Snapper 1691531 User manual

i ;
KIT PARTS
INSTALLATION., ~-
~~~~~ INSTRUCTIONS
~
ELECTRlC L//=T KIT
MFG. NO. 1691531
For use with a// mounted attachments
~on 6500/1800 Series Tractors
Fi igure 1. Kit Parts
Mount to
Mount to top
capscrew on lift lever
support bracket.
ignition wire.
Used for rear attachments
onlv. Use item Qfor mowers.
FRONT
J
Item
Description Part No.
A Harness Assy.. Elec. Lift 1702082
8 Switch, Electric 171883
C Wire, Switch to Ground 171868
D Lockwasher 1817366
E Power Lift
Assy. 1667764
F Clamp, Insulated 826818
G Connectors, Self-Stripping 1606761
H Wire, Switch to Ignition 1702075
I Wire, Switch to Lift 1702077
J Wire, Switch to Lift 1702076
K Decal, Lift Switch 1669833
L Rod Assy., Lift 1701680
M Arm
Assy.. lift 1701808
my.
1
1
1
4
1
1
1
1
1
1
1
1
1
Item Description
N Pin, Quick
0 Hub Assy.. Wheel
;
P Link, Actuator
QPin, Pivot
R Nut, Hex. 5/16-18
S Bracket, Actuator, Front
1Capscrew, Hex Hd..
5/16-18x 1
u Spacer
” Nut. Hex Lock,
6/16-18
W Capscrew, Hex Hd..
5,‘16-18 x 4-l/2
Part No. oty.
1960033 3
1701914 1
1701881 1 ~
102004 2
1917372 4
1701878 1
1921333 4
1665699 3
1823362 1
1925892
1
FORM 1702100
PR,NTED IN U.S.A.
882
.-
1,

AWARNING
Before installing the kit or making any adjustments:
disengage the PTO; set the parking brake; stop the
engine and remove the key.
AWARNING
When disconnecting the battery cables, always
disconnect the negative cable first. When
connecting cables, always connect the negative
cable last. The positive terminal can easily be
shorted to the frame with
a tool if this is not done.
Do not touch any wires or electrical components
such as the solenoid, unless the battery cables are
INSTALLATION
1. Park tractor on flat, level surface. Turn tractor off.
Disengage PTO, and allow all moving parts to stop.
Engage the parking brake.
,2. Disconnect the battery cables and position away
from terminals.
gasoline may ignite. Insure clamps grip hose firmly
AWARNING
Handle gasoline with care. It is highly flammable.
Use an approved gasoline container.
3. Drain the fuel tank as follows.
a. Place an approved gasoline container below the
fuel filter.
b. Use a pliers to spread the fuel filter clamps and
slide away from filter. Do not spread more than
necessary.
~c. Pull hoses off filter and allow gasoline to drain
into container.
4. Raise rear right-hand side of tractor up and place
jackstand under transaxle.
Remove rear right-hand wheel assembly.
Remove tive capscrews from wheel assembly and
secure kit hub assembly (0, figure 1) to wheel. Do not
install on tractor.
Prepare template (provided on last page) by cutting
out all dashed areas. Use this template to drill five
1
l/32” holes in wrapper.
Install rear actuator bracket (X, figure 1 or A, figure
2) with two capscrews (T, figure l), spacers (U),
lockwashers (D), and nuts (R). Install bolts from
outside in, putting spacers between bracket and
wrapper. Lockwashers and nuts are installed on
inside of wrapper. Do not install the 4-I /2”capscrew
(W) at this time.
9. Install front bracket (C, figure 2) with bottom
capscrew (B) only. Install capscrew from inside out.
,
Secure with lockwasher (D, figure 1) and nut (R).
.-
Figure 2. Bracket Installation
A. Rear Bracket
6. 1” capscrews
C. Front Bracket
10. Insert cylinder (A, figure 3) through brackets as
shown in figure 3.
Makesurelugs(B)fit securely into
rear bracket slots.
11. Install top 4-l /2” capscrew (C) on rear bracket (with
spacer between bracket and wrapper) and secure
with locknut (V, figure I). Install top l”capscrew(D,
figure 3, from inside wrapper) in front bracket and
secure with lockwasher and nut.
-,2.-

Figure 3. Cylinder ~lnstallation
A. Cylinder
6. Lugs
c. 4-l/2” Capscrew
D. 1” Capscrew (from inside out)
12. Remove the manual lift lever as follows:
a. Remove the two capscrews and lockwashen (B,
figure 4). Leave the retaining nuts in place.
b. Remove the lever by removing four
capscrews,
lockwashers and nuts (A). Save the hardware for
reinstallation.
,~~.
.
!
Figure 4. Manual Lift Lever
A. Capscrews, Lockwashers and Nuts
B. Capscrews and Lockwashers
~~c. Remove lift lever bracket support (B, figure 5).
Retain hardware for reinsta%nl
13. Install new electric lift. lever bracket (A) reusing
existing hardware (mounted in same location).
Figure 5. Electric Lift Lever
A. Lift Lever Bracket
S. Bracket Support
c. capscrew
D. Wire Clip
E. Actuator Link
F. Clevis Pin
G. Spring Clip
14.
15.
Reinstall bracket support (B), reusing existing
hardware. In top capscrew (C), install clip (F, figure
I
..~
or D, figure 5). Clip and wiring are shown installed in
figure 5.
Mount actuator link (E) between cylinder and new
lift lever as shown in figure 5. Install clevis pins (F)
from outside and spring clips (G) on inside. When
alignment is correct, tighten all mounting hardware.
NOTE
For rear-mounted attachments, lift rod (L, figure 1)
must be installed. Refer to last section of this
instruction sheet.
SWITCH INSTALLATION
16. A 31/64” hole must be drilled in the lower dash to
mount the switch (see figure 6). Measure two inches
down from upper dash and draw a line. Then,
measure three inches from right side of lower dash
and draw a vertical line. Drill the hole at point where
these two lines meet (figure 6).

20. Remove the upper and lower dash hardware as
follows.
a. Remove the two screws (C, figure 6) and washers.
b. Raise the hood and loosen the two screws, plain :
washers, dished washers and nuts from front side
of dash (see figure 8).
c. Remove four capscrews and washers securing
lower dash.
d. Both dashboards can now be lifted up for access to
wiring.
21. Remove the ignition switch by removing nut. Retain
lockwasher for reinstallation.
22. Reach thru the hole in top of lower dash and install
the switch (A, figure I). Position the switch so that
slot in threads is up. From outside the dash, place the
washers (B) on switch, aligning tab washer in slot in
Figure 6. Tractor Dash threads. Install and tighten the nut securely.
A. Wood Block:
6. Hammer C. Screws 23. Connect black switch wire to white wire from
ignition switch with connector (C, figure 1) provided
) 17., Pry off the throttle control knob by using a claw in kit.
hammer and block of wood as shown in figure 6. ~
lg., Remove throttle cable from left-side engine clamp.
24.) Lift up lower dash and locate taptite screw securing 1~
two black ground wires. Route green wire (C, figure.
Loosen capscrew and washer that secures throttle 1) from switch and ground under this screw.
~cable to intake manifold. Note pinch mark on cable ~
‘, before removing from under capscrew. Cable must ,~ ~~‘~~
25. Route the yellow and red wires from switch down
be reinstalled in same position for correct RPM behind the steering shaft. Wires should follow wiring
‘---
settings. Remove cable from engine. harness and be routed cut lower dash cutout,
19. Remove nut (A, figure 7). flatwashers (B) and underneath shift quadrant panel and thru square,
capscrew (C) securing steering wheel to shaft. Pull hole for seat latch. Refer to figure 5. Wires should
steering wheel off shaft. then be attached to wire clip (D, figure 5).
26. Connect the yellow wire to yellow wire from cylinder.
Connect the red wire to the red wire from cylinder.
27. This completes installation of the kit. Make the :
following test to see if installation is correct.
Figure 7. Steering Wheel
A, 5/16 Locknut
6. l/4 Flat Washers
C. 5116 x 3-l/2 Capscrew
D. Steering Wheel
E. Cap
a. Reinstall ignition switch with lockwasherand nut.
b. Connect the battery cables - negative cable last.
:
c. Turn the ignition switch to ON.
d. Flip the lift switch up, the lift arm should go back.
e. Flip the lift switch down, the lift arm should go
forward.
f. If switch does not check OK, disconnect the
battery cables, Then go thru the instructions and ~
make sure all connections are tight.
g. Reconnect the battery cables to perform above
test again. Before proceeding with following
:
instructions, disconnect the battery cables.
28. Reinstall lower dash with four capscrews and
washers. Position the upper dash over the fuel tank.
Install the original hardware (figure 8).
-4

Figure 8. Upper UaSn
I_
29. Align the steering wheel and push down onto shaft.
30. Reinstall capscrew (C, figure 7), flat washers, and
locknuts to secure steering wheel. Torque nut to 10 ft.
Ibs.
31. Reconnect throttle cable to engine and position
under manifold capscrew and washer. Cable must be
in original position for correct RPM setting. Tighten
capscrew and place cable in left-side engine clamp.
32. Push throttle control knob back on the lever. Tap
knob with a hammer to seat.
33. Make sure the fuel lines are connected securely to the
fuel filter with the clamps.
34. Install the rear right-band wheel assembly.
35. Raise rear of tractor up and rembve jackstand
36. Connect the battery cables - negative cable last.
37. Apply the decal to the right side of the switch.
38. This completes the installation.
I
I
5-.
REAR-MOUNTED ATTACHMENTS -
LIFT ROD INSTALLATION
Lift rod (L, figure 1) is used only for rear mounted
attachments. To install, remove bottom clevis pin (Q)
and install lift rod (A, figure 9) to actuator link(B) and lift
arm (C). Secure with clevis pins (D) as shown.
Figure 9. Lift Rod
A. Lift Rod
6. Actuator Link
C. Lift Arm
D. Spring Clips ~

/
.-. 1
\
! ‘1
./
\\\\\\
I
I\
1
\\
Align with holes In rlght
hand side of axle support;
wrapper -two places
(remove bolts and reinstall
If
necessary).
i
i
II
I
1
I
1
t
\
t
I
I
Al
I
I
\\
:---m ----I
\
f ,’
CUTOU’r (TEMPLATE ONLY)
ON DOTTED LINE.
l
’ Align with holes In rlght
“hand side of axle support
Iwrapper -
two places
I’
(remove bolts and
reinstall If
necessary).
---_
I’
--I’