Sony Dvp-ns700p - cd/dvd player User manual

SERVICE MANUAL

US Model

Canadian Model

CD/DVD PLAYER

SPECIFICATIONS

DVP-NS700P

RMT-D129A

System

Laser Semiconductor laser

Signal format system NTSC

Audio characteristics

Frequency response DVD (PCM 96 kHz): 2 Hz to 44 kHz (±1.0 dB)

DVD (PCM 48 kHz): 2 Hz to 22 kHz (±0.5 dB)

CD: 2 Hz to 20 kHz (±0.5 dB)

Signal-to-noise ratio (S/N ratio) 115 dB (LINE OUT L/R (AUDIO) 1/2 jacks only)

Harmonic distortion 0.003 %

Dynamic range DVD: 103 dB

CD: 99 dB

Wow and flutter Less than detected value (±0.001% W PEAK)

The signals from LINE OUT L/R (AUDIO) 1/2 jacks are measured. When you play PCM sound tracks with

a 96 kHz sampling frequency, the output signals from the DIGITAL OUT (COAXIAL and OPTICAL) jacks

are converted to 48 kHz sampling frequency.

Outputs

General

Power requirements 120V AC, 60 Hz

Power consumption 15 W

Dimensions (approx.) 430 ×74 ×256 mm (17 ×3 ×10

in.) (w/h/d) incl. projecting parts

Mass (approx.) 2.7 kg (5 lb)

Operating temperature 5 °C to 35 °C (41 °F to 95 °F)

Operating humidity 25 % to 80 %

Supplied accessories

Specifications and design are subject to change without notice.

ENERGY

STAR

Ris a U.S. registered mark. As an

ENERGY

STAR

RPartner, Sony Corporation

has determined that this product meets the

ENERGY

STAR

Rguidelines for energy efficiency.

Jack name Jack type Maximum output level Load impedance

LINE OUT L/R (AUDIO) (1/2) Phono jack 2 Vrms (at 50 kilohms) Over 10 kilohms

DIGITAL OUT (OPTICAL) Optical output jack -18 dBm Wave length: 660 nm

DIGITAL OUT (COAXIAL) Phono jack 0.5 Vp-p 75 ohms terminated

LINE OUT (VIDEO) (1/2) Phono jack 1.0 Vp-p 75 ohms, sync negative

S VIDEO OUT (1/2) 4-pin mini DIN Luminance signal: 1.0 Vp-p

Color signal: 0.286 Vp-p 75 ohms, sync negative

75 ohms terminated

COMPONENT VIDEO

OUT(Y, P

, P

)Phono jack Y: 1.0 Vp-p

, P

: 0.7 Vp-p 75 ohms, sync negative

75 ohms

Check that you have the following items:

•Audio/video cord (pinplug ×3 ypinplug ×3) (1)

•Remote commander (remote) RMT-D129A (1)

•Size AA (R6) batteries (2)

•Component video cord (pinplug ×3 ypinplug ×3) (1)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 2 –

WARNING!!

WHEN SERVICING, DO NOT APPROACH THE LASER

EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS

NECESSARY TO CONFIRM LASER BEAM EMISSION,

BE SURE TO OBSERVE FROM A DISTANCE OF

MORE THAN 25 cm FROM THE SURFACE OF THE

OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. CAUTION

Use of controls or adjustments or performance of procedures

other than those specified herein may result in hazardous ra-

diation exposure.

ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0

SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE

DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ

DE FONCTIONNEMENT. NE REMPLACER CES COM-

POSANTS QUE PAR DES PIÈCES SONY DONT LES

NUMÉROS SONT DONNÉS DANS CE MANUEL OU

DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0OR DOTTED

LINE WITH MARK 0ON THE SCHEMATIC DIAGRAMS

AND IN THE PARTS LIST ARE CRITICAL TO SAFE

OPERATION. REPLACE THESE COMPONENTS WITH

SONY PARTS WHOSE PART NUMBERS APPEAR AS

SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-

LISHED BY SONY.

CAUTION:

The use of optical instrument with this product will increase eye

hazard.

Fig. A. Using an AC voltmeter to check AC leakage.

1.5 k

Ω

0.15 µF

voltmeter

(0.75 V)

To Exposed Metal

Parts on Set

Earth Ground

LEAKAGETEST

The AC leakage from any exposed metal part to earth ground

and from all exposed metal parts to any exposed metal part having

a return to chassis, must not exceed 0.5 mA (500 microamperes).

Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCA

WT-540A. Follow the manufacturers' instructions to use these

instruments.

2. A battery-operatedAC milliammeter. The Data Precision 245

digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of a

VOM or battery-operated AC voltmeter. The “limit” indica-

tion is 0.75V, so analog meters must have an accurate low-

voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-

amples of a passive VOM that is suitable. Nearly all battery

operated digital multimeters that have a 2VAC range are suit-

able. (See Fig. A)

1. Check the area of your repair for unsoldered or poorly-sol-

dered connections. Check the entire board surface for solder

splashes and bridges.

2. Check the interboard wiring to ensure that no wires are

“pinched” or contact high-wattage resistors.

3. Look for unauthorized replacement parts, particularly transis-

tors, that were installed during a previous repair. Point them

out to the customer and recommend their replacement.

4. Look for parts which, though functioning, show obvious signs

of deterioration. Point them out to the customer and recom-

mend their replacement.

5. Check the line cord for cracks and abrasion. Recommend the

replacement of any such line cord to the customer.

6. Check the B+ voltage to see it is at the values specified.

7. Check the antenna terminals, metal trim, “metallized” knobs,

screws, and all other exposed metal parts for AC leakage.

Check leakage as described below.

SAFETY CHECK-OUT

After correcting the original service problem, perform the following

safety checks before releasing the set to the customer:

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 3 –

TABLE OF CONTENTS

Section Title Page Section Title Page

Service Note ............................................................................ 4

1. GENERAL

Getting Started .............................................................. 1-3

Hookups ........................................................................ 1-4

Playing Discs ................................................................. 1-6

Searching for a Scene................................................... 1-9

Viewing Information About the Disc.............................. 1-10

Sound Adjustments ....................................................... 1-11

Enjoying Movies ............................................................ 1-12

Using Various Additional Functions .............................. 1-14

Settings and Adjustments ............................................. 1-16

Additional Information ................................................... 1-18

2. DISASSEMBLY

2-1. Case Removal ............................................................... 2-1

2-2. AV-58 Board Removal ................................................... 2-1

2-3. MB-100 Board Removal................................................ 2-1

2-4. Tray Cover Removal ...................................................... 2-1

2-5. Front Panel Removal..................................................... 2-2

2-6. Power Block Removal ................................................... 2-2

2-7. RM-85 Board Removal.................................................. 2-2

2-8. Mechanism Deck Removal ........................................... 2-2

2-9. IF-83 Board Removal .................................................... 2-3

2-10. Tray Removal................................................................. 2-3

2-11. Loading Motor (M001), MS-81 Board Removal............ 2-3

2-12. Optical Pick-up Removal............................................... 2-3

2-13. Internal Views ................................................................ 2-4

2-14. Circuit Boards Location ................................................. 2-5

3. BLOCK DIAGRAMS

3-1. Overall Block Diagram................................................... 3-1

3-2. RF/Servo Block Diagram............................................... 3-3

3-3. Signal Processor Block Diagram .................................. 3-5

3-4. System Control Block Diagram ..................................... 3-7

3-5. Video Block Diagram..................................................... 3-9

3-6. Audio Block Diagram ..................................................... 3-11

3-7. Interface Control Block Diagram ................................... 3-13

3-8. Power 1 Block Diagram ................................................. 3-15

3-9. Power 2 Block Diagram ................................................. 3-17

4. PRINTED WIRING BOARDS AND SCHEMATIC

DIAGRAMS

4-1. Frame Schematic Diagram............................................ 4-3

4-2. Printed Wiring Boards and Schematic Diagrams ......... 4-5

MS-81 (LOADING), RM-85

(REMOTE COMMANDER RECEIVER)

Printed Wiring Board and Schematic Diagram............. 4-5

MB-100 Printed Wiring Board ....................................... 4-7

MB-100 (RF AMP, SERVO) Schematic Diagram.......... 4-11

MB-100 (ARP, SERVO DSP) Schematic Diagram........ 4-13

MB-100 (AV DECODER) Schematic Diagram.............. 4-15

MB-100 (BNR) Schematic Diagram .............................. 4-17

MB-100 (DRIVE) Schematic Diagram .......................... 4-19

MB-100 (SYSTEM CONTROL)

Schematic Diagram ....................................................... 4-21

MB-100 (CLOCK GENERATOR)

Schematic Diagram ....................................................... 4-23

MB-100 (AUDIO DSP, D/A CONVERTER)

Schematic Diagram ....................................................... 4-25

MB-100 (GATE ARRAY) Schematic Diagram............... 4-27

MB-100 (I/P CONVERTER) Schematic Diagram ......... 4-29

AV-58 Printed Wiring Board .......................................... 4-33

AV-58 (VIDEO BUFFER) Schematic Diagram.............. 4-35

AV-58 (AUDIO AMP) Schematic Diagram .................... 4-37

IF-83 Printed Wiring Board ........................................... 4-39

IF-83 (IF CON) Schematic Diagram ............................. 4-41

HS13S0U Printed Wiring Board.................................... 4-43

HS13S0U Schematic Diagram...................................... 4-45

5. IC PIN FUNCTION DESCRIPTION

5-1. System Control Pin Function

(MB-100 Board IC103) .................................................. 5-1

6. TEST MODE

6-1. General Description ...................................................... 6-1

6-2. Starting Test Mode ........................................................ 6-1

6-3. Syscon Diagnosis.......................................................... 6-1

6-4. Drive Auto Adjustment .................................................. 6-5

6-5. Drive Manual Operation ................................................ 6-7

6-6. Mecha Aging ................................................................. 6-10

6-7. Emergency History........................................................ 6-10

6-8. Version Information ....................................................... 6-11

6-9. Video Level Adjustment ................................................ 6-11

6-10. IF CON Self Diagnostic Function .................................. 6-11

6-11. Troubleshooting ............................................................. 6-18

7. ELECTRICAL ADJUSTMENT

7-1. Power Supply Check ..................................................... 7-1

1. HS13S0U Boards .......................................................... 7-1

7-2. Adjustment of Video System ......................................... 7-2

1. Video Level Adjustment ................................................ 7-2

2. Progressive Video Level Adjustment ............................ 7-2

3. Checking S Video Output S-Y....................................... 7-2

4. Checking S Video Output S-C....................................... 7-2

5. Checking ComponentVideo OutputY .......................... 7-3

6. Checking ComponentVideo Output B-Y ...................... 7-3

7. Checking ComponentVideo Output R-Y ...................... 7-3

7-3. Adjustment Related Parts Arrangement ....................... 7-4

8. REPAIR PARTS LIST

8-1. Exploded Views ............................................................. 8-1

8-1-1. Case Assembly ........................................................ 8-1

8-1-2. Chassis Assembly .................................................... 8-2

8-1-3. Mechanism Deck Assembly ..................................... 8-3

8-2. Electrical Parts List ....................................................... 8-4

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 4 –

SERVICE NOTE

1. DISASSEMBLY

• This set can be disassembled in the order shown below.

Set

Case

(Page 2-1)

AV-58 Board

(Page 2-1)

MB-100 Board

(Page 2-1)

Tray

(Page 2-3)

Loading Motor (M001),

MS-81 Board

(Page 2-3)

Optical Pick-up

(Page 2-3) IF-83 Board

(Page 2-3)

Mechanism Deck

(Page 2-2)

Tray Cover

(Page 2-1)

Power Block

(Page 2-2) RM-85 Board

(Page 2-2)

Front Panel

(Page 2-2)

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 5 –

1) Remove the case from the set. (Refer to 2-1)

2) Remove the rear panel as shown in Fig. 2.

Fig. 2

3) Remove the MB-100 board. (Refer to 2-3)

4) Set the rear panel as shown in Fig. 3.

Fig. 3

2. DISC REMOVAL PROCEDURE

(at POWER OFF)

1) Insert a tapering driver into the aperture of the unit bottom,

and move the lever of chuck cam in the direction of the arrow

A. (See Fig. 1)

2) Draw out the tray in the direction of the arrow B, and remove

a disc. (See Fig. 1)

Fig. 1

3. HOW TO SERVICE MB-100 BOARD

• Jig (J-6090-107-A) Extension cable

Tray

Lever of chuck cam

Aperture

CK-105 board

Stand

(with CK-106 Board)

Eight flexible flat cables

FFC 5P, FFC 9P, FFC 15P, FFC26 P,

FFC 9P (DVP-NS500P/NS700P),

FFC 15P (DVP-NS400D),

FFC 25P (EXCEPT DVP-NS300 J model),

FFC 29P (DVP-NS300 J model)

2Two connectors

(CN101, 202)

1Two flexible flat cables

(FMAV-003: CN102/FMA-029: CN203)

6Rear panel

3Screw (B3)

4Boss

5Boss

5Two connectors

(CN101, 202)

Rear panel

4Screw (B3)

3Boss

2Boss

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 6 –

5) Set the stand (with CK-106 board) as shown in Fig. 4.

Fig. 4

6) Set the CK-105 board as shown in Fig. 5.

Fig. 5

7) Set the four flexible flat cables as shown in Fig. 6.

Fig. 6

1MB-100 board

2Stand

(with CK-106 board)

3Connector (CN101)

4Two screws (B3)

4Connector (CN109)

1CK-105 board

3Claw

4Connector (FFC15P: CN110)

3Flexible flat cable

(FFC15P: CN201)

2Three connectors

(FFC26P: CN102/

FFC9P: CN104/

FFC5P: CN106)

1Three flexible flat cables

(FFC26P: CN201/

FFC9P: CN202/

FFC5P: CN402)

8) Set the MB-100 board as shown in Fig. 7, Fig. 8.

Fig. 7

Fig. 8

2Connector

(FFC9P: CN902)

4Connector

(FFC25P: CN801)

1Flexible flat cable

(FFC9P: CN102)

3Flexible flat cable

(FFC25P: CN203)

MB-100 board

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

– 7 –

5. CONNECTION OF SERVICE JIG

CK-105

Mechanism deck

IF-83

MB-100

AV-58

CK-106

(Stand)

B to B Connector 15P

FFC26P

(Used the set)

FFC 9P

(Used the set)

FFC 5P

(Used the set)

FFC26P

FFC 9P

FFC 5P

FFC15P

FFC9P FFC25P

CN101 CN102

CN103 CN104

CN105 CN106

CN201

CN202

CN402

CN109CN403 CN110 CN201

CN202

CN101

CN801

CN203

CN902

CN102

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-1

SECTION 1

GENERAL This section is extracted from instruction

manual (3-068-059-11).

DVP-NS700P

About this Manual

•Instructions in this manual describe the

controls on the remote. You can also use the

controls on the player if they have the same

or similar names as those on the remote.

•The meaning of the icons used in this

manual is described below:

This Player Can Play the

Following Discs

The “DVD VIDEO”logo is a trademark.

Your player has a region code printed on the

back of the unit and will only play DVDs

labeled with identical region codes.

DVDs labeled will also play on this

player.

If you try to play any other DVD, the

message “Playback prohibited by area

limitations.”will appear on the TV screen.

Depending on the DVD, no region code

indication may be labeled even though

playing the DVD is prohibited by area

restrictions.

The player cannot play the following discs:

•CD-ROMs (PHOTO CDs included)

•All CD-Rs other than music and VCD

format CD-Rs

•Data part of CD-Extras

•DVD-ROMs

•DVD Audio discs

•HD layer on SACDs

Also, the player cannot play the following

discs:

•A DVD with a different region code (page

79).

•A disc recorded in a color system other than

NTSC, such as PAL or SECAM (this player

conforms to the NTSC color system).

•A disc that has a non-standard shape (e.g.,

card, heart).

•A disc with paper or stickers on it.

•A disc that has the adhesive of cellophane

tape or a sticker still left on it.

Icon Meaning Icon Meaning

Functions

available in

DVD video

mode

Functions

available in

music CD

mode

Functions

available in

VIDEO CD

mode

convenient

features

Format of discs

DVD VIDEO

VIDEO CD

Music CD

Region code

Example of discs that the player

cannot play

ALL

MODEL NO.

DVP–XXXX

CD/DVD PLAYER

AC 00V00Hz

00W

NO.

SONY CORPORATION

MADE IN JAPAN 0-000-000-00

Region code

Note

Some CD-Rs or CD-RWs cannot be played on this

player depending upon the recording quality or

physical condition of the disc, or the characteristics of

the recording device.

Furthermore, the disc will not play if it has not been

correctly finalized. For more information, see the

operating instructions for the recording device.

Some playback operations of DVDs and

VIDEO CDs may be intentionally set by

software producers. Since this player plays

DVDs and VIDEO CDs according to the disc

contents the software producers designed,

some playback features may not be available.

Also, refer to the instructions supplied with

the DVDs or VIDEO CDs.

This product incorporates copyright

protection technology that is protected by

method claims of certain U.S. patents, other

intellectual property rights owned by

Macrovision Corporation, and other rights

owners. Use of this copyright protection

technology must be authorized by

Macrovision Corporation, and is intended for

home and other limited viewing uses only

unless otherwise authorized by Macrovision

Corporation. Reverse engineering or

disassembly is prohibited.

Notes about the Discs

On handling discs

•To keep the disc clean, handle the disc by its

edge. Do not touch the surface.

•Do not expose the disc to direct sunlight or

heat sources such as hot air ducts, or leave

it in a car parked in direct sunlight as the

temperature may rise considerably inside

the car.

•After playing, store the disc in its case.

On cleaning

•Before playing, clean the disc with a

cleaning cloth.

Wipe the disc from the center out.

•Do not use solvents such as benzine,

thinner, commercially available cleaners, or

anti-static spray intended for vinyl LPs.

Note on playback operations of

DVDs and VIDEO CDs

Copyrights

Index to Parts and Controls

For more information, refer to the pages indicated in parentheses.

APOWER switch/indicator (29)

2PROGRESSIVE indicator (70)

3Disc tray (29)

4A(open/close) button (29)

5./>(previous/next) buttons (30)

6C/X/x/c/ ENTER buttons (25)

7JOG button/indicator (40)

8TITLE button (32)

9DVD MENU button (32)

q; ORETURN button (33)

qa DISPLAY button (12)

qs Click shuttle (40)

qd x(stop) button (29)

qf X(pause) button (30)

qg H(play) button (29)

qh Front panel display (9)

qj SURROUND button/indicator (51)

qk BNR (Block Noise Reduction) button/

indicator (55)

ql (remote sensor) (15)

Front Panel

POWER

OFF

SURROUND

BNR

PROGRESSIVE SCAN

TITLE

DVD MENU

RETURN

DISPLAY

JOG

PUSH

ENTER

When playing back a DVD

When playing back a VIDEO CD (PBC)

When playing back a CD or VIDEO CD (without PBC)

Front Panel Display

DVD

PGM SHUFFLE TITLE CHAP HOUR MIN SEC

DTS ANGLE REPEAT1

A-B

Digital

Playing time (45)

Disc type Playing status

Current chapter (45)

Current audio

signal (50)

Lights up when you can change

the angle (53)

Current play

mode (34) Current title (45)

VIDEOCD

PBC

MIN SEC

A-B

Playing status

Current play mode

(34)

Disc type

Current scene (45) Playing time (45)

Lights up when playing back a VIDEO CD with PBC (33)

VIDEOCD

PGM SHUFFLE TRACK INDEX MIN SEC

REPEAT1

A-B

Playing time (45)

Disc type

Playing status

Current track and

index (45)

Current play mode (34)

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-2

1DIGITAL OUT (COAXIAL) jack (22)

(23) (24)

2DIGITAL OUT (OPTICAL) jack (22)

(23) (24)

3LINE OUT L/R (AUDIO) 1/2 jacks (16)

(21) (22) (23)

4LINE OUT (VIDEO) 1/2 jacks (16) (18)

5S VIDEO OUT 1/2 jacks (18)

6COMPONENT VIDEO OUT jacks (18)

7VIDEO OUT SCAN SELECT switch

(70)

Rear Panel

COAXIAL OPTICAL

R– AUDIO 1 –L VIDEO 1

R– AUDIO 2 –L VIDEO 2

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

AZOPEN/CLOSE button (30)

BNumber buttons

CCLEAR button (34)

DANGLE button (53)

5AUDIO button (49)

6PROGRAM button (34)

7SHUFFLE button (36)

H./>PREV/NEXT buttons (30)

Ic/C SEARCH/STEP buttons

(39)

JHPLAY button (29)

KTITLE button (32)

LDISPLAY button (34)

MTV/DVD switch (64)

N[/1(on/standby) button (29)

OBNR (Block Noise Reduction) button

(55)

PTV/VIDEO button (64)

QVOL +/–buttons (64)

RENTER button

SSUBTITLE button (54)

TTIME/TEXT button (45)

UREPEAT button (36)

VINSTANT REPLAY button (30)

WSURROUND button (51)

X/ySCAN/SLOW buttons (39)

YXPAUSE button (30)

ZxSTOP button (29)

wj DVD MENU button (32)

wk C/X/x/cbuttons (25)

wl ENTER button (25)

e; ORETURN button (33)

Remote

1 2 3

4 5 6

7 8 9

Guide to the Control Menu Display

Use the Control Menu to select a function that you would like to use. The Control Menu display

appears when the DISPLAY button is pressed. For details, please refer to the page in parentheses.

List of Control Menu Items

Control Menu

OFF

2: FRENCH

3: SPANISH

1: ENGLISH

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

Select: Cancel:

SUBTITLE

ENTER RETURN

PLAY

1: ENGLISH

Currently playing chapter

number (Video CD: index

number) Playing time

Total number of chapters or indexes recorded

Currently playing title number

(Video CD/CD: track number)

Options

Current setting

Total number of titles or tracks recorded

Playback status

(N Playback, XPause, xStop, etc.)

Functionnameofselected

Control Menu item

Operation message

Icon of selected

Control Menu item

Control Menu items

Type of disc being

played back

TITLE (DVD only) (page 41)/

SCENE (only VIDEO CD in PBC

playback) (page 41)/TRACK (VIDEO CD

only) (page 41)

Selects the title (DVD), the scene (VIDEO CD

in PBC playback) or the track (VIDEO CD) to

be played.

CHAPTER (DVD only) (page

41)/INDEX (VIDEO CD only) (page 41)

Selects the chapter (DVD) or the index

(VIDEO CD) to be played.

TRACK (CD only) (page 41) Selects the track (CD) to be played.

INDEX (CD only) (page 41) Selects the index (CD) to be played.

TIME/TEXT (page 41) Checks the elapsed time and the remaining

playback time.

Input the time code for picture and music

searching.

Displays the DVD or the CD text.

AUDIO (page 49) Changes the audio setting.

SUBTITLE (DVD only) (page

54)

Displays the subtitles.

Changes the subtitle language.

ANGLE (DVD only) (page 53) Changes the angle.

TVS (TV Virtual Surround

Sound) (page 51)

Lets you enjoy surround sound effects by using

sound imaging to create virtual rear speakers

from the sound of your stereo TV’s internal

speakers.

ADVANCED (DVD only) (page

48)

Checks the information (bit rate or layer) on

the disc while playing a DVD.

CUSTOM PARENTAL

CONTROL (page 59)

Sets the disc to prohibit playing.

SETUP (page 67) QUICK Setup (page 25)

Use Quick Setup to choose the desired

language of the on screen display, the shape of

the TV screen, and the audio output.

CUSTOM Setup

In addition to the Quick Setup setting, you can

adjust the image and sound quality, Parental

Control, and other various settings.

RESET

Returns the settings in “SETUP”to the default

setting.

PROGRAM (page 34) Selects the title, the chapter, or the track to play

a disc in the order you want.

SHUFFLE (page 36) Plays the title, the chapter, or the track in

random order.

REPEAT (page 36) Plays the entire disc (all titles/all tracks)

repeatedly or one title/chapter/track

repeatedly.

A-B REPEAT (page 37) Specifies the parts you want to play repeatedly.

BNR (page 55) Adjusts the picture quality by reducing the

“block noise”or mosaic like patterns that

appear on your TV screen.

VIDEO EQUALIZER (DVD/

VIDEO CD only) (page 56)

Adjusts the video signal of the DVD or VIDEO

CD from the player. You can adjust each

element of the picture, such as the HUE and

BRIGHTNESS.

DIGITAL VIDEO ENHANCER

(DVD/VIDEO CD only) (page 58)

Exaggerates the outline of the image to

produce a sharper picture.

VIEWER (DVD/VIDEO CD only)

(page 43)

Divides the screen into 9 sub-screens to help

you find the scene you want quickly.

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-3

zEach time you press DISPLAY, the Control Menu display changes as follows:

You can display the Control Menu display 1 only during CD playback. The Control Menu items are different

depending on the disc.

zThe Control Menu icon indicator lights up in green twhen you select any item except

“OFF.”(“TVS,”“PROGRAM,”“SHUFFLE,”“REPEAT,”“A-B REPEAT,”“BNR,”“DIGITAL VIDEO

ENHANCER”only). The “ANGLE”indicator lights up in green only when the angles can be changed. The

“VIDEO EQUALIZER”indicator lights up in green when any setting other than “STANDARD”is selected.

Control Menu display 1

Control Menu display 2

(The items except the first three items from the top are changed to other items.)

ADVANCED display (Appears if you select any setting other than “OFF.”See page 48.)

Control Menu display off

Getting Started

Quick Overview

A quick overview presented in this chapter will give you enough information to start using the

player for your enjoyment. To use the surround sound features of this player, refer to “Hookups”

on page 18.

Note

You cannot connect this player to a TV that does not have a video input jack.

Be sure to turn off the power of each component before connecting.

Step 1: Unpacking

Check that you have the following items:

•Audio/video cord (pinplug ×3 ypinplug ×3) (1)

•Remote commander (remote) RMT-D129A (1)

•Size AA (R6) batteries (2)

•Component video cord (pinplug ×3 ypinplug ×3) (1)

Step 2: Inserting Batteries into the Remote

You can control the player using the supplied remote. Insert two size AA (R6) batteries by

matching the 3and #ends on the batteries to the markings inside the compartment. When using

the remote, point it at the remote sensor on the player.

Notes

•Do not leave the remote in an extremely hot or humid place.

•Do not drop any foreign object into the remote casing, particularly when replacing the batteries.

•Do not expose the remote sensor to direct light from the sun or a lighting apparatus. Doing so may cause a

malfunction.

•If you do not use the remote for an extended period of time, remove the batteries to avoid possible damage from

battery leakage and corrosion.

Step 3: TV Hookups

Connect the supplied audio/video cord and power cord in the order (1~3) shown below. Be

sure to connect the power cord last.

When connecting to a wide screen TV

Depending on the disc, the image may not fit your TV screen.

If you want to change the aspect ratio, please refer to page 69.

When connecting to a TV that accepts progressive (480p) format signals

You need to use the COMPONENT VIDEO OUT jacks to view progressive signals. Hook up

your TV using pattern Con page 18, and then run Quick Setup on page 25.

COAXIAL OPTICAL

R– AUDIO 1 –L VIDEO 1

R– AUDIO 2 –LVIDEO2

PCM/DTS/

DOLBY DIGITAL

DIGITALOUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

VIDEO

AUDIO

INPUT

(yellow)

(white)

(red)

R– AUDIO 2 –L VIDEO 2

LINE OUT

R– AUDIO 1 –L VIDEO 1

Power source

CD/DVD Player

Power source

l: Signal flow

to video input

to LINE OUT L/R

(AUDIO) 1

Audio/video

cord (supplied)

to audio input

to LINE OUT (VIDEO) 1

Getting Started

Step 4: Playing a Disc

1Turn on the TV.

2Switch the input selector on the TV to the player.

3Press POWER on the player.

4Press Aon the player to open the disc tray.

5Place the disc on the tray with the playback side facing down.

6Press H.

The disc tray closes and the player begins playing the disc.

After Step 6

Depending on the disc, a menu may be displayed on the TV screen. If so, select the item you want

from the menu and play the DVD (page 32) or VIDEO CD disc (page 33).

To stop playing

Press x.

To take out the disc

Press A.

To turn off the player

Press [/1on the remote. The player is set to standby mode and the power indicator lights up in

red. Press POWER on the player to turn off completely.

With the playback side facing down

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-4

Hookups

Hooking Up the Player

Follow Steps 1 to 4 to hook up and adjust the settings of the player.

Before you start, turn off the power, check that you have all of the supplied accessories, and insert

the batteries into the remote (page 15).

Notes

•Plug cords securely to prevent unwanted noise.

•Refer to the instructions supplied with the components to be connected.

Step 1: Connecting the Video Cords

Connect this player to your TV monitor, projector, or AV amplifier (receiver) using a video cord.

Select one of the patterns Athrough C, according to the input jack on your TV monitor,

projector, or AV amplifier (receiver). In order to view progressive signal (480p) pictures with a

compatible TV, projector, or monitor, you must use connection C.

COAXIAL OPTICAL

R– AUDIO 1 –L VIDEO 1

R– AUDIO 2 –L VIDEO 2

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

COMPONENT

VIDEO IN

AUDIO

VIDEO

INPUT

S VIDEO

CD/DVD player

TV, projector, or AV

amplifier (receiver)

l: Signal flow

Audio/video

cord (supplied)

(yellow)

(yellow) Component video

cord (supplied)

S VIDEO cord

(not supplied)

TV, projector, or AV

amplifier (receiver)

TV, projector, or AV

amplifier (receiver)

(green)

(blue)

(red)

(green)

(blue) (red)

Hookups

Connect the yellow plug of the audio/video cord (supplied) to the yellow (video) jacks. You will

enjoy standard quality images.

Use the red and white plugs to connect to the audio input jacks (page 21).

Connect the S VIDEO cord (not supplied). You will enjoy standard quality images.

Connect the component via the COMPONENT VIDEO OUT jacks using the component video

cord (supplied) or three video cords (not supplied) of the same kind and length. You will enjoy

accurate color reproduction and high quality images. If your TV accepts progressive (480p)

format signals, you must use this connection and set “COMPONENT OUT”to

“PROGRESSIVE”in “SCREEN SETUP”(page 69).

Notes

•Do not connect the player to a VCR if you pass the player signals via the VCR. You may not receive a clear image

on the TV screen.

•Consumers should note that not all high definition television sets are fully compatible with this product and may

cause artifacts to be displayed in the picture. In the case of 480 progressive scan picture problems, it is

recommended that the user switch the connection to the standard definition output. If there are questions regarding

your Sony TV set’s compatibility with this model 480p DVD player, please contact our customer service center.

If you are connecting to a video input jack

BIf you are connecting to an S VIDEO input jack

CIf you are connecting to a monitor, projector, or AV amplifier (receiver) having

component video input jacks (Y, P

, P

)

Yellow (Video)

White (L)

Red (R)

Yellow (Video)

White (L)

Red (R)

Green

Blue

Red

Green

Blue

Red

VCR

CD/DVD player TV

Connect directly

Step 2: Connecting the Audio Cords

Refer to the chart below to select the connection that best suits your system. The surround effects

you will enjoy depend on the connections and components you use.

Select one of the following connections, through .

* Manufactured under license from Dolby Laboratories. “Dolby,”“Pro Logic,”and the double-D symbol are

reserved.

** “DTS”is a registered trademark of Digital Theater Systems, Inc.

Select a connection

Connection Components to be connected

(page 21)

•

TV (stereo)

(page 22)

•

Stereo amplifier (receiver)

(having L and R audio input jacks only, or having a digital input jack)

•

2 speakers

(front L and R)

(page 22)

•

MD deck/DAT deck

(page 23)

•

AV amplifier (receiver) with a Dolby

Surround (Pro Logic) decoder

(having L and R audio input jacks only, or having a digital input jack)

•

3 speakers

(front L and R, and rear (monaural))

•

6 speakers

(front L and R, center, rear L and R, and subwoofer)

(page 24)

•

AV amplifier (receiver) having a Dolby Digital or DTS

decoder and a digital

input jack

•

6 speakers

(front L and R, rear L and R, center, and subwoofer)

A D

Hookups

This connection will use your TV speakers for sound.

xRecommended surround sound effects for this connection

•TVS DYNAMIC (page 51)

•TVS WIDE (page 51)

The yellow plug is used for video signals (page 18).

Connecting to your TV

COAXIAL OPTICAL

R– AUDIO 1 – L VIDEO 1

R– AUDIO 2 – L VIDEO 2

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

R– AUDIO 1 –L VIDEO 1

R– AUDIO 2 –L VIDEO 2

LINE OUT

l: Signal flow

CD/DVD player

Audio/video cord

(supplied)

(white)

(red)

(yellow)

to audio input

(white)

(red)

(yellow)

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-5

This connection will use your 2 front speakers connected to your stereo amplifier (receiver) for

sound. If the stereo amplifier (receiver) has audio input jacks L and R only, use . If the

amplifier (receiver) has a digital input jack, use . When connecting to an MD deck or a DAT

deck, use . In this case, you can also connect the player directly to the MD deck or DAT

deck without using your stereo amplifier (receiver).

xRecommended surround sound effects for the connection only

•TVS STANDARD (page 51)

In connection

, you can use the supplied audio/video cord instead of using a separate audio cord.

To realize better surround sound effects, make sure that your listening position is in between your speakers.

Note

If you select one of the TVS effects while playing a disc, no sound will come from your speakers with the connection.

Connecting to a stereo amplifier (receiver) and 2 speakers/Connecting to

an MD deck or DAT deck

B-1

B-2

B-1

B-2

COAXIAL OPTICAL

R– AUDIO 1 –L VIDEO 1

R– AUDIO 2 –L VIDEO 2

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

B-2 B-1

VIDEO 1

R– AUDIO 2 –L VIDEO 2

LINE OUT

R– AUDIO 1 –L

COAXIAL OPTICAL

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

l: Signal flow

CD/DVD player

Stereo amplifier (receiver)

MD deck/DAT deck

Front

(L)

Front

(R)

[Speakers]

(white)

(red)

(white) (red)

Coaxial digital

cord(notsupplied)

Stereo audio

cord

(not supplied)

Optical digital cord

(not supplied)

Remove jack cap

before connecting

to coaxial or optical digital input to audioinput

Hookups

This connection will allow you to enjoy the surround effects of the Pro Logic decoder on your

amplifier (receiver). If you have an AV amplifier (receiver) equipped with a Dolby Digital, or

DTS decoder, refer to page 24.

You can enjoy the Dolby Surround effects only when playing Dolby Surround audio or multi-

channel audio (Dolby Digital) discs.

Pro Logic uses a minimum of 3 speakers (front L and R, and rear (monaural)). The surround

effects are enhanced if 6 speakers (front L and R, center, rear L and R, and subwoofer) are used.

If your amplifier (receiver) has R and L audio input jacks only, use . If your amplifier

(receiver) has a digital input jack, use .

xRecommended surround sound effects using this connection with your amplifier (receiver)

•Dolby Surround (Pro Logic) (page 79)

For correct speaker setting location, please refer to the operating instructions of the amplifier (receiver).

∗

When connecting 6 speakers, replace the monaural rear speaker with a center speaker, 2 rear speakers and a

subwoofer.

Connecting to a Dolby Surround (Pro Logic) decoder amplifier (receiver) and

3 to 6 speakers

C-1

C-2

COAXIAL OPTICAL

R– AUDIO 1 –LVIDEO1

R– AUDIO 2 –L VIDEO 2

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

VIDEO 1

R– AUDIO 2 –L VIDEO 2

LINE OUT

R– AUDIO 1 –L

COAXIAL OPTICAL

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

C-2 C-1

CD/DVD player

Front

(R)

Front

(L)

Rear

(R)

Subwoofer

l: Signal flow

Dolby Surround amplifier (receiver)

center Rear*

(mono)

[Speakers]

Coaxial digital cord

(not supplied)

Stereo audio

cord

(not supplied)

Optical digital cord

(not supplied)

Remove jack cap

before connecting

to coaxial or optical digital input to audio input

(red)

(white)

Rear

(L)

[Speakers]

(white)

(red)

continued

This connection will allow you to use the Dolby Digital, or DTS decoder function of your AV

amplifier (receiver). You are not able to enjoy the TVS sound effects of the player.

xRecommended surround sound effects using this connection with your amplifier (receiver)

•Dolby Digital (5.1ch) (page 79)

•DTS (5.1ch) (page 79)

To enhance the surround sound effects, refer to the operating instructions of the amplifier (receiver) for correct

speaker setting location.

Note

After you have completed the connection, be sure to set “DOLBY DIGITAL”to “DOLBY DIGITAL”(page 25).

If your AV amplifier (receiver) has a DTS decoder, set “DTS”to “ON”(page 25). Otherwise, no sound or a loud

noise will come from the speakers.

Connecting to an AV amplifier (receiver) with a digital input jack having a

Dolby Digital, or DTS decoder, and 6 speakers

COAXIAL OPTICAL

R– AUDIO 1 –LVIDEO1

R– AUDIO 2 –L VIDEO 2

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

SELECTABLE

INTERLACE

PROGRESSIVE

LINE OUT OUT

S VIDEO

VIDEO OUT

COMPONENT

SCAN SELECT

VIDEO OUT

COAXIAL OPTICAL

PCM/DTS/

DOLBY DIGITAL

DIGITAL OUT

Front

(R)

Rear

(R)

AV amplifier (receiver) with a decoder

Subwoofer Center

[Speakers] [Speakers]

CD/DVD player

l: Signal flow

Coaxial digital cord

(not supplied)

to optical digital input to coaxialdigital

input

Optical digital cord

(not supplied)

Remove jack cap

before connecting

Front

(L)

Rear

(L)

Hookups

Step 3: Connecting the Power Cord

Plug the player and TV power cords into an AC outlet.

Do not connect the power cord of your player to the “switched”power socket of an amplifier

(receiver). When you turn off the power of your amplifier (receiver), the menu setting for the

player such as Playback Memory may be lost.

Step 4: Quick Setup

Follow the steps below to make the minimum number of basic adjustments for using the player.

To skip an adjustment, press >. To return to the previous adjustment, press ..

1Turn on the TV.

2Switch the input selector on the TV to the player.

3Press POWER on the player and press [/1 on the remote.

“Press [ENTER] to run QUICK SETUP”appears at the bottom of the screen. If this message

does not appear, select “QUICK”under “SETUP”in the Control Menu to run Quick Setup (page

67).

4Press ENTER without inserting a disc.

The Setup Display for selecting the language used in the on-screen display appears.

1 2 3

4 5 6

7 8 9

./>X/x

POWER

./>

X/x

ENTER

[/1

LANGUAGE SETUP

OSD:

DVD MENU:

AUDIO:

SUBTITLE: FRENCH

ENGLISH

SPANISH

PORTUGUESE

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-6

5Press X/xto select a language.

The player uses the language selected here to display the DVD menu and subtitles as well.

6Press ENTER.

The Setup Display for selecting the aspect ratio of the TV to be connected appears.

7Press X/xto select the item.

8Press ENTER.

The Setup Display for selecting the type of video signal appears.

9Press X/xto select the item.

Select PROGRESSIVE only if you have made video connection C(page 18) and wish to

view progressive video signals.

q; Press ENTER.

The Setup Display for selecting the type of jack used to connect your amplifier (receiver)

appears.

TV Type You select Page

4:3 standard TV 4:3 LETTER BOX or 4:3 PAN

SCAN

A wide-screen TV or 4:3 standard TV with a

wide-screen mode

16:9 69

TV Type You select Page

Interlace format TV (standard TV) INTERLACE 70

Progressive format TV PROGRESSIVE 70

SCREEN SETUP

TV TYPE:

SCREEN SAVER:

BACKGROUND:

COMPONENT OUT: 16:9

4:3 LETTER BOX

4:3 PAN SCAN

MODE: AUTO

4:3 LETTER BOX

SCREEN SETUP

TV TYPE:

SCREEN SAVER

BACKGROUND:

4:3 LETTER BOX

JACKET PICTURE

COMPONENT OUT: INTERLACE

MODE: INTERLACE

PROGRESSIVE

YES

Is this player connected to an amplifier

(receiver) ? Select the type of jack you

are using.

LINE OUTPUT L/R (AUDIO)

DIGITAL OUTPUT

Hookups

qa Press X/xto select the item, then press ENTER.

•When “NO”or “LINE OUTPUT L/R (AUDIO)”is selected, Quick Setup is finished and

connections are complete.

•When “DIGITAL OUTPUT”is selected, the Setup Display for “DOLBY DIGITAL”

appears. Proceed to Step qs.

qs Press X/xto select the item.

Choose the item that matches the audio connection you selected in page 22 to 24 (

through ).

qd Press ENTER.

DTS is selected.

qf Press X/xto select the item.

Choose the item that matches the audio connection you selected in page 22 to 24 (

through ).

qg Press ENTER.

Quick Setup is finished. All connections and setup operations are complete.

Note

You can directly start Quick Setup only when you run it for the first time.

To run Quick Setup a second time, select “QUICK”under “SETUP”in the Control Menu (page 67).

Audio Cord Connection Type You select Page

D-PCM 75

DOLBY DIGITAL (only if the

amplifier/receiver has a Dolby

Digital decoder)

Audio Cord Connection Type You select Page

OFF 75

ON (only if the amplifier/receiver

has a DTS decoder)

AUDIO SETUP

AUDIO ATT:

AUDIO DRC:

DIGITAL OUT:

DOLBY DIGITAL:

DTS:

OFF

STANDARD

DOWNMIX: DOLBY SURROUND

DOLBY DIGITAL

D-PCM

B-2 C-2

AUDIO SETUP

AUDIO ATT:

AUDIO DRC:

DIGITAL OUT:

DOLBY DIGITAL:

DTS:

OFF

STANDARD

DOWNMIX: DOLBY SURROUND

D-PCM

OFF

B-2 C-2

continued

To enjoy the surround sound effects of this player or your amplifier (receiver), the following

items must be set as described below for the audio connection you selected in page 20 to 24

( through ). Each of these are the default settings and do not need to be adjusted when

you first connect the player. Refer to page 67 for using the Setup Display.

Audio Connection (page 20 to 24)

No additional settings are needed.

•If the sound distorts even when the volume is turned down, set “AUDIO ATT”to “ON”(page 74).

Enjoying the surround sound effects

Item You select Page

DOWNMIX DOLBY SURROUND 74

Item You select Page

DOWNMIX DOLBY SURROUND 74

DIGITAL OUT ON 75

B-1 C-1

B-2 C-2 D

Playing Discs

Depending on the DVD or VIDEO CD, some

operations may be different or restricted.

Refer to the operating instructions supplied

with your disc.

Turn on your TV.

Switch the input selector on the TV

to the player.

When using an amplifier (receiver)

Turn on the amplifier (receiver) and

select the appropriate channel.

Press POWER on the player.

The player enters standby mode and the

power indicator lights up in red.

Press Aon the player, and place a

disc on the disc tray.

The player automatically turns on and

the power indicator lights up in green.

Press H.

The disc tray closes, and the player

starts playback (continuous play).

Adjust the volume on the TV or the

amplifier (receiver).

After following Step 5

Depending on the disc, a menu may appear

on the TV screen. You can play the disc

interactively by following the instructions on

the menu. DVD (page 32), VIDEO CD (page

33).

To turn on the player

Press POWER on the player. The player

enters standby mode and the power indicator

lights up in red. Press [/1on the remote. The

player turns on and the power indicator lights

up in green. In standby mode, the player also

turns on by pressing Aon the player or by

pressing H.

To turn off the player

Press [/1on the remote. The player enters

standby mode and the power indicator lights

up in red. To turn off the player completely,

press POWER on the player. While playing a

disc, do not turn off the player by pressing

POWER. Doing so may cancel the menu

settings. When you turn off the player, first

press xto stop playback and then press [/1

on the remote.

POWER A

1 2 3

4 5 6

7 8 9

Power indicator

[/1

AUDIO

With the playback side facing down

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-7

Notes on playing DTS sound tracks on

a CD

•When playing DTS-encoded CDs,

excessive noise will be heard from the

analog stereo jacks. To avoid possible

damage to the audio system, the consumer

should take proper precautions when the

analog stereo jacks of the player are

connected to an amplification system. To

enjoy DTS Digital Surround™playback, an

external 5.1-channel decoder system must

be connected to the digital jacks of the

player.

•Set the sound to “STEREO”using the

AUDIO button when you play DTS sound

tracks on a CD (page 49).

•Do not play DTS sound tracks without first

connecting the player to an audio

component having a built-in DTS decoder.

The player outputs the DTS signal via the

DIGITAL OUT (OPTICAL and

COAXIAL) jacks even if “DTS”in

“AUDIO SETUP”is set to “OFF”in the

Setup Display (page 75), and may affect

your ears or cause your speakers to be

damaged.

Notes on playing DVDs with a DTS

sound track

•DTS audio signals are output only through

the DIGITAL OUT (OPTICAL and

COAXIAL) jacks.

•If you connect the player to audio

equipment without a DTS decoder, do not

set “DTS”to “ON”in “AUDIO SETUP”

(page 75). A loud noise may come out from

the speakers, affecting your ears or causing

the speakers to be damaged.

•When you play a DVD with DTS sound

tracks, set “DTS”to “ON”in “AUDIO

SETUP”(page 75).

The Instant Replay function is useful when you

want to review a scene or dialog that you missed.

Note

You may not be able to use the Instant Replay function

with some scenes.

Additional operations

To Operation

Stop Press x

Pause Press X

Resume play after

pause

Press Xor H

Go to the next chapter,

track or scene in

continuous play mode

Press >

Go back to the

preceding chapter,

track or scene in

continuous play mode

Press .

Stop play and remove

the disc

Press Z

Replay a previous

scene (DVD only)

Press INSTANT

REPLAY

1 2 3

4 5 6

7 8 9

./>

INSTANT

REPLAY

Playing Discs

Resuming Playback from

the Point Where You

StoppedtheDisc

(Resume Play)

When you stop the disc, the player

remembers the point where you pressed x

and “RESUME”appears on the front panel

display. As long as you do not open the disc

tray, Resume Play works even if the player

enters standby mode by pressing [/1.

While playing a disc, press xto

stop playback.

“RESUME”appears on the front panel

display and you can restart the disc

from the point where you stopped the

disc.

If “RESUME”does not appear,

Resume Play is not available.

Press H.

The player starts playback from the

point where you stopped the disc in

Step 1.

To play from the beginning of the disc, press x

twice, then press H.

Notes

•Depending on where you stopped the disc, the player

may not resume playback from exactly the same

point.

•The point where you stopped playing is cleared

when:

—you turn the power off by pressing POWER on

the player.

—you change the play mode.

—you change the settings on the Setup Display.

Using the DVD’s Menu

Some discs have a “title menu”or a “DVD

menu.”On some DVDs, this may simply be

called a “menu”or “title.”

A DVD is divided into long sections of a

picture or a music feature called “titles.”

When you play a DVD which contains

several titles, you can select the title you want

using the title menu.

Press TITLE.

The title menu appears on the TV screen.

The contents of the menu vary from disc

to disc.

Press C/X/x/cor the number buttons to

select the title you want to play.

Press ENTER.

The player starts playing the selected

title.

zYou can also display the title menu by pressing

TITLE on the player.

Some DVDs allow you to select the disc

contents using a menu. When you play these

DVDs, you can select items such as the

language for the subtitles and the language

for the sound using the DVD menu.

Press DVD MENU.

The DVD menu appears on the TV

screen. The contents of the menu vary

from disc to disc.

Press C/X/x/cor the number buttons to

select the item you want to change.

To change other items, repeat Step 2.

Press ENTER.

zYou can also display the DVD menu by pressing

DVD MENU on the player.

Using the title menu

1 2 3

4 5 6

7 8 9

TITLE

ENTER

C/X/x/c

Number

buttons

Using the DVD menu

DVD MENU

ENTER

C/X/x/c

1 2 3

4 5 6

7 8 9

Number

buttons

Playing Discs

Playing VIDEO CDs with

PBC Functions

(PBC Playback)

With PBC (Playback Control) functions, you

can enjoy simple interactive operations,

search functions, and other such operations.

PBC playback allows you to play VIDEO

CDs interactively by following the menu on

the TV screen.

Start playing a VIDEO CD with PBC

functions.

The menu for your selection appears.

Select the item number you want

by pressing X/x or the number

buttons.

Press ENTER.

Follow the instructions in the menu

for interactive operations.

Refer to the instructions supplied with

the disc, as the operating procedure may

differ according to the VIDEO CD.

To go back to the menu

Press ORETURN.

To play without using PBC, press ./>or the

number buttons while the player is stopped to select a

track, then press Hor ENTER.

“Play without PBC”appears on the TV screen and the

player starts continuous play. You cannot play still

pictures such as a menu.

To return to PBC playback, press xtwice then press

Note

Depending on the VIDEO CD, “Press ENTER”in

Step 3 may appear as “Press SELECT”in the

instructions supplied with the disc. In this case, press

1 2 3

4 5 6

7 8 9

./>

ORETURN

X/x

ENTER

Number

buttons

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-8

Various Play Mode

Functions

(Program Play, Shuffle

Play, Repeat Play, A-B Repeat Play)

You can set the following play modes:

•Program Play (page 34)

•Shuffle Play (page 36)

•Repeat Play (page 36)

•A- B Repeat Play (page 37)

Notes

•The play mode is canceled when:

—you open the disc tray.

—the player enters standby mode by pressing [/1

on the remote.

—you turn the power off by pressing POWER on

the player.

•If you are playing a VIDEO CD with PBC, you must

first cancel PBC playback before you can set a play

mode (except when you want to set A-B Repeat Play

for moving pictures).

You can play the contents of a disc in the

order you want by arranging the order of the

titles, chapters, or tracks on the disc to create

your own program. You can program up to 99

titles, chapters, and tracks.

Press DISPLAY twice (when playing a

CD, press once).

The Control Menu appears.

Press X/xto select

(PROGRAM), then press ENTER.

The options for PROGRAM appear.

Press X/xto select “SET t,” then

press ENTER.

The display for programming appears.

Press c.

The cursor moves to the title or track (in

this case, “01”).

Creatingyour own program(Program

Play)

1 2 3

4 5 6

7 8 9

X/x/c

DISPLAY

PROGRAM

CLEAR

ENTER

Number

buttons

SHUFFLE REPEAT

OFF

SET

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

PLAY

PROGRAM

1. TITLE

ALL CLEAR

2. TITLE – –

3. TITLE – –

4. TITLE – –

5. TITLE – –

6. TITLE – –

7. TITLE – –

– –

“TRACK”is displayed when you play a

VIDEO CD or a CD.

Titles or tracks

recorded on a disc

PROGRAM

1. TITLE – –

ALL CLEAR

2. TITLE – –

3. TITLE – –

4. TITLE – –

5. TITLE – –

6. TITLE – –

7. TITLE – –

ALL

– –

Chapters recorded on a disc

Playing Discs

5Select the title, chapter, or track you

want to program.

xWhen playing a DVD

For example, select chapter “03”of title “02.”

Press X/xor the number buttons to select

“02”under “T,”then press ENTER.

Next, press X/xor the number buttons to

select “03”under “C,”then press

ENTER.

xWhen playing a VIDEO CD or CD

For example, select track “02.”

Press X/xor the number buttons to select

“02”under “T,”then press ENTER.

6To program other titles, chapters, or

tracks, repeat Steps 4 to 5.

The programmed titles, chapters, and

tracks are displayed in the selected order.

7Press Hto start Program Play.

Program Play begins.

When the program ends, you can restart

the same program again by pressing H.

To return to normal play

Press CLEAR, or select “OFF”in Step 3.

To play the same program again, select “ON”

in Step 3 and press H.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

To change the program

1In Step 4, select the program number of

the title, chapter, or track you want to

change using X/xor the number buttons,

and press c.

2Follow Step 5 for new programming.

To cancel the programmed order

To cancel all the titles, chapters, or tracks in

the programmed order, press X, and select

“ALL CLEAR”in Step 4. To cancel the

selected program, select the program using

X/xin Step 4, then press CLEAR, or select

“--”in Step 5, then press ENTER. To cancel

the program directly, select the program

using the number buttons, followed by

ENTER.

You can do Repeat Play or Shuffle Play of the

programmed titles, chapters, or tracks. Press REPEAT

or SHUFFLE on the remote, or set “REPEAT”or

“SHUFFLE”to “ON”in the Control Menu display

during Program Play.

You can select “PROGRAM”directly by pressing

PROGRAM.

Note

The number of titles, chapters, or tracks displayed is

the same as the number of titles, chapters, or tracks

recorded on a disc.

PROGRAM

1. TITLE – –

ALL CLEAR

2. TITLE – –

3. TITLE – –

4. TITLE – –

5. TITLE – –

6. TITLE – –

7. TITLE – –

ALL

– –

PROGRAM

1. TITLE 0 2 – 0 3

ALL CLEAR

2. TITLE – –

3. TITLE – –

4. TITLE – –

5. TITLE – –

6. TITLE – –

7. TITLE – –

Selected title and chapter

PROGRAM

1. TRACK 0 2

ALL CLEAR

2. TRACK

– –

3. TRACK – –

4. TRACK – –

5. TRACK – –

6. TRACK – –

7. TRACK – –

0:15:30

– –

Selected track

Total time of the programmed tracks

continued

You can have the player “shuffle”titles,

chapters, or tracks and play them in a random

order. Subsequent “shuffling”may produce a

different playing order.

Press DISPLAY twice during playback

(when playing a CD, press once).

The Control Menu appears.

Press X/x to select

(SHUFFLE), then press ENTER.

The options for SHUFFLE appear.

Press X/xto select the item.

xWhen playing a DVD (Program

Play is set to OFF)

•TITLE: shuffles titles and plays them

in a random order.

•CHAPTER: shuffles chapters and

plays them in a random order.

xWhen playing a VIDEO CD or CD

(Program Play is set to OFF)

•TRACK: shuffles tracks and plays

them in a random order.

xWhen playing a VIDEO CD, CD,

or DVD (Program Play is set to ON)

•ON: shuffles titles or tracks selected

in Program Play and plays them in a

random order.

Press ENTER.

Shuffle Play starts.

To return to normal play

Press CLEAR or select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

zYou can set Shuffle Play while the player is

stopped. After selecting the “SHUFFLE”option, press

H. Shuffle Play starts.

zYou can select SHUFFLE directly by pressing

SHUFFLE.

Note

Up to 200 chapters in a disc can be played in random

order when “CHAPTER”is selected.

You can play all of the titles or tracks on a

disc, or a single title, chapter, or track

repeatedly.

You can use a combination of Shuffle or

Program Play modes.

Playing in random order (Shuffle

Play)

DISPLAY

X/x

ENTER

SHUFFLE

CLEAR

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

OFF

CHAPTER

TITLE

DVD

PLAY

OFF

Playing repeatedly (Repeat Play)

456

ENTER

X/x

DISPLAY

REPEAT

CLEAR

Playing Discs

1Press DISPLAY twice during playback

(when playing a CD, press once).

The Control Menu appears.

2Select

(REPEAT) using X/x,

then press ENTER.

The options for REPEAT appear.

3Press X/xto select the item.

xWhen playing a DVD (Program

Play and Shuffle Play are set to

OFF)

•DISC: repeats all of the titles.

•TITLE: repeats the current title on a

disc.

•CHAPTER: repeats the current

chapter.

xWhen playing a VIDEO CD or CD

(Program Play and Shuffle Play are

set to OFF)

•DISC: repeats all of the tracks on a

disc.

•TRACK: repeats the current track.

xWhen Program Play or Shuffle

Play is on

•ON: repeats Program Play or Shuffle

Play.

4Press ENTER.

Repeat Play starts.

To return to normal play

Press CLEAR, or select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

You can set Repeat Play while the player is

stopped. After selecting the “REPEAT”option, press

H. Repeat Play starts.

You can select “REPEAT”directly by pressing

REPEAT.

You can play a specific portion of a title,

chapter, or track repeatedly. (This function is

useful when you want to memorize lyrics, etc.)

1Press DISPLAY twice during playback

(when playing CD, press once).

The Control Menu appears.

2Press X/xto select (A-B

REPEAT), then press ENTER.

The options for A-B REPEAT appear.

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

CHAPTER

DISC

OFF

TITLE

OFF

DVD

PLAY

Repeating a specific portion (A-B

Repeat Play)

4 5 6

7 8 9

ENTER

X/x

DISPLAY

CLEAR

SET

OFF

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

PLAY

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-9

Press X/xto select “SET t,”then

press ENTER.

The A-B REPEAT setting display

appears.

During playback, when you find the

starting point (point A) of the portion to

be played repeatedly, press ENTER.

The starting point (point A) is set.

When you reach the ending point (point

B), press ENTER again.

The set points are displayed and the

player starts repeating this specific

portion.

“A-B”appears in the front panel display

during A-B Repeat Play.

To return to normal play

Press CLEAR, or select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

Notes

•You can set A-B Repeat Play for only one specific

section.

•When you set A-B Repeat Play, the settings for

Shuffle Play, Repeat Play, and Program Play are

canceled.

Set point A with

A-B REPEAT

ENTER

A: 18 – 1 : 32 : 55

CHAPTER

TIME

Set point B with .

ENTER

A-B REPEAT

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 34 : 30

DVD

A: 18 – 1 : 32 : 55

B: 1

– 1 :

4 :

CHAPTER

TIME

PLAY

Searching for a Scene

Searching for a Particular

Point on a Disc

(Search, Scan,

Slow-Motion Play, Freeze Frame)

You can quickly locate a particular point on a

disc by monitoring the picture or playing

back slowly.

Note

Depending on the DVD/VIDEO CD, you may not be

able to do some of the operations described.

During playback, keep pressing Cto

locate a point in playback direction at the

FF1M* speed or keep pressing cto

locate a point in opposite direction at the

FR1m* speed. When you find the point

you want, release the button to return to

normal playback speed.

∗The FF1M/FR1mplayback speed is the same as

the scan speed and click shuttle speed described

below.

Press or ywhile playing a disc.

When you find the point you want, press H

to return to normal speed.

Each time you press or yduring

scan the playback speed changes. Three

speeds are available. With each press the

indication changes as follows:

Playback direction

Opposite direction

The ×2

/×2

playback speed is about twice

the normal speed. The FF2

/FR2

playback speed is faster than FF1

/FR1

You can use this function only for DVDs or

VIDEO CDs. Press or ywhen the

player is in the pause mode. To return to the

normal speed, press H.

Each time you press the or ybutton

during Slow-motion play, the playback speed

changes. Two speeds are available. With

each press the indication changes as follows:

Playback direction

SLOW 2yySLOW 1y

Opposite direction (DVD only)

SLOW 2 ySLOW 1

The SLOW2y/SLOW2 playback speed

is slower than SLOW1y/SLOW1 .

Locating a point quickly (Search)

1 2 3

4 5 6

7 8 9

c/C

Locating a point quickly by playing a

disc in fast forward or fast reverse

(Scan)

Watching frame by frame (Slow-

motion play)

×2

(DVD/CD only) t FF1

tFF2

×2

(DVD only) t FR1

tFR2

continued

You can use this function only for DVDs or

VIDEO CDs. When the player is in the pause

mode, press Cto go to the next frame.

Press cto go to the preceding frame

(DVD only). If you hold the button down,

you can view the frames in succession. To

return to normal playback, press H

Turn the click shuttle on the player. The

playback speed changes depending on the

turning direction and degree of rotation as

follows:

During playback

FF2MFast forward (faster than

“FF1M”)

FF1MFast forward

×2B(DVD/CD only)

PLAYN(normal speed)

×2b(DVD/CD only)

FR1mFast rewind

FR2m Fast rewind (faster than

“FF1m”)

If you turn the click shuttle quickly, the

playback speed goes to FF2Mor

FR2mat once.

During pause mode (DVD only)

SLOW1ySlow (playback direction)

SLOW2ySlow (playback direction –

slower than “SLOW1y”)

PAUSEXPause

SLOW2 Slow (opposite direction –

slower than “SLOW1 ”)

SLOW1 Slow (opposite direction)

During pause mode (VIDEO CD only)

SLOW1ySlow (playback direction)

SLOW2ySlow (playback direction –

slower than “SLOW1y”)

PAUSEXPause

To return to continuous play

Press H.

Playing one frame at a time

Using the click shuttle on the player

(Shuttle mode)

Click shuttle

JOG

Searching for a Scene

1Press JOG.

The player enters pause mode.

2Turn the click shuttle.

Depending on the turning speed,

playback goes to frame-by-frame

playback in the direction that the click

shuttle is turned (turn clockwise to go

forward, counter clockwise to rewind). If

you turn the click shuttle at a constant

speed for a while, the playback speed

goes to slow or normal.

To return to Continuous Play

Press H.

To turn off the Jog mode

Press JOG again so that the indicator turns

off.

Searching for a Title/

Chapter/Track/Index/

Scene

(Search mode)

You can search a DVD disc by title or

chapter, and you can search a VIDEO CD or

CD by track, index, or scene. As titles and

tracks are assigned unique numbers on the

disc, you can select the desired one by

entering its number. Or, you can search for a

scene using the time code (Time search).

Press DISPLAY.

The Control Menu appears.

Press X/xto select the search

method.

xWhen playing a DVD

(TITLE),

(CHAPTER), or (TIME/

TEXT)

Select “TIME/TEXT”for “Time search”

(see below).

xWhen playing a VIDEO CD

(TRACK) or

(INDEX)

To manually play the disc frame by

frame using the click shuttle

(Jog mode)

1 2 3

4 5 6

7 8 9

X/x

DISPLAY

ENTER

CLEAR

Number

buttons

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-10

xWhen playing a VIDEO CD with

PBC Playback

(SCENE)

xWhen playing a CD

(TRACK) or

(INDEX)

Example: when you select

(CHAPTER)

“

(

)”is selected (

refers to a

number).

The number in parentheses indicates the

total number of titles, chapters, tracks,

indexes, or scenes.

3Press ENTER.

“

(

)”changes to “-- (

).”

4Select the number of the title,

track, scene, time code, etc. you

want by pressing X/xor the

number buttons to select the digit.

If you make a mistake

Cancel the number by pressing CLEAR,

then select another number.

5Press ENTER.

The player starts playback from the

selected number.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

To search for a scene using the time

code (Time search) (DVD only)

In Step 2, select (TIME/

TEXT).

“T

”(playing time of the current

title) is selected.

Press ENTER.

“T

”changes to

“T --:--:--.”

Input the time code using the number

buttons, then press ENTER.

For example, to find the scene at 2 hours,

10 minutes, and 20 seconds after the

beginning, just enter “2:10:20.”

zYou can display the first scene of titles, chapters or

tracks recorded on the disc on a screen divided into 9

scenes. You can start playback directly by selecting

one of the scenes. For details, see page 43.

Note

The title, chapter, or track number displayed is the

same number recorded on the disc.

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

PLAY

Selected row

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

– –

( 3 4 )

PLAY

Searching for a Scene

Searching by Scene

(VIEWER)

You can divide the screen into 9 sub-screens

and find the desired scene quickly.

Press DISPLAY twice during

playback.

The Control Menu appears.

Press X/xto select

(VIEWER), then press ENTER.

The options for VIEWER appear.

Press X/xto select the item.

Refer to the explanations given for each

item in the following sections.

•STROBE PLAYBACK

•TITLE VIEWER (for DVD only)

•CHAPTER VIEWER (for DVD only)

•TRACK VIEWER (for VIDEO CD

only)

•ANGLE VIEWER (for DVD only)

Press ENTER.

To return to the normal play

Press O RETURN.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

Notes

•Depending on the disc, you may not be able to select

all functions.

•The sound is muted when using this function.

You can display 9 consecutive moving

pictures on the screen. When you press X,

the moving pictures pause.

Select “STROBE PLAYBACK”in Step 3,

then press ENTER in Step 4.

You can divide the screen into 9 subscreens

and display the first scene of titles, chapters,

or tracks. You can also play back from the

selected title, chapter, or track.

Select the item you want in Step 3, then press

ENTER in Step 4.

xWhen playing a DVD

Select “

TITLE VIEWER”or

“

CHAPTER

VIEWER.”

xWhen playing a VIDEO CD

Select “

TRACK VIEWER.”

The initial scenes of titles, chapters, or tracks

appear.

ENTER

C/X/x/c

O RETURN

DISPLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

STROBE PLAYBACK

ANGLE VIEWER

CHAPTER VIEWER

TITLE VIEWER

STROBE PLAYBACK

PLAY

Dividing a track into 9 sections

(STROBE PLAYBACK)

Scanning the title, chapter, or track

continued

To start playback from the selected

scene

Select the scene using C/X/x/c, then press

ENTER. The playback starts from the

selected scene.

zIf there are more than 9 titles, chapters, or tracks,

Vis displayed at the bottom right.

To display the additional titles, chapters, or tracks,

select the bottom right scene (the position 9) and press

x. To return to the previous scene, select the top left

scene (the position 1), then press X.

If various angles (multi-angles) for a scene

are recorded on the DVD, you can display all

of the angles recorded on the disc on the same

screen, and start playback in continuous

mode at the chosen angle. The angles are

displayed on a screen divided in 9 sections.

Select “ANGLE VIEWER”in Step 3, then

press ENTER in Step 4.

To return to the normal play

Press ORETURN.

Displaying different angles

simultaneously

Viewing Information About the Disc

Viewing the Playing Time

and Remaining Time on

the Front Panel

Display

You can check information about the disc,

such as the remaining time, total number of

titles of a DVD, or tracks of a CD or VIDEO

CD, using the front panel display (page 9).

Press TIME/TEXT.

Each time you press TIME/TEXT while

playing the disc, the display changes as

shown in the following charts.

When playing a DVD

When playing a VIDEO CD (without

PBC functions) or CD

When playing VIDEO CDs with PBC functions,

the scene number and the playing time are displayed.

TIME/TEXT

CHAP HOUR MIN SEC

TITLE CHAP HOUR MIN SEC

CHAP HOUR MIN SEC

Title playing time and the current title and

chapter number

Remaining time of the current title

Playing time and number of

the current

chapter

Remaining time of the current chapter

Text

TRACK INDEX MIN SEC

MIN SEC

TRACK INDEX MIN SEC

Track playing time and the current track and

index number

Remaining time of the current track

Remaining time of the disc

ext

Playing time of the disc

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-11

The playing time and remaining time of the current

chapter, title, track, scene, or disc will also appear on

your TV screen. See the following section “Checking

the Playing Time and Remaining Time”for

instructions on how to read this information.

Note

Depending on the type of disc being played and the

playing mode, the above mentioned disc information

may not be displayed.

Checking the Playing

Time and Remaining

Time

You can check the playing time and

remaining time of the current title, chapter, or

track, and the total playing time or remaining

time of the disc. Also, you can check the

DVD/CD text recorded on the disc.

1Press DISPLAY during playback.

The Control Menu appears.

2Press TIME/TEXT repeatedly to

change the time information.

The display and the kinds of time that

you can change depend on the disc you

are playing.

TIME/TEXT

DISPLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

PLAY

Playing time of title

or track

Disc type

Viewing Information About the Disc

xWhen playing a DVD

•T

Playing time of the current title

•T–

Remaining time of the current title

•C

Playing time of the current chapter

•C–

Remaining time of the current chapter

xWhen playing a VIDEO CD (with

PBC functions)

•

Playing time of the current scene

xWhen playing a VIDEO CD

(without PBC functions) or CD

•T

Playing time of the current track

•T–

Remaining time of the current track

•D

Playing time of the current disc

•D–

Remaining time of the current disc

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

Checking the DVD/CD text

Press TIME/TEXT repeatedly in Step 3 to

display the text recorded on the DVD/CD.

The DVD/CD text appears only when text is

recorded in the disc. You cannot change the

text. If the disc does not contain text, “NO

TEXT”appears.

zIf the DVD/CD text does not fit on a single line,

you can see the entire text by watching it scroll across

the front display.

zYou can select the time and text by pressing

TIME/TEXT.

Notes

•Only letters of the alphabet can be displayed.

•This player can only display the first level of DVD/

CD text, such as the disc name or title.

TIME/TEXT

BRAHMS SYMPHONY NO – 4

DVD/CD text

Checking the Play

Information(ADVANCED)

You can check information such as the bit

rate or the disc layer that is being played.

While playing a disc, an approximate bit rate

of the playback picture is always displayed as

Mbps (Mega bit per second) and the audio as

kbps (kilo bit per second).

1Press DISPLAY during playback.

The Control Menu is displayed.

2Press X/xto select

(ADVANCED), then press ENTER.

The options for ADVANCED appear.

3Press X/xto select items.

For each item, please refer to “Displays

of each item.”

•BIT RATE: displays the bit rate.

•LAYER: displays the layer and the

pick-up point.

4Press ENTER.

To close the ADVANCED window

Select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

By pressing DISPLAY repeatedly, you can

display either “BIT RATE”or “LAYER,”

whichever was selected in “ADVANCED.”

BIT RATE

Bit rate refers to the amount of video/audio

data per second in a disc. The higher the bit

rate, the larger the amount of data. When the

bit rate level is high, there is a large amount

of data. However, this does not always mean

that you can get higher quality pictures or

sounds.

LAYER

Indicates the approximate point where the

disc is playing.

If it is a dual-layer DVD, the player indicates

which layer is being read (“Layer 0”or

“Layer 1”).

For details on the layers, see page 79 (DVD).

ENTER

X/x

DISPLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

BIT RATE

DVD

BIT RATE

0510

kbps

Mbps

384

PLAY

OFF

LAYER

BIT RATE

Displays of each item

BIT RATE

0510

kbps

Mbps

384

Audio

Video

Appears when the DVD

has dual layers

Sound Adjustments

Changing the Sound

If the DVD is recorded with multilingual

tracks, you can select the language you want

while playing the DVD.

If the DVD is recorded in multiple audio

formats (PCM, Dolby Digital, or DTS), you

can select the audio format you want while

playing the DVD.

With stereo CDs or VIDEO CDs, you can

select the sound from the right or left channel

and listen to the sound of the selected channel

through both the right and left speakers. (In this

case, the sound loses its stereo effect.) For

example, when playing a disc containing a song

with the vocals on the right channel and the

instruments on the left channel, you can select

the left channel and hear the instruments from

both speakers.

Press DISPLAY during playback.

The Control Menu is displayed.

Press X/xto select

(AUDIO), then ENTER.

The options for AUDIO appear.

Press X/xto select the desired

audio signal.

xWhen playing a DVD

Depending on the DVD, the choice of

language varies.

When 4 digits are displayed, they

represent the language code. Refer to

the language code list on page 82 to see

which language the code represents.

When the same language is displayed

two or more times, the DVD is recorded

in multiple audio formats.

xWhen playing a VIDEO CD or

The default setting is underlined.

•STEREO: The standard stereo

sound

•1/L: The sound of the left channel

(monaural)

•2/R: The sound of the right channel

(monaural)

Press ENTER.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

You can select “AUDIO”directly by pressing

AUDIO. Each time you press the button, the item

changes.

Notes

•For discs not in multiple audio format, you cannot

change the sound.

•While playing the DVD, the sound may change

automatically.

1 2 3

4 5 6

7 8 9

ENTER

X/x

AUDIO

DISPLAY

DVD

2: ENGLISH

3: FRENCH

1: ENGLISH

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

LRC

DOLBY DIGITAL 3/2.1

PROGRAM FORMAT

LFE

LS RS

1: ENGLISH

PLAY

continued

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-12

When you select “AUDIO,”the channels

being played are displayed on the screen.

For example, in Dolby Digital format,

multiple signals ranging from monaural to

5.1 channel signals can be recorded on a

DVD. Depending on the DVD, the number of

the recorded channels may differ.

*“PCM,”“DTS,”or “DOLBY DIGITAL”is

displayed.

In the case of “DOLBY DIGITAL,”the

channels in the playing track are displayed

by numbers as follows:

For Dolby Digital 5.1 ch:

**The letters in the program format display

mean the following sound component:

L: Front (left)

R : Front (right)

C : Center

LS : Rear (left)

RS : Rear (right)

S : Rear (monaural): The rear

component of the Dolby Surround

processed signal or the Dolby

Digital signal.

LFE :Low Frequency Effect signal

The display examples are as follows:

•PCM (stereo)

•Dolby Surround

•Dolby Digital 5.1ch

“LFE”is always enclosed in a solid line

regardless of the LFE signal component

being output.

•DTS

“LFE”is always enclosed in a solid line

regardless of the LFE signal component

being output.

Notes

•When the signal contains rear signal components

such as “LS,”“RS”or “S,”the surround effect is

enhanced (page 51).

•If “DTS”is set to “OFF”in “AUDIO SETUP”(page

75), the DTS track selection option will not appear

on the screen even if the disc contains DTS tracks.

Displaying the audio information of

the disc

DVD

1: ENGLISH

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

LRC

DOLBY DIGITAL 3/2.1

PROGRAM FORMAT

LFE

LS RS

PLAY

Current audio format*

Currently playing program format**

DOLBY DIGITAL

3 / 2

LFE (Low Frequency

Effect) component 1

Rear

component 2

Front component 2 +

Center component 1

PCM 48kHz 24bit

PROGRAM FORMAT

DOLBY SURROUND

DOLBY DIGITAL 2/0

L RC

PROGRAM FORMAT

LRC

DOLBY DIGITAL 3/2.1

PROGRAM FORMAT

LFE

LS RS

LRC

DTS 3/2.1

PROGRAM FORMAT

LFE

LS RS

Sound Adjustments

TVVirtualSurroundSound

Settings

(TVS)

When you connect a stereo TV or 2 front

speakers, TV Virtual Surround lets you enjoy

surround sound effects by using sound

imaging to create virtual rear speakers from

the sound of the front speakers (L: left, R:

right) without using actual rear speakers.

This function is designed to work with the

LINE OUT L/R (AUDIO) 1/2 jacks.

Note that if you select one of the TVS settings

while playing a DVD, the player does not

output Dolby Digital signals from the

DIGITAL OUT (COAXIAL and OPTICAL)

jacks (when you set “DOLBY DIGITAL”in

“AUDIO SETUP”to “D-PCM”) (page 75).

Press DISPLAY during playback.

The Control Menu appears.

Press X/xto select

(TVS), then press ENTER.

The options for “TVS”appear.

Press X/xto select one of the TVS

(TV Virtual Surround) sounds.

Refer to the following explanations

given for each item.

•TVS DYNAMIC

•TVS WIDE

•TVS NIGHT

•TVS STANDARD

Press ENTER.

To reset the TVS setting

Select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

TVS (TV Virtual Surround) DYNAMIC

Uses sound imaging to create virtual rear

speakers from the sound of the front speakers

(L/R) without using actual rear speakers

(shown below). The sound imaging effect is

distinct and clearly reproduces each aural

element of the audio track.

This mode is effective when the distance

between the front L and R speakers is short,

such as with built-in speakers on a stereo TV.

ENTER

X/x

DISPLAY

SURROUND

TVS DYNAMIC

OFF

TVS WIDE

OFF

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

VIRTUAL 3D SURROUND

PLAY

continued

TVS (TV Virtual Surround) WIDE

Uses sound imaging to create virtual rear

speakers from the sound of the front speakers

(L/R) without using actual rear speakers. The

virtual speakers are reproduced as shown in

the illustration below. This gives the sound

an expanded effect that fills the area

surrounding the listener.

This mode is effective when the distance

between the front L and R speakers is short,

such as with built-in speakers on a stereo TV.

TVS (TV Virtual Surround) NIGHT

Large sounds, such as explosions, are

suppressed, but the quieter sounds are

unaffected. This feature is useful when you

don’t want to disturb other people but still

want to hear the dialog and enjoy the

surround sound effects of TVS WIDE.

TVS (TV Virtual Surround) STANDARD

Uses sound imaging to create virtual rear

speakers from the sound of the front speakers

(L/R) without using actual rear speakers. The

virtual speakers are reproduced as shown in

the illustration below. Use this setting when

you want to use TVS with 2 separate speakers

and retain the sound quality.

zYou can select “TVS”directly by pressing

SURROUND on the remote or player.

Each time you press the button, the item changes.

If you select any TVS setting other than “OFF,”the

indicator on the player lights up.

Notes

•When you select an effect, the sound cuts off for a

moment.

•When the playing signal does not contain a signal for

the rear speakers (page 50), the surround effects may

be difficult to hear.

•When you select one of the TVS modes, turn off the

surround setting of the connected TV or amplifier

(receiver).

•Make sure that your listening position is between

and at an equal distance from your speakers, and that

the speakers are located in similar surroundings.

Otherwise, the TVS effect may be hard to discern.

•TVS NIGHT only works with Dolby Digital discs.

However, not all discs will respond to the TVS

NIGHT function in the same way.

•If you use the DIGITAL OUT (OPTICAL or

COAXIAL) jacks, the sound output from your

speakers will not have the TVS effect.

L : Front speaker (left)

R : Front speaker (right)

: Virtual speaker

Enjoying Movies

Changing the Angles

If various angles (multi-angles) for a scene

are recorded on the DVD, “ANGLE”appears

in the front panel display. This means that

you can change the viewing angle.

For example, while playing a scene of a train

in motion, you can display the view from

either the front of the train, the left window of

the train, or from the right window without

having the train’s movement interrupted.

Press DISPLAY during playback.

The Control Menu appears.

Press X/xto select

(ANGLE).

The number of the angle appears.

The number in parentheses indicates the

total number of angles.

Press c or ENTER.

The number of the angle changes to “-.”

Select the angle number using the

number buttons or X/x, then press

ENTER.

The angle changes to the selected angle.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

You can select the angle directly by pressing

ANGLE. Each time you press the button, the angle

changes.

You can display all the angles recorded on the disc

on the same screen, and start playback directly in

continuous mode from the chosen angle. The angles

are displayed on a screen divided in 9 sections. For

details, see page 43.

Note

Depending on the DVD, you may not be able to

change the angles even if multi-angles are recorded on

the DVD.

1 2 3

4 5 6

7 8 9

ENTER

X/x/c

Number

Buttons ANGLE

DISPLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

1 ( 9 )

PLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

PLAY

–

( 9 )

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

1-13

Displaying the Subtitles

If subtitles are recorded on the discs, you can

turn the subtitles on and off whenever you want

while playing. If multilingual subtitles are

recordedon the disc, you can change the subtitle

language while playing, and turn it on or off

whenever you want. For example, you can

select the language you want to practice and

turn the subtitles on for better understanding.

1Press DISPLAY during playback.

The Control Menu appears.

2Press X/xto select

(SUBTITLE), then press ENTER.

The options for SUBTITLE appear.

3Press X/xto select the language.

Depending on the DVD, the choice of

language varies.

When 4 digits are displayed, they

indicate the language code. Refer to the

language code list on page 82 to see

which language the code represents.

4Press ENTER.

To cancel the SUBTITLE setting

Select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

zYou can select SUBTITLE directly by pressing

SUBTITLE. Each time you press the button, the item

changes.

Note

Depending on the DVD, you may not be able to

change the subtitles even if multilingual subtitles are

recorded on the DVD.

1 2 3

4 5 6

7 8 9

ENTER

X/x

SUBTITLE

DISPLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

OFF

1: ENGLISH

2: FRENCH

3: SPANISH

OFF

DVD

PLAY

Enjoying Movies

Adjusting the Picture

Quality

(BNR)

The Block Noise Reduction (BNR) function

adjusts the picture quality by reducing the

“block noise”or mosaic like patterns that

appear on your TV screen.

Press DISPLAY twice during

playback.

The Control Menu appears.

Press X/xto select

(BNR), then press ENTER.

The options for BNR appear.

Press X/xto select a level.

As the value increases, the mosaic like

patterns on your TV screen will

decrease.

•1: reduces the “block noise.”

•2: reduces the “block noise”more

than 1.

•3: reduces the “block noise”more

than 2.

Press ENTER.

The disc plays with the setting you

selected.

To cancel the BNR setting

Select “OFF”in Step 3.

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

You can set BNR while the player is stopped.

You can select BNR directly by pressing BNR on

the remote or player. Each time you press the button,

the item changes. If you select any setting other than

“OFF,”the indicator on the player lights up.

Notes

•If the outlines of the images on your screen should

become blurred, set “BNR”to “OFF.”

•Depending on the disc or the scene being played, the

BNR effect may be hard to discern.

1 2 3

4 5 6

7 8 9

X/x

BNR

ENTER

DISPLAY

OFF

DVD

OFF

PLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

Adjusting the Playback

Picture(VIDEO EQUALIZER)

You can adjust the video signal of the DVD

or VIDEO CD from the player, not from the

TV, to obtain the picture quality you want.

Choose the video mode that suits the program

you are watching.

When you select “MEMORY t,”you can

make further adjustments to each element of

the picture (color, brightness, etc.).

1Press DISPLAY twice during

playback.

The Control Menu appears.

2Press X/xto select

(VIDEO EQUALIZER), then press

ENTER.

The options for VIDEO EQUALIZER

appear.

3Press X/xto select the setting you

want.

•STANDARD: displays a standard

picture.

•DYNAMIC 1: produces a bold

dynamic picture by increasing the

picture contrast and the color

intensity.

•DYNAMIC 2: produces a more

dynamic picture than DYNAMIC 1

by further increasing the picture

contrast and the color intensity.

•CINEMA 1: enhances details in dark

areas by increasing the black level.

•CINEMA 2: White colors become

brighter and black colors become

richer, and the color contrast is

increased.

•MEMORY t: adjusts the picture in

greater detail.

4press ENTER

To turn off the Control Menu

Press DISPLAY repeatedly until the Control

Menu is turned off.

When you watch a movie “CINEMA 1”or

“CINEMA 2”is recommended.

You can set VIDEO EQUALIZER while the

player is stopped.

You can adjust each element of the picture

individually.

•PICTURE: changes the contrast

•BRIGHTNESS: changes the overall

brightness

•COLOR: makes the colors deeper or lighter

•HUE: changes the color balance

X/x

ENTER

DISPLAY

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

DYNAMIC 1

DYNAMIC 2

CINEMA 1

STANDARD

Sl C l

VIDEO EQUALIZER

PLAY

Adjusting the picture items in

“MEMORY”

X/x

ENTER

DISPLAY O RETURN

Enjoying Movies

1Press DISPLAY twice during playback.

The Control Menu appears.

2Press X/xto select (VIDEO

EQUALIZER), then press ENTER.

3Press X/xto select “MEMORY t,”and

press ENTER.

The video equalizer display appears.

4Select the picture item you want to

adjust using X/x, then press ENTER.

The adjustment bar of the selected item

appears.

5Adjust the selected picture item using

C/c, then press ENTER.

The setting is stored in memory.

To cancel adjusting the picture

Press O RETURN before pressing

ENTER to return to Step 2.

6To adjust other items, repeat Steps 4

and 5.

To turn off the video equalizer

memory display

Press ORETURN.

To reset all of the picture items, select “RESET”in

Step 4.

Note

Only one set of “MEMORY t”adjustments can be

stored. When you adjust the items again, the new

setting erases the previous setting.

1 8 ( 3 4 )

1 2 ( 2 7 )

1 : 3 2 : 5 5

DVD

DYNAMIC 1

DYNAMIC 2

CINEMA 1

STANDARD

PLAY

()

0 1 : 3 2 : 5 5

VIDEO EQUALIZER

PICTURE

BRIGHTNESS

COLOR

HUE

RESET

TEL 13942296513 QQ 376315150 892498299

http://www.xiaoyu163.com

Other manuals for DVP-NS700P - Cd/dvd Player

Table of contents

Other Sony DVD Player manuals

Sony

Sony DVP-SR500H User manual

Sony

Sony RDR-GX300 Setup guide

Sony

Sony DVP-S300 User manual

Sony

Sony DVP-NS300 User manual

Sony

Sony DVP-NS315 User manual

Sony

Sony DVP-CX875P User manual

Sony

Sony DVP-NC80V Operating Instructions (DVPNC80V) User manual

Sony

Sony DVP-S735D User manual

Sony

Sony DVP-S725D User manual

Sony

Sony 4-169-957-12(1) User manual

Sony

Sony BDP-S6500 User manual

Sony

Sony DVP-NS300 Installation guide

Sony

Sony SLV-D100 Notes on operations & the setup... User manual

Sony

Sony DVPC-X850D User manual

Sony

Sony DVP-NS300 User manual

Sony

Sony SRW5100/2 User manual

Sony

Sony DVP-NC600 - Cd/dvd Player User manual

Sony

Sony DVP-NW50 - In-wall Dvd Player User manual

Sony

Sony DVPNS61 User manual

Sony

Sony DVP-NC625 User manual

Sony

Sony DVP-CX860 User manual

Sony

Sony DVP-F21 - Cd/dvd Player User manual

Sony

Sony DVP-C670D - Cd/dvd Player User manual

Sony

Sony SLV-D900E User manual

Popular DVD Player manuals by other brands

Manta

Manta DVD-002 user manual

Asus

Asus Asteio D22 quick start guide

Kenwood

Kenwood DV-502 Service manual

Philips

Philips DVDR3400 user manual

Philips

Philips HTP5980K/93 user manual

Panasonic

Panasonic DVD-S55 operating instructions

Panasonic

Panasonic DVD-S500EB-K operating instructions

LG DV580 owner's manual

Samsung

Samsung DVD-C505 user guide

Sylvania

Sylvania HT6051F Service manual

Trevi

Trevi DVMI 3541 SD user manual

Philips

Philips DVP5992/F7E user manual

Pioneer

Pioneer DV-290 operating instructions

Philips

Philips DVP5100K Service manual

Pioneer

Pioneer DV-266-S operating instructions

Philips

Philips DVP3600K user manual

Panasonic

Panasonic DVD-XV10 operating instructions

Philips

Philips DVD707/751 Service manual

Sony DVP-NS700P - Cd/dvd Player User manual

Popular DVD Player manuals by other brands