Solahart ET Series User manual

Solahart PV and battery systems must be installed and serviced by a suitably qualified person.
Please leave this guide with the system owner.
Owner’s Guide
Goodwe Energy Storage Systems
ET and GEH Series Inverter &
Lynx Home F-Series Battery

PATENTS
This battery system may be protected by one or more patents or registered designs in the name of
Solahart Industries Pty Ltd.
TRADE MARKS
®Registered trademark of Solahart Industries Pty Ltd.
™ Trademark of Solahart Industries Pty Ltd.
Note: Every care has been taken to ensure accuracy in preparation of this publication.
No liability can be accepted for any consequences, which may arise as a result of its application.
Warning:For continued safety of this Battery system it must be installed, operated and maintained
in accordance with these instructions and the installation guides supplied with the Battery, Inverter
and Battery Interface.
Warning:Only suitably qualified and accredited personnel should perform work on PV and/or
Battery systems, such as design, installation, commissioning, maintenance and repairs. Be sure to
follow the safety instructions for all system components. It is also important to observe relevant
local codes and regulations for health and safety and accident prevention.
Only Solahart parts and Solahart approved parts may be used. No substitute parts may be used without
prior approval from Solahart Industries Pty Ltd. Only parts supplied by Solahart Industries Pty Ltd are
covered by the Solahart warranty.
The warranty can become void if safety devices are tampered with or if the installation is not in
accordance with these instructions.

3
CONTENTS
Contents ....................................................................................................................................... 3
Important Safety Instructions .................................................................................................... 4
About Your Battery System........................................................................................................ 5
Operating Procedures................................................................................................................. 7
Inverter Status ............................................................................................................................. 9
BATTERY Status........................................................................................................................ 11
Electrical Safety......................................................................................................................... 14
Maintenance............................................................................................................................... 14
Solahart PV System and/or battery Warranty - Australia Only............................................. 15

4
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE IMPORTANT SAFETY INSTRUCTIONS
During installation, testing and inspection, adherence to all the safety instructions is mandatory.
SAFETY SYMBOLS
The following symbols are used in this document to highlight important information:
Warning: Warning indicates a potentially hazardous situation which, if not avoided, could result
in death or serious injury.
Caution: Caution indicates potentially hazardous situation which, if not avoided, could result in
minor or moderate injury and damage to or destruction of the product.
Note: Note indicates additional information intended to assist in the understanding of the
text or an important step that leads to optimal results but is not safety or damage
related.
GENERAL SAFETY INFORMATION
Warning:Adhere to the instructions in this document in addition to each system component
installation guide. Failure to follow any instructions or warnings in the supplied documentation can
result in electric shock, serious injury, or death.
Warning:Only qualified personnel should perform work on photovoltaic and Battery systems.
Warning:A Battery can present a risk of electrical shock, fire, or explosion from vented gases.
Observe proper precautions.
Warning:Ensure electrical connection / disconnection is performed only when the relevant circuit
is isolated. Do not connect / disconnect wiring under load conditions.
Warning:Do not attempt to disassemble, repair, tamper with, or modify any system component.
Warning:Do not expose any component to direct flame or heat sources.
Warning: Do not install any component that is defective, appears cracked, broken, or otherwise
damaged.
Warning: Do not install the system in potentially hazardous locations.
Warning: Do not immerse any component in water or other liquids.
Caution: Ensure clearances are maintained around the Battery and System Components. Remove
debris and other foreign objects from within the clearances areas.
Caution: Do not place any items on top of the Battery BCU.
Caution: Only Solahart supplied / approved components may be used.
Caution: Keep the Battery and Inverter system turned ON at all times. Do not turn OFF the system
when leaving the home for an extended period of time.
ACTIONS TO UNDERTAKE IN THE EVENT OF AN EARTH FAULT ALARM OR TRIPPED AC/DC CIRCUIT
BREAKER
Limit access to all parts of the PV and Battery system.
Contact Solahart Service on 1800 638 011 or your nearest Solahart dealer.

5
ABOUT YOUR BATTERY SYSTEM
INTRODUCTION
This Owner’s Guide applies to the GoodWe ET and GEH-Series Inverter, Goodwe Lynx Home F-Series Battery
and balance of system components. For more information regarding the specific operation of a PV system,
refer to “Owners Guide - Solahart” for PV systems.
SYSTEM OVERVIEW A – COMPLETE PV AND BATTERY WITH BACKUP SYSTEM
Figure 1 System Overview – Complete PV and Battery With Backup System
The Solahart Complete PV and Battery system consists of the following components:
•PV array – generates direct current (DC) power through the conversion of light energy from
the sun.
•Goodwe ET and GEH Series Inverter – inverts the DC power generated from the PV array or
supplied from the Goodwe Lynx U-Series Battery into alternating current (AC) power so it can
be used in the home or exported to the grid. If configured, the inverter can also supply power
to selected backed up loads during grid interruptions.
Note: Both the Inverter and house electrical wiring will need to be configured for backup
functionality to operate. Your Solahart dealer will demonstrate and explain the operation of
this configuration.
Note: A minimum Battery energy level (depth of discharge) can be reserved in case of a grid
outage or just during normal operation. Discuss your requirements with the Solahart dealer to
ensure the system is set correctly.
•Goodwe Lynx F-Series Battery – stores DC power generated by the PV array so the power
can be used when the sun is not shining.
•PV Array DC Isolators – provides a means for isolating the PV array.
•Battery DC Isolator – provides a means of isolating the Battery.
•Inverter AC Isolator – provides overcurrent protection of the inverter and a method of isolating
the PV System from the electrical distribution grid.
•Inverter Backup Load AC Isolator –provides a means of disconnecting the inverter from the
backup loads (if applicable).
Note: It is optional to install an AC grid bypass switch on the Backup Circuit. Please confirm
with the installer.
•Smart Meter – measures net electrical power to and from the grid.
For more information regarding the specific operation of a PV system, refer to the Solahart Owner’s Guide –
PV systems.

ABOUT YOUR BATTERY SYSTEM
6
BASIC SYSTEM OPERATION
The Solahart Complete and Retrofit systems increase energy independence by using the battery to store
excess PV energy, which would otherwise be exported to the grid, so it can be used when required.
The Solahart Complete and Retrofit systems are programmed to maximise savings by minimising the power
purchased from the grid. If the power delivered by the PV and Battery is insufficient to meet domestic demands,
the power necessary to ensure the normal operation of the connected devices is drawn from the grid.
If the energy generated exceeds that required by property demands and the storage capacity of the Battery,
your electrical network operator may allow the difference to be directly injected into the grid and become
available to other users. Energy injected into the grid can be measured by electricity network operators as
either gross (everything generated) or net (excess generated). Injected energy may or may not be purchased
by the local electrical network operator according to national and local standards, and regulations.
Warning: Do not overload the backup circuit beyond the system specifications.
Warning: In the event any circuit breakers continue to trip, please contact your Solahart Dealer
Warning: Do not switch the battery off for extended period of time. It might cause damage.
Caution: If a backup changeover switch is not installed and the inverter is not operating, the loads
and appliances on the backup circuit will not be supplied power.
Caution: Ensure that the backup reserve limit of the battery system is adjusted to an appropriate
setting to provide backup power when the grid out. This can be set within the system monitoring
portal.
INVERTER BACKUP CAPACITY
Inverter Model
Max. Backup
Continuous
Power Output
Peak Backup Power
Output
Backup Max. AC
Output Current
GW5kL-ET
5.0 kVA
10.0 kVA(60 seconds)
8.5 A
GW10KL-ET
10.0 kVA
16.5 kVA(60 seconds)
16.5 A
GW15K-ET
15.0 kVA
24.0 kVA(3 seconds)
22.7 A
GW20K-ET
20.0 kVA
32.0 kVA(3 seconds)
30.3 A
GW25K-ET
25.0 kVA
30.0 kVA(60 seconds)
37.9 A
GW29.9K-ET
29.9 kVA
36.0 kVA(60 seconds)
45.5 A
GEH8.6-1U-10
5.0 kVA
10.32 kVA(60 seconds)
39 A
GEH10-1U-10
9500(@220Vac)
10000(@230Vac)
12 kVA(60 seconds)
43.5 A
Note: If the load on backup circuits exceed the inverter backup capacity, the inverter will shut down temporarily
to protect itself.
•During normal operation, the inverter will restart after 60s.
•During grid outage, the inverter will restart once grid is re-connected.
BATTERY CAPACITY
Battery Model
Rated
Capacity
Usable
Capacity
Max. Discharge
Power
LX F6.6-H (x2)
6.55 kWh
6.6 kWh
6.1 kW
LX F9.8-H (x3)
9.83 kWh
9.83 kWh
9.2 kW
LX F13.1-H (x4)
13.10 kWh
13.10 kWh
12.2 kW
LX F16.4-H (x5)
16.38 kWh
16.40 kWh
15.3 kW

7
OPERATING PROCEDURES
CHECK BEFORE POWER ON
Check the following items before power on to avoid the battery system being damaged.
POWER ON THE BATTERY SYSTEM
Single Battery System
Turn on the breaker between the inverter and the battery system. Turn on the air switch of the battery
system. Turn on the inverter in the system following the instructions in the user manual of the inverter.
Parallel Connected Battery System
1. Turn on the breaker between the inverter and the battery system.
2. Turn on the breakers between the battery systems.
3. Turn on the air switch of the battery systems in turn.

8
4. Turn on the inverter in the system following the instructions in the user manual of the inverter.
POWER OFF THE BATTERY SYSTEM
Follow the steps below to power off the battery system to prevent the system from being damaged.
Method one:
1. Turn OFF the inverter in the system following the instructions in the user manual of the inverter.
2. Long press the multifunction button indicator for more than 15s, and make sure that the SOC indicator
and multifunction button indicator of the PCU are off.
Method two:
1. Turn OFF the inverter in the system following the instructions in the user manual of the inverter.
2. Disconnect the air switch, and make sure that the SCO indicator and multifunction button indicator of the
PCU are off
Danger:Power off the battery system before operations and maintenance. Otherwise, the
equipment may be damaged or electric shocks may occur.
Push the air switch to restart the battery..
Warning:Depending upon the system there may be more than one PV Array DC Isolator.
Warning:To effectively isolate the wiring between the AC Isolator and switchboard, the Solar
Supply Main Switch located in the switchboard must also be in the OFF position.
Warning:PV Array DC Isolators do not de-energise the PV array and array cabling.
Caution: If the Solahart Battery system is expected to be OFF for longer than one month, refer to
the instructions supplied with the Battery.

9
INVERTER STATUS
The GEH Series inverter status is indicated by several LEDs, please refer to the following table for details.
Note: Refer to GoodWe GEH Series inverter user manuals for simple troubleshooting procudures.
Note: If the Inverter LED Status indicates a FAULT, contact your nearest Solahart Dealer.

10
The ET Series inverter status is indicated by several LEDs, please refer to the following table for details.
Note: Refer to GoodWe ET Series inverter user manuals for simple troubleshooting procudures.
Note: If the Inverter LED Status indicates a FAULT, contact your nearest Solahart Dealer.

11
BATTERY STATUS
The battery status is indicated by several LEDs, please refer to the following table for details.

12

13
Note: Refer to GoodWe Lynx F Series battery user manuals for simple troubleshooting procudures.
Note: If the Battery LED Status indicates a FAULT, contact your nearest Solahart Dealer.

14
ELECTRICAL SAFETY
SAFETY REQUIREMENTS
The voltages and currents produced by the Inverter & Battery system can be dangerous. Do not tamper with
system cabling under any circumstances.
UNIQUE HAZARDS OF DC ELECTRICITY
Batteries typically operate using DC electricity. Once the current is flowing, breaking or opening a connection
(e.g. disconnecting a DC cable from the Inverter) can cause a DC electrical arc. Unlike arcs occurring in
conventional low voltage AC wiring, DC arcs are not self-extinguishing. They are a potentially lethal burn and
fire hazard, capable of creating high temperatures that can destroy contacts and connectors.
EARTH FAULTS
An earth fault is a system fault where a short circuit is formed between the DC circuitry of the PV and Battery
system and earth. As the system owner, please be aware of the method of communication of earth faults on
your system. Refer to Earth Fault Alarms in the Solahart Owner’s Guide for PV systems.
MAINTENANCE
GENERAL
The Solahart Inverter & Battery system has been designed for minimal and easy maintenance.
Note: Ensure that you have monitoring access to your Inverter & Battery System. If you do not, contact your
nearest Solahart Dealer.
For recommended maintenance of the PV system, refer to the Solahart Owner’s Guide for PV systems.
RECOMMENDED MAINTENANCE SCHEDULE

15
SOLAHART PV SYSTEM AND/OR BATTERY WARRANTY -
AUSTRALIA ONLY
IMPORTANT NOTE: This Limited Warranty covers a range of systems, products and
components. This Warranty only applies in respect of the specific items you have purchased
and which are delivered to you in conjunction with this hard copy Warranty document.
Your new PV System comprises a PV Module, an Inverter, a racking system and balance of system
components (together the PV System). Alternatively, you may add components sourced from Solahart to your
existing PV System, including a battery and associated products.
The PV System, the Battery, and any other components supplied by Solahart (collectively, the ‘Products’) are
covered by this warranty given by Solahart Industries Pty Ltd ABN 45 064 945 848 of 1 Alan Street, Rydalmere
NSW 2116 (Solahart). The terms of your warranty are set out below. This warranty consists of a number of
parts (not all of which will apply, depending on the Products you have purchased):
A. The specific warranty terms for Modules supplied by Solahart;
B. The specific warranty terms for the LG Chem, Tesla, GoodWe, SolarEdge and BYD Batteries;
C. The specific warranty terms for Inverters and EV chargers – FIMER/ABB;
D. The specific warranty terms for SolarEdge Inverters and associated SolarEdge products;
E. The specific warranty terms for GoodWe Inverters and associated GoodWe products;
F. The specific warranty terms for Solahart Gateway and Energy Management products;
G. The specific warranty terms for the racking system;
H. The specific warranty terms for the balance of the system;
I. The specific warranty terms for the labour; and
J. General terms which apply to all of the above.
This Limited Warranty is valid in Australia for all Products sold after 1 June 2022. If a subsequent version of
this warranty is published, the terms of that warranty will apply to Products manufactured after the date
specified in the subsequent version.
Solahart issues the following voluntary warranty to:
3. The end-user who purchased the System in Australia for their own use and put the System into use for
the first time (the ‘Original End-User’); and
4. In the case of the SolarEdge Energy Bank, SolarEdge Products, GoodWe Products and the BYD Battery-
Box System only, any owner of the product subsequent to the Original End-User who provides proof of
title transfer, provided that the product has never been relocated from its original installation location, or
de-installed and re-installed, without the express written consent of Solahart.
This warranty is in addition to any rights and remedies that you may have under the Australian Consumer Law.
Solahart offers national service through its Dealer network. Solahart will repair or replace parts subject to the
terms of this Limited Warranty. Solahart, in addition can provide preventative maintenance and advice on the
operation of the PV System. You can contact Solahart on 1800 638 011 to arrange a service call or to find out
details about this warranty.
Notification of a claim under this Limited Warranty must be given without undue delay after detection of the
defect and prior to the expiration of the applicable Warranty Period and in accordance with the procedure set
out below.

16
PART A - MODULES
Defects warranty coverage for Solahart Modules
Subject to the terms of this Limited Warranty, Solahart warrants that the Solahart Modules will not show any
material defects or processing defects for a period of:
- for SolahartxxxV1, SolahartxxxV2 and SolahartxxxC1 range modules, 15 years after the date of
initial purchase of the Module (being the invoice date);
- for SolahartxxxS2, SolahartxxxS3 and SolahartxxxS4 range modules, 25 years after the date of
initial purchase of the Module (being the invoice date);
if used and serviced in accordance with the relevant Module specifications and other product documents (the
‘Module Warranty Period’).
If a defect (as described above) occurs during the Module Warranty Period materially affecting the functionality
of the Module, Solahart will, at its sole option:
1. Remedy the defect;
2. Supply a replacement Module free of defects; or
3. Repay the purchase price of the Module.
Module Defects Warranty Terms, Limitations and Exclusions
This limited warranty applies to a Module if used, serviced and maintained in accordance with the Solahart
Owner’s Guide which accompanies the Module.
This warranty does not apply to scratches, marks, mechanical wear, rust, mould, degradation, discoloration,
stains, and other changes which occur after the delivery of the Modules but which do not result in any adverse
effect on the mechanical stability of the Module or a reduction of performance which exceeds the levels set
out in this warranty.
Solahart will pay the costs of a technical inspection and transport of defective or non-performing Modules to
its nominated location. If the Module is found by Solahart not to be defective (including for any of the exclusions
outlined in this warranty document), you agree to reimburse us for those costs on demand. All dismantling and
reinstallation costs are your sole responsibility.
In the event of glass breakage, Solahart will also perform a static calculation to verify the substructure before
accepting liability under this warranty.
To make a claim in relation to that module product warrantee, please contact your local Solahart dealer on
1800 638 011 for assistance with your claim with the source manufacturer. Warranty claims contact for
manufacturer – [e-mail]
Performance guarantee
A performance guarantee (as described in the relevant datasheet) is offered on each PV module by the source
manufacturer, as identified on the relevant datasheet.
To make a claim in relation to that module performance guarantee, please contact your local Solahart dealer
on 1800 638 011 for assistance with your claim with the source manufacturer. Warranty claims contact for
manufacturer – [e-mail]
PART B – BATTERIES
Warranty coverage for capacity retention – LG Chem Battery
Subject to the terms of this Limited Warranty, Solahart warrants that the LG Chem Battery will retain the
capacity levels specified in Exhibit A during the applicable periods identified in the Exhibit (each, an ‘LG Chem
Capacity Retention Warranty Period’).
Remedies – LG Chem Battery

17
If Solahart determines that a reported defect in relation to a LG Chem Battery is eligible for coverage under
this Limited Warranty, Solahart will, at its sole option:
1. Repair the defective LG Chem Battery;
2. Replace the LG Chem Battery; or
3. Provide a Refund to be calculated in accordance with the formula below.
100% of the purchase price from the initial installation date to 24th month
72% of the purchase price from 25th to 36th month
58% of the purchase price from 37th to 48th month
44% of the purchase price from 49th to 60th month
30% of the purchase price from 61st to 72nd month
16% of the purchase price from 73rd to 84th month
6% of the purchase price from 85th to 96th month
4% of the purchase price from 97th to 108th month
2% of the purchase price from 109th to 120th month
Warranty coverage - Tesla Powerwall Battery
Subject to the terms of this Limited Warranty, Solahart warrants that the Tesla Powerwall Battery will be free
from defects for 10 years following its initial installation (‘Tesla Warranty Period’).
Remedies – Tesla Powerwall Battery
If your Tesla Powerwall Battery fails to comply with the above warranty during the Tesla Warranty Period,
Solahart will, at its sole option:
1. Repair your Tesla Powerwall Battery;
2. Replace your Tesla Powerwall Battery with an equivalent product; or
3. Refund you the market price of an equivalent product at the time of the warrant claim.
Warranty coverage - GoodWe Batteries
Subject to the terms of this Limited Warranty, Solahart warrants that the GoodWe Battery will be free from
defects for 10 years following its initial installation (‘GoodWe Warranty Period’).
Remedies – GoodWe Battery
If your GoodWe Battery fails to comply with the above warranty during the GoodWe Warranty Period, Solahart
will, at its sole option:
4. Repair your GoodWe Battery;
5. Replace your GoodWe Battery with an equivalent product; or
6. Refund you the market price of an equivalent product at the time of the warrant claim.
Warranty coverage for defects - SolarEdge Energy Bank
Subject to the terms of this Limited Warranty, Solahart warrants that the SolarEdge Energy Bank will be free
from defects in workmanship and materials for 10 years from the SolarEdge Energy Bank’s installation date,
as recorded by the SolarEdge Monitoring Portal; (‘Solahart Warranty Period’).
Warranty coverage for capacity retention – SolarEdge Energy Bank
Subject to the terms of this Limited Warranty, Solahart warrants that the SolarEdge Energy Bank will have an
energy capacity as follows (‘Energy Capacity’):

18
Configuration
Energy Retention
Energy Throughput
SolarEdge Energy Bank
70% at the end of the Solahart
Warranty Period
Unlimited cycles
SolarEdge Energy Bank Warranty Terms and Exclusions
This warranty for the SolarEdge Energy Bank applies if the SolarEdge Energy Bank is:
1. Used in accordance with its intended purpose and installed and used in compliance with applicable laws
and regulations;
2. Connected to an approved SolarEdge Inverter and the SolarEdge Monitoring Platform for the entire
duration of the Warranty Period;
3. Used solely for standard solar use in one of the following modes: solar self-consumption, time of use,
backup applications or Solahart-managed Energy Management or Grid Services;
4. Used, installed, and handled in accordance with the provisions of the Solahart Energy Bank Data Sheet
and the SolarEdge Energy Bank Installation Manual available on the SolarEdge website (‘SolarEdge
Documentation’);
5. Installed in a location where the ambient temperature falls between 0°C to 40°C for no less than 95% of
the SolarEdge Warranty Period.
The manufacturer requires the ability, without prior notice, to update the SolarEdge Energy Bank through
remote firmware upgrades from time to time, which may temporarily interrupt the operation of the SolarEdge
Energy Bank. If the SolarEdge Energy Bank is not connected to the SolarEdge Monitoring Portal, these
upgrades will not be able to be made and Solahart will not be able to honour these warranties for the SolarEdge
Energy Bank.
Remedies for SolarEdge Energy Bank
If your SolarEdge Energy Bank fails to comply with the above warranties during the Solahart Warranty Period,
Solahart will at its sole option:
1. Repair the SolarEdge Energy Bank;
2. Replace the SolarEdge Energy Bank with an equivalent product at the time of the warranty claim; or
3. Issue a credit note for the defective product in an amount up to the actual value of the lost SolarEdge
Energy Bank’s capacity at the time the owner notifies Solahart of the defect, as determined by Solahart,
for use toward the purchase of new product.
Warranty coverage for defects - BYD Battery-Box System
Subject to the terms of this Limited Warranty, Solahart warrants that the BYD Battery-Box System will be free
from defects in materials or workmanship for 10 years from the sales date as mentioned in the seller’s invoice
(‘Warranty Start Date’) to the Original End-User (‘BYD Warranty Period’).
Warranty coverage for capacity retention – BYD Battery-Box System
Subject to the terms of this Limited Warranty, Solahart warrants that the BYD Battery-Box System HVM series
will: (i) retain sixty per cent (60%) of its Usable Energy (as specified in Exhibit B) for ten (10) years from the
Warranty Start Date; or (ii) reach the Minimum Throughput Energy (as specified in Exhibit B), whichever
comes first, on the condition that the Product is operated under normal use in accordance with Solahart
Owner’s Manual, (the ‘Minimum Throughput Energy’ is the total output energy of the Product recorded in the
control module of the Product) (each a ‘BYD Warranty Period’).
Warranty coverage for capacity retention for additional battery modules after the initial installation
(Subsequent Product) – BYD Battery-Box System
Subject to the terms of this Limited Warranty, Solahart warrants that the Subsequent Product will: (i) retain
sixty percent (60%) of Usable Energy (as specified in Exhibit B) for ten (10) years from the invoice date of the
Subsequent Product; or (ii) reach the Minimum Throughput Energy (as specified in Exhibit B), whichever
comes first, on the condition that the Product is operated under normal use in accordance with Solahart
Owner’s Manual (‘BYD Warranty Period’).

19
BYD Battery-Box System HVM series Warranty Terms and Exclusions
This warranty for Battery-Box System HVM series does not apply:
1. If access is not granted to the performance data of the Product over the Internet upon request after
reporting the warranty claim or
2. To wear and tear in the appearance of the Product (including to any scratches, stains, mechanical wear,
rust or mould) which does not impair its function.
Remedies for BYD Battery-Box System HVM series
If your BYD Battery-Box System fails to comply with the above warranties during the relevant BYD Warranty
Period, Solahart will repair or replace the non-conforming Product or parts at no charge (or provide a partial
refund) on the following conditions:
3. Whether to repair or replace the Product will be determined by Solahart in its sole discretion.
4. If the manufacture of the BYD Battery-Box System in issue has been discontinued at the time of the
warranty claim, withdrawn from the market, or are otherwise unavailable Solahart may, at its discretion,
replace it with a similar Product or part (which may include previously used parts that are equivalent to
new in performance and reliability).
5. If Solahart does not repair or replace the defective Product or parts, Solahart will refund an amount of
money calculated as follows:
i. If the Product cannot be operated (that is, the warranty for defects applies), the refund will be
calculated as follows:
Refund = (Maximum Claim Amount*/120) × (120 - number of months since Warranty Start Date);
ii. If the Product fails to comply with the Limited Performance Warranty for capacity, Solahart may
calculate the refund using one of the two refund formulas below:
i) Refund = Maximum Claim Amount * × (warranted Minimum Throughput Energy - output energy
of the Product recorded in the control module of the Product)/ warranted Minimum
Throughput Energy; or
ii) Refund = Maximum Claim Amount * × (warranted remaining Useable Energy - remaining
Useable Energy)/ warranted Usable Energy;
Where:
- * the Maximum Claim Amount is the market value of the Product (or an equivalent Product)
determined by Solahart if it were purchased new with no defects; and
- the Minimum Throughput Energy and the Usable Energy are specified in Exhibit B.
PART C – INVERTERS AND EV CHARGERS –FIMER/ABB
Warranty coverage for FIMER/ABB Inverters
Solahart warrants that a FIMER/ABB Inverter when provided by Solahart or a Solahart certified installer, when
located at its original installation, will operate in accordance with its specifications in the Solahart's Owner’s
Guide and Installation Instructions for a period of: (a) ten (10) years from the date of purchase of the inverter
for all UNO-DM Inverters; and (b) five (5) years from the date of purchase of the inverter for all other
FIMER/ABB Inverters. If the Inverter fails to operate in accordance with its specifications and this materially
affects the usability of the Inverter, Solahart will, at its sole option:
1. Repair the Inverter (either on site or at FIMER/ABB’s factory); or
2. Provide a replacement Inverter (which might be new, reconditioned or an equivalent product).
3. Reimbursement.
Warranty coverage for FIMER EV Chargers
Solahart warrants that a FIMER EV Chargers when provided by Solahart or a Solahart certified installer, when
located at its original installation, will operate in accordance with its specifications in the Solahart's Owner’s

20
Guide and Installation Instructions for a period of: (a) two (2) years from the date of purchase of the EV Charger
for all Fimer EV chargers; and (b) two (2) years from the date of purchase of the EV Charger for all other
FIMER EV Chargers. If the EV Charger fails to operate in accordance with its specifications and this materially
affects the usability of the EV Charger, Solahart will, at its sole option:
4. Repair the EV Charger (either on site or at FIMERs factory); or
5. Provide a replacement EV Charger (which might be new, reconditioned or an equivalent product).
6. Reimbursement.
Warranty Terms
If Solahart determines in its sole discretion that you do not have a valid warranty claim, Solahart may invoice
you for any inspection and transportation costs of the returned Product.
Given the evolution of the technology, a replacement unit or a new device available at the time of the claim
may not be compatible with the installed system. The warranty does not cover any expenses and/or costs
incurred as part of the configuration, update or adjustment of the system to enable the installation of the
Product. Solahart will not be liable under this warranty to pay any financial compensation, including
compensation for any energy not supplied to the network by the system during any assistance activities,
including preventive and corrective maintenance.
PART D – INVERTERS AND ASSOCIATED COMPONENTS – SOLAREDGE
(In this Part D, a reference to “Products” is to the SolarEdge Products as described below).
Warranty coverage for SolarEdge Inverter
Subject to the terms of this Limited Warranty, Solahart provides a warranty against defects in workmanship
and materials in relation to the SolarEdge Inverter, when located at its original installation, for a period of twelve
(12) years commencing on the earlier of:
7. 4 months from the date the Inverter is shipped from the manufacturer; and
8. The date of installation of the Inverter.
Warranty coverage for StorEdge Interface
Subject to the terms of this Limited Warranty, Solahart provides a warranty against defects in workmanship
and materials in relation to the StorEdge Interface for a period of ten (10) years commencing on the earlier of:
1. 4 months from the date the Interface is shipped from the manufacturer; and
2. The date of installation of the Interface.
Warranty coverage for Power Optimizers
Subject to the terms of this Limited Warranty, Solahart provides a warranty against defects in workmanship
and materials in relation to the Power Optimizers for a period of twelve (12) years commencing on the earlier
of:
1. 4 months from the date the Power Optimizers are shipped from the manufacturer; and
2. The date of installation of the Power Optimizers.
For all Power Optimizers with a part number ending in C, this warranty does not apply to the input connector.
Warranty coverage for Power Meter
Subject to the terms of this Limited Warranty, Solahart provides a warranty against defects in workmanship
and materials in relation to the Power Meter for a period of five (5) years commencing on the earlier of:
1. 4 months from the date the Power Meter is shipped from the manufacturer; and
2. The date of installation of the Power Meter.
Remedies
If Solahart determines that a reported defect in relation to a Product is eligible for coverage under this Limited
Warranty (including retention capacity), Solahart will, at its sole option:
1. Repair the defective Product;