Sony ILCE-9 User manual

SERVICE MANUAL
Sony Imaging Products & Solutions Inc.
US Model
Canadian Model
AEP Model
UK Model
Russian Model
E Model
Indian Model
Chinese Model
Korea Model
Tourist Model
INTERCHANGEABLE LENS DIGITAL CAMERA
© 2018.04
2018D33-1
9-896-817-33
Ver. 1.2 2018.04
ILCE-9
LEVEL 2
Note:
Be sure to keep your PC used for service and
checking of this unit always updated with the
latest version of your anti-virus software.
In case a virus affected unit was found during
service, contact your Service Headquarters.
SYSSET
2018/04/1801:20:10(GMT+09:00)

ILCE-9
2
Model information table
Model ILCE-9
Destination US, CND, E, KR AEP, UK, RU, E, IND, CH, JE
Color system NTSC PAL
Lens ––
• Abbreviation
CH : Chinese model
CND : Canadian model
IND : Indian model
JE : Tourist model
KR : Korea model
RU : Russian model
SPECIFICATIONS
Camera
[System]
Camera Type
Interchangeable Lens Digital Camera
Lens
Sony E-mount lens
[Image sensor]
Image format
35mm full frame (35.6mm ×
23.8mm), CMOS image sensor
Effective pixel number of camera
Approx. 24200000 pixels
Total pixel number of camera
Approx. 28300000 pixels
[SteadyShot]
System
In-camera sensor shift image
stabilization system
[Anti-Dust]
System
Charge protection coating on
optical filter and image sensor shift
mechanism
[Auto focus system]
Detection system
Phase detection system/Contrast
detection system
Sensitivity Range
–3EV to +20EV (at ISO 100
equivalent, F2.0)
AF illuminator
Approx. 0.3m to 3m (0.99ft.
to 9.8ft.) (When using an
FE 28-70 mm F3.5-5.6 OSS)
[Electronic viewfinder]
Type
Electronic viewfinder
Total number of dots
3686400dots
Frame coverage
100%
Magnification
Approx. 0.78× with 50mm lens at
infinity, –1m–1
Eye Point
Approx. 23mm from the eyepiece
and approx. 18.5mm from the
eyepiece frame at –1m–1 (CIPA
standard compliant)
Diopter Adjustment
–4.0m–1 to +3.0m–1
[Monitor]
LCD monitor
7.5cm (3.0 type) TFT drive, touch
panel
Total number of dots
1440000 dots
[Exposure control]
Metering method
1200-zone evaluative metering
Metering Range
–3EV to +20EV (at ISO 100 equivalent
with F2.0 lens)
Flash sync speed
1/250second (when using a flash
manufactured by Sony)
[Continuous shooting]
Continuous shooting speed
(when shooting with the electronic
shutter)
: Maximum of approx.20images
per second/ : Maximum of
approx.10images per second/ :
Maximum of approx.5images per
second
• Based on our measurement
conditions. The speed of
continuous shooting can be
slower, depending on the shooting
conditions.
[Recording format]
File format
JPEG (DCF Ver. 2.0, Exif Ver. 2.31, MPF
Baseline) compliant, RAW (Sony ARW
2.3 format)
Movie (XAVC S format)
MPEG-4 AVC/H.264 XAVC S ver.1.0
format compliant
Video: MPEG-4 AVC/H.264
Audio: LPCM 2ch (48kHz 16bit)
Movie (AVCHD format)
AVCHD format Ver. 2.0 compatible
Video: MPEG-4 AVC/H.264
Audio: Dolby Digital 2ch, equipped
with Dolby Digital Stereo Creator
• Manufactured under license from
Dolby Laboratories.
Movie (MP4 format)
Video: MPEG-4 AVC/H.264
Audio: MPEG-4 AAC-LC 2ch
[Recording media]
Memory Stick media, SD cards
[Slot]
SLOT 1
Slot for SD cards (UHS-I and UHS-II
compatible)
SLOT 2
Multi-slot for Memory Stick PRO Duo
media and SD cards (UHS-I
compatible)
Supports operations between two
memory cards.
[Input/output terminals]
Multi/Micro USB Terminal*
Hi-Speed USB (USB 2.0)
* Supports Micro USB compatible
devices.
HDMI
HDMI type D micro jack
¯(Microphone) terminal
3.5mm Stereo mini jack
(Headphones) terminal
3.5mm Stereo mini jack
LAN terminal
(Flash sync) terminal
[Power, general]
Battery pack
Rechargeable battery pack NP-FZ100
Power consumption (while shooting)
Using an FE 28-70 mm F3.5-5.6 OSS
When using the viewfinder:
Approx. 4.1W
When using the monitor:
Approx. 3.0W
[Others]
Microphone
Stereo
Speaker
Monaural
Exif Print
Compatible
DPOF
Compatible
PRINT Image Matching III
Compatible
Dimensions
Approx. 126.9mm × 95.6mm ×
63.0mm
(Approx. 5inches × 37/8inches ×
21/2inches) (W/H/D, excluding
protrusions)
Mass
Approx. 673g (1lb 7.7oz) (including
battery pack and SD card)
Approx. 588g (1lb 4.7oz) (body only)
Operating temperature
0°C to 40°C (32°F to 104°F)
Storage temperature
–20°C to +60°C (–4°F to +140°F)
[Wireless LAN]
Supported format
IEEE802.11b/g/n
Frequency band
2.4GHz
Security
WEP/WPA-PSK/WPA2-PSK
Connection method
Wi-Fi Protected Setup™ (WPS)/
Manual
Access method
Infrastructure mode
[NFC]
Tag type
NFC Forum Type 3 Tag compliant
[Bluetooth communications]
Bluetooth standard Ver. 4.1
Frequency band
2.4GHz
Model No. WW361847
Battery charger BC-QZ1
Input rating
AC 100V to 240V, 50Hz/60Hz,
0.38A
Output rating
DC 8.4V, 1.6A
AC Adaptor AC-UUD12/AC-UUE12
Power requirements
AC 100V to 240V, 50Hz/60Hz, 0.2A
Output voltage
DC 5V, 1.5A
Rechargeable battery pack
NP-FZ100
Nominal voltage
DC 7.2V
Design and specifications are subject
to change without notice.
Still images
(
when shooting with the
mechanical shutter): 1/8000second
to 30seconds, BULB
Movies: 1/8000second to 1/4second
(1/3EV step)
– 108060i-compatible devices:
up to 1/60second in AUTO mode
(up to 1/30second in Auto slow
shutter mode)
– 108050i-compatible devices:
up to 1/50second in AUTO mode
(up to 1/25second in Auto slow
shutter mode)
ISO sensitivity (Recommended
exposure index)
Still images: ISO 100 to ISO 51200
(Extended ISO: Minimum ISO 50,
maximum ISO 204800), [ISO AUTO]
(ISO 100 to ISO 6400, Maximum/
Minimum can be set.)
Movies: ISO 100 to ISO 51200
equivalent (Extended ISO: Minimum
ISO 100, maximum ISO 102400),
[ISO AUTO] (ISO 100 to ISO 6400
equivalent, Maximum/Minimum can
be set.)
Exposure compensation
±5.0EV (switchable between 1/3EV
and 1/2EV steps)
When using exposure compensation
dial: ±3.0 EV (1/3 EV step)
[Shutter]
Type
Electronically-controlled, vertical-
traverse, focal-plane type
Speed range
Still images (when shooting with the
electronic shutter): 1/32000 second*
to 30seconds (up to 1/8second in
continuous shooting)
* Available only in the M(Manual
Exposure) and S(Shutter Priority)
modes. For details, refer to the
SYSSET
2018/04/1801:20:10(GMT+09:00)

ILCE-9
3
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE WITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your
health and environment, and wastes resources.
Manage the chemicals carefully as follows.
• Store chemicals sealed in a specific place to prevent from expo-
sure to high temperature or direct sunlight.
• Avoid dividing chemicals into excessive numbers of small con-
tainers to reduce natural evaporation.
• Keep containers sealed to avoid natural evaporation when chemi-
cals are not in use.
• Avoid using chemicals as much as possible. When using chemi-
cals, divide only required amount to a small plate from the con-
tainer and use up it.
EXTERIOR PARTS
Be careful to the following points for plastic parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning
plastic parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use
paint thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a
plastic part.
Be careful not to tighten screws too much.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered
connections. Check the entire board surface for solder splashes
and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched”
or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors,
that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs
of deterioration. Point them out to the customer and recommend
their replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 350°C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
UNLEADED SOLDER
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350°C approximately.
If cannot control temperature, solder/unsolder at high temperature
for a short time.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone
to flow) than ordinary solder so use caution not to let
solder bridges occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder
and those for leaded solder so they are managed separately.
Mixing unleaded solder and leaded solder will cause detachment
phenomenon.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
SYSSET
2018/04/1801:20:10(GMT+09:00)

1-1
ILCE-9
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE
SY-1081 BOARD
Destination Data
When you replace to the repairing board, the written destination data
of repairing board also might be changed to original setting.
Start the Adjust manual in the Adjust station and execute the “Des-
tination Data Write”.
Restore Data
When you replace to the repairing board, get the data from the
former one.
Start the Adjust manual in theAdjust station and perform “RESTORE
DATA” to get the data.
The data getting for this model is as follows.
• Product ID & USB Serial Data
• WB Adjustment Data
• AORI Adjustment Data
• Eyepiece Detection Adjustment Data
• Imager DRA Data
USB Serial No. and Product ID
The unit is shipped after an ID (USB Serial No.) unique to each unit
and an ID (Product ID) unique to each model have been written.
These IDs have not been written in a new board for service, and
therefore they must be entered after the board replacement.
After the board has been replaced with a board for service, start the
Adjust manual in the Adjust station and execute the “Product ID &
USB Serial No. Input” and enter these IDs.
Note: A newly entered Product ID is not always equal to the ID before
board replacement. If the new ID differs from the previous ID, it
may cause a difference from the ID registered by the customer.
Imager DRA Data
• When the imager data is extracted from the set before the SY board
replacement, extract the imager data from the set before the SY
board replacement using [READ and SAVE (Imager DRA)] of
“Restore Data” in the DATA tab of the Adjust manual.
After the SY board has been replaced, write the data extracted from
the set before the SY board replacement in the set using “Imager
DRA Data Write” in the ADJUST tab of the Adjust manual.
• When the imager data is not extracted from the set before the SY
board replacement, consult with each Head Quarters.
Update of MAC Address and Device Address
When a board that contains Wi-Fi and Bluetooth has been replaced
or when replacing a board that contains the main IC (CPU), the IC’s
unique number (MAC address and device address) must be reloaded.
Perform the following procedure to reload the IC’s unique number
(MAC address and device address).
Note: Perform the following operations after all work has been done.
1. Download the latest-version Adjust manual.
2. Install the downloaded Adjust manual.
3. Start the Adjust manual, and execute “Wireless LAN Setting
(MAC Address)” on the ADJUST tab.
4. Perform the following operations for the unit to initialize.
[MENU] button →[ ] →[Reset Network Set.] →[OK]
5. Perform the following operations for the unit to display MAC
address.
[MENU] button →[ ] →[Wi-Fi Settings] →[Disp MAC Ad-
dress]
6. Confirm that the displayed MAC address has been updated.
7. Perform the following operations for the unit to display device
address.
[MENU] button →[ ] →[Bluetooth Settings] →[Disp Device
Address]
8. Confirm that the displayed device address has been updated.
Applicable parts
• SY-1081 BOARD, COMPLETE (SERVICE)
Note: The LOAD AND WRITE function in ADJUSTMENT DATA
BACKUP on the DATA tab in the Adjust manual overwrites all data
of the unit.
Therefore, the MAC address and device address updated during the
above procedure is also overwritten.
After the replacement and repair, the MAC address and device ad-
dress are changed, and thus the re-setting for connection devices is
required. Accordingly, download the Flyer of WLAN Reset (Flyer
of WLAN Reset_9834752[][].pdf) and print out it, and attach it to
the set when returning the set to customer.
SYSSET
2018/04/1801:20:10(GMT+09:00)

1-2E
ILCE-9
1-2. PRECAUTION FOR REPLACEMENT
OF THE MECHA DEVICE SERVICE
(IMAGER)
Capture the data to PC from CD-ROM supplied with the mecha
device service when it is ordered.
Write the captured data in the set using “Imager DRA Data Write”
in the ADJUST tab of the Adjust manual.
After all adjustment items have been completed, execute “Phase
Difference AF Check” on the SERVICE tab of the Adjust manual.
1-3. PRECAUTION FOR REPLACEMENT
OF THE MECHA DEVICE SERVICE
(GYRO SENSOR) OR THE GY-1014
BOARD
Adjustment values of each gyro sensor are stored on the SY board.
Therefore, when the mecha device service or the GY-1014 board has
been replaced, write the sensitivity values of gyro sensor.
When replacing mecha device service:
1. Read the sensitivity values of P and Y written on the gyro data
label of CD-ROM supplied with the mecha device service when
it is ordered, and memorize it.
Gyro Data
P Y
Gyro Data Label
P: Pitch Sensitivity Value
Y: Yaw Sensitivity Value
CD-ROM
Note: The Pitch/Yaw Sensitivity Value is written by 1-digit number.
2. After the mecha device service has been replaced, execute “Set
Gyro Sensor Data” on the ADJUST tab by using the Adjust
manual to write the adjustment values.
When replacing GY-1014 board:
1. Read the sensitivity values of P and Y written on the repair parts,
and memorize it.
SE7701
P Y
Direction mark
P: Pitch Sensitivity Value
Y: Yaw Sensitivity Value
GY-1014 BOARD
Note: The sensitivity value is written only on repair parts.
The Pitch/Yaw Sensitivity Value is written by 1-digit number.
2. After the GY-1014 board has been replaced, execute “Set Gyro
Sensor Data” on the ADJUST tab by using the Adjust manual to
write the adjustment values.
1-4. CHECKING THE Wi-Fi FUNCTION
Perform the following procedure to check the Wi-Fi function.
Required equipment: Windows personal computer with Wi-Fi
interface
1. Turn on the power of the unit.
2. Perform the following operations for the unit.
[MENU] button →[ ] →[Ctrl w/ Smartphone] →[ Connec-
tion Info.]
3. QR code is displayed.
4. Press the [ ] button and then a password for Wi-Fi connection
is displayed..
SSID DIRECT-XXXX:MODEL-NAME
Password XXXXXXXX
Device Name ILCE-XXXX
5. Confirm on the personal computer that the unit is detected as a
connectable wireless network.
6. To further confirm that the unit is connectable, connect the unit
to the personal computer and double-click the “current connec-
tion” from the icon displayed on the notice field, make sure that
the unit is displayed in the Wireless internet access column.
DIRECT-XXXX:MODEL-NAME
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-1
ILCE-9
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
NG
(The flexible board was plugged in
crooked.)
NG
(The flexible board was not plugged in
completely.)
Flexible
Board Flexible
Board
Connector Connector
Reference
line
Flexible
Board
Connector Connector
Flexible
Board
Reference
line
Connector Connector
Flexible
Board
Flexible
Board
Reference
line
Fig. 1 Fig. 2 Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
Holder
Connector Flexible Board
A
AHolder
Insulation side
Connector Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
2. DISASSEMBLY & ASSEMBLY
Display Use Part No.
B-40 Adhesive bond (B-40) J-6082-614-A
G-85 Grease (G-85) J-6082-626-A
SERVICE TOOLS
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-2
ILCE-9
2-1. CONSTITUTION DIAGRAM
anti shake unit
front cover block
MB charge unit
shutter unit (AFE-3379)
MB N frame block
NFC base block
jack base (front) block
SY main frame block
SY-1081 board block
FP-2376 flexible board
SY heat sink assy
top cover block
VF block
bottom frame block
jack base (rear) block
rear cover block
bottom cover
front grip rubber
LCD panel block
BT block
grip base block
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-3
ILCE-9
2-2. DISASSEMBLY
• Disassembled in the order shown in the flowchart below.
2-2-1. DISASSEMBLY FLOW
MAIN UNIT
2-2-26. IM IMAGER BLOCK,
TEX-5300
(Page 2-21)
2-2-28. MB CHARGE UNIT,
SHUTTER UNIT (AFE-3379)
(Page 2-22)
2-2-16. TOP L JOINT PLATE ASSY,
2 STEP DIAL ASSY
(Page 2-14)
2-2-34. MB N PLATE A,
MB N PLATE SP
(Page 2-26)
2-2-36. CONTACT BLOCK
(Page 2-27)
2-2-35. MB LL BUTTON BLOCK
(Page 2-26)
2-2-29. MB N FRAME BLOCK
(Page 2-23)
2-2-33. BT BLOCK
(Page 2-25)
2-2-32. NFC BASE BLOCK
(Page 2-24)
2-2-31. JACK BASE (FRONT) BLOCK
(Page 2-24)
2-2-30. LOUDSPEAKER (1.0 cm) BLOCK
(Page 2-23)
2-2-27. SHUTTER BLOCK
(Page 2-22)
2-2-25. ANTI SHAKE UNIT
(Page 2-20)
2-2-24. SY MAIN FRAME BLOCK
(Page 2-20)
2-2-23. SY-1081 BOARD BLOCK
(Page 2-19)
2-2-22. FP-2376 FLEXIBLE BOARD
(Page 2-18)
2-2-21. SY HEAT SINK ASSY
(Page 2-18)
2-2-9. TOP COVER BLOCK
(Page 2-8)
2-2-8. VF BLOCK
(Page 2-7)
2-2-7. BOTTOM FRAME BLOCK
(Page 2-7)
2-2-6. JACK BASE (REAR) BLOCK
(Page 2-6)
2-2-4. REAR COVER BLOCK
(Page 2-5)
2-2-3. BOTTOM COVER
(Page 2-4)
2-2-2. FRONT GRIP RUBBER
(Page 2-4)
2-2-5. LCD PANEL BLOCK
(Page 2-6)
2-2-15. MD DIAL ASSY,
CONTROL SWITCH BLOCK
(EV79900)
(Page 2-13)
2-2-10. GY-1008 BOARD
(Page 2-9)
2-2-11. CNT DIAL (R) ASSY
(Page 2-10)
2-2-12. CONTROL DIAL (F) ASSY
(Page 2-10)
2-2-13. RL BLOCK-1
(Page 2-11)
2-2-17. EVF PROTECTOR
(Page 2-15)
2-2-18. SH FPC BASE BLOCK
(Page 2-16)
2-2-19. SH-1018 FLEXIBLE BOARD
(Page 2-16)
2-2-20. MIS-2003 FLEXIBLE BOARD
(Page 2-17)
2-2-14. RL BLOCK-2
(Page 2-12)
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-4
ILCE-9
Note: Disassemble in the order indicated by the numbers assigned to the parts in the figures such as 1.
2-2-2. FRONT GRIP RUBBER
top side
front side
3NFC performance
adhesive
4NFC performance
sheet
1front grip rubber
2adhesive sheets
2-2-3. BOTTOM COVER
front side
bottom side
1eight screws (M1.7 u4)
2bottom cover
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-5
ILCE-9
2-2-4. REAR COVER BLOCK
qd Lift up the rear cover block
in the direction of the arrow.
bottom side
top side
top side
2screw
(BTITE (1.4 u5 (CH)))
1eye cup assy
qa Open the media lid.
7Open three lids.
5Open the LCD panel.
3CV diopter adjust dial
rear side
rear side
rear side
qj rear cover block
qh JK lid
qg UH lid
0screw (M1.7 u4)
6screw (M1.7 u2.5)
4four screws (M1.7 u4)
qs two screws (M1.7 u4)
8three screws (M1.7 u4)
9two screws (M1.7 u3)
qf RS-1009 flexible
board
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-6
ILCE-9
2-2-5. LCD PANEL BLOCK
2-2-6. JACK BASE (REAR) BLOCK
LC drop cushion
5Draw the LC-1035 flexible board out of the hole.
4two screws
(P2 M1.7 u2.5)
4two screws
(P2 M1.7 u2.5)
top side
front side
6LCD panel block
3Peel off the narrow area
of the LC drop cushion.
1Peel off the wide area
of the LC drop cushion.
2LC-1035 flexible board
– Front view –
3jack base (rear) block
bottom side
rear side
2Remove the jack base (rear) block
in the direction of the arrow.
1Lean the jack base (rear) block
in the direction of the arrow.
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-7
ILCE-9
2-2-7. BOTTOM FRAME BLOCK
2-2-8. VF BLOCK
2Lift up the bottom frame block in
the direction of the arrow.
3bottom frame block
bottom side
rear side
1screw (M1.7 u2.5)
bottom side
rear side
2EVF flexible board
1ES-1003 flexible board
4VF block
3two hooks
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-8
ILCE-9
2-2-9. TOP COVER BLOCK
7top cover block
6two screws (M1.7 u2.5)
3two screws (M1.7 u4)
5screw (M1.7 u4)
3screw (M1.7 u4)
2SH-1018 flexible board 1RL-1049 flexible board
3screw (M1.7 u4)
4Open the battery lid.
– Rear view –
rear side
top side
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-9
ILCE-9
2-2-10. GY-1008 BOARD
bottom side
rear side
1screw (M1.7 u5)
2screw (M1.7 u2.5)
7GY-1008 board block
5Lift up the GY-1008 board block.
6RL-1049 flexible board
rear side
– Bottom view –
4hook 3boss
3boss
top side
rear side
0GY-1008 board
9gyro cushion (T)
8gyro (R) holder block
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-10
ILCE-9
2-2-11. CNT DIAL (R) ASSY
1screw (M1.7 u5)
bottom side
rear side
4boss
3Turn over the flexible board.
5CNT dial (R) block
8CNT dial (R) assy
7drop protection
R sheet 6protection
SP cushion
6protection SP cushion
2dial (R) hold plate
top side
2-2-12. CONTROL DIAL (F) ASSY
1two screws (M1.7 u2.5)
bottom side
rear side
2control dial (F) block
4control dial (F) ass
y
3drop protection F sheet
top side
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-11
ILCE-9
2-2-13. RL BLOCK-1
• Continued on 2-2-14 (page 2-12).
4screw (M1.7 u2.5)
3screw (M1.7 u3)
8Draw the flexible board out of the hole.
Note 2: Take care not to damage
the flexible board.
1Turn the switch to "OFF".
rear side
– Bottom view –
Note 1: Do not touch this part.
2hook
6three screws (M1.7 u2.5)
5control switch block (EV79900)
flexible board
bottom side
rear side
Note 1: Do not touch this part.
7Draw the LED part out of the hole.
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-12
ILCE-9
2-2-14. RL BLOCK-2
6two screws (M1.7 u2.5)
6screw (M1.7 u2.5)
7RL block
Note: Do not touch this part.
bottom side
1two screws (M1.7 u5)
2screw (M1.7 u4)
rear side
4boss
5eyelet (G) assy
3eyelet plate (G)
– Bottom view –
9control switch block (RL79900)
8three solders
RL block
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-13
ILCE-9
2-2-15. MD DIAL ASSY, CONTROL SWITCH BLOCK (EV79900)
3two screws (M1.7 u2.5)
5control switch block
(EV79900)
1two tapping screws (1.7 u4) (CH)
4Draw the flexible board out of the hole.
Note: Take care not to damage
the flexible board.
bottom side
2MD dial assy
rear side
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-14
ILCE-9
2-2-16. TOP L JOINT PLATE ASSY, 2 STEP DIAL ASSY
2two screws (0+Z M1.7 u4 SG (SPIN))
qg 2 step dial assy
6three screws (M1.7 u4)
5screw (M1.7 u2.5)
4eyelet (L) assy
qd AM dial lock button
qs AFMF lock spring
qa top L joint plate assy8two shafts
qf two tapping screws (1.7 u4) (CH)
3boss
front side
– Bottom view –
bottom side
rear side
0three hooks
9two hooks
bottom side
1tape AS (9 u14 mm)
7Lift up the top L joint plate block
in the direction of the arrow.
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)

2-15
ILCE-9
2-2-17. EVF PROTECTOR
1two screws (M1.7 u4)
3hook
2boss bottom side
7two tapping screws (1.7 u4) (CH)
qs EVF protector
6hook
5boss
front side
0boss
9adhesive
tape
8Lift up the EVF protector
in the direction of the arrow.
qa Draw the flexible board out of the hole.
Note: Take care not to damage
the flexible board.
4adhesive tape
Ver. 1.2
SYSSET
2018/04/1801:20:10(GMT+09:00)