Sole Fitness B94 User manual

B94/R92 FITNESS BIKE OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE OPERATING YOUR NEW FITNESS BIKE

TABLE OF CONTENTS
1
2
3
3
5
11
15
16
19
24
26
27
ATTENTION
THIS FITNESS BIKE IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR
THE APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY.
Product Registration
Important Safety Instructions
Important Electrical Information
Important Operation Instructions
B94 Assembly Instructions
R92 Assembly Instructions
Fitness Bike Features
Operation of Your New Fitness Bike
Programmable Features
Using Heart Rate Monitor
General Maintenance
Manufacturer’s Limited Warranty

B94 / R92 FITNESS BIKE1
Thank you for your purchase of this quality tness bike from SOLE. Your new tness bike has been
manufactured by one of the leading tness manufacturers in the world and is backed by one of the
most comprehensive warranties available. SOLE will do all we can to make your ownership
experience as pleasant as possible for many years to come.
If you have any questions about your new product or questions about the warranty contact SOLE
Fitness at 1-866-780-SOLE (7653). If you have a technical problem with your new tness bike
contact SOLE technical service at 866-MYSOLE1 (697-6531).
Please take a moment at this time to record below the name of the dealer, their telephone number,
and the date of purchase for easy contact in the future. We appreciate your condence in SOLE and
we will always remember that you are the reason that we are in business. Please complete and mail
your registration card today and enjoy your new tness bike.
Yours in Health,
SOLE Fitness
CONGRATULATIONS ON YOUR NEW FITNESS BIKE AND WELCOME TO THE SOLE FAMILY!
RECORD YOUR SERIAL NUMBER
Please record the Serial Number of this tness product
in the space provided below.
Serial Number
REGISTER YOUR PURCHASE
The self-addressed product registration card must be completed in full and returned to SOLE.
You can also go to www.soletreadmills.com under the support tab to register online.
Name of Dealer
Telephone Number of Dealer
Purchase Date
PRODUCT REGISTRATION
B94_R92_20110101

2B94 / R92 FITNESS BIKE
WARNING - Read all instructions before using this appliance.
Do not operate tness bike on deeply padded, plush or shag carpet. Damage to both carpet
and tness bike may result.
Keep children away from the tness bike. There are obvious pinch points and other caution
areas that can cause harm.
Keep hands away from all moving parts.
Never operate the tness bike if it has a damaged cord or plug. If the tness bike is not work-
ing properly, call your dealer.
Keep the cord away from heated surfaces.
Never drop or insert any object into any openings.
Do not use outdoors.
To disconnect, turn all controls to the o position, remove tether cord, then remove the plug
from the outlet.
Do not attempt to use your tness bike for any purpose other than for the purpose it is
intended.
The hand pulse sensors are not medical devices. Various factors, including the user’s move-
ment, may aect the accuracy of heart rate readings. The pulse sensors are intended only as
exercise aids in determining heart rate trends in general.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on
your tness bike. Quality athletic shoes are recommended to avoid leg fatigue or injury.
SAVE THESE INSTRUCTIONS - THINK SAFETY!
IMPORTANT SAFETY INSTRUCTIONS

B94 / R92 FITNESS BIKE3
WARNING!
NEVER remove any cover without rst disconnecting AC power.
If voltage varies by ten percent (10%) or more, the performance of your tness bike may be
aected. Such conditions are not covered under your warranty. If you suspect the voltage is
low, contact your local power company or a licensed electrician for proper testing.
NEVER expose this tness bike to rain or moisture. This product is NOT designed for use out-
doors, near a pool or spa, or in any other high humidity environment. The operating tempera-
ture specication is 40 to 120 degrees Fahrenheit, and humidity is 95% non-condensing
(no water drops forming on surfaces).
IMPORTANT ELECTRICAL INSTRUCTIONS
NEVER operate this tness bike without reading and completely understanding the results
of any operational change you request from the computer.
NEVER use your tness bike during an electrical storm. Surges may occur in your household
power supply that could damage tness bike components. Unplug the tness bike during
an electrical storm as a precaution.
Do not use excessive pressure on console control keys. They are precision set to function
properly with little nger pressure. Pushing harder is not going to make the unit go faster
or slower. If you feel the buttons are not functioning properly with normal pressure contact
your SOLE dealer.
IMPORTANT OPERATION INSTRUCTIONS

4B94 / R92 FITNESS BIKE
B94 ASSEMBLY PACK CHECKLIST
HARDWARE STEP 1
1
#71. 3/8” x 25mm x 2T
Flat Washer (4 pcs)
#50. 3/8” x 2”
Hex Head Bolt (4 pcs)
HARDWARE STEP 2
2
#72. 5/16” x 18mm x 1.5T
Flat Washer (6 pcs)
#51. 5/16” x 5/8”
Hex Head Bolt (7 pcs)
#99. 5/16” x 19 x 1.5T
Curved Washer (1 pc)
HARDWARE STEP 3
3
#72. 5/16” x 18mm x 1.5T
Flat Washer (2 pcs)
#51. 5/16” x 5/8”
Hex Head Bolt (2 pcs)
#103. 5/16” x 1.5T
Split Washer (2 pcs)
HARDWARE STEP 4
4
#58. M5 x 12mm
Phillips Head Screw (8 pcs)

B94 / R92 FITNESS BIKE5
#93. Phillips Head Screwdriver
ASSEMBLY TOOLS
#92. 13/15mm Wrench
#100. 12/14mm Wrench
1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along
the dotted Line. Lift Box over the unit and unpack.
2. Carefully remove all parts from carton and inspect for any damage or missing
parts. If damaged parts are found, or parts are missing, contact your dealer
immediately.
3. Locate the hardware package. Remove the tools rst. Remove the hardware
for each step as needed to avoid confusion. The numbers in the instructions
that are in parenthesis (#) are the item number from the assembly drawing
for reference.
PRE-ASSEMBLY
B94 ASSEMBLY INSTRUCTIONS
15

6B94 / R92 FITNESS BIKE
HARDWARE STEP 1
1. Attach the Rear Stabilizer (5) onto the Main Frame (1) with the four Hex Head
Bolts (50) and four Flat Washers (71). Tighten using the 12/14mm Wrench
(100).
REAR STABILIZER
1
1. Unravel the Computer Cable (29) and pull the twist tie wire through the
Console Mast Cover (38) (see illustration for the correct orientation of the
cover)and the Console Mast (2) until the cable connector comes out the top
opening of the console mast
2. Attach the Console Mast (2) onto the Main Frame (1) with the seven Hex
Head bolts (51). Place six Flat Washers (72) on the side bolts and one Curved
Washer (99) on the front bolt. Tighten using the 12/14mm Wrench (100).
CONSOLE MAST
2HARDWARE STEP 2
#50. 3/8” x 2”
Hex Head Bolt (4 pcs)
#71. 3/8” x 25 x 2T
Flat Washer (4 pcs)
#51. 5/16” x 5/8”
Hex Head Bolt (7 pcs)
#72. 5/16” x 18 x 1.5T
Flat Washer (6 pcs)
#99. 5/16” x 19 x 1.5T
Curved Washer (1 pcs)

B94 / R92 FITNESS BIKE7
1. Insert the Computer Cable (29) and two Hand pulse cables (26) into the
connectors in the back of the Console (34).
2. Attach the Console (34) onto the Console Mast (2) with four Phillips Head
Screws (58). Be careful not to pinch the cables when fastening.
3. Attach the Front Stabilizer Cover (40) and the Rear Stabilizer Cover (41) to the
Main Frame (1) with four Phillips Head Screws (58). Tighten with the Phillips
Head Screw Driver (93).
4. Install the Pedals (45 L, 46 R) onto the Cranks by using the 13/15mm Wrench
(92). Remember that the left pedal has a reverse thread and will be screwed
into the crank in the opposite rotation from normal threads. There is an L
stamped into the end of the threaded post of the left pedal and an R on the
end of the right post. Make sure to tighten the pedals as much as you
possibly can. It may be necessary to re-tighten the pedals if you feel a
thumping while pedaling the bike. A clicking noise or thumping feeling is
usually caused by loose pedals.
5. Install the Seat mount slide (7) onto the track on top of the seat tube with the
seat post facing forward. Place the nut plate (8) onto the seat slide behind the
seat post. Place the at washer (71) onto the fore/aft adjustment knob (86)
and thread it into the nut plate from underneath the seat tube track. Attach
the seat (19) to the seat post using the 12/14mm Wrench (100).
PLASTIC PARTS
4HARDWARE STEP 4
1. Remove the plastic tie from the center of the handlebar (3). Insert the two
hand pulse cables (26) through the opening of the handlebar mounting
bracket on the front side of the console mast tube (2). Pull the cables through
the opening of the console mounting bracket at the rear of the console mast
tube
2. Attach the Handle Bar (3) to the Front Console Mast (2) with the two Hex
Head bolts (51), two Flat Washers (72) and two Split Washers (103). Tighten
using the 12/14mm Wrench (100). Be careful not to pinch the cables when
fastening.
HANDLEBAR
3HARDWARE STEP 3
#51. 5/16” x 5/8”
Hex Head Bolt (2 pcs)
#72. 5/16” x 18 x 1.5T
Flat Washer (2 pcs)
#103. 5/16” x 1.5T
Split Washer (2 pcs)
#58. M5 x 12mm Phillips
Head Screw (8 pcs)
See page 8 for illustration

8B94 / R92 FITNESS BIKE
ASSEMBLY STEP 4
4