socomec ATyS d M User manual
l�
un I Jet
,
Модульный автоматический реверсивный рубильник с дистанционным управлением
Socomec ATyS d M - руководство по эксплуатации. Юниджет.
Постоянная ссылка на страницу: https://www.uni-jet.com/catalog/sistemyi-kommutaczii,-
kontrolya-i-zashhityi/pereklyuchateli-nagruzki/socomec-atys-d-m.html
ATySdM
Remotely Operated
Transfer Switching Equipment
EN
INSTRUCTION
MANUAL
www.socomec.com
2EN
www.socomec.com
www.socomec.com/en/atys-d-m
To download, brochures, catalogues and technical manuals :
This manual is available for download in French, English, German, Italian, Spanish, Dutch, Portugese, Russian, Polish, Turkish and Chinese.
3
EN
INDEX
1. GENERAL SAFETY INSTRUCTIONS .......................................................6
2. INTRODUCTION.............................................................................7
2.1. THE ATYS FAMILY PRODUCT RANGE .......................................................7
2.2. THE ATYS M RANGE KEY FEATURES .......................................................8
2.2.1. SELECTION GUIDE ...................................................................9
3. QUICK START ..............................................................................10
..............................................................10
..............................................................12
......................................................................14
................................................................14
......................................................14
...........................................................................14
5. OPTIONAL ACCESSORIES ................................................................15
6. TECHNICAL DATA..........................................................................17
..........................................................18
8. PRODUCT INSTALLATION.................................................................19
8.1. CHANGING THE PADLOCKING CONFIGURATION ...........................................19
8.2. RECOMMANDED ORIENTATION ...........................................................19
8.3. DIMENSIONS OF THE SINGLE PHASE PRODUCT ...........................................19
.........................................19
8.5. DIMENSIONS OF THE THREE PHASE PRODUCT ............................................20
.........................................20
8.7. DIN RAIL MOUNTED ......................................................................20
9. NSTALLATION OF OPTIONAL ACCESSORIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
9.1. AUXILLIARY CONTACTS ..................................................................21
.............................................21
......................................................................21
......................................................................22
9.5. TERMINAL SHROUDS.....................................................................22
.......................................23
10.1. MODULAR PLASTIC ENCLOSURE ........................................................23
EN
..........................................................23
10.2.1. WIRING IN A POLYCARBONATE ENCLOSURE .........................................24
10.2.2. EXTENSION UNIT ..................................................................24
..............................................25
..............................25
.......................25
12. CONNECTION OF CONTROL/COMMAND CIRCUITS...................................26
12.1. TERMINAL CONNECTORS DESIGNATION .................................................27
12.2. AUXILIARY CONTACT OPERATING SCHEDULE ............................................27
13. OPERATION ...............................................................................28
13.1. PRESENTATION OF THE PRODUCT INTERFACE ...........................................28
13.1.1. RESET.............................................................................28
13.2. MANUAL MODE .........................................................................28
13.2.1. MANUAL SWITCHING ...............................................................29
13.3. PADLOCKING ...........................................................................29
..............................................29
............................................................29
13.5.1. SEALABLE AUTO/MANUAL COVER...................................................29
.....................................................................30
13.6.1. CONTROL LOGIC...................................................................30
13.6.2. POSITIONS THAT CAN BE REACHED DEPENDING ON THE AVAILABLE SOURCE .........31
.........................................................32
............................................................33
15.1. FAULT FINDING .........................................................................33
....................................................................33
5
EN
This page intentionally left blank
6EN
1. GENERAL SAFETY INSTRUCTIONS
This manual provides instructions on safety, connections and operation of the ATy
Whether the ATyS is sold as a loose product, as a spare, as an enclosed solution or as any other
personnel, in line with the manufacturers recommendations, following good engineering practices and after
This instruction manual must be made accessible so as to be easily available to anyone who may need to
read it in relation with the ATy
The ATy
yS should be opened (with or without voltage) as there
Do not handle any control or power cables connected to the ATyS when voltage may be present
on the product directly through the mains or indirectly through external circuits.
DANGER WARNING CAUTION
RISK:
Electric shock, burns, death
RISK:
Possible personal injury
RISK:
Equipment damage
7
EN
2. INTRODUCTION
2.1.
Just the right ATyS for your application…
ATyS: Small Footprint
125A - 3200A
ATyS M: Modular Profile
40A - 160A
40A - 125A
(RTSE)
Transformer
RTSE
ATy S
RTSE
Transformer (building)
Side by Side
8EN
2.2. The ATy
Selecting the right ATy
installation in which the ATy
each product to help you select the right ATy
ATyS dM ATyS tM ATyS gM ATyS pM
160 A
40 A
OPEN TRANSITION MOTORISED CHANGEOVER SWITCH
DUAL POWER SUPPLY
BUILT-IN ATS CONTROLLER
COMMUNICATION*
TRIPPING**
* Specific version. ** Return to zero without external energy source.
>
Network / Genset
>
Genset / Genset
>
Network / Network
Applications with an
External ATS Control
>Network / Genset
>
Network / Network
ATyS dM
GS
UPS
>Network / Network
Building applications
ATyS p M
ATyS t M
UPS
ATyS pM
loads
loads
loads
>
Network / Genset
Genset Applications for
Standby Power
UPS
ATyS gM
loads
loads
loads
9
EN
2.2.1. Selection guide
ATyS dM ATyS tM ATyS gM ATyS pM
APPLICATIONS
Normal / Backup without automatic controller •
Normal / Backup with built-in automatic controller • • •
Stable positions • • • •
Load changeover •
FUNCTIONS
POWER SUPPLY
External •
Integrated • • •
OPERATION
Backup manual operation of the 3 positions • • • •
Electrical (dry contact) control of positions I, 0
and II • •*
Automatic control of positions I, 0 and II • • •
Return to 0 position feature upon loss of source •
MONITORING
3 voltages on networks I and II • • •
Frequency on networks I and II • • •
Phase rotation on networks I and II •
Asymmetry of networks I and II •
AUTOMATIC CONTROLLER CONFIGURA-
TION
By potentiometer and micro-switch • •
By screen + keyboard •
Vn, Fn, V threshold, F threshold • • •
Driving with or without priority • • •
Adjustable operating timers • • •
Control type (impulse or switch / contactor) •
DISPLAY
Position, fully visualised breaking • • • •
LED: source status, automatic mode, fault LED • • •
LED: switch positions, supply, tests, control •
V, F, timers, number of operations, last event •
REMOTE CONTROL
Outputs
Generator start / stop order • •
Product availability
(not fault and not manual mode) • •*
Source available • •*
Programmable output (source, availability, fault) •*
Inputs
Test on load • •*
Retransfer • •*
Automatic mode inhibit • • •*
Position O order • •*
Priority • • •
Other programmable inputs
(test off-load, position control, etc.) •*
Remote control
Human / Machine Interface (D10 and D20)
•
RS485 communication (MODBUS) •**
* 3 inputs/3 outputs (programmable).
** Product reference is different: communication by RS485 connection (MODBUS) allows up to 31 ATyS M to be connected to a PC or a PLC over 1500 m.
10 EN
3.
3.1. Quick Start ATy
542 954 C - 12/16 - EN
quick start 40-160A (2P)
EN
ATyS dM
Remotely operated
Transfer Switching Equipment
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
n Packaging and contents are in good condition.
n The product reference corresponds to the order.
n Contents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension rod
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
nThis product must always be installed and commissioned
by qualified and approved personnel.
nMaintenance and servicing operations should be
performed by trained and authorised personnel.
nDo not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
n Always use an appropriate voltage detection device to
confirm the absence of voltage.
n Ensure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
n In case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
n Bridging bars and 125A or 160A.
n Voltage sensine and power supply TAP.
n Terminal shrouds.
n Additionnal aux contact block.
n Plastic enclosure.
n Dual Power Supply (DPS).
n Power Connection Terminals.
n ATS Control relay ATyS C30 + D10 or D20.
n ATS control relay ATyS C20.
n ATS control relay ATyS C40.
Printing informations: 1 color Black. White paper 90g/m2.
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
Non contractual document.
Subject to change without notice.
STEP 1
Cabinet / Back
Plate Installation
STEP 3
CONTROL /
AUX POWER
terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
CHECK
Installation and Commissioning STEP 5A
Automatic Operation
STEP 5C
Padlocking
STEP 5B
Emergency Manual
Operation
www.socomec.com
www.socomec.com/en/atys-d-m
To download, brochures, catalogues and technical manuals.
the ATySM as follows before
movementonthe DINrail.
!
Voltage taps provide 2x ≤ 1.5mm
STEP 4
STEP 3
STEP 5A
Check
Automatic operation
Ensure that the product is in Manual Mode (front cover open).
Whilst in manual mode, check the wiring and
ifok power up theproduct.
Close the front cover as shown to put the product
into automatic mode. The product is now ready to
receive order inputs based on the following logic.
Note: Excludes position switching delays.
For contactor logic bridge
contact 313 with 317.
To operate: close the
contact corresponding to
the desired position.
Auxiliary contacts:
Fitting of the 2nd
To fit an AC, the s
NC changeover contact for each position (I-0-II).
Imp. ≥60ms maintened
order I
position I
order 0
position 0
order II
position II
Contactor logicImpulse logic
STEP 5B
Manual operation
•
Open the front cover as
shown to put into manual
mode.
•
Use the handle situated in
the front panel under the cover to operate the
transfer switch.
•
Check the changeover switch position on the
indicator before operating.
To simplify operation
use the handle with the
extension provided. (Max 8 Nm)
90º 90º
Extension
!
STEP 5C
Padlocking mode
1x 4-8 mm
•
In order to padlock put the
product in manual mode.
•
Pull the locking mecha-
nism and insert a padlock
as shown.
• As standard padlocking in the 0 position.
Configurable to I-0-II (see step 1).
CORPORATE HQ CONTACT:
SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
11
EN
Step 1
Step 2
Step 3
40-160A (2P)
1: Position I order
2: Position II order
3: Position 0 order
4: Power supply I (230 VAC)
5: Power supply II (230 VAC)
6: Voltage tap
7: Auxiliary contact block -
1 NO/NC contact per position I,
0, II (1x factory fitted)
A: Bridging bar (accessory)
B: Single-phase voltage sensing tap
(accessory)
C: F1/F2 = fuse 10 A gG
* Remote orders from ATS
controller such as ATyS C20/
C30/C40 or PLC, BMS, etc.
101102201202313314315317
A
BB
3
4
6 6
2
1C
7
5
LOAD
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 0001
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 0011
Slotted head 3mm 0,5 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
STEP 1
The ATyS M is delivered with
padlocking configured to the
O position.
To allow padlocking in all
positions (I - O - II), configure
the ATySM as follows before
installation. (Screw is located
at the back of the product).
STEP 3
Posidriv PZ2
2,2 lb-in 0,25 Nm
OK
Posidriv PZ2
2
Posidriv PZ2
Posidriv PZ2
Installation Padlocking configuration
Caution: Ensure that the product is installed on a flat rigid surface.
Recommended orientation
Recommended Ok Ok Ok Ok Ok
Posidriv PZ1
1 Nm
Tighten to avoid
movementonthe DINrail.
2x
2x
!
DIN RAIL
IEC 60715
MAX : 2
235
26
116
245
143
350
18
13
222
235
131,5
131,5
47
52 176
224
53
46
73,5
45
4 mounting brackets
4x M6 screw - 2,5 Nm
STEP 2
Power Terminal Connections
Source supply side
Hexagonal Metric
Allen size 4
5,0 Nm
It is essential to tighten all used
terminals, with cables and/or
bridging bars, before use.
Voltage taps provide 2x ≤ 1.5mm2connections.
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
125A: 1309 2006
160A: 1309 2016
Slotted head 3,5 mm
0,45 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
10 to
70 mm²
15mm
STEP 3
CONTROL / AUX POWER
Terminals and wiring
t the product is in Manual Mode (front cover open).
ifok power up theproduct.
y contacts:
One module factory fitted (1309 0001).
itting of the 2nd AC:
1309 0001 or 1309 0011
the switch must first be put in position 0. An auxiliary contact module comprises: one NO/
NC changeover contact for each position (I-0-II). To install use the long screws supplied with the module.
Type Terminal no. Description Characteristics
Recommanded
connection
cross-section
Inputs 101 / 102 Source 1 power supply 220Vac -20% (176Vac) to 240Vac
+20% (288Vac) 45 to 65Hz
0,5 to 2,5 mm²
(rigid)
0,5 to 1,5mm²
(stranded)
201 / 202 Source 2 power supply
313 Position 0 order if closed with 317.
Also allows control logic selection: contactor
(always closed) / impulse (close to switch)
Do not connect to any power supply
314 Position II order if closed with 317
315 Position I order if closed with 317
317 Common control terminal for 313 to 315
Auxiliary
contacts
unit.
11/12/14 Position I Dry potential free contact
250Vac 5A AC1
24Vdc 2A
21/22/24 Position II
01/02/04 Position 0
Control of position I and II have priority on control of position 0.
Imp. ≥60ms
•
•
•
!
Use 35mm
screws for
2 modules
Pozidriv PZ2 - 1 Nm
•
•
•
!X4
Step 1
Step 2
Step 3
12 EN
3.2. Quick Start ATy
the ATySM as follows before
at the back of the product).
movementonthe DINrail.
DIN RAIL
6 mounting brackets
terminals, with cables and/or
bridging bars, before use.
Voltage taps provide 2x ≤ 1.5mm
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
!
542 928 C - 12/16 - EN
quick start 40-160A (4P)
EN
ATyS dM
Remotely Operated
Transfer Switching Equipment
Preliminary operations
Check the following upon delivery and after removal of the
packaging:
n Packaging and contents are in good condition.
n The product reference corresponds to the order.
n Contents should include:
Qty 1 x ATyS M
Qty 1 x Emergency handle extension rod
Qty 1 x Set of terminals
Quick Start instruction sheet
Warning
Risk of electrocution, burns or injury to persons and /
or damage to equipment.
This Quick Start is intended for personnel trained in the
installation and commissioning of this product. For further
details refer to the product instruction manual available on
the SOCOMEC website.
n This product must always be installed and commissioned
by qualified and approved personnel.
n Maintenance and servicing operations should be
performed by trained and authorised personnel.
n Do not handle any control or power cables connected to
the product when voltage may be, or may become present
on the product, directly through the mains or indirectly
through external circuits.
n Always use an appropriate voltage detection device to
confirm the absence of voltage.
n Ensure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
follow these safety instructions may expose the user and
others to serious injury or death.
Risk of damaging the device
n In case the product is dropped or damaged in any way it
is recommended to replace the complete product.
Accessories
n Bridging bars 125A or 160A.
n Control voltage transformer (400Vac -> 230Vac).
n Voltage sensing and power supply tap.
n Terminal shrouds.
n Additionnal aux contact block.
n Polycarbonate enclosure.
n Polycarbonate extension box.
n Dual Power Supply (DPS).
n Power Connection Terminals.
n ATS Control relay ATyS C30 + D10 or D20.
n ATS control relay ATyS C20.
n ATS control relay ATyS C40.
www.socomec.com
www.socomec.com/en/atys-d-m
To download, brochures, catalogues and technical manuals.
Printing informations: 1 color Black. White paper 90g/m2.
Printing size: 420x297. Final size 210x297. This page visible first.
A separate sheet for each language.
Non contractual document.
Subject to change without notice.
STEP 1
Cabinet / Back
Plate Installation
STEP 3
CONTROL /
AUX POWER
terminal
connections
STEP 2
Connecting the
POWER section
STEP 4
CHECK
Installation and Commissioning STEP 5A
Control by an external
order (AUTO)
STEP 5C
Padlocking
STEP 5B
Emergency Manual
Operation
STEP 4
STEP 3
STEP 5A
Check
Automatic operation
Ensure that the product is in Manual Mode (front cover open).
Whilst in manual mode, check the wiring and
ifok power up theproduct.
Close the front cover as shown to put the product
into automatic mode. The product is now ready to
receive order inputs based on the following logic.
Note: Excludes position switching delays.
For contactor logic bridge
contact 313 with 317.
To operate: close the
contact corresponding to
the desired position.
Auxiliary contacts:
Fitting of the 2nd
To fit an AC, the switch must first be put in position 0. An auxiliary contact module comprises:
one NO/NC changeover contact for each position (I-0-II). To install use the long screws supplied
with the module.
101 / 102
201 / 202
(always closed) / impulse (close to switch)
Do not connect to any power supply
11/12/14 Dry potential free contact
21/22/24
01/02/04
Imp. ≥60ms maintened
order I
position I
order 0
position 0
order II
position II
Contactor logicImpulse logic
STEP 5B
Manual operation
•
Open the front cover as
shown to put into manual
mode.
•
Use the handle situated in
the front panel under the cover to operate the
transfer switch.
•
Check the changeover switch position on the
indicator before operating.
To simplify operation
use the handle with the
extension provided. (Max 8 Nm)
90º 90º
Extension
!
STEP 5C
Padlocking mode
1x 4-8 mm
•
In order to padlock put the
product in manual mode.
•
Pull the locking mecha-
nism and insert a padlock
as shown.
• As standard padlocking in the 0 position.
Configurable to I-0-II (see step 1).
CORPORATE HQ CONTACT:
SOCOMEC SAS, 1-4 RUE DE WESTHOUSE, 67235 BENFELD, FRANCE
13
EN
STEP 1
The ATyS M is delivered with
padlocking configured to the
O position.
To allow padlocking in all
positions (I - O - II), configure
the ATySM as follows before
installation. (Screw is located
at the back of the product).
STEP 3
Posidriv PZ2
2,2 lb-in 0,25 Nm
OK
Posidriv PZ2
2
Posidriv PZ2
Posidriv PZ2
Installation Padlocking configuration
Caution: Ensure that the product is installed on a flat rigid surface.
53
46
73,5
45
340
326
131,5
131,5
52 104 176
47
Recommended orientation
Recommended Ok Ok Ok Ok Ok
Posidriv PZ1
1 Nm
Tighten to avoid
movementonthe DINrail.
DIN RAIL
IEC 60715
6 mounting brackets
6x M6 screw - 2,5 Nm
2x
2x
STEP 2
Power Terminal Connections
Source supply side
Hexagonal Metric
Allen size 4
5,0 Nm
It is essential to tighten all used
terminals, with cables and/or
bridging bars, before use.
Hexagonal Metric
"
AWG
10 to 70 mm2
6 to 70 mm 2*
AWG
!X8
Voltage taps provide 2x ≤ 1.5mm2connections.
They can be fitted in any terminals on the source
supply side. Do not use on the load side when
equipped with a bridging bar.
Load side
bridging bar.
125A: 1309 4006
160A: 1309 4016
Slotted head 3,5 mm
0,45 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
10 to
70 mm²
15mm
MAX : 2
340
26
116
245
143
350
18
13
324
!
40-160A (4P)
Risk of electrocution, burns or injury to persons and /
details refer to the product instruction manual available on
the SOCOMEC website.
This product must always be installed and commissioned
by qualified and approved personnel.
Maintenance and servicing operations should be
performed by trained and authorised personnel.
Do not handle any control or power cables connected to
the product when voltage may be, or may become present
confirm the absence of voltage.
Ensure that no metal objects are allowed to fall in the
cabinet (risk of electrical arcing).
Failure to observe good enginering practises as well as to
others to serious injury or death.
Bridging bars 125A or 160A.
Additionnal aux contact block.
Polycarbonate enclosure.
Polycarbonate extension box.
Dual Power Supply (DPS).
ATS Control relay ATyS C30 + D10 or D20.
www.socomec.com/en/atys-d-m
To download, brochures, catalogues and technical manuals.
1 color Black. White paper 90g/m
Printing size: 420x297. Final size 210x297. This page visible first.
Cabinet / Back CONTROL /
Control by an external
STEP 3
CONTROL / AUX POWER
Terminals and wiring
t the product is in Manual Mode (front cover open).
ifok power up theproduct.
receive order inputs based on the following logic.
For contactor logic bridge
y contacts:
One module factory fitted (1309 0001).
itting of the 2nd AC:
1309 0001 or 1309 0011
To fit an AC, the switch must first be put in position 0. An auxiliary contact module comprises:
one NO/NC changeover contact for each position (I-0-II). To install use the long screws supplied
with the module.
1: Position I order
2: Position II order
3: Position 0 order
4: Power supply I (230 VAC)
5: Power supply II (230 VAC)
6: Voltage tap
7: Auxiliary contact block -
1 NO/NC contact per position I,
0, II (1x factory fitted )
A: Bridging bar (accessory)
B: Single-phase voltage sensing tap
(accessory)
C: F1/F2 = fuse 10 A gG
* Remote orders from ATS
controller such as ATyS C20/
C30/C40 or PLC, BMS, etc.
Type Terminal no. Description Characteristics
Recommanded
connection
cross-section
Inputs 101 / 102 Source 1 power supply 220Vac -20% (176Vac) to 240Vac
+20% (288Vac) 45 to 65Hz
0,5 to 2,5 mm²
(rigid)
0,5 to 1,5mm²
(stranded)
201 / 202 Source 2 power supply
313 Position 0 order if closed with 317.
Also allows control logic selection: contactor
(always closed) / impulse (close to switch)
Do not connect to any power supply
314 Position II order if closed with 317
315 Position I order if closed with 317
317 Common control terminal for 313 to 315
Auxiliary
contacts
unit.
11/12/14 Position I Dry potential free contact
250Vac 5A AC1
24Vdc 2A
21/22/24 Position II
01/02/04 Position 0
Control of position I and II have priority on control of position 0.
Imp. ≥60ms
101102201202313314315317
A
BBBB
3
5
4
6 6 6 6
2
1C
7
LOAD
•
•
•
indicator before operating.
Slotted head 3mm 0,5 Nm
0,5 to 2,5 mm²
0,5 to 1,5 mm²
6 mm
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 0001
5 A AC1
250 Vac
22 24 21
11 14 12
01 04 02
1309 0011
!
Use 35mm
screws for
2 modules
Pozidriv PZ2 - 1 Nm
•
•
•
Configurable to I-0-II (see step 1).
Step 1
Step 2
Step 3
EN
4.
4.1.
2
4
3
5
1
2
4
3
5
1
Note: The load may be connected to
the top or bottom of the switch with
tle motorisation preferably on the
right hand side as shown.
4.2.
4.3. Supply types
15
EN
5.
contacts
Ref. : 1309 0001
Ref. : 1309 0011
To provide a common point on the outgoing side of the
Single phase product:
Rating ≤125A : 1309 2006
Rating 160A: 1309 2016
Three phase product:
Rating ≤125A : 1309 4006
Rating 160A: 1309 4016
Voltage sensing
and power
supply tap
voltage sensing
can be mounted in the terminals without reducing their
Ref. : 1399 4006
2 parts/ref.
Terminal
shrouds
Ref. : 2294 4016
2 parts/ref.
Double power
Réf. : 1599 4001
Enclosure
enclosure provides easy access to a compact, enclosed
Ref. : 1309 9006
Ref. : 1309 9007
Single phase
residential
enclosure
Ref. : 1309 9056
16 EN
transformer
neutral connection is available this autotransformer
Ref. : 1599 4121
connection
terminals
The power connection terminals allow conversion of the
Ref. : 1399 4017
For complete conversion,
order 3 times the
reference.
ATS controllers designed for use with products such as
ATyS C30
Supplied from
measurement circuit:
reference 15993030 or
DC power supply:
reference 15993031
ATyS C40
DC power supply: for
Gen/Gen applications:
reference 15993040
Remote control
interfaces
(for use with
Ref. D10 : 1599 2010
Ref. D20 : 1599 2020
17
EN
6. TECHNICAL DATA
Ratings 40A 63 A 80 A 100 A 125 A 160 A
Frequencies
Rated impulse withstand voltage Uimp (kV) (power circuit)
Rated insulation voltage Ui(V) (control circuit)
Rated impulse withstand voltage Uimp (kV) (control circuit)
Rated operational
currents (A)
Rated operational
circuit withstand if using
circuit withstand (kA eff)
(kA eff)
sensing time and
state (VA)
characteristics
Number of changeovers
(not compatible with
aluminium cables)
A A A A A A
This is a class A product. In a domestic environment, this product may cause radio interference in
which case the user may be required to take adequate measures.
18 EN
7.
Temperature
Altitude
UE
Storage
19
EN
8.
For locking in Positions I, II and 0, refer to the following procedure
8.1.
OK
Posidriv PZ2
STEP 2 STEP 3
Posidriv PZ2
2,2 lb-in 0,25 Nm
STEP 1
Posidriv PZ2
2
Posidriv PZ2
2x
2x
!
8.2. Recommanded orientation
Recommended Ok Ok Ok Ok Ok
8.3.
product
8.4. Back plate mounted single
phase product
MAX : 2
235
26
116
245
143
350
18
13
222
53
46
73,5
45
235
131,5
131,5
47
52 176
224
4 mounting brackets
6x M6 screw - 2,5 Nm
Other manuals for ATyS d M
3
This manual suits for next models
36
Table of contents
Other socomec Switch manuals
socomec
socomec STATYS XS 16A User manual
socomec
socomec Sirco MV 100 User manual
socomec
socomec SIRCO MOT AT User manual
socomec
socomec COMO CS 25A User manual
socomec
socomec ATyS 100A User manual
socomec
socomec ATyS FT User manual
socomec
socomec SIRCO 100A User manual
socomec
socomec SIRCO M 16 User manual
socomec
socomec 27003040 User manual
socomec
socomec SIRCO PV User manual
socomec
socomec Sirco MV 100 User manual
socomec
socomec ATyS d M User manual
socomec
socomec 30A User manual
socomec
socomec ATyS UL 1008 User manual
socomec
socomec ATyS Series User manual
socomec
socomec ATyS d H User manual
socomec
socomec Asys 16 A Transfer System User manual
socomec
socomec ATyS t User manual
socomec
socomec Statys XS series Specification sheet
socomec
socomec ATyS g M User manual
Popular Switch manuals by other brands
NVT
NVT NV-8PS42-PVD installation guide
Swegon
Swegon ELQZ-4-613-0 Installation
Ubiquiti
Ubiquiti USW-Industrial quick start guide
Cambridge Research Systems
Cambridge Research Systems BOLDscreen 32 AVI Getting started
SMC Networks
SMC Networks TigerSwitch SMC8708L2 Technical specifications
Agilent Technologies
Agilent Technologies 75000 Series C Service manual
