Sony Ericsson Cyber-shot C905 Programming manual

C905
1222-9526 rev. 1
Troubleshooting Manual
APPENDIXCOMPONENT OVERVIEW FUNCTIONAL OVERVIEW
ABOUT
ABOUT TROUBLESHOOTING MEASUREMENT POINTS
C905
SEMC Troubleshooting Manual
1(124)

C905
1222-9526 rev. 1
ABOUT
ABOUT
ABOUT
General information
The purpose of this document is to provide enhanced technical information for Sony Ericsson
repair technicians in order to assist during service, repair and troubleshooting operations on Sony
Ericsson mobile phones. It should be used as a complement to other repair instructions and tools
as notified by the local Sony Ericsson representative.
To search for components throughout the entire document use the “search” function in Adobe
Acrobat Reader 7.0 (or later version) and enter the component name or other word. Use zoom to
enlarge.
For easier navigation of the document you can use the bookmarks that appear in the Bookmarks
tab on the left side of the Adobe Acrobat Reader window. Each bookmark jumps to a page in the
document.
Disclaimer
This document is Sony Ericsson confidential and should be treated as confidential in accordance
with the agreement with Sony Ericsson. This document is intended for use by authorized service
technicians only. Sony Ericsson is not to be held responsible for any damages or losses caused
intentionally or unintentionally due to unauthorised use of the information in this document.
Rev. Date Changes / Comments
112/05/2008Inititalrevision.
Revision History
Contents
ABOUT 2
Contents 2
Equipment List 3
TROUBLESHOOTING 8
Power On/Off Problems 8
USB and Software Flash Problems 8
Dead Phone Problems 9
Display Problems 10
Display Illumination Problems 11
Opto Sensor Problems 11
On-Off Key Problems 12
Numeric Keypad &
Camera Snap Button Problems 12
Navigation Keypad & Game Button Problems13
Volume Button Problems 13
Camera Play and Mode Button Problems 14
Numeric Keypad LED Problems 14
Navigation Keypad LED Problems 15
Auto Focus LED Problems 15
Back Side LED Problems 16
Tally LED Problems 16
Camera Snap Button LED Problems 17
Camera Navigation LED Problems 17
Trickle Charge LED Problems 18
Xenon Flash Problems 18
Multimedia Combo Chip Problems 19
Camera Problems 19
Camera Cover Detect Problems 20
TV Out Problems 20
Charging Problems 21
USB/VBUS Charging Problems 21
SIM Problems 22
Memory Stick Problems 22
Primary & Secondary Mic Problems 23
Ear Speaker Problems 23
Loudspeaker Problems 24
Handsfree (PHF) Problems 24
FM Radio Problems 25
FM Radio Antenna Problems 25
Bluetooth Problems 26
WLAN Problems 26
GSM Problems 27
WCDMA I, II and V Problems 27
WCDMA VIII Problems 28
A-GPS Problems 28
Accelerometer Problems 29
Vibrator Problems 29
Real Time Clock Problems 30
Slide Sensor Problems 30
System Connector Protection Test 31
Current Consumption Test 31
Backup Capacitor Test 33
Charging Test 33
ASIC Revision Test 34
Measurement Points Pictures 35
MEASUREMENT POINTS 52
Front Side 52
Back Side 53
Top Schematic 54
Audio Top 55
Audio Analog 56
Audio Digital 57
Audio FM Radio 58
Application & System Performance Top 59
System Top 60
System Control - Clocks & Resets 61
System Memories 62
System PoP IF 63
Power Top 64
Power Regulators & Charging 65
Power Imaging 66
Power ASICs 67
Power WLAN 68
Connectivity Top 69
Connectivity I2C & ADC 70
Connectivity Cards 71
Connectivity 72
Connectivity Keypad 73
Connectivity Video Companion Chip 74
Imaging Top 75
Imaging Display 76
Imaging Camera 77
Imaging LMU & Flash 78
Access Top 79
Access GSM & UMTS 80
Access Bluetooth 81
Access AGPS 82
Access WLAN 83
Test 84
COMPONENT OVERVIEW 85
Front Side 85
Back Side 86
FUNCTIONAL OVERIEW 87
Technical Description 87
Platform Block Diagram 99
Block Diagram Power Distribution 100
Block Diagram Clocking Concept 101
APPENDIX 102
Replaceable Parts 102
Components - L2200, L4201-04 103
Components - L2406, L4200 103
Components - N1210, N1211 104
Components - N1510, N2200 104
Components - N1300, N2206 105
Components - N2212, N2213 105
Components - N2300, N2410, N2411 106
Components - N2420, N2421, N2422 107
Components - N2500, N2700, N3100 108
Components - N3101, N4400, S2415 109
Components - V2200, V2202 109
Components - V2412, V2417 109
Components - V2414-16, V2470, V4201 110
Components - V4203, X1200, X1210-11 110
Components - X1540, X2201 111
Components - X2401, X2402 111
Components - X2410, X4200, X4300 112
Components - X4311-15, X4400 112
Components - X4410, Z2400, Z4200-02 113
Keyboard FPC Schematics 114
Troubleshooting Software Documentation 115
Troubleshooting Fixture Setup Instructions 122
SEMC Troubleshooting Manual
2(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Equipment List
C905 Equipment List
Note! Additional information about the equipment used for TRS can be found in the following
locations:
Location 1: CSPN – Repair Instructions – Additional Soldering Process – C905, C905a or C905c –
Equipment List.
Location 2: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pd
f
or matris.xls – C Model Tab.
Troubleshooting Fixture
Location: CSPN – Repair Instructions – Additional Soldering Process – C905, C905a or C905c –
Equipment List.
Part number: 1218-4986
Note! Additional information about the TRS Fixture Kit can be found in the Trouble Shooting
Fixtures Setup Instructions document which is included in the appendix of this manual.
Dummy Battery
Location: CSPN – Repair Instructions – Additional Soldering Process – C905, C905a or C905c –
Equipment List.
Part number: 1208-5627
Note! The resistance between GND and BDATA should be approximately 27K Ohm.
Instruments
Power Supply Channel 1 (VBATT)
Agilent 6632B or similar
Location:CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Instrument Settings:
Voltage: 3.8 Volt
Limiter: 2.0 A
Note! Maximal cable length between the Power Supply Channel 1 VBATT and the dummy battery
cannot be more than 1 meter. The cable must be able to handle at least 16A.
Power Supply Channel 2 (DCIO/SEPI)
Agilent 6632B or similar
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Instrument Settings:
Voltage: 5.0 Volt
Limiter: 2.0 A
Oscilloscope
Agilent DSO7052A or similar
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Digital Multimeter (DMM)
Fluke 83 or similar
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Note! The 0, 64 mm Test Probes is recommended by Sony Ericsson when DMM is in use
see Picture 1.
Picture 1
Spectrum Analyzer
R&S FSL 9 kHz – 3 GHz or similar
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
RF probe
HP 85024A or similar
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Mobile Phone Tester
Yokogawa VC200 or similar
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
FM Signal Generator
R&S SMC100A or similar
Location: -
SEMC Troubleshooting Manual
3(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Equipment List
RF Adaptor
Adaptor 33 N-BNC-50-1
Adaptor to Signal Generator RF Output
See Picture 2
Location: -
Picture 2
PC Package & PC Software
PC Package (Computer)
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Urquell Fault Trace SW with project file
Location: CSPN – Repair Instructions - Electrical – C905, C905a or C905c – Trouble Shooting
Application
Project File: C905, C905a, C905c Project_R1A
Drivers
SEPI BOX Drivers
Location: http://emma.extranet.sonyericsson.com – Drivers – DSS / SEPI / SEMUTS
SE Communication Interface SEPI BOX
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Part number: LTN 214 1484
See Picture 3.
Picture 3
Cables
USB Computer Cable
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – Re
See Picture 4.
Picture 4
DSU-60/USB Cable
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – Re
Part number: KRY 101 1413
RF Test Cable Flexible
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – Re
Part number: RPM 119 885
See Picture 5.
Picture 5
SEPI Interface Cable – A1
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – Re
Part number: KRY 101 1119/1
See Picture 6.
Picture 6
SEMC Troubleshooting Manual
4(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Equipment List
Power Cable RED to Power Supply Channel 1 (VBATT)
Maximum Length: 1m
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Power Cable BLACK to Power Supply Channel 1 (VBATT)
Maximum Length: 1m
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Customized Power Supply Channel 2 Cable (DCIO/SEPI)
Customize the cable according to following instructions below:
(Step 1, Step 2, Step 3 and Step 4)
Step 1:
Take the CST-75 battery charger and cut of the charger according to Picture 7.
Picture 7
Note! The Cable length must be exactly 1.3 meters.
Step 2:
Connect the CST-75 charger Red or White wire to the Plus Output and the Black wire to the Minus
(GND) Output at backside of the Power Supply Channel 2 (DCIO/SEPI) according to Picture 8.
Picture 8
Step 3:
Cut off insulating material from the inside of the charger plug according to Picture 9.
Picture 9
Step 4:
Connect DCIO Cable and SEPI Interface Cable – A1 according to Picture 10.
Picture 10
Picture 11
Note! The setup example presented in the Picture 11 is wrong!
SEMC Troubleshooting Manual
5(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Equipment List
Connection Instructions for the Dummy Battery
This is the correct setup when using the Dummy Battery.
See Pictures 12 and 13.
Picture 12
Picture 13
Customized FM Radio Cable
Step 1:
Use the Test lead BNC-4mm 1,5m Cable, see Picture 14.
Picture 14
Product Name: Test lead BNC-4mm 1,5m
Product Description: Test lead with 4 mm lab plugs at one end and a BNC plug at the other.
Manufacturer: PMK Germany
Location: http://www.elfa.se/en/ or other supplier.
Part number: 46-310-40
Note! This is the ELFA part number.
Step 2:
Cut the Red Lab Plug connector according to Picture 15.
Picture 15
Step 3:
Use any Hands-Free (PHF) Cable and cut it according to Picture 16.
Picture 16
Note! Cable length should be at least 40 cm.
Step 4:
Only use the Wire that is connected to PIN2 and cut out all others according to Picture 17.
Picture 17
Note! Use DMM instrument to ensure which of the wires are connected to PIN2 at Hands-Free
(PHF) system connector plug.
SEMC Troubleshooting Manual
6(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Equipment ListEquipment ListEquipment List
Step 5:
Connect the Cable from the Picture 15 and Cable from the Picture 17 according to Picture 18.
Note! Use a soldering iron for this action and then use insulating material to protect the contact
point.
Picture 18
Test Cards
Local SIM
Any functional Local SIM Card
See Picture 19.
Picture 19
Test SIM GSM/UMTS
One Test SIM GSM/UMTS is needed to perform Current Consumption Test, see Picture 20.
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – RepairToolsCatalogue.pdf
Note! To buy a Test SIM GSM/UMTS, please contact your supplier of test equipment.
Picture 20
Sony Memory Stick M2
Any functional Memory Stick Micro M2 Card
See Picture 21.
Picture 21
SMK RF Probe
Location: CSPN – Repair Instructions – Mechanical – Tool Catalogue – Re
Part number: SXA 109 6356
See Picture 22.
Picture 22
SEMC Troubleshooting Manual
7(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Power On/Off Problems - USB and Software Flash Problems
1. Customize the phone into DPY/Z
2. Startup the phone and wait for
the configuration to take place
(takes less than a minute)
3. Customize with correct CDA
4. Activate the phone
No
No
START
Use
Dummy Battery
Connected to
Power Supply Channel 1
(VBATT)
Go to
Dead phone
Problems part 1
TRS guide
Yes
No
No
Connect a chargerNo
Yes
Go to
On-Off Key Problems
TRS guide
Yes
Go to
Dead Phone
Problems part 1
TRS guide
Yes
Yes
Go to
System Connector
Protection Test
After this go to
USB and Software
Flash Problems TRS
guide
Yes
Yes
NoYes
No
Is the phone
consuming more than
1mA when the phone
is powered off
Is it possible to
power on the phone
Is the
phone consuming
any current when
powering on the
phone
Is the Problem
solved
Is the phones
behavior as normal
Optimized
charging
Is the
Flash process
started
Flash
The phone with
ITP software.
Is the ITP Flash
Successful
Is the Problem
solved
Is it possible to power
off the phone
Yes
Go to
Current
Consumption Test
After this go to
Charging Test
Yes
No
Claim for a
SW Upgrade
Yes
No
No
Go to
USB and Software
Flash Problems
TRS guide
No
No
Is the current
consumption between
10mA to 70mA
CDA Software
Flash
Successful
Flash
the phone with
correct CDA
software
Yes
Flash
the phone with
correct CDA
software
Press ”C”
Connect USB from PC
Run SEMC BOOT
if necessary
Run SUCR SW
Is Phone Flash
OK
Power On/Off Problems
START
Step 1:
Perform
System Connector Protection Test
If successful go to step 2.
Step 2:
Load ITP SW into the Phone
Go to
USB/VBUS
Charging Problems
Does
the Phone
Indicate charging
on the display YesNo
Does the
Flash process
Start-up when using
EMMA SW
No
Yes
Is the
ITP SW Flash
Successful Yes SL 5 Replace
N2010
SL 4 Escalate
No
Use TRS Fixture
1: Connect: VBATT and DCIO/SEPI
2: Remove: DCIO/SEPI
3: Connect: USB Cable from the PC
2.7V – 3.3V DC
at MP 9 (C2436) and
1.8V DC at MP 7
(C2435)
Yes Yes
No
Is
MP X2405_Pin 10
Short circuit to the
PBA GND (Shield
Can Fence)
Yes Replace
V2415
Is the
MP X2405_Pin 11
Short circuit to the PBA
GND (Shield
Can Fence)
No
Replace
V2416
Yes
5 Volt DC at
MP 6 (C2433) No
SL 4 Replace
N2420
SL 5 Replace
R2442
No
1.8 Volt DC at
MP 8 (R2431)
Yes
SL 5 Replace
N2010
SL 4 Escalate
No
Replace
N2420
Disconnect:
VBATT and USB Cable
Max
2 Ohm between
MP X2405_Pin 11 and
MP 10 (Z2400_Pin 3)
Max
0.5 Ohm between
MP X2405_Pin 11 and
MP 13 (Z2400_Pin 2)
No Replace
X2405
No
Replace
Z2400
Yes
Max
2 Ohm between
MP X2405_Pin 10 and
MP 12 (Z2400_Pin 4)
Max
0.5 Ohm between
MP X2405_Pin 10 and
MP 11 (Z2400_Pin 1)
Yes
No Replace
X2405
No
Replace
Z2400
Yes
SL 4 Replace
N2420
SL 5 Replace
N2010
Yes
USB and Software Flash Problems
SEMC Troubleshooting Manual
8(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Dead Phone Problems
START
Step 1:
Try to recover the phone by using
EMMA SW
Press ”C”
Connect USB from PC
Run SEMC BOOT if necessary
Run SUCR SW
If successful claim SW Flash
If not continue with the step 2.
Step 2:
Use TRS Fixture
Connect Only: VBATT
Is the
current consumption
more than 1mA
Try to trace
Faulty Component
by using Freezing Spray
Is the
Radio Module
N1200 (Tiger)
getting hot
Replace
N1200 Yes
No
No
Yes
Connect:
DCIO/SEPI to the Phone
Is the
connection between
MP 137 (X2201_Pin 3)
and PBA GND (Shield
Can Fence)
Ok
Yes
SL 4 Replace
X2201
SL 5 Replace
R2200
No
SL 5 Remove
N2000
SL 4 Escalate
32 kHz at
MP 136 (C2100) and
MP 138 (C2101)
Replace
B2100
No
32 kHz
RTCCLK at
MP 135 (ST2104)
Yes
No
26 MHz
MCLK at
MP 38 (R2102)
Yes
Yes
1.8V DC
At MP 164
(ST2203 VDDE18) and 2.8V
DC at MP 163 (C1218
LDOA_OUT)
NoNo
Yes
Check the following
Voltages:
2.6V MP 125 (ST2201 VAUDIO26)
2.5V MP 165 (ST2202 VANA25)
2.7V MP 127 (ST2204 VBT27)
2.7V MP 126 (ST2205 VDIG)
2.6V MP 124 (ST2206 VBEAR26)
1.2V MP 116 (ST2209 VCORE12)
1.8V MP 40 (ST2225 VCORE18
and VMEM18)
2.8V DC
at MP 65 (C1207)
(If C905c skip this
and replace
N1200)
Replace
N1200 Yes
Replace
N1211 No
Is the
all Voltages
Ok
Step 1:
Disconnect:
VBATT and DCIO/SEPI
Step 2:
Connect:
Key Flex Assy and Slider FPC Assy
to the PBA
Connect: VBATT Only
Step 3:
Use EMMA SW
Press the ”C” key and Connect
USB Cable from the PC to the PBA
Flash the Phone with ITP SW
Yes
Is the
ITP SW Flash
Successful
SL 5 Replace
N2020
SL 4 Escalate Yes
Go to USB and
Software Flash
Problems TRS guide No
No
Go to
Dead Phone
Problems part 2
SL 5 Replace
N2000
SL 4 Escalate
SL 5 Replace
N2000
SL 4 Escalate
Is the
current consumption
still more than
1mA
Try to trace Faulty
Component by using
Freezing Spray Yes
SL 5 Replace
N2000
SL 4 Escalate No
Dead Phone Problems part 1
START
NOTE !
Before following this guide the
Dead Phone Problems part 1 TRS guide
must be finished
Is the
VAUDIO26
Voltage
Ok
No
Is the
VANA25
Voltage
Ok
Yes
Is any of
N2200 or N2010
getting hot
No Yes
SL 5 Replace
N2000
SL 4 Escalate
No
Is the
VBT27
Voltage
Ok
Yes
Is N1300
getting hot
No
Is any of
N2422 or N3103
getting hot
SL 4 Replace
N2422
SL 5 Replace
N3103
Yes
No SL 5 Replace
N2000
SL 4 Escalate
SL 4 Replace
N2200
SL 5 Replace
N2010
Replace
N1300
Yes
No SL 5 Replace
N2000
SL 4 Escalate
Is the
VDIG
Voltage
Ok
Is any of
N2411, N1300
N1500 or N1510 getting
hot. (Note: The N1500
is missing on
C905c)
SL 4 Replace
N2411, N1300
or N1510
SL 5 Replace
N1500
Yes
Yes
No
No SL 5 Replace
N2000
SL 4 Escalate
Yes
Go to
Dead Phone
Problems part 3
Is the
VBEAR26
Voltage
Ok
No SL 5 Replace
N2000
SL 4 Escalate
Yes
Dead Phone Problems part 2
SEMC Troubleshooting Manual
9(124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Dead Phone Problems - Display Problems
START
NOTE !
Before following this guide the
Dead Phone Problems part 2 TRS guide
must be finished
Is the
VCORE12
Voltage
Ok
1.1V – 1.2V DC
at MP 115
(V2201_Cathode)
3.8 Volt DC at
MP 114 (L2201)
No Replace
L2201
No
Yes
No
Yes
Is
MP 116 (ST2209)
Short circuit to the
PBA GND (Shield
Can Fence)
Replace
L2200
No
SL 5 Replace
N2000 or N2010
SL 4 Escalate
Is the
VCORE18/VMEM18
Voltage
Ok
No
No
1.8 Volt DC at
MP 40 (ST2225)
SL 4 Replace
N2200
SL 5 Replace
N2010
No
Yes
Yes
Yes
Is the
ITP SW Flash
Successful
SL 5 Replace
N2020
SL 4 Escalate
Yes
No
Yes
SL 5 Replace
V2201 or N2000
SL 4 Escalate
Is
MP 40 (ST2225)
Short circuit to the
PBA GND (Shield
Can Fence)
SL 5 Replace
N2010
SL 4 Escalate
Yes
SL 4 Replace
N2200
SL 5 Replace
L2202
Step 1:
Disconnect:
VBATT and DCIO/SEPI
Step 2:
Connect:
Key Flex Assy and Slider FPC Assy
to the PBA
Connect: VBATT Only
Step 3:
Use EMMA SW
Press the ”C” key and Connect
USB Cable from the PC to the PBA
Flash the Phone with ITP SW
Go to USB and
Software Flash
Problems TRS guide
Dead Phone Problems part 3
Is the
Display Backlights
Ok
Go to
Dispaly illumination
Problems TRS guide
No
Is the picture
too dark or
too light
Yes
Go to
Opto Sensor
Problems TRS guide
No
Disconnect: VBATT and DCIO/SEPI and
Remove PBA from the TRS Fixture
Use Digital Multimeter instrument (DMM)
and perform:
Z4200, Z4201 and Z4202
Display Filter Test 1 and 2
NOTE !
Be very careful when you're cutting the
Shield Can Fence to avoid component damage
Yes
START
Step 1:
Flash the Phone with EMMA SUCR SW
If successful claim SW Flash
If not go to step 2.
Step 2:
Load ITP SW into the Phone
Use TRS Fixture
Connect:
PBA Key Flex Flip, Slider FPC Assy and Display
to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Display Pattern
Activate:
TV Test Pattern
If Display is working on the TRS Fixture
then Replace
Display, PBA Key Flex Flip or Slider FPC Assy
If not then continue with
Display illumination Problems TRS guide
It is recommended to use microscope for these
measurements
Z4200, Z4201 and Z4202
Display Filter Test
Test 1:
Check if Pins: 1,2,3,4,5,6,7,8
are NOT short circuit to GND
Test 2:
Max 2 Ohm between the following pins:
Pin 1 and 5
Pin 2 and 6
Pin 3 and 7
Pin 4 and 8
NOTE !
Test 1 and 2 must be made on all filters
Are all
Display Filters
Ok
Replace
Z4200, Z4201 or
Z4202
No
Replace
X4200
Yes
Is the Display
Problem solved
Claim Component
X4200
Yes
SL 5 Replace
N2010
SL 4 Escalate
No
Display Problems
SEMC Troubleshooting Manual
10 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Display Illumination Problems
TROUBLESHOOTING
- Opto Sensor Problems
START
Step 1:
Flash the Phone with EMMA SUCR SW
If successful claim SW Flash
If not go to step 2.
Step 2:
Load ITP SW into the Phone
Use TRS Fixture
Connect:
PBA Key Flex Flip, Slider FPC Assy and Display
to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Display Backlight
If Display Backlight is working on the TRS Fixture
then Replace
Display, PBA Key Flex Flip or Slider FPC Assy
If not then continue with the
Display ilumination Problems TRS guide
1: Ues Fault trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Deactivate:
Display Backlight
2: Disconnect Slider FPC Assy from the PBA
3.7V - 3.8V DC
at MP 51 (TP4200)
3.7V - 3.8V DC
at MP 119
(V4201_Anode)
No
Replace
V4201
Yes
Replace
L4200
No
Fault trace SW
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Display Backlight
Yes
17V - 20V DC at
MP 51 (TP4200)
More than
4 Volt DC
Pk-Pk Pulses
at MP 117
(V4200_Pin 3)
No
Yes
Replace
V4200
SL 5 Replace
N2000
SL 4 Escalate
No
0 Volt DC at
MP 52 (TP4201) Yes
Replace
X4200
Yes
Replace
V4203
No
Is the
Display illumination
Problem solved No
Claim Component
V4203
Yes
Display Illumination Problems
START
Step 1:
Replace PBA Key Flex Flip
and retest the Phone
If successful claim PBA Key Flex Flip
if not go to step 2.
Step 2:
Replace Slider FPC Assy
and retest the Phone
If successful claim Slider FPC Assy
if not continue with the
Opto Sensor Problems TRS guide
Is the
Display
Illumination (LEDs)
Ok
Go to
Dispaly illumination
Problems TRS guide
No
Can you see
any picture on
Display
Yes
Go to
Display Problems
TRS guide
No
Use TRS Fixture
Connect: VBATT and DCIO/SEPI
Yes
1.8 Volt DC at
MP 73 (R2217
OPTO_EN)
Shortly after phone
Power On
SL 5 Replace
N2000
SL 4 Escalate
No
Yes
3 Volt
Pk-Pk Pulses at
MP 59 (TP2203
VOPTO30) Shortly after
phone Power On
No
Replace
N2201
Replace
X4200
Yes
Is the
Opto Sensor Problem
solved
Claim Component
X4200
No Yes
SL 5 Replace
N2000
SL 4 Escalate
Opto Sensor Problems
SEMC Troubleshooting Manual
11 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING On-Off Key -
TROUBLESHOOTING
Numeric Keypad & Camera Snap Button Problems
START
Step 1:
Replace PBA Key Flex Flip and retest the Phone
If successful claim PBA Key Flex Flip
if not go to step 2.
Step 2:
Replace Slider FPC Assy and retest the Phone
If successful claim Slider FPC Assy
if not go to step 3.
Step 3:
Use TRS Fixture
Connect:
PBA Key Flex Flip and Slider FPC Assy to the PBA
Connect: VBATT and DCIO/SEPI
Is the
Problem with
Power Off
No
3.7 Volt DC at
MP 60 (C2472)
Yes
Press the
On/Off Key Yes
0 Volt DC at
MP 60 (C2472)
Replace
X4200 No
SL 5 Replace
N2000
SL 4 Escalate
Yes
Disconnect:
Slider FPC Assy
from the PBA
No
SL 4 Replace
V2470
SL 5 Replace
N2000
1.8 Volt DC at
MP 5 (R2470)
SL 5 Replace
R2470 or N2010
SL 4 Escalate
No
3.7 Volt DC at
MP 60 (C2472)
Yes
Replace
X4200 Yes
No
1.8 Volt DC at
MP 5 (R2470)
Replace
V2470 Yes
SL 5 Replace
R2470, V2480 or
N2010
SL 4 Escalate
No
On-Off Key Problems
START
Step 1:
If Problem with both Numeric and Navigation Keypads
go to step 3, if not go to step 2.
Step 2:
Use TRS Fixture
Connect:
Numeric Key Foil to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Activate
Keypad Scan Test
Perform Keypad Scan Test by pressing all
Keypads and Camera Snap Button on Numeric Key Foil
If successful then
Replace
Numeric Key Foil
If not go to step 3.
Step 3:
Use TRS Fixture
Connect:
Numeric Key Foil to the PBA
Connect: VBATT and DCIO/SEPI
and continue with the
Numeric Keypad and Camera Snap Button Problems
TRS guide
Is the
Problem with
both Numeric and
Navigation
Keypads
Replace
X2410 or X2411 No
Yes
1.8 Volt DC at
MP 96 (S2453_Pin A) and
MP 94 (S2454_Pin A)
Go to Volume
Up and Down Button
Problems TRS guide
No
Yes
Go to Camera
Play and Mode (REC)
Button Problems
TRS guide
No
Is the
problem with
Numeric Keypad and
Camera Snap
Button
No
Yes
Go to
Navigation Keypad
and Game A and B
Button Problems
TRS guide
1.8 Volt DC at
MP 82 (S2415_Pin A) and
MP 88 (S2424_Pin A)
Yes
1.8 Volt DC at
MP 76
(V2481_Cathode)
SL 5 Replace
V2481
SL 4 Escalate
No
Yes
1.8 Volt DC at
MP 5 (R2470), MP 4
(R2471) and MP 39
(R2472)
0 Volt DC
when pressing
Key ”3" at MP 5 (R2470)
Key ”6" at MP 4 (R2471)
and Key ”1" at
MP 39 (R2472)
Yes
Flash the Phone with
EMMA SUCR SW Yes
1: Disconnect:
VBATT and DCIO/SEPI
2: Disconnect:
Numeric Key Foil
from the PBA
No
Is
MP 157 (C2461),
MP 158 (C2462), MP 159
(C2464) Short Circuit to GND
(Shield Can
Fence)
SL 5 Replace
V2486,
V2487 or V2484
SL 4 Escalate
Yes
SL 5 Replace
N2010
SL 4 Escalate
No
Is
MP 5 (R2470)
MP 4 (R2471), MP 39 (R2472)
Short Circuit to GND
(Shield Can
Fence)
No
No
SL 5 Replace
V2480,
V2473 or V2479
SL 4 Escalate
Yes
SL 5 Replace
R2470, R2471 or
R2472
SL 4 Escalate
Numeric Keypad and Camera Snap Button Problems
SEMC Troubleshooting Manual
12 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING
TROUBLESHOOTING
Navigation Keypad & Game Button - Volume Button Problems
START
Step 1:
Use TRS Fixture
Connect:
PBA Key Flex Flip and Slider FPC Assy to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Activate
Keypad Scan Test
Perform Keypad Scan Test by pressing all Keypads and
Game A and B Buttons on Key Flex Flip Assy
If successful then
Replace
PBA Key Flex Flip or Slider FPC Assy
If not go to step 2.
Step 2:
Continue with the
Navigation Keypad and Game A and B Button Problems
TRS guide
NoYes
Is the
Numeric Keypad
and Camera Snap
Button
Ok
Go to
Numeric Keypad and
Camera Snap Button
Problems TRS guide
Replace
X4200
Navigation Keypad and Game A and B Button Problems
START
Use TRS Fixture
Connect: VBATT and DCIO/SEPI
Is
the problem with
S2453 Volume Up
Button
Yes
1.8 Volt DC at
MP 96 (S2453_Pin A) and
MP 97 (S2453_Pin B)
Press the
S2453 Volume Up
Button
Yes
0 Volt DC at
MP S2453_Pin A and
MP S2453_Pin B
No
Yes
Replace
S2453
No No
No
SL 5 Replace
N2010
SL 4 Escalate
Are
MP 96 (S2453_Pin A)
and MP 97 (S2453_Pin B)
short circuit to the PBA GND
(Shield Can
Fence)
SL 5 Replace
R2473 or N2010
SL 4 Escalate
Yes
Are
MP 96 (S2453_Pin A)
and MP 97 (S2453_Pin B) still
short circuit to the PBA GND
(Shield Can
Fence)
Remove the
S2453 Volume Up
Button
SL 5 Replace
V2474 or V2478
SL 4 Escalate
Yes Replace
S2453
No
1.8 Volt DC at
MP 94 (S2454_Pin A) and
MP 95 (S2454_Pin B)
Press the
S2454 Volume Down
Button
Yes
0 Volt DC at
MP 94 (S2454_Pin A) and
MP 95 (S2454_Pin B)
Replace
S2454 No
SL 5 Replace
N2010
SL 4 Escalate
Yes
Are
MP 94 (S2454_Pin A)
and MP 95 (S2454_Pin B)
short circuit to the PBA GND
(Shield Can
Fence)
No
SL 5 Replace
R2474 or N2010
SL 4 Escalate
No
Remove the
S2454 Volume Down and
S2424 Camera Play
Buttons
Yes
Are
MP 94 (S2454_Pin A)
and MP 95 (S2454_Pin B) still
short circuit to the PBA GND
(Shield Can
Fence)
Replace
S2454 and S2424 No
SL 5 Replace
V2477,V2476
or V2472
SL 4 Escalate
Yes
Volume Up and Down Button Problems
SEMC Troubleshooting Manual
13 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Camera Play and Mode Button
TROUBLESHOOTING
- Numeric Keypad LED Problems
START
Use TRS Fixture
Connect: VBATT and DCIO/SEPI
Is there
a problem with
S2424 Camera Play
Button
Go to Volume
Up and Down Button
Problems TRS guide
1.8 Volt DC at
MP 82 (S2415_Pin A)
and MP 84
(S2415_Pin B)
No
SL 5 Replace
N2010
SL 4 Escalate
Press the
S2415 Camera Mode (REC)
Button
Yes
0 Volt DC at
MP 82 (S2415_Pin A)
and MP 84
(S2415_Pin B)
Replace
S2415 No
Yes
No
1.8 Volt DC at
MP 88 (S2424_Pin A)
and MP 90
(S2424_Pin B)
Yes
Press the
S2424 Camera Play
Button
Yes
0 Volt DC at
MP 88 (S2424_Pin A)
and MP 90
(S2424_Pin B)
Replace
S2424 No
SL 5 Replace
N2010
SL 4 Escalate
Yes
1.8 Volt DC at
MP 96 (S2453_Pin A)
and MP 94
(S2454_Pin A)
Yes
No
Is the
MP 82
(S2415_Pin A)
and MP 84 (S2415_Pin B)
Short circuit to GND
(Shield Can
Fence)
No
SL 5 Replace
N2010
SL 4 Escalate
Remove the
S2415 Camera Mode (REC)
Button
Yes
Is the
MP 82
(S2415_Pin A)
and MP 84 (S2415_Pin B)
still Short circuit to GND
(Shield Can
Fence)
SL 5 Replace
V2475 or V2471
SL 4 Escalate
Yes Replace
S2415
No
No
SL 5 Replace
V2482
SL 4 Escalate
Camera Play and Mode (REC) Button Problems
3.8 Volt DC
at MP 160 (C2473)
SL 5 Replace
N2000
SL 4 Escalate
No
Replace
X2410 Yes
Connect: VBATT and DCIO/SEPI
Restart the Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Keypad LED
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: Numeric Key Foil to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Keypad LED
If Keypad LED is working on the TRS Fixture
then Replace Numeric Key Foil
If not then continue with the
Numeric Keypad LED Problems TRS guide
Disconnect:
VBATT and DCIO/SEPI
Disconnect:
Numeric Key Foil
Max 1 Ohm
between MP 74
(R4401) and MP 72
(C4401)
SL 5 Replace
L4400
SL 4 Escalate
No
Yes
5 Volt DC at
MP 56 (TP4400) No Replace N4400
Yes
Fault Trace SW
Deactivate:
Keypad LED
Numeric Keypad LED Problems
SEMC Troubleshooting Manual
14 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Navigation Keypad LED Problems
TROUBLESHOOTING
- Auto Focus LED Problems
Replace
X4200
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: PBA Key Flex Flip and Slider FPC Assy
to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Keypad LED
If Navigation Keypad LED is working on the TRS Fixture
then Replace
PBA Key Flex Flip or Slider FPC Assy
If not then continue with the
Navigation Keypad LED Problems TRS guide
1: Cut the Shield Can Fence around the N4000, be very careful
to avoid component damage.
2: Use TRS Fixture
Connect: PBA Key Flex Flip and Slider FPC Assy to the PBA
Connect: VBATT and DCIO/SEPI
3: Restart the Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Keypad LED
Disconnect:
VBATT and DCIO/SEPI
Remove the PBA from the TRS Fixture
Max 1 Ohm
between MP 74
(R4401) and MP 72
(C4401)
SL 5 Replace
L4400
SL 4 Escalate
No
Yes
5 Volt DC at
MP 56 (TP4400) No
Replace
N4400
Yes
1.7V – 3V DC at
MP 78 (R4403), MP 77
(R4404), MP 75 (R4405)
and MP 79 (R4406)
NoYes
Navigation Keypad LED Problems
1.4V - 1.5V DC
at MP 93 (TP4401)
when Auto Focus LED
is Activated
No
Yes
Replace
N4400
5 Volt DC at
MP 56 (TP4400) when
Auto Focus LED is
Activated
YesNo
Is the
Problem solved
SL 5 Replace
N2010
SL 4 Escalate
No
Replace
X4400
Yes
Connect: VBATT and DCIO/SEPI
Connect: Flash Complete to the PBA
Restart the Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Auto Focus LED
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: Flash Complete to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Auto Focus LED
If Auto Focus LED is working on the TRS Fixture
then Replace Flash Complete
If not then continue with the
Auto Focus LED Problems TRS guide
Max 1 Ohm
between MP 74
(R4401) and
MP 72 (C4401)
SL 5 Replace
L4400
SL 4 Escalate
No
Yes
Disconnect:
VBATT and DCIO/SEPI
SL 4 Replace
N4400
SL 5 Replace
L4401
Claim Component
N4400
Auto Focus LED Problems
SEMC Troubleshooting Manual
15 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Back Side LED Problems
TROUBLESHOOTING
- Tally LED Problems
SL 4 Replace
X4400
SL 5 Replace
N2000
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: Flash Complete to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Back-Side LED
If the Back-Side LED is working on the TRS Fixture
then Replace Flash Complete
If not then continue with the
Back-Side LED Problems TRS guide
Disconnect:
VBATT and DCIO/SEPI
Disconnect:
Flash Complete from the PBA
Connect: VBATT and DCIO/SEPI
Restart Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Back-Side LED
5 Volt DC at
MP 56 (TP4400) when
Back-Side LED
is Activated
No Replace
N4400
Yes
Max
1 Ohm between
MP 74 (R4401) and
MP 72 (C4401)
SL 5 Replace
L4400
SL 4 Escalate
No
Yes
Back-Side LED Problems
5 Volt DC
at MP 56 (TP4400)
Yes
Replace
N4400
Connect: VBATT and DCIO/SEPI
Restart the Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Tally LED
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: Flash Complete to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Tally LED
If Tally LED is working on the TRS Fixture
then Replace Flash Complete
If not continue with the
Tally LED Problems TRS guide
Max 1 Ohm
between
MP 74 (R4401) and
MP 72 (C4401)
SL 5 Replace
L4400
SL 4 Escalate
No
Yes
Disconnect:
VBATT and DCIO/SEPI
1.8 Volt DC
at MP 134
(V4400_Pin 1)
No
Is
any of
MP 134 (V4400_Pin 1)
and MP 148 (V4400_Pin 3)
Short circuit to
PBA GND (Shield
Can Fence)
No
Replace
N2410 No
SL 5 Replace
V4400
SL 4 Escalate
Yes
Fault Trace SW:
Deactivate
Tally LED
Yes
2V – 2.5 Volt DC
at MP 148
(V4400_Pin 3)
No
SL 5 Replace
V4400
SL 4 Escalate
Fault Trace SW:
Activate
Tally LED
Yes
0 Volt DC
at MP 148
(V4400_Pin 3)
Replace
X4400 Yes
SL 5 Replace
V4400
SL 4 Escalate
No
Tally LED Problems
SEMC Troubleshooting Manual
16 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Camera Snap Button LED
TROUBLESHOOTING
- Camera Navigation LED Problems
0 Volt DC
at MP 161 (C2474)
when the Camera LED
is Activated
SL 5 Replace
N2000
SL 4 Escalate
No
Replace
X2410 Yes
Connect: VBATT and DCIO/SEPI
Restart the Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Camera LED
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: Numeric Key Foil to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Camera LED
If Camera Snap Button LED is working on the TRS Fixture
then Replace Numeric Key Foil
If not then continue with the
Camera Snap Button LED Problems TRS guide
Disconnect:
VBATT and DCIO/SEPI
Disconnect:
Numeric Key Foil
Max
1 Ohm
between
MP 74 (R4401) and
MP 72 (C4401)
SL 5 Replace
L4400
SL 4 Escalate
No
Yes
5 Volt DC at
MP 56 (TP4400) when
the Camera LED is
Activated
No Replace
N4400
Yes
Camera Snap Button LED Problems
Connect: VBATT and DCIO/SEPI
Restart the Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Camera LED
No
Replace
X4200
Yes
0 Volt DC
at MP 92 (C4215) and
MP 86 (C4217) when
Camera LED is
Activated
0 Volt DC
at MP 89 (C4218)
when Camera LED is
Activated
SL 5 Replace
N2000
SL 4 Escalate
Yes
SL 5 Replace
V4208
SL 4 Escalate
No
Is
the Camera
Navigation LED
Problem solved
SL 5 Replace
N2000
SL 4 Escalate
No
Claim Component
V4208
Yes
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: PBA Key Flex Flip and Slider FPC Assy
to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Camera LED
If Camera Navigation LEDs is working on the TRS Fixture
then Replace
PBA Key Flex Flip or Slider FPC Assy
If not then continue with
Camera Navigation LED Problems TRS guide
Disconnect:
VBATT and DCIO/SEPI
Disconnect:
PBA Key Flex Flip and Slider FPC Assy
from the PBA
Max 1 Ohm
between
MP 74 (R4401) and
MP 72 (C4401)
SL 5 Replace
L4400
SL 4 Escalate
NoYes
5 Volt DC at
MP 56 (TP4400) when
Camera LED is
Activated
Replace
N4400
No
Yes
Camera Navigation LED Problems
SEMC Troubleshooting Manual
17 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Trickle Charge LED Problems
TROUBLESHOOTING
- Xenon Flash Problems
START
Step 1:
Replace Flash Complete
and retest the Phone
If successful claim
Flash Complete
If not go to step 2.
Step 2:
Load ITP SW into the Phone
Use Dummy Battery connected to the
Power Supply Channel 1 (VBATT)
Connect: DCIO/SEPI
Use Fault Trace SW
Fault Trace SW
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Xenon Flash Test
No
Is the
Xenon Flash Test
Ok
Yes
Flash the Phone with
EMMA SUCR SW
Is the
Camera working
properly
Go to Camera
Problems TRS guide No
Use TRS Fixture
Connect:
Flash Complete and Camera 8MP to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW
Fault Trace SW
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Xenon Flash Test
Yes
Disconnect:
Flash Complete
1.8V – 2V DC
at MP 149 (R4304) No 1.8 Volt DC at MP 87 (R4303)
Replace
N2410
No
SL 5 Replace
N4300
SL 4 Escalate
Yes
Yes
Replace
X4400
Is the
Xenon Flash
Problem solved
SL 4 Replace
N2410
SL 5 Replace
N2010
No
Claim Component
X4400
Yes
Is
MP 133 (X4410)
connected to the PBA
GND (Shield Can
Fence)
No Replace
X4410
Yes
Xenon Flash Problems
START
Load ITP SW into the Phone
Use TRS Fixture
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW
Continue with the
Trickle Charge LED Problems TRS guide
Fault Trace SW
MMI
Misc
Init Screen Testing
Led and Backlight
Activate:
Charge LED
No Yes
1.8 Volt DC
at MP 118
(V4206_Anode)
SL 5 Replace
N2000
SL 4 Escalate
Replace
V4206
Trickle Charge LED Problems
SEMC Troubleshooting Manual
18 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Multimedia Combo Chip Problems
TROUBLESHOOTING
- Camera Problems
START
Load ITP SW into the Phone
Use Dummy Battery connected
to Power Supply Channel 1
(VBATT)
Connect: DCIO/SEPI
Use Fault Trace SW
Fault Trace SW
General
Selftest
Run N2500 Selftest
Is the
N2500 Selftest
Test result
0x0
Flash the Phone with
EMMA SUCR SW
Yes
1: Use TRS Fixture
Connect:
VBATT and DCIO/SEPI
2: Use Fault trace SW and go to:
MMI
Misc
Init Screen Testing
Activate:
Multimedia Chip
No
1.8 Volt DC
at MP 71 (SP2505
VIDCC_L1DET)
Yes
No
1.2 Volt DC
at MP 69 (ST2226
VDD_L1)
1.8 Volt DC
at MP 70 (R2215
VIDCC_L1_EN)
No Replace
N2500
No
SL 5 Replace
N2210
SL 4 Escalate
Yes
1.8 Volt DC
at MP 42 (ST2229
VSDR18)
Yes
1.8 Volt DC
at MP 67 (R2223
VIDCC_SDR_EN)
No Replace
N2500
No
SL 5 Replace
N2214
SL 4 Escalate
Yes
1.2 Volt DC
at MP 66 (ST2228
VDD_L0)
Yes
1.8 Volt DC
at MP 36 (C2104
PWRRSTn)
No SL 5 Replace
N2000
SL 4 Escalate
SL 4 Replace
N2212
SL 5 Replace
N2010
No
Yes
1.8 Volt DC
at MP 68 (R2502
VIDCC_RESn)
SL 5 Replace
N2010
SL 4 Escalate
No
Yes
Replace
N2500
26 MHZ
at MP 20 (ST2109
VIDCC_CLK)
Yes
No
SL 4 Replace
N2500
SL 5 Replace
N2102
SL 5 Replace
N2010 or N2000
SL 4 Escalate
Yes
Multimedia Combo Chip Problems
START
Step 1:
Replace Camera 8MP and retest the Phone
If successful claim Camera 8MP
If not go to step 2.
Step 2:
Use Dummy Battery connected to the Power Supply Channel 1 (VBATT)
Load ITP SW into the Phone
Connect: DCIO/SEPI
Use Fault Trace SW
MMI
Misc
Init Screen Testing
Activate:
Camera Test
No
Yes
Is the
Multimedia Combo
Chip Problems TRS
guide done
Go to Multimedia
Combo Chip
Problems TRS guide
Flash the Phone with
EMMA SUCR SW
Is the
Camera working
Properly
No
Yes
1.8 Volt DC
at MP 64 (R2210) and
MP 129 (N2206_Pin 6)
1: Use TRS Fixture
Connect: Camera 8MP to the PBA
Connect: VBATT and DCIO/SEPI
2: Use Fault trace SW and go to:
MMI, Misc, Init Screen Testing and Activate: Camera Test
Replace
N2500
NoYes
2.8 Volt DC
at MP 131 (TP2210
VCAMAF28)
No
Replace
N2205
1.8V DC at
MP 130 (TP2208
VCAMSD18) and
2.8V DC at MP 128 (TP2209
VCAMSA28)
Yes
Replace
N2206 No 1.8 Volt DC at
MP 54 (TP2206
VCAMIO18)
Yes No
1.2 Volt DC
at MP 132 (TP2207
VCAML12)
Yes
Replace
N2213
No
13 MHz at
MP 37 (ST2110
CAMSYSCLK)
Yes
SL 5 Replace
N2010
SL 4 Escalate
No
Deactivate Camera Test and go to:
Fault Trace SW
General, Selftest and Run N2500 Selftest
Yes
Is the
N2500 Selftest
Test result
0x0
No Yes
Is the any of
X4311, X4312, X4313,
X4314 or X4315
damaged
Replace
Faulty Component
Yes
Replace
X4300
No
SL 5 Replace
V2212
SL 4 Escalate
SL 4 Replace
N2500
SL 5 Replace
N2010
Camera Problems
SEMC Troubleshooting Manual
19 (124)

C905
1222-9526 rev. 1
TROUBLESHOOTING Camera Cover Detect Problems
TROUBLESHOOTING
- TV Out Problems
START
Step 1:
Replace Flash Complete
and retest the Phone
If successful claim Flash Complete
If not go to step 2.
Step 2:
Use TRS Fixture
Connect Flash Complete to the PBA
Connect: VBATT and DCIO/SEPI
Continue with the
Camera Cover Detect Problems TRS guide
NOTE !
Camera Cover Detect Switch is mounted on
Flash Complete
NoYes
1.8 Volt DC
at MP 41 (R4410)
when Camera Cover
Detect Switch is
Pressed-On
Replace
X4400
SL 5 Replace
N2010
SL 4 Escalate
Camera Cover Detect Problems
Is the
Display Backlights
Ok
Go to
Dispaly illumination
Problems TRS guide
No
Is the
Display
Ok
Yes
Go to
Display Problems
TRS guide
No
Yes
START
NOTE !
Be very careful when you cut the Shield Can Fence
around the N2700 component to avoid component damage
Step 1:
Flash the Phone with EMMA SUCR SW
If successful claim SW Flash
If not go to step 2.
Step 2:
Load ITP SW into the Phone
Use TRS Fixture
Connect:
PBA Key Flex Flip, Slider FPC Assy and Display to the PBA
Connect: VBATT and DCIO/SEPI
Use Fault Trace SW and go to:
MMI
Misc
Init Screen Testing
Display Pattern
Activate:
TV Test Pattern
No
Is the
MP X2405_Pin 7
Short circuit to the
PBA GND (Shield
Can Fence)
Yes Replace
V2414
1.8 Volt DC at
MP 61 (R2228) No
SL 5 Replace
N2010
SL 4 Escalate
No
1.5 Volt DC at
MP 18 (ST2232
VTV15)
Yes
Replace
N2209 No 1.8 Volt DC at
MP 17 (R2214
VTV30_EN)
Yes Replace
N2700
No
3 Volt DC at
MP 15 (ST2233
VTV30)
Yes
Replace
N2208
No
26 MHz at
MP 19 (ST2108
TV_CLK)
Yes
SL 4 Replace
N2410
SL 5 Replace
N2102
No
0.9V – 1V
Pk-Pk Pulses at
MP 14 (L2405)
Yes
Replace
N2700 No Disconnect:
VBATT and
DCIO/SEPI
Yes Is
R2443 = Max 0.5 Ohm Replace
R2443
No
Yes
Replace
X2405
Is the
TV OUT
Problem solved
Claim Component
X2405 Yes SL 5 Replace
N2010
SL 4 Escalate
TV OUT Problems
SEMC Troubleshooting Manual
20 (124)