Sony PWS-110RX1A User manual

NETWORK RX STATION
PWS-110RX1A
OPTIONAL POWER SUPPLY
PWSK-101
SERVICE MANUAL
1st Edition

警告
このマニュアルは，サービス専用です。
お客様が，このマニュアルに記載された設置や保守，点検，修理などを行うと感電や火災，
人身事故につながることがあります。
危険をさけるため，サービストレーニングを受けた技術者のみご使用ください。
WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
Model Name Serial No.
PWS-110RX1 (SY) 121001 and Higher
PWS-110RX1 (CN) 521001 and Higher
安全のために，周辺機器を接続する際は，過大電圧を
持つ可能性があるコネクターを以下のポートに接続し
ないでください。
:LAN1コネクター
:LAN2コネクター
:REMOTE1/2コネクター
:REMOTE3/4コネクター
:REMOTE5コネクター
上記のポートについては本書の指示に従ってください。
For safety, do not connect the connector for peripheral
device wiring that might have excessive voltage to the
following port(s).
: LAN 1 connector
: LAN 2 connector
: REMOTE 1/2 connector
: REMOTE 3/4 connector
: REMOTE 5 connector
Follow the instructions for the above port(s).
PWS-110RX1A

CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type rec-
ommended by the manufacturer.
When you dispose of the battery, you must obey the
law in the relative area or country.
ATTENTION
Il y a danger d’explosion s’il y a remplacement incor-
rect de la batterie. Remplacer uniquement avec
une batterie du même type ou d’un type équivalent
recommandé par le constructeur.
Lorsque vous mettez la batterie au rebut, vous devez
respecter la législation en vigueur dans le pays ou la
région où vous vous trouvez.
VORSICHT
Explosionsgefahr bei Verwendung falscher Batterien.
Batterien nur durch den vom Hersteller empfohlenen
oder einen gleichwertigen Typ ersetzen.
Wenn Sie die Batterie entsorgen, müssen Sie die
Gesetze der jeweiligen Region und des jeweiligen
Landes befolgen.
注意
指定以外の電池に交換すると，破裂する危険があり
ます。
必ず指定の電池に交換してください。
使用済みの電池は，国または地域の法令に従って
処理してください。
FÖRSIKTIGHET!
Fara för explosion vid felaktigt placerat batteri.
Byt endast mot samma eller likvärdig typ av batteri,
enligt tillverkarens rekommendationer.
När du kasserar batteriet ska du följa rådande lagar
för regionen eller landet.
PAS PÅ
Fare for eksplosion, hvis batteriet ikke udskiftes
korrekt.
Udskift kun med et batteri af samme eller tilsvarende
type, som er anbefalet af fabrikanten.
Når du bortskaffer batteriet, skal du følge
lovgivningen i det pågældende område eller land.
HUOMIO
Räjähdysvaara, jos akku vaihdetaan virheellisesti.
Vaihda vain samanlaiseen tai vastaavantyyppiseen,
valmistajan suosittelemaan akkuun.
Noudata akun hävittämisessä oman maasi tai
alueesi lakeja.
FORSIKTIG
Eksplosjonsfare hvis feil type batteri settes i.
Bytt ut kun med samme type eller tilsvarende
anbefalt av produsenten.
Kasser batteriet i henhold til gjeldende avfallsregler.
⌞ᝅ
⌞ᝅ
ྸ󰵳ᴪᦘⲺ⭫⊖у↙⺤θቧՐᴿ⠼⛮Ⲻধ䲟Ⱦ
ᴪᦘж㊱ශᡌ࡬䙖୼᧞㦆Ⲻ⭫⊖ශȾ
༺⨼⭫⊖ᰬθᗻ亱䚫ᆾ⴮ީ൦ᡌളᇬⲺ⌋ᗁȾ
PWS-110RX1A

A
ttention-when the product is installed in Rack:
1. Prevention against overloading of branch circuit
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
make sure that the rack does not overload the supply
circuit.
2. Providing protective earth
When this product is installed in a rack and is
supplied power from an outlet on the rack, please
confirm that the outlet is provided with a suitable
protective earth connection.
3. Internal air ambient temperature of the rack
When this product is installed in a rack, please make
sure that the internal air ambient temperature of the
rack is within the specified limit of this product.
4. Prevention against achieving hazardous
condition due to uneven mechanical loading
When this product is installed in a rack, please
make sure that the rack does not achieve hazardous
condition due to uneven mechanical loading.
5. Install the equipment while taking the operating
temperature of the equipment into consideration
For the operating temperature of the equipment, refer
to the specifications of the Operation Manual.
6. When performing the installation, keep the
following space away from walls in order to
obtain proper exhaust and radiation of heat.
Right, Left: 4 cm (1.6 inches) or more
Rear: 10 cm (3.9 inches) or more
本機をラックに設置するとき
熱の適切な排気・発散を得るために，ラックと本機の間
には，以下の空間を確保してください。
・左右両側面 4cm 以上
・後面 10cm 以上
設置時には，通気やサービス性を考慮して設置スペース
を確保してください。
･ファンの排気部( リアパネル面，右側面後ろ側 )，トッ
プパネル後ろ側 )や通気孔( フロントパネル面，左側
面フロント側 )をふさがない。
･通気のために，セット周辺に空間をあける。
･作業エリアを確保するため，セットの左側面および右
側面は4cm以上，セット後方は40cm以上の空間を
あける。
机上などの平面に設置する場合は，左側面および右側面
は4cm以上の空間をそれぞれ確保してください。ただ
し，セット上部はサービス性を考慮し40cm以上の空
間を確保することを推奨します。
When installing, the installation space must be secured
in consideration of the ventilation and service operation.
･Do not block the fan exhaust areas (rear panel and
rear part of the right side panel and rear part of the top
panel) and vents (front panel, front part of the left side
panel) with objects.
･Leave a space around the unit for ventilation.
･Secure working spaces (at least 4 centimeters from
the left panel and right panel and at least 40 centime-
ters from the rear panel of the unit).
When the unit is installed on the desk or the like, leave at
least 4 centimeters of space in the left and right sides.
Leaving 40 centimeters or more of space above the unit
is recommended for service operation.
PWS-110RX1A

Table of Contents
Manual Structure
Purpose of this manual....................................................................................................................5
Related manuals...........................................................................................................................5
Trademarks................................................................................................................................5
Extended equipment...................................................................................................................... 5
1. Service Overview
1-1. Location of Boards and Circuit Configuration................................................................................1-1
1-2. Onboard Switch Settings, LED Functions, and Sensor Functions............................................................1-2
1-2-1. Onboard Switch Settings............................................................................................... 1-2
1-2-2. Functions of Onboard LEDs............................................................................................1-4
1-2-3. Functions of Onboard Sensors..........................................................................................1-8
1-3. LED Indicator of Power Unit................................................................................................. 1-9
1-4. Software Update............................................................................................................. 1-10
1-4-1. Uninstallation of Application Software...............................................................................1-10
1-4-2. Installing Application Software ...................................................................................... 1-11
1-4-3. Software Version Check after Update.................................................................................1-13
1-5. Software Update (for This System)..........................................................................................1-15
1-5-1. Updating Software for the HPR-48 Board............................................................................ 1-15
1-5-2. Updating the Application for This System............................................................................1-18
1-6. Recovery Methods...........................................................................................................1-21
1-6-1. Recovery by the Standard Feature of Windows.......................................................................1-21
1-6-2. Recovery by Using the Windows PE..................................................................................1-24
1-6-3. Recovery by Replacing SSD Module.................................................................................1-26
1-7. Tools and Fixtures............................................................................................................1-27
1-8. Circuit Protection Part List...................................................................................................1-28
1-8-1. Circuit Protection Element............................................................................................1-28
1-8-2. Replacing Fuses.......................................................................................................1-28
1-9. Coaxial Cable................................................................................................................ 1-30
1-9-1. Disconnecting/Connecting Fine-Wire Coaxial Cable.................................................................1-30
2. Error Messages
2-1. Overview of Error Message...................................................................................................2-1
2-1-1. Error Codes.............................................................................................................2-1
2-1-2. Warnings................................................................................................................2-2
2-2. SNMP Trap Messages.........................................................................................................2-3
3. Maintenance Menu
3-1. Maintenance Web Screen..................................................................................................... 3-1
3-1-1. Displaying Maintenance Web Screen.................................................................................. 3-1
PWS-110RX1A 1

4. Periodic Maintenance and Inspection
4-1. Periodic Maintenance......................................................................................................... 4-1
4-1-1. Digital Hours Meter.................................................................................................... 4-1
4-1-2. Periodic Replacement Parts.............................................................................................4-1
5. Replacement of Main Parts
5-1. Precautions before Work...................................................................................................... 5-1
5-1-1. Non-reusable Parts......................................................................................................5-1
5-1-2. Tightening Torque...................................................................................................... 5-1
5-2. Actions to Be Taken Before/After Replacement..............................................................................5-2
5-2-1. Lithium Battery.........................................................................................................5-2
5-2-2. SSD Module (M.2 Assembly)..........................................................................................5-2
5-2-3. After Replacing the M.2 Assembly.....................................................................................5-2
5-2-4. After Replacing the HPR-48 Board.................................................................................... 5-2
5-2-5. After Replacing the MB-1204 Board...................................................................................5-2
5-2-6. After Replacing the iAP Board Assembly..............................................................................5-2
5-2-7. Example of Creating Bootable USB Memory..........................................................................5-4
5-3. Location of Main Parts........................................................................................................5-5
5-4. Top Panel Assembly...........................................................................................................5-7
5-5. Front Panel Assembly.........................................................................................................5-8
5-6. LED-527 Board............................................................................................................... 5-9
5-7. SW-1627 Board..............................................................................................................5-10
5-8. DIO-98 Board................................................................................................................5-11
5-9. Power Unit...................................................................................................................5-12
5-10. Hot-Swap Unit...............................................................................................................5-14
5-11. HPR-48 Board............................................................................................................... 5-15
5-12. Fan Assembly................................................................................................................5-19
5-13. Lithium Battery.............................................................................................................. 5-20
5-14. CN-3698 Board.............................................................................................................. 5-21
5-15. RC-110 Board................................................................................................................5-23
5-16. SSD Module (M.2)...........................................................................................................5-24
5-17. iAP-005 Board Assembly....................................................................................................5-25
5-18. CPU.......................................................................................................................... 5-28
5-19. Memory Module (260pin SO-DIMM).......................................................................................5-32
5-20. IF-1330 Board................................................................................................................5-33
5-21. CN-3934 Board.............................................................................................................. 5-35
5-22. MB-1204 Board..............................................................................................................5-36
6. Spare Parts
6-1. Note on Repair Parts.......................................................................................................... 6-1
6-2. Exploded Views............................................................................................................... 6-2
Overall............................................................................................................................... 6-2
Main Block-1........................................................................................................................ 6-3
Main Block-2........................................................................................................................ 6-4
iAP-005 Block....................................................................................................................... 6-5
6-3. Supplied Accessories..........................................................................................................6-6
PWS-110RX1A 2

7. Block Diagrams and Frame Wiring
Overall..................................................................................................................................7-1
Revision History
PWS-110RX1A 3

Manual Structure
Purpose of this manual
This manual is intended for the use of the system engineers and the service engineers, and provides the limited
information for block service and the information related to maintenance of the unit, such as service overview, error
messages, maintenance menu, periodic maintenance and inspection, and replacement of main parts.
Related manuals
The following manual is provided for this unit in addition to this “Service Manual”.
• Operation Manual (Supplied with this unit)
This manual contains information required to operate and use the unit.
• Installation Manual (Supplied with this unit)
This manual provides information required for delivery and installation of this unit.
• PWS-100 Maintenance Web Application Operation Manual (Supplied with this unit)
Maintenance Web Application is a software that is required for maintenance of this unit.
Trademarks
Trademarks and registered trademarks described in this manual are as follows.
• Windows is a registered trademark or a trademark of Microsoft Corporation in the United States and other countries.
• Google Chrome™ is a trademark of Google Inc.
• The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
Other system names and product names written in this manual are usually registered trademarks or trademarks of
respective development manufacturers.
Extended equipment
Equipment including power supply unit (option PWSK-101) can be additionally installed in this unit. Information on
optional equipment that is not equipped as standard may be provided in “Service Overview” - “Replacement of Main
Parts” in this manual.
PWS-110RX1A 5

Section 1
Service Overview
1-1. Location of Boards and Circuit Configuration
8
9
7
5
1
3
6
2
4
Location No. Board Name Circuit Function
1 LED-527 Front Panel LED
2 MB-1204 PCIe Switch, Storage Block
3 SW-1627 Power SW Panel
4 RC-110 PCI Express Riser Card
5 DIO-98 USB3.0 Output
6 CN-3698 Rear Connector
7 HPR-48 XAVC 4K/HD Codec Card
8 IF-1330 CPU Board Interface
9 CN-3934 Internal Connector
PWS-110RX1A 1-1

1-2. Onboard Switch Settings, LED Functions, and Sensor Functions
1-2-1. Onboard Switch Settings
HPR-48 Board
S3700 S4002
HPR-48 board (side A)
Ref. No. Bit Name Description Factory Setting
S3700 - RESET Factory use -
S4002 1 MAIN BOARD ID OFF
2 OFF
3 OFF
4 OFF
5 Factory use OFF
6 ON: Activated in the PEC4 Back Up Mode.
OFF: Activated in the PEC4 Normal Mode.
OFF
7 ON: Activated in the CPU Back Up Mode.
OFF: Activated in the CPU Normal Mode.
OFF
8 Factory use OFF
PWS-110RX1A 1-2

IF-1330 Board
S800
IF-1330 board (side A)
Ref. No. Bit Name Description Factory Setting
S800 - POWER Factory use -
MB-1204 Board
MB-1204 board (side A)
S2201
S2200
S800 S902
Ref. No. Bit Name Description Factory Setting
S800 1-8 - Factory use OFF (ALL)
S902 - RESET Factory use -
S2200 - RESET Factory use -
Continued
PWS-110RX1A 1-3

Ref. No. Bit Name Description Factory Setting
S2201 1 CFG ON : RAID doesn't work
OFF : RAID works
OFF (ALL)
2 ON: Activates IC1000 in the Backup Mode.
OFF: Activates IC1000 in the Normal Mode.
3 ON: Activates IC2400 in the Backup Mode.
OFF: Activates IC2400 in the Normal Mode
4 Factory use
1-2-2. Functions of Onboard LEDs
HPR-48 Board
D3700
D3701
D2503 D2502 D2501 D2500 D6100 D6101 D6102
HPR-48 board (side A)
Ref. No. Name Color Description Normal State
(Power On)
D3700 CFG4 Green Lights when the CFG4 configuration has been suc-
cessfully completed.
Lit
D3701 Factory use Blinks
D6102 LOCK Green Factory use Lit
D6101 Lit
D6100 Lit
D2500 PEC4 Green Factory use Off
D2501 Off
D2502 Off
D2503 Lights when the CFG4 configuration has been suc-
cessfully completed.
Lit
PWS-110RX1A 1-4

IF-1330 Board
D1007 D1008
IF-1330 board (side A)
Ref. No. Name Color Description Normal State
(Power On)
D1006 3.3 V power supply in-
dicator
Yellow green Lights when the 3.3 V power is on. Lit
D1007 3.3 VSB power supply
indicator
Yellow green Lights when the 3.3 VSB power is on. Lit
MB-1204 Board
MB-1204 board (side A)
D903
D2300
D1803
D1802
D1801
D1800
D2400
D2203D2201
D2202
D2200
D808
D807
D806
D805
D804
D803
D802
D801
PWS-110RX1A 1-5

Ref. No. Name Color Description Normal State
(Power On)
D801 - Orange Factory use Indeterminate
D802
D803
D804
D805
D806
D807
D808
D903 - Green Lights when the IC900 configuration has been suc-
cessfully completed.
Lit
D1800 - Green Factory use Off
D1801
D1802
D1803
D2200 CFG DONE Green Lights when the IC2200 configuration has been
successfully completed.
Lit
D2201 CFG0 Green Factory use Blinks
D2202 CFG1 Green Factory use Off
D2203 CFG2 Green Factory use Lit
D2300 FLASH
BUSY
Green Factory use Off
D2400 IMX6 Green Factory use Blinks
SW-1627 Board
D101 D103
D102
D106
D108 D111
SW-1627 board (side A)
D107
D110
D104
D105
D109
Ref. No. Name Color Description Normal State
(Power On)
D101 ERROR LED Red Indicates an abnormality in fan assembly FAN1*1
Normal: Off
Abnormal: Red
Off
D102 Red Indicates an abnormality in fan assembly FAN2*1
Normal: Off
Abnormal: Red
Off
Continued
*1: For location of Fan 1 to 5, Power unit A and B, refer to “5-3. Location of Main Parts”.
PWS-110RX1A 1-6

Ref. No. Name Color Description Normal State
(Power On)
D103 Red Indicates an abnormality in fan assembly FAN3*1
Normal: Off
Abnormal: Red
Off
D104 Red Indicates an abnormality in fan assembly FAN4*1
Normal: Off
Abnormal: Red
Off
D105 Red Indicates an abnormality in fan assembly FAN5*1
Normal: Off
Abnormal: Red
Off
D106 Red Indicates an abnormality in power supply A
unit*1(in the right slot viewed from the rear)
Normal: Off
Abnormal: Red
Off
D107 Red Indicates an abnormality in power supply B
unit*1(in the right slot viewed from the rear)
Normal: Off
Abnormal: Red
Off
D108 Red Indicates an abnormality in internal temperature
Normal: Off
Abnormal: Red
Off
D109 POWER Green/Red Power ON/standby indicator Lit green: Operating
Lit red: Standby
Off: Power cable dis-
connected
D110 ACCESS Blue Storage access indicator Lit: Access in progress
Off: No access
D111 SYSTEM Green/
Orange/Red
System indicator
Indicates the unit state.
Lit green: Working nor-
mally
Blinking green (1 Hz):
Startup or shutdown in
progress
Blinking orange (1 Hz):
A warning occurred.
Blinking red (4 Hz): An
error occurred.
*1: For location of Fan 1 to 5, Power unit A and B, refer to “5-3. Location of Main Parts”.
PWS-110RX1A 1-7

1-2-3. Functions of Onboard Sensors
HPR-48 Board
IC2802
IC3901
HPR-48 board (side A)
Board Name Ref. No. Function
HPR-48 IC2802 Temperature sensor
IC3901 Temperature sensor
MB-1204 Board
IC804
MB-1204 board (side A)
IC2402
MB-1204 board (side B)
Board Name Ref. No. Function
MB-1204 IC804 Temperature sensor
IC2402 Temperature sensor
PWS-110RX1A 1-8

1-3. LED Indicator of Power Unit
Power unit is equipped with one LED that indicates the state of power unit.
Lights in green: All outputs (+12V and +5Vsub) are normal.
Off: At least one of the outputs is abnormal.
LED indicator
PWS-110RX1A 1-9

1-4. Software Update
This section describes how to update PWS-100/PWS-110 main unit control application software listed below and the
built-in storage (RAID_PKG).
• Sony SNMP PWS-100
• Sony HKP Service PWS-100
• Sony Web_Application _PWS-100
Equipment required
• A USB mouse
• A USB keyboard
• A monitor
• A USB flash memory (commercially available, 1GB or more recommended)
Required file
• Data file for update (Installation package)
Note
For obtaining the latest data file for update (Installation package), contact your local Sony Sales Office/Service Center.
Preparation
1. Connect the mouse and the keyboard to the USB connectors.
2. Connect the monitor to the HDMI connector.
3. Copy the data file for update (Installation package) to the USB memory.
Note
When updating the application software program, uninstall the previously installed software programs and then install
the new-version software programs.
1-4-1. Uninstallation of Application Software
Before starting reinstallation or version update of software, uninstall installed software programs.
Uninstall the software package PWS-100_Suite to uninstall installed software programs.
1. On the [Control Panel], select “Programs and Features” from [Programs].
On the Programs and Features window, select “PWS-100_Suite” and then click [Uninstall].
PWS-110RX1A 1-10