Sony SA-VE312 User manual

SA-VE312/VE315/WMS315/
SS-CN315/V315
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
SERVICE MANUAL
MICRO SATELLITE SYSTEM
• The SA-VE312 system consists of one unit
of SA-WMS315 and two units of SS-V315.
• The SA-VE315 system consists of one unit
of SA-WMS315, one unit SS-CN315 and
four units of SS-V315.
SPECIFICATIONS
Photo: SA-WMS315 Photo: SS-CN315
Photo: SS-V315
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION :
with 8 Ωloads both channels driven, from 20 - 150 Hz; rated
75 W per channel minimum RMS power, with no more than
0.8% total harmonic distortion from 250 mW to rated output.
SS-V315 (front and rear speakers)
Speaker system Full range, magnetically shielded
Speaker units 5 ×10 cm (2 ×4 in.), cone type
Enclosure type Bass reflex
Rated impedance 8 Ω
Power handling capacity
Maximum input power: 100 W
Sensitivity level 87 dB (1W, 1m)
Frequency range 90 Hz - 20,000 Hz
Dimensions (w/h/d) Approx. 68 ×150 ×125 mm
(23/4×6 ×5 in.), including front
grille
Mass
European model: Approx. 640 g (1 lb 7 oz) each
Other model: Approx. 740 g (1 lb 10 oz) each
SS-CN315 (center speaker)
Speaker system Full range ×2, magnetically
shielded
Speaker units 5 ×10 cm (2 ×4 in.), cone type
Enclosure type Bass reflex
Rated impedance 8 Ω
Power handling capacity
Maximum input power: 120 W
Sensitivity level 89 dB (1W, 1m)
Frequency range 90 Hz - 20,000 Hz
Dimensions (w/h/d) Approx. 301 ×68 ×125 mm
(117/8×23/4 ×5 in.), including front
grille
Mass
European model: Approx. 1.4 kg (3 lb 1 oz) each
Other model: Approx. 1.5 kg (3 lb 5 oz) each
SA-WMS315 (subwoofer)
System
Speaker system Active subwoofer, magnetically
shielded
Speaker unit Woofer : 16 cm (63/8in.),
cone type
Enclosure type Advanded SAW type
Continuous RMS power output
(8 Ω, 20 - 150 Hz, 0.8 % THD)
European model: 50 W
Other model: 75 W
Reproduction frequency range
28 Hz - 200 Hz
High frequency cut-off frequency
200 Hz
Inputs
LINE IN (input pin jack)
SPEAKER IN (input terminals)
Outputs
LINE OUT (output pin jack)
SPEAKER OUT (output terminals)
General
Power requirements
European model: 220 - 230 VAC, 50/60 Hz
Other model: 120 V AC, 60 Hz
Power consumptions
European model: 50 W
Other model: 70 W
Dimensions (w/h/d) Approx. 205 ×385 ×385 mm
(81/8×151/4×151/4in.), including
front grille
Mass Approx. 10.5 kg
(23 lb 2 oz)
Supplied accessories
SA-VE315
Foot pads (20)
Audio connecting cords (1)
Speaker connecting cords, 10 m (32 ft 93/4in.) (2)
Speaker connecting cords, 2.5 m (8 ft 21/2in.) (5)
SA-VE312
Foot pads (8)
Audio connecting cords (1)
Speaker connecting cords, 2.5 m (8 ft 21/2in.) (4)
Design and specifications are subject to change
without notice
Ver 1.0 2000.2

2
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINEWITH
MARK 0ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Checkthe antennaterminals, metaltrim, “metallized”knobs, screws,
and all other exposed metal parts forAC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operatedAC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
SAFETY CHECK-OUT
To Exposed Metal
Parts on Set
0.15 µF1.5 kΩAC
Voltmeter
(0.75V)
Earth Ground
Fig.A. Using an AC voltmeter to check AC leakage.

33
SECTION 1
DIAGRAMS
1-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on PrintedWiring Board:
•X: parts extracted from the component side.
•b: Pattern from the side which enables seeing.
•Indication of transistor.
B
These are omitted.
CE
Q
Note on Schematic Diagram:
•All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
•All resistors are in Ωand 1/4W or less unless otherwise
specified.
•2: nonflammable resistor.
•C: panel designation.
•U: B+ Line.
•V: B–Line.
•Voltages are dc with respect to ground under no-signal
conditions.
no mark : AUDIO
•VoltagesaretakenwithaVOM(inputimpedance10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
•Abbreviation
CND : Canadian model
•Circuit Boards Location
SA-WMS315
•IC Block Diagrams
IC302 uPC1237H
IC301 STK350-230
1 2 3 4 5 6 7 8
OVER LOAD DET
F/F
OFFSET DET
LATCH/
AUTORESET
VCC ON
MUTE
AC OFF
DET
VCC
Note:
The components identi-
fied by mark 0or dotted
linewith mark 0arecriti-
cal for safety.
Replace only with part
number specified.
Note:
Lescomposants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
piéce portant le numéro
spécifié.
POWER board
POWER SWITCH board
LED board
CONTROL board
MAIN boar
d
1
2
3
4
5
6
7
8
9
TR3 R1
R2
TR4
TR6
TR7
R4
R9
TR5
TR1
TR2
R6
D4 D3
R7
R8
TR8
D1 D2 R5
R3
INPUT
NF
-VEOUT
+VEOUT
VSS
GND
VCC
SUB

SA-VE312/VE315/WMS315/SS-CN315/V315
44
1-2. SCHEMATIC DIAGRAM (SA-WMS315) •See page 3 for IC block diagrams.
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièceportant lenumérospécifié.

SA-VE312/VE315/WMS315/SS-CN315/V315
55
1-3. PRINTEDWIRING BOARD (SA-WMS315) •See page 3 for Circuit Boards Location.
Ref. No. Location
D101 F-11
D102 F-11
D103 F-11
D104 F-11
D301 D-8
D302 D-8
D303 E-5
D304 E-7
D501 G-5
D502 F-7
D503 G-7
D801 B-11
IC101 F-11
IC102 F-9
IC103 D-11
IC201 B-8
IC301 C-9
IC302 D-9
Q101 G-9
Q102 F-8
Q103 D-10
Q303 E-9
Q401 A-3
Q402 A-3
Q403 A-5
Q404 A-2
•Semiconductor
Location
11
(11)
11
(11)
11
(11)
11
(11)
11
(11)
POWER SWITCH BOARD
POWER BOARD
CONTROL BOARD
LED BOARD
MAIN BOARD
POWER
SPEAKER
LEVEL
MODE
LINE
T501
POWER
TRANSFORMER
RL
OUT IN
ON : MUSYC
OFF: MOVIE
(POWER)
SP1
(SPEAKER)
AC
IN
12
A
B
C
D
E
F
G
H
3456789101112

66
NOTE:
•-XX, -X mean standardized parts, so they may
have some differences from the original one.
•Items marked “*”are not stocked since they
are seldom required for routine service. Some
delayshould be anticipatedwhen ordering these
items.
•Themechanical partswith no referencenumber
in the exploded views are not supplied.
•Hardware (# mark) list and accessories and
packing materials are given in the last of this
parts list.
•Abbreviation
CND : Canadian model.
AUS : Australian model.
SP : Singapore model.
MY : Malaysia model.
AR : Argentine model.
G : German model.
SECTION 2
EXPLODEDVIEWS
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
2-1. SA-WMS315 (1)
1
10
3567
9
8
11
4
not supplied @@@
not supplied @@@
12
2
supplied with
RV201, S201
#3
#8
#8
SP1
#2
#2
#9
#7
#7
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 X-4952-542-1 FRAME ASSY, GRILLE
2 X-4952-541-1 PANEL ASSY, FRONT
3 4-973-938-41 KNOB(A), PUSH
4 4-227-298-01 SHEET
5 4-226-228-01 KNOB(VOL)
6 4-226-213-01 INDICATOR
7 1-676-815-11 LED BOARD
8 1-676-814-11 POWER SWITCH BOARD
9 A-4428-531-A CONTROL BOARD,COMPLETE
10 A-4411-960-A CABINET ASSY, SPEAKER
11 4-981-864-01 FOOT
12 4-226-227-01 PACKING (D)
SP1 1-529-593-11 SPEAKER (16cm)
2-2. SA-WMS315 (2)
#3
#3
#3
#3
#4
#4
#4
#6
not supplied
not supplied
not supplied
T101
53
54
51
55
56
52 (UK)
52 (AUS)
52 (AR)
52 (US, CND, AEP, MY, SP, G)
57 (SP, MY)
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 1-676-813-11 POWER BOARD
052 1-696-571-21 CORD, POWER (UK)
052 1-696-845-31 CORD, POWER (AUS)
052 1-782-603-11 CORD, POWER (US,CND,AEP,MY,SP,G)
052 1-783-941-21 CORD, POWER (AR)
*53 3-703-244-00 BUSHING (2104), CORD
54 4-227-118-11 PANEL, REAR (US,CND)
54 4-227-118-21 PANEL, REAR (EXCEPT US,CND)
55 A-4428-530-A MAIN BOARD,COMPLETE
*56 3-701-946-23 LABEL, FUSE RATING (US,CND)
057 1-569-008-21 ADAPTOR, CONVERSION 2P (SP,MY)
0T101 1-435-335-11 TRANSFORMER, POWER (US,CND)
0T101 1-435-336-11 TRANSFORMER, POWER (AEP,UK,G)
0T101 1-435-337-11 TRANSFORMER, POWER (AR,MY,SP,AUS)
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièceportant lenumérospécifié.

7
2-3. SS-CN315
101
not supplied @@@
not supplied @@@
103
105
104
SP2
SP3
102
106
106
106
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101 X-4952-576-1 GRILLE (CN) ASSY, FRONT
102 3-703-564-31 SCREW (3.5)
103 X-4952-577-1 CABINET (CN) ASSY
104 1-694-516-11 TERMINAL, SPEAKER
105 4-226-378-01 PANEL (CN), FRONT
106 4-226-531-01 SCREW (3.5 X 62), +P TAPPING
SP2 1-529-596-11 SPEAKER (5X10cm)
SP3 1-529-596-11 SPEAKER (5X10cm)

8
2-4. SS-V315
151
SP4
155
#1
153
154
not supplied
152
156
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
151 X-4952-570-1 GRILLE (SR) ASSY, FRONT
152 3-703-564-31 SCREW (3.5)
153 X-4952-571-1 CABINET (SR) ASSY
154 1-694-516-11 TERMINAL, SPEAKER
155 4-226-307-01 PANEL (SR), FRONT
156 4-226-531-01 SCREW (3.5 X 62), +P TAPPING
SP4 1-529-595-11 SPEAKER (5X10cm)

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
9
SECTION 3
ELECTRICAL PARTS LIST
NOTE:
•Due to standardization, replacements in the
parts list may be different from the parts
specifiedin the diagrams or the components
used on the set.
•-XX, -X mean standardized parts, so they
may have some difference from the original
one.
•Items marked “*”are not stocked since they
are seldom required for routine service.
Some delay should be anticipated when
ordering these items.
•CAPACITORS:
uF: µF
•COILS
uH: µH
•RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable
•Abbreviation
CND : Canadian model.
AUS : Australian model.
SP : Singapore model.
MY : Malaysia model.
AR : Argentine model.
G : German model.
•SEMICONDUCTORS
In each case, u: µ, for example:
uA...: µA... , uPA... , µPA... ,
uPB... , µPB... , uPC... , µPC... ,
uPD..., µPD...
When indicating parts by reference number,
please include the board name.
The components identified by mark 0or
dotted line with mark 0are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
A-4428-531-A CONTROL BOARD, COMPLETE
************************
< CAPACITOR >
C201 1-162-282-31 CERAMIC 100PF 10% 50V
C202 1-131-679-31 MYLAR 0.01UF 5% 50V
C203 1-126-964-11 ELECT 10uF 20.00% 50V
C204 1-126-964-11 ELECT 10uF 20.00% 50V
C205 1-126-964-11 ELECT 10uF 20.00% 50V
C206 1-126-964-11 ELECT 10uF 20.00% 50V
C207 1-130-495-00 MYLAR 0.1uF 5% 50V
C208 1-130-495-00 MYLAR 0.1uF 5% 50V
C209 1-131-679-31 MYLAR 0.01uF 5% 50V
< CONNECTOR >
*CN201 1-564-511-11 PLUG, CONNECTOR 8P
*CN202 1-565-505-11 CONNECTOR, BOARD TO BOARD 14P
< IC >
IC201 8-759-634-50 IC M5218AL
< RESISTOR >
R201 1-249-429-11 CARBON 10K 5% 1/4W
R202 1-249-409-11 CARBON 220 5% 1/4W F
R203 1-249-429-11 CARBON 10K 5% 1/4W
R204 1-249-429-11 CARBON 10K 5% 1/4W
R205 1-249-391-11 CARBON 6.8 5% 1/4W F
R206 1-249-433-11 CARBON 22K 5% 1/4W
R207 1-249-409-11 CARBON 220 5% 1/4W F
< VARIABLE RESISTOR >
RV201 1-225-826-11 RES, VAR, CARBON 20K (LEVEL)
< SWITCH >
S201 1-771-632-11 SWITCH, ROTARY (MODE)
**************************************************************
1-676-815-11 LED BOARD
**********
< CONNECTOR >
*CN801 1-564-505-11 PLUG, CONNECTOR 2P
< DIODE >
D801 8-719-038-54 DIODE SEL6414E-LC05 (POWER)
**************************************************************
A-4428-530-A MAIN BOARD, COMPLETE
*********************
< CAPACITOR >
0C2 1-113-925-11 CERAMIC 0.01uF 20.00% 250V
C101 1-162-286-31 CERAMIC 220PF 10% 50V
C102 1-162-286-31 CERAMIC 220PF 10% 50V
C103 1-162-286-31 CERAMIC 220PF 10% 50V
C104 1-126-964-11 ELECT 10uF 20.00% 50V
C105 1-162-286-31 CERAMIC 220PF 10% 50V
C106 1-162-286-31 CERAMIC 220PF 10% 50V
C107 1-136-167-00 MYLAR 0.15uF 5.00% 50V
C108 1-136-159-00 MYLAR 0.033uF 5.00% 50V
C109 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C110 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C111 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C112 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C113 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C114 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C115 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C301 1-126-964-11 ELECT 10uF 20.00% 50V
C302 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C303 1-126-964-11 ELECT 10uF 20.00% 50V
C304 1-126-934-11 ELECT 220uF 20.00% 10V
C305 1-162-294-31 CERAMIC 0.001uF 10% 50V
C306 1-162-211-31 CERAMIC 33PF 5% 50V
C307 1-162-194-31 CERAMIC 3.9PF 10.00% 50V
C308 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C309 1-104-665-11 ELECT 100uF 20.00% 10V
C310 1-126-963-11 ELECT 4.7uF 20.00% 50V
C311 1-104-664-11 ELECT 47uF 20.00% 25V
C312 1-128-551-11 ELECT 22uF 20.00% 63V
C313 1-128-551-11 ELECT 22uF 20.00% 63V
C314 1-162-282-31 CERAMIC 100PF 10% 50V
C501 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C502 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C503 1-119-940-51 ELECT 4700uF 20.00% 50V
C504 1-119-940-51 ELECT 4700uF 20.00% 50V
C505 1-126-933-11 ELECT 100uF 20.00% 16V
C506 1-126-933-11 ELECT 100uF 20.00% 16V
C507 1-126-964-11 ELECT 10uF 20.00% 50V
C508 1-126-964-11 ELECT 10uF 20.00% 50V
C509 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C510 1-136-165-00 MYLAR 0.1uF 5.00% 50V
CONTROL LED MAIN

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
10
C511 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C512 1-136-165-00 MYLAR 0.1uF 5.00% 50V
< CONNECTOR >
*CN101 1-564-511-11 PLUG, CONNECTOR 8P
*CN301 1-564-510-11 PLUG, CONNECTOR 7P
*CN302 1-565-792-11 PIN, CONNECTOR 2P
*CN501 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
*CN502 1-564-687-11 PIN, CONNECTOR 3P
< DIODE >
D101 8-719-991-33 DIODE 1SS133T-77
D102 8-719-991-33 DIODE 1SS133T-77
D103 8-719-991-33 DIODE 1SS133T-77
D104 8-719-991-33 DIODE 1SS133T-77
D301 8-719-991-33 DIODE 1SS133T-77
D302 8-719-991-33 DIODE 1SS133T-77
D303 8-719-991-33 DIODE 1SS133T-77
D501 8-719-025-03 DIODE RBA-402
D502 8-719-933-80 DIODE HZS12C2L
D503 8-719-933-80 DIODE HZS12C2L
< FUSE >
0F501 1-532-436-11 FUSE, GLASS TUBE 2.5A/125V (US,CND)
0F501 1-532-463-31 FUSE 2A/125V (EXCEPT US,CND)
< IC >
IC101 8-759-634-50 IC M5218AL
IC102 8-759-634-50 IC M5218AL
IC103 8-759-634-50 IC M5218AL
IC301 8-749-011-16 IC STK350-230
IC302 8-759-111-68 IC uPC1237HA
< JACK >
J101 1-785-795-11 JACK, PIN 2P (LINE)
< TRANSISTOR >
Q101 8-729-178-55 TRANSISTOR 2SC2785-E
Q102 8-729-178-55 TRANSISTOR 2SC2785-E
Q103 8-729-178-55 TRANSISTOR 2SC2785-E
Q303 8-729-029-66 TRANSISTOR DTC114ES
< RESISTOR >
R101 1-249-425-11 CARBON 4.7K 5% 1/4W F
R102 1-249-425-11 CARBON 4.7K 5% 1/4W F
R103 1-249-437-11 CARBON 47K 5% 1/4W
R104 1-249-437-11 CARBON 47K 5% 1/4W
R105 1-249-429-11 CARBON 10K 5% 1/4W
R106 1-249-429-11 CARBON 10K 5% 1/4W
R107 1-249-429-11 CARBON 10K 5% 1/4W
R108 1-249-429-11 CARBON 10K 5% 1/4W
R109 1-249-417-11 CARBON 1K 5% 1/4W F
R110 1-249-417-11 CARBON 1K 5% 1/4W F
R111 1-249-429-11 CARBON 10K 5% 1/4W
R112 1-249-417-11 CARBON 1K 5% 1/4W F
R113 1-249-417-11 CARBON 1K 5% 1/4W F
R114 1-249-441-11 CARBON 100K 5% 1/4W
R115 1-249-429-11 CARBON 10K 5% 1/4W
R116 1-247-843-11 CARBON 3.3K 5% 1/4W
R117 1-249-424-11 CARBON 3.9K 5% 1/4W F
R118 1-249-436-11 CARBON 39K 5% 1/4W
R119 1-249-417-11 CARBON 1K 5% 1/4W F
R120 1-249-435-11 CARBON 33K 5% 1/4W
R121 1-249-425-11 CARBON 4.7K 5% 1/4W F
R122 1-249-440-11 CARBON 82K 5% 1/4W
R123 1-249-417-11 CARBON 1K 5% 1/4W F
R124 1-249-435-11 CARBON 33K 5% 1/4W
R125 1-249-426-11 CARBON 5.6K 5% 1/4W
R126 1-249-435-11 CARBON 33K 5% 1/4W
R127 1-249-440-11 CARBON 82K 5% 1/4W
R128 1-249-424-11 CARBON 3.9K 5% 1/4W F
R129 1-249-427-11 CARBON 6.8K 5% 1/4W F
R130 1-249-427-11 CARBON 6.8K 5% 1/4W F
R131 1-249-441-11 CARBON 100K 5% 1/4W
R132 1-249-429-11 CARBON 10K 5% 1/4W
R133 1-249-429-11 CARBON 10K 5% 1/4W
R301 1-249-427-11 CARBON 6.8K 5% 1/4W F
R302 1-249-441-11 CARBON 100K 5% 1/4W
R303 1-249-401-11 CARBON 47 5% 1/4W F
R304 1-249-438-11 CARBON 56K 5% 1/4W
R305 1-249-438-11 CARBON 56K 5% 1/4W
R306 1-249-416-11 CARBON 820 5% 1/4W F
R307 1-249-413-11 CARBON 470 5% 1/4W F
0R308 1-212-857-00 FUSIBLE 10 5% 1/4W
R309 1-249-441-11 CARBON 100K 5% 1/4W
R310 1-249-441-11 CARBON 100K 5% 1/4W
R311 1-249-427-11 CARBON 6.8K 5% 1/4W F
R312 1-249-429-11 CARBON 10K 5% 1/4W
R313 1-215-894-11 METAL OXIDE 2.2K 5% 2W
R314 1-249-439-11 CARBON 68K 5% 1/4W
R315 1-249-430-11 CARBON 12K 5% 1/4W
R316 1-215-868-00 METAL OXIDE 680 5% 1W
0R317 1-247-688-11 CARBON 10 5% 1/4W F
0R318 1-247-688-11 CARBON 10 5% 1/4W F
R501 1-216-457-00 METAL OXIDE 1.2K 5% 2W
R502 1-216-457-00 METAL OXIDE 1.2K 5% 2W
< RELAY >
RY301 1-515-920-11 RELAY (24V)
< TERMINAL >
TM101 1-537-922-11 TERMINAL BOARD (SPEAKER)
**************************************************************
1-676-813-11 POWER BOARD
*************
< CAPACITOR >
C401 1-104-664-11 ELECT 47uF 20.00% 25V
< CONNECTOR >
*CN401 1-770-318-11 PIN, CONNECTOR 7P
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièceportantlenumérospécifié.
POWERMAIN

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
11
< TRANSISTOR >
Q401 8-729-141-30 TRANSISTOR 2SC3623ATP-LK
Q402 8-729-119-76 TRANSISTOR 2SA1115TP-EF
Q403 8-749-010-25 IC MN2488-OPY-M
Q404 8-749-010-26 IC MP1620-OPY-M
< RESISTOR >
R401 1-249-437-11 CARBON 47K 5% 1/4W
R402 1-249-421-11 CARBON 2.2K 5% 1/4W F
R403 1-249-414-11 CARBON 560 5% 1/4W F
0R404 1-247-703-11 CARBON 180 5% 1/4W F
0R405 1-247-703-11 CARBON 180 5% 1/4W F
0R406 1-217-151-00 METAL 0.22 10% 2W
0R407 1-217-151-00 METAL 0.22 10% 2W
**************************************************************
1-676-814-11 POWER SWITCH BOARD
********************
< CAPACITOR >
0C1 1-113-925-11 CERAMIC 0.01uF 20.00% 250V
< CONNECTOR >
CN1 1-564-321-00 PIN, CONNECTOR 2P
< SWITCH >
0S1 1-554-920-61 SWITCH, PUSH (AC POWER)(1 KEY)(POWER)
**************************************************************
MISCELLANEOUS
**************
052 1-696-571-21 CORD, POWER (UK)
052 1-696-845-31 CORD, POWER (AUS)
052 1-782-603-11 CORD, POWER (US,CND,AEP,MY,SP,G)
052 1-783-941-21 CORD, POWER (AR)
104 1-694-516-11 TERMINAL, SPEAKER
154 1-694-516-11 TERMINAL, SPEAKER
0T101 1-435-335-11 TRANSFORMER, POWER (US,CND)
0T101 1-435-336-11 TRANSFORMER, POWER (AEP,UK,G)
0T101 1-435-337-11 TRANSFORMER, POWER (AR,MY,SP,AUS)
SP1 1-529-593-11 SPEAKER (16cm)
SP2 1-529-596-11 SPEAKER (5X10cm)
SP3 1-529-596-11 SPEAKER (5X10cm)
SP4 1-529-595-11 SPEAKER (5X10cm)
**************************************************************
ACCESSORIES & PACKING MATERIALS
*******************************
1-769-329-21 CORD, CONNECTION (PIN-PIN)
1-769-433-11 CORD, SPEAKER (WMS315)
1-769-433-21 CORD, SPEAKER
4-226-697-11 MANUAL, INSTRUCTION
(ENGLISH/SPANISH)(US,UK,SP,MY)
4-226-697-21 MANUAL, INSTRUCTION
(ENGLISH/FRENCH)(AEP,CND,AR,G,AUS)
4-226-697-31 MANUAL, INSTRUCTION
(GERMAN/SPANISH/DUTCH/SWEDISH/ITALIAN/
PORTUGUESE/DANISH/FINNISH/POLISH/RUSIAN)(AEP,G)
4-226-697-41 MANUAL, INSTRUCTION
(SPANISH/CHINESE)(SP,MY,AR)
4-972-322-01 FOOT (Y)
**************************************************************
**************
HARDWARE LIST
**************
#2 7-685-165-01 SCREW +PTP 4X25 TYPE1
#3 7-685-647-79 SCREW +P 3X10 TYPE2 NON-SLIT
#4 7-685-648-79 SCREW +P 3X12 TYPE2 NON-SLIT
#6 7-685-660-19 SCREW +BVTP 4X10 TYPE2 N-S
#7 7-685-663-79 SCREW +BVTP 4X16 TYPE2 N-S
#8 7-685-664-79 SCREW +PTP 4X20 TYPE1
#9 7-685-665-79 SCREW +BVTP 4X25 TYPE2 N-S
POWER
The components identified by
mark 0or dotted line with mark
0are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0sont critiques
pour la sécurité.
Ne les remplacer que par une
pièceportantlenumérospécifié.
POWER SWITCH

SA-VE312/VE315/WMS315/SS-CN315/V315
12
Sony Corporation
Home Audio Division Company
9-929-075-11 2000B1685-1
Printed in Japan © 2000.2
Published by Quality Assurance Dept.