Sony BRAVIA KDL-52XBR User manual

Printed in Japan © 2007 Sony Corporation
3-272-867-12(1)
KDL-52XBR
KDL-46XBR
KDL-40XBR
KDL-52X3100
KDL-46X3100
KDL-40X3100
3272867120
Installing the Wall-Mount Bracket
To Customers:
For product protection and safety reasons, Sony strongly recommends that installing of
your TV be performed by Sony dealers or licensed contractors. Do not attempt to install
it yourself.
Your KDL-52XBR/KDL-46XBR/KDL-40XBR/KDL-52X3100/KDL-46X3100/KDL-
40X3100 can be installed using SU-WL500 Wall-Mount Bracket (sold separately). Please
provide your licensed contractor with this installation supplement as well as the
Instructions (supplied with the SU-WL500 Wall-Mount Bracket). Read these documents
carefully for safety and proper installation.
To Sony Dealers and Contractors:
Provide full attention to safety during the installation, periodic maintenance and
examination of this product.

Installing the TV
The TV can be installed on a wall by attaching a Wall-
Mount Bracket (sold separately).
Verify your TV’s model number and be sure to use the
bracket specified for your model only. Refer to the
Steps on this manual along with the Instructions
supplied with the SU-WL500 Wall-Mount Bracket, to
properly carry out the installation.
Open the Wall-Mount Bracket package and check the
contents for all required parts along with the
Instructions.
Decide where you want to install your TV. Refer to
“TV installation dimensions table” in this manual for
the TV installation dimensions table.
Refer to the Instructions for SU-WL500.
Refer to the Instructions for SU-WL500.
Before detaching the Table-Top Stand, disconnect all
the cables from the TV. Refer to Operating Instructions
supplied with the TV set for detaching the Table-Top
Stand.
Referring to “Screw and Hook locations diagram/
table” in this manual, determine the screw positions,
and secure the Mounting Hook to the rear of the TV.
When changing the bezel unit to the optional one,
replace it before removing the Table-Top Stand. The
bezel unit cannot be replaced after installing on a wall.
(KDL-52X3100/KDL-46X3100/KDL-40X3100 only)
Refer to the Instructions for SU-WL500.
Sufficient expertise is required for installing this
product, especially to determine the strength of the
wall for withstanding the TV’s weight. Be sure to
entrust the attachment of this product to the wall to
Sony dealers or licensed contractors and pay
adequate attention to safety during the installation.
Sony is not liable for any damage or injury caused
by mishandling or improper installation.
Step 1: Checking the parts
required for the
installation
Step 2: Deciding on the
installation location
Step 3: Installing the Base
Bracket on the wall
Step 4: Preparing for the
installation of the TV
Step 5: Installing the TV on
the wall
Unit: mm
Figures in the above table may differ slightly depending on the installation.
The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV. Refer to the
Operating Instructions supplied with the TV set for its weight.
* Hook position “c” cannot be used for the models in the table above.
TV installation dimensions table
Model Name Display dimensions Screen centre dimension Length for each mounting angle Angle (0°) Angle (20°)
AB C DEFGH
KDL-52XBR 1,415 827 73 491 185 415 781 533
KDL-52X3100 1,415 827 73 491 183 415 781 533
KDL-46XBR 1,262 734 128 500 183 378 694 542
KDL-46X3100 1,262 734 128 500 181 378 694 542
KDL-40XBR 1,111 657 176 509 183 349 621 550
KDL-40X3100 1,111 657 176 509 181 349 621 550
Screw and Hook locations diagram/table
Model Name Screw location Hook location
KDL-52XBR/KDL-52X3100 d, g a
KDL-46XBR/KDL-46X3100/KDL-40XBR/KDL-40X3100 e, g b
320
Screen centre point
WARNING
Screw location Hook location
b
a
c*