Sony HCD-SB100 User manual

SERVICE MANUAL
Sony Corporation
Audio Group
Published by Sony Engineering Corporation
US Model
Canadian Model
HCD-SB100
AEP Model
UK Model
E Model
Australian Model
HCD-SB100/SB200
DVD RECEIVER
9-879-182-05
2005D16-1
© 2005.04
Ver. 1.4 2005.04
SPECIFICATIONS
HCD-SB100/SB200
•HCD-SB100/SB200 are the amplifier, DVD/CD and
tuner section in DAV-SB100/SB200.
•Abbreviation
AUS:Australian model
CND : Canadian model
EA : Saudi Arabia model
EE : East European model
RU : Russian model
SP : Singapore model
Photo: HCD-SB100
ManufacturedunderlicensefromDolbyLaboratories.“Dolby”,“ProLogic”,
and the double-D symbol are trademarks of Dolby Laboratories.
Confidential Unpublished works. Copyright 1992-1997 Dolby
Laboratories.All rights reserved.
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 5,956,674, 5,974,380, 5,978,762 and other
worldwidepatentsissued andpending.“DTS”and“DTSDigitalSurround”
areregisteredtrademarks ofDigitalTheaterSystems,Inc.Copyright 1996,
2000 Digital Theater Systems, Inc.All rights reserved.
(SB100: US, CND models)
Power supply 120V AC, 60Hz
Power consumption 70W, No more than 1 W (120V AC) (at the power saving mode)
Mass kg
External dimensions (WxHxD) 430 x 70 x 383.5 mm
Operating conditions Temperature: 5°C to 35°C, Operation status: Horizontal
Operating humidity 5% to 85%
Laser Semiconductor laser, wavelength 650 nm for VCD and DVD,
wavelength 780 nm for CD
Emission duration Continuous
Signal system NTSC 525/60
Frequency response (audio) 2 Hz ~ 20 kHz (±1.0 dB)
Signal-to-noise ratio (audio) More than 75 dB (1 kHz, NOP, 20 kHz LPF/A-Filter)
Dynamic range (audio) More than 70 dB
Harmonic distortion (audio) 0.5 % (1 kHz, at 12W position) (20 kHz LPF/A-Filter)
Inputs (AUDIO IN):
Sensitivity: 800 mV
Impedance: 50 kilohms
Video output 1.0 V (p-p), 75 Ω, negative sync., RCA jack
S VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.286 V (p-p) 75 ohms
COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(P
B /C B )/(P R /C R ) 0.7 V (p-p), 75 ohms, RCA jack x 2
Tuning Range 87.5 - 108 MHz
Intermediate Frequency 10.7 MHz
Signal-to Noise Ratio 60 dB (Mono)
Tuning Range 522 - 1,611 kHz
Intermediate Frequency 450 kHz
Stereo mode 50W + 50W (8 Ωat 1 kHz, THD 10 %)
Surround mode Front:50W + 50W
Centre*: 50W
Surround*: 50W + 50W (8Ωat 1 kHz,THD 10 %)
Subwoofer*: 80W (4Ωat 50 Hz, THD 10 %)
Outputs PHONES: (32 Ω, 25mW)
[General]
[CD/DVD][Video][Amplifier]
(* Depending on the sound mode
settings and the source, there
may be no sound output.)
[Tuner]
[FM]
AM
[MW]
VIDEO
4.7
– Continued on next page –

2
HCD-SB100/SB200
Ver. 1.1
(SB100: AEP, UK, RU, EE models) (SB100: EA, SP, AUS models)
(SB200: AEP, UK, RU, EE models) (SB200: SP, AUS models)
Power supply 220-240V AC, 50/60Hz
Power consumption 70W, No more than 1 W (220-240V AC) (at the power saving mode)
Mass kg
External dimensions (WxHxD) 430 x 70 x 383.5 mm
Operating conditions Temperature: 5°C to 35°C, Operation status: Horizontal
Operating humidity 5% to 85%
Laser Semiconductor laser, wavelength 650 nm for VCD and DVD,
wavelength 780 nm for CD
Emission duration Continuous
Signal system PAL 625/50, NTSC 525/60
Frequency response (audio) 2 Hz ~ 20 kHz (±1.0 dB)
Signal-to-noise ratio (audio) More than 75 dB (1 kHz, NOP, 20 kHz LPF/A-Filter)
Dynamic range (audio) More than 70 dB
Harmonic distortion (audio) 0.5 % (1 kHz, at 12W position) (20 kHz LPF/A-Filter)
Inputs (AUDIO IN):
Sensitivity: 800 mV
Impedance: 50 kilohms
SCART (AUDIO IN):
Sensitivity: 800 mV
Impedance: 50 kilohms
Video output 1.0 V (p-p), 75 Ω, negative sync., RCA jack
EURO AV (TO TV)
Tuning Range 87.5 - 108 MHz
Intermediate Frequency 10.7 MHz
Signal-to Noise Ratio 60 dB (Mono)
Tuning Range 522 - 1,611 kHz
Intermediate Frequency 450 kHz
Stereo mode 50W + 50W (8 Ωat 1 kHz, THD 10 %)
Surround mode Front:50W + 50W
Centre*: 50W
Surround*: 50W + 50W (8Ωat 1 kHz,THD 10 %)
Subwoofer*: 80W (4Ωat 50 Hz, THD 10 %)
Outputs PHONES: (32 Ω, 25mW)
[General]
[CD/DVD][Video][Amplifier]
(* Depending on the sound mode
settings and the source, there
may be no sound output.)
[Tuner]
[FM]
AM
[MW]
VIDEO
4.7
Power supply 220-240V AC, 50/60Hz
Power consumption 70W, No more than 1 W (220-240V AC) (at the power saving mode)
Mass kg
External dimensions (WxHxD) 430 x 70 x 383.5 mm
Operating conditions Temperature: 5°C to 35°C, Operation status: Horizontal
Operating humidity 5% to 85%
Laser Semiconductor laser, wavelength 650 nm for VCD and DVD,
wavelength 780 nm for CD
Emission duration Continuous
Signal system PAL 625/50, NTSC 525/60
Frequency response (audio) 2 Hz ~ 20 kHz (±1.0 dB)
Signal-to-noise ratio (audio) More than 75 dB (1 kHz, NOP, 20 kHz LPF/A-Filter)
Dynamic range (audio) More than 70 dB
Harmonic distortion (audio) 0.5 % (1 kHz, at 12W position) (20 kHz LPF/A-Filter)
Inputs (AUDIO IN):
Sensitivity: 800 mV
Impedance: 50 kilohms
Video output 1.0 V (p-p), 75 Ω, negative sync., RCA jack
S VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.286 V (p-p) 75 ohms
COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(P
B /C B )/(P R /C R ) 0.7 V (p-p), 75 ohms, RCA jack x 2
Tuning Range 87.5 - 108 MHz
Intermediate Frequency 10.7 MHz
Signal-to Noise Ratio 60 dB (Mono)
Frequency Response (AUS) 150 - 10,000 Hz
Tuning Range 522 - 1,611 kHz
Intermediate Frequency 450 kHz
Stereo mode 50W + 50W (8 Ωat 1 kHz, THD 10 %)
Surround mode Front:50W + 50W (THD 10 %)
Centre*: 50W
Surround*: 50W + 50W (8Ωat 1 kHz,THD 10 %)
Subwoofer*: 80W (4Ωat 50 Hz, THD 10 %)
Output PHONES: (32 Ω, 25mW)
[General]
[CD/DVD][Video][Amplifier]
(* Depending on the sound mode
settings and the source, there
may be no sound output.)
[Tuner]
[FM]
AM
[MW]
4.7
VIDEO
Power supply 220-240V AC, 50/60Hz
Power consumption 100W, No more than 1 W (220-240V AC) (at the power saving mode)
Mass kg
External dimensions (WxHxD) 430 x 70 x 370 mm
Operating conditions Temperature: 5°C to 35°C, Operation status: Horizontal
Operating humidity 5% to 85%
Laser Semiconductor laser, wavelength 650 nm forVCD and DVD,
wavelength 780 nm for CD
Emission duration Continuous
Signal system PAL, NTSC
Frequency response (audio) 2 Hz ~ 20 kHz (±1.0 dB)
Signal-to-noise ratio (audio) More than 75 dB (1 kHz, NOP, 20 kHz LPF/A-Filter)
Dynamic range (audio) More than 70 dB
Harmonic distortion (audio) 0.5 % (1 kHz, at 12W position) (20 kHz LPF/A-Filter)
Inputs (AUDIO IN):
Sensitivity: 800 m V
Impedance: 50 kilohms
SCART (AUDIO IN):
Sensitivity: 800 mV
Impedance: 50 kilohms
Video output 1.0 V (p-p), 75 Ω, negative sync., RCA jack
EURO AV (TO TV)
Tuning Range 87.5 - 108 MHz
Intermediate Frequency 10.7 MHz
Signal-to Noise Ratio 60 dB (Mono)
Tuning Range 522 - 1,611 kHz
Intermediate Frequency 450 kHz
Stereo mode 80W + 80W (6 Ωat 1 kHz, THD 10 %)
Surround mode Front: 80W + 80W
Centre*: 80W
Surround*: 80W + 80W (6Ωat 1 kHz,THD 10 %)
Subwoofer*: 150W (3Ωat 50 Hz, THD 10 %)
Outputs PHONES: (32 Ω, 25mW)
[General]
[CD/DVD][Video][Amplifier]
(* Depending on the sound mode
settings and the source, there
may be no sound output.)
[FM]
AM
[MW]
[Tuner]
4.9
VIDEO
Power supply 220-240V AC, 50/60Hz
Power consumption 100W, No more than 1 W (220-240V AC) (at the power saving mode)
Mass kg
External dimensions (WxHxD) 430 x 70 x 370 mm
Operating conditions Temperature: 5°C to 35°C, Operation status: Horizontal
Operating humidity 5% to 85%
Laser Semiconductor laser, wavelength 650 nm for VCD and DVD,
wavelength 780 nm for CD
Emission duration Continuous
Signal system PAL, NTSC
Frequency response (audio) 2 Hz ~ 20 kHz (±1.0 dB)
Signal-to-noise ratio (audio) More than 75 dB (1 kHz, NOP, 20 kHz LPF/A-Filter)
Dynamic range (audio) More than 70 dB
Harmonic distortion (audio) 0.5 % (1 kHz, at 12W position) (20 kHz LPF/A-Filter)
Inputs (AUDIO IN):
Sensitivity: 800 mV
Impedance: 50 kilohms
Video output 1.0 V (p-p), 75 Ω, negative sync., RCA jack
S VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, Mini DIN 4-pin x 1
(C) 0.286 V (p-p) 75 ohms
COMPONENT VIDEO OUT (Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(P
B /C B )/(P R /C R ) 0.7 V (p-p), 75 ohms, RCA jack x 2
Tuning Range 87.5 - 108 MHz
Intermediate Frequency 10.7 MHz
Signal-to Noise Ratio 60 dB (Mono)
Tuning Range 522 - 1,611 kHz
Intermediate Frequency 450 kHz
Stereo mode 80W + 80W (6 Ωat 1 kHz, THD 10 %)
Surround mode Front:80W + 80W
Centre*: 80W
Surround*: 80W + 80W (6Ωat 1 kHz,THD 10 %)
Subwoofer*: 150W (3Ωat 50 Hz, THD 10 %)
Outputs PHONES: (32 Ω, 25mW)
[Tuner] [General]
[CD/DVD][Video][Amplifier]
Designs and specifications are subject to change without notice.
(*
Depending on the sound mode
settings and the source, there
may be no sound output.)
[FM]
AM
[MW]
4.9
VIDEO

3
HCD-SB100/SB200
Ver. 1.1
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0OR DOTTED LINE
WITH MARK 0ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT. NE REMPLACER CES COM- POSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT
DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS
PUBLIÉS PAR SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following
safety check before releasing the set to the customer:
Check the antennaterminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts forAC leakage.
Check leakage as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth ground and
from all exposed metal parts to any exposed metal part having a
return to chassis, must not exceed 0.5 mA (500 microamperes.).
Leakage current can be measured by any one of three methods.
1. Acommercial leakagetester,suchas theSimpson 229or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operatedAC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM orbattery-operatedAC voltmeter.The “limit” indication
is 0.75V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples
of a passiveVOM that is suitable. Nearly all battery operated
digital multimeters that have a 2VAC range are suitable. (See
Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
1.5 k Ω 0.15 µ FAC
voltmeter
(0.75 V)
To Exposed Metal
Parts on Set
Earth Ground
CAUTION
Use of controls or adjustments or performance of procedures
otherthan those specified herein mayresult in hazardousradiation
exposure.
Notes on chip component replacement
•Never reuse a disconnected chip component.
•Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing
•Keep the temperature of the soldering iron around 270 °C
during repairing.
•Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
•Be careful not to apply force on the conductor when soldering
or unsoldering.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
This appliance is classified as
a CLASS 1 LASER product.
The CLASS 1 LASER
PRODUCT MARKING is
located on the rear exterior.

4
HCD-SB100/SB200
Ver. 1.1
TABLE OF CONTENTS
1. SERVICING NOTES ................................................ 5
2. GENERAL ................................................................... 6
3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 12
3-2. Case ................................................................................. 13
3-3. Front Panel Assy Section................................................. 13
3-4. POWER Board ................................................................ 14
3-5. DVD Board...................................................................... 15
3-6. DVD Mechanism Deck ................................................... 16
3-7. Tuner Pack ....................................................................... 16
3-8. AMP Board...................................................................... 17
4. ELECTRICALTROUBLE
SHOOTING GUIDE .................................................. 18
5. TEST MODE ............................................................... 42
6. ELECTRICAL ADJUSTMENT ............................. 43
7. DIAGRAMS
7-1. Block Diagram – DVD Section – ................................... 46
– AUDIO Section –.......................................................... 47
– POWER Section – ........................................................ 48
7-2. Printed Wiring Board
– AMP Section SB100 (Component Side) – ................... 49
7-3. Printed Wiring Board
– AMP Section SB100 (Conductor Side) – ..................... 50
7-4. Printed Wiring Board
– AMP Section SB200 (Component Side) – ................... 51
7-5. Printed Wiring Board
– AMP Section SB200 (Conductor Side) – ..................... 52
7-6. Schematic Diagram – AMP Section (1/6) – ................... 53
7-7. Schematic Diagram – AMP Section (2/6) – ................... 54
7-8. Schematic Diagram – AMP Section (3/6) – ................... 55
7-9. Schematic Diagram – AMP Section (4/6) (SB100) –..... 56
7-10. Schematic Diagram – AMP Section (5/6) (SB200) –..... 57
7-11. Schematic Diagram – AMP Section (6/6) – ................... 58
7-12. Printed Wiring Board – DVD Section – ......................... 59
7-13. Schematic Diagram – DVD Section (1/3) – ................... 60
7-14. Schematic Diagram – DVD Section (2/3) – ................... 61
7-15. Schematic Diagram – DVD Section (3/3) – ................... 62
7-16. Printed Wiring Board – FRONT Section –..................... 63
7-17. Schematic Diagram – FRONT Section – ....................... 64
7-18. Printed Wiring Board – POWER Section (SB100) – ..... 65
7-19. Printed Wiring Board – POWER Section (SB200) – ..... 66
7-20. Schematic Diagram
– POWER Section (1/2) (SB100) –................................. 67
7-21. Schematic Diagram
– POWER Section (2/2) (SB200) –................................. 68
8. EXPLODED VIEWS
8-1. Overall Section ................................................................ 77
8-2. Chassis Section................................................................ 78
8-3. DVD Mechanism Section ................................................ 79
9. ELECTRICAL PARTS LIST .................................. 80

5
HCD-SB100/SB200
Ver. 1.1
SECTION 1
SERVICING NOTES
NOTES ON HANDLINGTHE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
repair parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
Carry out the “S curve check” in “CD section adjustment”and check
that the S curve waveform is output several times.

6
HCD-SB100/SB200 SECTION 2
GENERAL This section is extracted
from instruction manual.
STANDBY
IR
- PRESET +-
VOLUME +
FUNCTION
PHONES
PAUSE (X)
Pause playback of a disc temporarily.
OPEN/CLOSE ( )
Opens or closes the disc tray.
Remote Sensor
Point the DVD receiver remote control here.
Display window
Disc Tray
Insert a disc here.
@ / 1 (POWER) indicator
Switches the DVD Receiver ON and OFF.
STOP (x
.
>
)
Stops playback of a disc.
PLAY (
H
A
)
To play back a disc.
Forward SKIP ( )
DVD: Go to NEXT chapter/track.
RADIO:
To select preset station you want.
Reverse SKIP ( )
DVD: Go to beginning of current chapter/track or to previous
chapter/track.
RADIO:
To select preset station you want.
VOLUME Control
Press “+” to increase volume or press “-” to
decrease the volume.
STANDBY indicator
Lights red when the receiver
is in Standby mode (off). FUNCTION
To select the Receiver’s source.
(FM, AM, VIDEO, TV or
CD/DVD)
PHONES
To connect headphones.
Front Panel Controls
•Abbreviation
AUS:Australian model
CND : Canadian model
EA : Saudi Arabia model
EE : East European model
RU : Russian model
SP : Singapore model

7
HCD-SB100/SB200
(SB100: AEP, UK, RU, EE models)
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
AC Power Cord
Plug into the power source.
SPEAKER CONNECTORS
Connect the six supplied speakers
to these terminals.
FM ANTENNA CONNECTOR
Connect the FM antenna to this terminal.
AM LOOP ANTENNA CONNECTORS
Connect the AM Loop antenna to this terminal.
EURO AV OUTPUT (TOTV)
Connect to your TV set.
VIDEO (AUDIO IN L/R)
Connect the audio output of an external
source (VCR, LD player, etc).
MONITOR OUT (VIDEO)
Connect to a TV with video input.
Rear Panel Connections

8
HCD-SB100/SB200
(SB100: US, CND, EA, SP, AUS models)
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
AC Power Cord
Plug into the power source.
SPEAKER CONNECTORS
Connect the six supplied
speakers to these terminals.
FM ANTENNA CONNECTORS
Connect the FM antenna to this terminal.
AM LOOP ANTENNA CONNECTORS
Connect the AM Loop antenna to this terminal.
VIDEO (AUDIO IN L/R)
Connect the audio output of an external
source (VCR, LD player, etc).
MONITOR OUT (VIDEO)
Connect to a TV with video input.
MONITOR S VIDEO OUT (DVD Only)
Connect to a S Video Input on TV.
FOR DVD VIEWING ONLY.
COMPONENT VIDEO OUT (Y PB/CBPR/CR)
Connect to a TV with Y PB/CBPR/CRinputs.
FOR DVD VIEWING ONLY.
Rear Panel Connections

9
HCD-SB100/SB200
(SB200: AEP, UK, RU, EE models)
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
AC Power Cord
Plug into the power source.
SPEAKER CONNECTORS
Connect the six supplied speakers
to these terminals.
FM ANTENNA CONNECTOR
Connect the FM antenna to this terminal.
AM LOOP ANTENNA CONNECTORS
Connect the AM Loop antenna to this terminal.
EURO AV OUTPUT (TOTV)
Connect to your TV set.
VIDEO (AUDIO IN R/L)
Connect the audio output of an external
source (VCR, LD player, etc).
MONITOR OUT (VIDEO)
Connect to a TV with video input.
Rear Panel Connections

10
HCD-SB100/SB200
(SB200: SP, AUS models)
Rear Panel Connections
Do not touch the inner pins of the jacks on the rear
panel. Electrostatic discharge may cause permanent
damage to the unit.
AC Power Cord
Plug into the power source.
SPEAKER CONNECTORS
Connect the six supplied
speakers to these terminals.
FM ANTENNA CONNECTORS
Connect the FM antenna to this terminal.
AM LOOP ANTENNA CONNECTORS
Connect the AM Loop antenna to this terminal.
VIDEO (AUDIO IN L/R)
Connect the audio output of an external
source (VCR, LD player, etc).
MONITOR OUT (VIDEO)
Connect to a TV with video input.
MONITOR S VIDEO OUT (DVD ONLY)
Connect to a S Video Input on TV.
FOR DVD VIEWING ONLY.
COMPONENT VIDEO OUT (Y P
B /C B P R /C R )
Connect to a TV with Y P
B /C B P R /C R inputs.
FOR DVD VIEWING ONLY.

11
HCD-SB100/SB200
SONY TV DIRECT
Select the output source to DVD directly.
TV @ / 1
Switches TV ON and OFF.
@ / 1
Switches DVD Receiver ON and OFF.
AUTO FORMAT DIRECT
Selects sound mode between A.F.D.
AUTO, PRO LOGIC, PLII MOVIE and
PLII MUSIC.
MODE
Selects sound mode between FLAT,
ROCK, POP, JAZZ, CLASSIC and
NEWS.
FUNCTION
To select the Receiver’s source.
(FM, AM, VIDEO, TV or CD/DVD)
Z
Opens and closes the disc tray.
DSGX
Switches DSGX ON and OFF.
0-9 numerical buttons
Selects numbered options in a menu.
>10/ TV ENTER
Used to control TV.
SLOW t/ TUNING-
For picture search or slow playback back-
ward.
To tune in the desired station.
SLOW T/TUNING+
For picture search or slow playback
forward.
To tune in the desired station.
Playback Control Buttons
•H(PLAY)
Starts playback.
•X(PAUSE)
Pause playback or recording temporarily.
•x(STOP)
Stops playback.
DVD MENU
Accesses menu on a DVD disc.
DISPLAY
To display remaining time between
Chapter and title.
To check the RDS service programme (PS).
VOLUME (+/-)
Adjusts speaker volume.
CLEAR
Removes a track number on the program
menu.
RETURN
Returns the setup menu.
DIMMER
To change the brightness of the display
window.
TV/VIDEO
Selects the TV’s source.
SLEEP
To place the unit in the Sleep mode.
TUNER/BAND
Selects the DVD Receiver’s tuner as the
listening choice. (FM and AM bands)
MUTING
Momentarily silence the speaker of the
DVD Receiver.
TUNER MENU
Memorize a radio station frequency
into the tuner.
Press to clear preset stations from the
tuner memory.
PROGRAM
Enters to the programme edit mode or
exits from that.
REPEAT
Repeat chapter, track, title, all.
FM MODE
To change between MONO and STEREO
modes.
TV
To control TVs with the Remote.
AUDIO
Selects an audio language (DVD) or an
audio channel (CD).
ANGLE
Selects a DVD camera angle if available.
SUBTITLE
Selects a subtitle language.
PREV/PRESET-
Go to beginning of current chapter or
track or go to previous chapter or track.
Select programme of Tuner.
NEXT/PRESET+
Go to next chapter or track.
Select programme of Tuner.
DVD TOP MENU
Displays the disc’s Title menu, if available.
B/b/V/v(left/right/up/down)
Selects an option in the menu.
ENTER
Acknowledges menu selection.
DVD DISPLAY
Accesses On-Screen display.
TV VOL +/–
Adjusts TV’s volume.
TV CH +/–
Selects TV’s channel.
DVD SETUP
Accesses or removes DVD setup menu.
Remote Control

12
HCD-SB100/SB200
Ver. 1.1 SECTION 3
DISASSEMBLY
3-1. DISASSEMBLY FLOW
•This set can be disassembled in the order shown below.
•: In order to remove set AMP board please remove POWER board and DVD board.
3-2. CASE
(Page 13)
3-3. FRONT PANEL ASSY
SECTION
(Page 13)
3-6. DVD MECHANISM
DECK
(Page 16)
SET
3-4. POWER BOARD
(Page 14) 3-5. DVD BOARD (Page 15) 3-7.TUNER PACK
(Page 16)
3-8. AMP BOARD
(Page 17)

13
HCD-SB100/SB200
Ver. 1.1
•Follow the disassembly procedure in the numerical order given.
3-2. CASE
2 two case screws
1 two case screw
s
3 two screws
4 case
3-3. FRONT PANEL ASSY SECTION
4 front panel assy section
3 two claws
3 two claws
3 three claws
3 five claws
3 six claws
3 two claws
1 w ire (flat type)
23p (PN101)
2 w ire (flat type)
24p (PN102)

14
HCD-SB100/SB200
Ver. 1.1
3-4. POWER BOARD
3 four screws
6 POWER board
2 connecto
r
(PN901)
1 connector
(CN903)
5 connector
(CN902)
4 connector
(CN901)

15
HCD-SB100/SB200
Ver. 1.1
3-5. DVD BOARD
1 two screws
2 cover
6 four screws
5 connector
(CN903)
7 connector
(PDA02)
8 connector
(PDA03)
3 w ire (flat type)
23p (PDM01)
4 w ire (flat type)
11p (PDM02)
9 DVD board

16
HCD-SB100/SB200
Ver. 1.1
1 two screws
6 screw
9 door DVD
7 DVD mechanism deck
5 screw
2 cover
3 w ire (flat type)
23p (PDM01)
4 w ire (flat type)
11p (PDM02)
8 two claws
1 w ire (flat type)
12p (CON01)
3 tuner pack
2 two screws
3-6. DVD MECHANISM DECK
3-7. TUNER PACK

17
HCD-SB100/SB200
Ver. 1.1
1 w ire (flat type)
12p (PN103)
7 AMP board
3 two screws
2 two screws
4 two screw
s
6 two screws
5 screw
3-8. AMP BOARD

18
HCD-SB100/SB200
Ver. 1.1 SECTION 4
ELECTRICALTROUBLE SHOOTING GUIDE
INSERT
POWER CORD.
TURN ON
THE RED LED?
IS POWER ON?
CHECK POWER PLUG
AND POWER SUPPLY CIRCUIT.
DOES INITIAL
READ WORK?
DOES IT PLAY?
YES
NO
YES
YES
OK
NO
YES
NO
NO
CHECK POWER SUPPLY CIRCUIT.
CHECK LASER CIRCUIT.
CHECK TRACKING SERVO CIRCUIT.
TURN POWER ON.
CHECK FOCUS CIRCUIT.
CHECK DISC.
DOES IT OUTPUT
AUDIO?
YES
NO
CHECK AUDIO CIRCUIT.
4-1. AUDIO PART
1. POWER CHECK FLOW

19
HCD-SB100/SB200
Ver. 1.1
2. AUDIO µ.COM CIRCUIT
POWER ON
Does it appear
DVD Error at
FLD?
Does other function
name appear at FLD?
Check
Connector(PN902)if
is normally.
Check power part
of Main B/D.
Check oscillator
of x101.
Check if IC101
PIN1 is High.
Check if IC101
PIN11 is High.
Check if IC101 PIN
17, 46, 72, 90 is high
(5V).
Check if IC101
PIN26 is High.
Replace IC101.
Does CD/DVD
appear at FLD?
Reconnet it.
Refer to SMPS
OK.
Refer to oscillator
Circuit.
Check DVD Reset Waveform.
Check IC101 Reset Wavefrom.
Check 5V line.
Check Power dection Circuit.
Does LOADING
appear at FLD?
Does no Dise or
Time appear at FLD?
Check if DVD an Audio
Micom Interface is OK.
Check power.
Check DVD Module.
Check SMPS.
YES
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
YES
YES YES
YES
YES
YES
YES
YES
YES
YES
YES

20
HCD-SB100/SB200
Ver. 1.1
3. FRONT CIRCUIT (1/2)