
— 3 —
TABLE OF CONTENTS
1. SERVICING NOTE .......................................................... 4
2. GENERAL .......................................................................... 5
3. DISASSEMBLY
3-1. Front Panel .......................................................................... 24
3-2. Balance Board, Display Board and Volume Board............. 24
4. ELECTRICAL ADJUSTMENTS ............................... 25
5. DIAGRAMS
5-1. Circuit Boards Location ...................................................... 27
5-2. Block Diagrams
• Dolby Surround Section .................................................. 29
• OSD Section .................................................................... 31
• Power Amp Section ......................................................... 33
• Panel Section ................................................................... 35
• Power Section .................................................................. 37
5-3. Printed Wiring Board — Dolby Surround Section — ........ 40
5-4. Schematic Diagram — Dolby Surround Section — ........... 43
5-5. Schematic Diagram — OSD Section — ............................. 47
5-6. Printed Wiring Board — OSD Section — .......................... 51
5-7. Printed Wiring Board — Power Amp Section — ............... 55
5-8. Schematic Diagram — Power Amp Section — .................. 59
5-9. Printed Wiring Board — Panel Section — ......................... 63
5-10. Schematic Diagram — Panel Section — ......................... 67
5-11. IC Block Diagrams ........................................................... 70
5-12. IC Pin Functions ............................................................... 75
6. EXPLODED VIEWS
6-1. Case Section........................................................................ 82
6-2. Front panel Section ............................................................. 83
6-3. OSD Board Section............................................................. 84
6-4. Chassis Section ................................................................... 85
7. ELECTRICAL PARTS LIST ........................................ 86
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
LESCOMPOSANTSIDENTIFIÉS PARUNEMARQUE!SUR
LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES
PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE
FONCTIONNEMENT.NE REMPLACER CES COMPOSANTS
QUE PAR DES PIÈCES SONY DONT LES NUMÉROS
SONT DONNÉS DANS CE MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.
SAFETY-RELATED COMPONENT WARNING !!
COMPONENTS IDENTIFIED BY MARK !OR DOTTED LINE
WITH MARK !ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
SAFETY CHECK-OUT
After correcting the original service problem, perform the follow-
ing safety checks before releasing the set to the customer:
Checkthe antenna terminals, metaltrim, “metallized” knobs, screws,
and all other exposed metal parts forAC leakage. Check leakage as
described below.
LEAKAGE
The AC leakage from any exposed metal part to earth Ground and
from all exposed metal parts to any exposed metal part having a
returnto chassis, must not exceed0.5 mA (500 microampers). Leak-
age current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of aVOM
or battery-operatedAC voltmeter. The “limit” indication is 0.75
V, so analog meters must have an accurate low-voltage scale.
The Simpson 250 and Sanwa SH-63Trd are examples of a pas-
sive VOM that is suitable. Nearly all battery operated digital
multimeters that have a 2V AC range are suitable. (See Fig. A)
Fig. A. Using an AC voltmeter to check AC leakage.
To Exposed Metal
Parts on Set
0.15
µ
F1.5k
Ω
AC
voltmeter
(0.75V)
Earth Ground
MODEL IDENTIFICATION
— BACK PANEL —
Parts No.
Parts No. Model
4-989-884-6
4-989-884-0
4-989-884-1
4-989-884-2
4-989-884-3
4-989-884-4
D760Z : US model
DE815G : US model
DE815G : Canadian model
DE815G : E, PX model
DE815G : Singapore, Malaysia model
DE815G : Australian model
w
w
w
.
x
i
a
o
y
u
1
6
3
.
c
o
m
Q
Q
3
7
6
3
1
5
1
5
0
9
9
2
8
9
4
2
9
8
T
E
L
1
3
9
4
2
2
9
6
5
1
3
9
9
2
8
9
4
2
9
8
0
5
1
5
1
3
6
7
3
Q
Q
TEL 13942296513 QQ 376315150 892498299
TEL 13942296513 QQ 376315150 892498299
http://www.xiaoyu163.com
http://www.xiaoyu163.com