Soleus Air WM1-15E-01 User manual

Electronic Window Air Conditioner
Operating Instructions
V170124
Models
WM1-15E-01
15,400 BTU
WM1-18E-01
18,300 BTU
WM1-24E-01
24,700 BTU

Thank you for choosing a Soleus Air Air Conditioner. This owner’s manual will provide you with
valuable information necessary for the proper care and maintenance of your new product. Please take
a few moments to thoroughly read the instructions and familiarize yourself with all the operational
aspects of your new air conditioner.
For your own records, please attach a copy of your sales receipt to this manual. Also, write the store
name/location, date purchased, and serial number below:
Store Name:
Location:
Date Purchased:
Serial Number (located on back of unit):
Before installing and using your air conditioner, please read this owner’s manual carefully. Store this manual in a
safe place for future reference. Your safety and the safety of others is very important to us. Please pay attention to
all safety messages outlined in this owner’s manual.
WARNING: To reduce the risk of fire, electrical shock or injury when using your air conditioner, follow
the following basic precautions:
Plug into a grounded 3 prongoutlet.
Do not remove the ground prong.
Do not use a plug adapter.
Do not use an extensioncord.
Unplug the air conditioner before servicing
Use two or more people to move and install theair
conditioner
This is a safety alert symbol.
This symbol alerts you to potential hazards that can harm you or others or even cause
death.
All safety messages will directly follow the safety alert symbol and/or the words
“DANGER” or “WARNING”.
All Safety messages alert you of potential hazards, how to reduce the chance of injury,
and what can happen if instructions are not followed correctly.
Failure to immediately follow these
instructions may cause serious injury
or even death.
PURCHASE INFORMATION
SAFETY INSTRUCTIONS

This air conditioner is equipped with an LCDI (Leakage Current Detection and Interruption) power cord and
plug as required by US National Electric Code 440.65. This cord consists of a length of shielded flexible cord
with no termination on the load side and a LCDI attachment plug on the line side.
The LCDI power cord and plug will remove the supply source via electrical disconnect (circuit trip) if the
nominal current leakage between the cord shield and either load conductor exceeds a predetermined value.
The cord will remain de-energized until the devise has been manually reset. This is intended to reduce the risk
of a fire in the power cord or combustible materials nearby. The cord shields are not grounded and they must
be considered a shock hazards if exposed. The cord shield must not be connected to ground or to any exposed
metal.
The test and reset buttons on the LCDI Plug are used to check if the plug is functioning properly. To test:
1. Plug power cord into wall outlet. The LED light will turn on.
2. Press TEST Button, circuit should trip, cutting power to the air conditioner. When this occurs,
the LED light will turn off.
3. Press RESET button to restore power to the machine. Once power is restored, the LED light
will turn on again.
If test button is pressed and unit can still be turned on, current leakage has been detected. Do not use the air
conditioner or attempt to reset the LCDI Plug. Contact Soleus Air Customer Service for troubleshooting
recommendations.
LED LIGHT
Note: Your units power cord and plug may differ from the one shown.
WARNING:
1. DO NOT press the TEST button while the air conditioner is operating.
2. The TEST and RESET buttons should not be used as “ON” and “OFF”switches.
3. The cord and plug are not intended to offer protection to externally connected loads or supply circuits.
4. The cord and plug are intended for indoor use only.
POWER CORD AND PLUG

Hardware
(in plastic bag) Qty.
Sash Lock 1
Screw and 4
Locknut
Flathead Bolt 2
and Locknut
Sill Angle 2
Bracket
Curtain Lock 2
Non-Hardware Part List
Long Screws 13
Short Screws 10
Window Air Conditioner (1)
Remote Control (1)
AAA Batteries (2)
Top Mounting Rail (1)
Foam Gasket (1)
Curtain (2)
Window Sash Seal (1)
Foam Seal for Bottom Rail (1)
Owner’s Manual (1)
Weather Insulation Board (2)
CURTAIN
CURTAIN LOCK
FOAM SEAL FOR
BOTTOM RAIL
SCREWS AND
LOCKNUTS
FRAME
ASSEMBLY
WINDOW SUPPORT
BRACKET
Weather Insulation Board
SILL ANGLE BRACKET
FLATHEAD BOLT LOCKNUT
Remote Control 2 AAA Batteries Owner's Manual
WINDOW SASH SEAL
SASH LOCK AND
SHORT SCREW
FOAM GASKET TOP MOUNTING
RAIL
SHORT SCREW
TOOLS NEEDED
Large Flathead Screwdriver
Tape Measurer
Adjustable Wrench or Pliers
Pencil
Level
Socket Wrenches
Phillips Head Screwdriver
PACKAGE CONTENTS

Noise level is measured at a distance of 3.28 ft away from the front of the unit in cooling mode.
Power consumption is measured when the fan runs at the highest speed setting.
These specifications are for reference only. For actual data, please refer to the rating label on the back of the unit.
Model
WM1-15E-01
Power Supply (Ph/V/Hz)
1/115/60
Rated Cooling Capacity (BTU/h)
15,400
Cooling Power Input (Watts)
1,230
Rated Current Cooling (Amperage)
12
EER
11.8
Noise Level dB(A) (L/H)
55/59
Airflow CFM (H/L)
700/610
Dehumidifying Capacity
74 Pints per day
Product Dimensions (W” x H” x D”)
23.625 x 17.75 x 25.375
Package Dimensions (W” x H” x D”)
26.125 x 20 x 30.5
Net/Gross Weight (Lbs)
110/121
Refrigerant Type
R-410A
Plug Type
NEMA 5-15P
Model
WM1-18E-01
WM1-24E-01
Power Supply (Ph/V/Hz)
208/230/60
208/230/60
Rated Cooling Capacity (BTU/h)
18,300
24,700
Cooling Power Input (Watts)
1,530
2,330
Rated Current Cooling (Amperage)
6.7
10.3
EER
11.8
10.3
Noise Level dB(A) (L/H)
56/61
56/61
Airflow CFM (H/L)
730/630
760/660
Dehumidifying Capacity
83 Pints per day
152 Pints per day
Product Dimensions (W” x H” x D")
26.375 x 18.625 x 26.625
26.375 x 18.625 x 26.625
Package Dimensions (W” x H” x D”)
29.5 x 20.875 X 31.125
29.5 x 20.875 X 31.125
Net/Gross Weight (Lbs)
132/154
141/163
Refrigerant Type
R-410A
R-410A
Plug Type
NEMA 6-15P
NEMA 6-20P
SPECIFICATIONS

DISCLAIMER
ALL INFORMATION AND THE TECHNICAL SPECIFI-
CATIONS PRESENTED IN THIS USER’S MANUAL
ARE THE PRESENTATION OF THE MANUFAC-
TURER. SOLEUS N.A HAS NOT CON-DUCTED
INDEPENDENT TEST TO THE INFORMA- TION AND
THE SPECIFICATIONS PRESENTED HEREWITHIN.
WARNING:
Avoid fire hazard or electronic shock,
DONOT use an extension cord or an adapter plug.
DONOT remove any prong from the power cord.
DO NOT
under any circumstances,
cut, remove, or bypass the
grounding prong!!
Power supply cord with 3-prong grounding
plug and current detection device
ELECTRICAL SAFETY

Window Preparation
Please read all instructions prior to installing your air conditioner. Two people are recommended to install this product. If
a new electrical outlet is required, have the outlet installed by a qualified electrician before installing the unit.
Before installing the unit, check the dimensions of your window to make sure the air conditioner will fit. This unit is made
to fit inside a standard double-hung window. Make sure the window is in good shape and able to firmly hold the needed
screws. If not, make repairs prior to installing the unit.
Model
WM1-15E-01
WM1-18E-01 / WM1-24E-01
Unit Height
17 33/4"
18 5/8"
Unit Width
23 5/8"
26 3/8"
Min.Window Opening(See FIG
1)
18 4/3"
19 7/8"
Min. Window Width
28 1/8"
30"
Max Window Width
41 3/4"
50 "
Storm Window Requirements
A storm window frame will not allow the air conditioner to tilt properly which in turn will keep it from draining properly. To
adjust for this, attach a board or piece of wood to the sill. The board or wood piece should have a depth of at least 1 1/2”.
Make sure the board or piece of wood is approximately 1/2” higher than the storm window frame. This will allow the air
conditioner to tilt enough for proper drainage. (See FIG. 2).
FIG. 1 FIG. 2
19 7/8"MIN
Prior to Installing the Air Conditioner
1. Check for anything that could block airflow. Check the area outside of the window for things such as shrubs, trees,or
awnings. Check the inside area to make sure curtains, drapes, or blinds will not prevent proper airflow.
2. Check the available electrical outlet. The power supply must be the same as shown on the unit serial nameplate
(located on the left side of the unit, near the front faceplate). Be sure the outlet is close enough for the power cord to
reach.
3. Carefully unpack the air conditioner. Remove all packing material and make sure the floor is protected when remov-
ing. Due to the large size of this air conditioner, two people should move the unit together.
When handling the unit, be careful to avoid cuts from
the sharp metal edges and aluminum fins on the front
and rear coils.
18 3/4", /
18 3/4", / 19 7/8"MIN
INSTALLATION
ION

INSTALLATION & ASSEMBLY INSTRUCTIONS - WINDOW MOUNTING
REMOVE CHASSIS
1. Pull down the front panel and remove the filter. (See Fig.3)
2. Lift the front panel upwards to remove and place to theside.
3. Locate the four faceplate screws and remove. These screws will need to be re-installed prior to mounting the air con-
ditioner. (See Fig. 4)
4. After removing the screws, gently pull away the faceplate from the air conditioner cabinet. Remove the ground screw
and save for reinstallation later. (See Fig. 5 & 6)
5. Remove the two screws from top of the unit. (See Fig. 7) Hold the cabinet while pulling on the base handle, and care-
fully remove the unit.
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
INSTALLATION
ION

Curtain Installation
Top Mounting Rail
1. Attach the top mounting
rail to the unit with short
screws (Fig.8)
Fig. 8
2. Slide the free end of the curtain into the side panel of theair
conditioner. Do this for each side. The flange for securing
the curtain into the window sill will be facing the room side
when installed ( Fig.9).
Weather Insulation Board Fig.11
Curtain
Curtain
Fig. 9
Placing the Cabinet Inside the Window
1. Set the cabinet in the window so that is centered.
Place the unit so that front edge of the bottom railis
against the back edge of thesill.
2. Bring the window down so that the front edge ofthe
top rail is in front of the window. Be sure the unit is
tilting slightly to the outside.
3. Fasten the curtains to the unit with short screws(Fig.10). Window
Frame
1/4”
Top Rail
Bottom Rail
Fig. 10
Weather Insulation Board Installation
NOTE: The Weather Insulation Board adds an extra layer of insulation
to keep air from passing through the sides of the window air conditioner.
1. Using a sharp blade or scissors, slowly cut the Weather
Insulation Board to a size that will fit inside of the sidecur-
tain rails and completely cover thecurtain.
2. Once properly sized, remove the backing to expose thead-
hesive tape.
3. Place the Weather Insulation Board over the left curtainand
firmly press and hold for 5seconds.
3. Fasten cabinet to window sill using three long screws. Pre-
drill holes if needed. Add the bottom rail seal overthe
screws (Fig.12).
Bottom Rail Seal
4. Repeat above steps to install the Weather InsulationBoard
on right curtain (Fig.11). Fig. 12 Long Screw
INSTALLATION
ION

Install Support Brackets
1. Hold each support bracket flush against the outside of
the window sill. Tighten each bracket to the bottom of
the cabinet as shown below. Mark the brackets at top
lever of the window sill and then remove.
Install the Window Lock and Sash Seal
1. Trim the sash seal to fit the width of the window.Insert
the sash seal into space between the upper and lower
sashes.
MARK
2. Attach the right angle safety lock as shownbelow.
2. Assemble the sill angle brackets to the support brack-
ets at the marked position as shown above. Hand
tighten, but not all the way for any changes that may
need to be made later duringinstallation.
3. Install the support brackets (with sill angle brackets
attached) to the bottom of the cabinet as shownbelow.
4. Tighten all 6 boltssecurely.
SCREW &
LOCKNUTS
SAFETY LOCK
LONG SCREW
INSTALLATION
ION