to work properly. The clear vacuum hose
allows you to monitor the flow of material. The vactt-
urn kit works best on dry leaves,
The nozzle and handle can be attached to the end of
the hose for, hard to reach places. The strength of the
vacuum can be adjusted by turning the sleeve on the
nozzle end. Open the sleeve fully for minimum suction
power to vacuum leaves over a garden area.
VACUUMING TIPS
* Keep the hose straight for best performance.
* Rake leaves into the tray at a steady rate so that the
engine or motor runs at an even level. For best
results, do not cram the tray full of leaves.
- Avoid items, such as twigs, that can get caught in
the hose.
* If material is wet, allow to dry before vacuuming.
REMOVING THE VACUUM KIT
1. When not using the vacuum kit, turn off the engine,
let the motor come to a complete, stop and discon-
nect the spark plug wire.
2. Rotate the coupler/hose assembly until the seams
line up on top, pull until it clicks then unscrew and
remove.
3. Insert the plastic plug (3) into the adapter and twist
until it seats completely
FORM
- 1709566