Sony DVCAM DSR-60 User manual

SONY.
[DVCAM |],
DIGITAL
VIDEOCASSETTE
PLAYER
DSR-60
DSR-60P
INSTALLATION
MANUAL
1st
Edition

SAFETY CHECK-OUT
After correcting the original service problem, perform the
following safety checks before releasing the set to the
customer :
Check the metal trim, “metallized” knobs, screws, and all
other exposed metal parts for AC leakage. Check leakage
as described below.
LEAKAGE TEST
The AC leakage from any exposed metal part to earth
ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5
mA (500 microampers). Leakage current can be measured
by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229
or RCA WT-540A. Follow the manufacturers’
instructions to use these instruments.
2. A battery-operated AC milliammeter. The Data
Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means
of a VOM or battery-operated AC voltmeter. The
“limit” indication is 0.75 V, so analog meters must
have an accurate low-voltage scale. The Simpson 250
and Sanwa SH-63Trd are examples of a passive VOM
that is suitable. Nearly all battery operated digital
multimeters that have a2 V AC range are suitable. (See
Fig. A)
To Exposed Metal
Parts on Set
AC
0.15 pF 1.5kQ voltmeter
(0.75 V)
= Earth Ground
Fig A. Using an AC voltmeter to check AC leakage.
The material contained in this manual consists of
information that is the property of Sony Corporation and
is intended solely for use by the purchasers of the
equipment described in this manual.
Sony Corporation expressly prohibits the duplication of
any portion of this manual or the use thereof for any
purpose other than the operation or maintenance of the
equipment described in this manual without the express
written permission of Sony Corporation.
Le matériel contenu dans ce manuel consiste en
informations qui sont la propriété de Sony Corporation
et sont destinées exciusivement a l'usage des
acquéreurs de I'équipement décrit dans ce manuel.
Sony Corporation interdit formellement la copie de
quelque partie que ce soit de ce manuel ou son emploi
pour tout autre but que des opérations ou entretiens
de l'équipement a moins d'une permission écrite de
Sony Corporation.
Das in dieser Anleitung enthaltene Material besteht aus
Informationen, die Eigentum der Sony Corporation sind,
und ausschlieBlich zum Gebrauch durch den Kaufer der
in dieser Anleitung beschriebenen Ausriistung bestimmt
sind.
Die Sony Corporation untersagt ausdriicklich die Ver-
vielfaltigung jeglicher Teile dieser Anleitung oder den
Gebrauch derselben flr irgendeinen anderen Zweck als
die Bedienung oder Wartung der in dieser Anleitung
beschriebenen Ausrustung ohne ausdrtckliche schriftli-
che Erlaubnis der Sony Corporation.

introducing
this
manual
Related manuals
This
manual
is
the
installation
manual
of
the
digital
videocassette
player
model
DSR-60/60P.
This
manual
contains
rack
mount
information
necessary
for
installation
of
the
equipment,
the
connector
information
necessary
for
connecting
the
unit
with
peripherals
and
others.
In
addition
to
this
Installation
Manual,
the
following
manuals
are
provided.
+
Operating
Instructions
(Supplied
with
equipment)
Parts
number
:
3-859-820-11
(English,
for
UC,
CE)
3-859-820-21
(French,
for
UC,
CE)
3-859-820-31
(German,
for
CE)
3-859-820-41
(Italian,
for
CE)
Explains
how
to
operate
this
equipment.
*
Service
Manual
vol.
1
(Not
supplied
with
equipment)
Parts
number
:
9-977-696-11
Contains
the
maintenance
information
and
servicing
information
necessary
for
parts
replacement
and
adjustment.
©
Service
Manual
vol.
2
(Not
supplied
with
equipment)
Parts
number
:
9-977-696-21
Contains
the
block
diagrams,
board
layouts,
schematic
diagrams
and
parts
lists.

INSTALLATION
1,
Installation
Procedure
........ccccceeeeeesseeeerereeeeeeererenseneeesesees
1
2.
Operational
Environment
...........-sssccseessseseseeeeeseseneeneesersees
i
3.
Operating
Voltage
.......eccessessessssessecseeseeseseetenesnnetnteeecenees
1
4.
Installation
Space
0.
cccsseseseesetsseeetenesesesneeeressesnenssstsreeees
2
5.
Supplied
Accessories
........esessscesereesseseseeesecneentenseeersrsesees
2
6.
Optional
ACCeSSsOries
.........ssecsessesesseeseseesesnnenieeeneatenteenes
2
JT.
Rack
Mounting...
ccecescssesseseeseeesenenseenecesaseeeereeeessneseeseeeaees
3
8.
Connection
of
Editing
Equipment,
and
Input/Output
Signals
Of
CONMNECEOLS
.o..ccceccceseessscceeceseseseceeeescescesaecaeeeneretaeereesseseees
5
8-1.
Connection
of
Editing
Equipment...
creer
5
8-2.
Matching
Commectors
.......ccccesecesesesseesreecsessseesseenens
8
8-3.
Input/Output
Signals
of
the
Connectors
..
9.
Installation
Setup
and
Adjustment
...................
9-1.
Switch
Settings
on
the
Connector
Panel
................-+
9-2.
Setting
on
the
Front
Panel
UMit
«2.0...
seesssessesseeeens
11
9-3,
On-board
Switch
Setting
..........ccsseeeeeseeeetereeretees
12
9-4,
System
Adjustment
After
Installation
...........-:+000
14
9-5.
Connection
of
Editor
Controller
...........:
scree:
14
10. Setup Check Sheet
TABLE OF CONTENTS

Be
sure
to
install
the
DSR-60/60P
in
location
satisfying
the
required
operational
environment
described
below
to
assure
INSTALLATION
the
DSR-60/60P
superior
performance
and
to
maintain
the
excellent
serviceability
and
accessibility.
14.
INSTALLATION
PROCEDURE
[ START
1
DETERMINATION OF
INSTALLATION PLACE
1
[UNPACKING
y si
-
2.
OPERATIONAL
ENVIRONMENT
-
3,
OPERATING
VOLTAGE
-
4,
INSTALLATION
SPACE
. 5, SUPPLIED ACCESSORIES
RACK
MOUNTING
»
+
»
7,RACK
MOUNTING
CONNECTORS
.
«+
8-2.
MATCHING
CONNECTORS
OPERATION CHECK
.
8-3.
INPUT/OUTPUT
SIGNALS
OF
THE
CONNECTORS
.
9,
INSTALLATION
SETUP
AND
ADJUSTMENT
.
If
an
error
message
is
shown
on
the
time
counter,
refer
to
“3.3.
ERROR
MESSAGE”
in
SERVICE
MANUAL
VOL.
1.
2.
OPERATIONAL
ENVIRONMENT
+
Operating
temperature
:
+5
°C
to
+40
°C
+
Humidity
:
80
%
or
less
+
Storage
temperature
:
—20°C
to
+60
°C
+
Locations
to
avoid
-
«
Areas
where
the
unit
will
be
exposed
to
direct
sunlight
or
any
other
strong
lights.
Dusty
areas
or
areas
where
it
is
subject
to
vibration.
Areas
with
strong
electric
or
magnetic
fields.
Areas near heat sources.
(Good
air
circulation
is
essential
to
prevent
internal
heat
build-up.
Place
the
unit
in
location
with
sufficient
air
circulation.
Do
not
block
the
ventilation
holes
on
the
cabinet
and the rear panel.)
*
Horizonal
condition
:
within
+30
°
3.
OPERATING
VOLTAGE
¢
Power
voltage
:
AC
100
V
to
120
V/NTSC
AC
200
V
to
240
V/PAL
*
Power
frequency
:
50/60
Hz
¢
Power
consumption
:
NTSC
(UC):
85
W
PAL
(CE)
:87W
;
3
:
;

4. INSTALLATION SPACE
(1) The rear side must be at least 40 cm away from the walls for ventilation and maintenance.
(2) When the unit is operated on a desk or similar condition, assure that the clearance above the unit is at least 40 cm to provide accessibility
to the printed circuit boards and other mechanical parts. Note that it is not necessary to provide the space when the unit is mounted in a
rack since the printed circuit boards can be repaired after it is pulled out.
5
=| =
2) +
i
° Att :
L_] LJ
.
372
i
27.5
L
400
44
427 494
512
Set’s height at
rack
mounting.
30
(handle
hight)
F
577
(maximum
traveling
distance)
Pi gr EE ae ee ee PE Nr Na SOIR IT Mae a a SRR CERO Ec eae Gi
fr
ht
when rack-mounted
(height as slide rail center) Unit : mm
5. SUPPLIED ACCESSORIES
¢ AC power cord : (1)
RCC-SG 9-pin remote cable : (1)
* Operating instructions : (1)
* ClipLink™ Guide : (1)
6. OPTIONAL ACCESSORIES
© TBC remote control unit : UVR-60/60P
* Rack mount Kit > RMM-130
(The unit can be mounted in a 19-inch standard rack)
* Remote control cable : RCC-5G/10G/30G
¢ Cleaning cassette tape : PDVM-12CL
* Circus Remote control : SVRM-100A
* Digital video cassette (Mini size) : PDVM-12ME/22ME/32ME/40ME
* Digital video cassette (Standard size) : PDV-64ME/94ME/124ME/184ME
¢ SDI output board : DSBK-100/100P
© QSDI output board : DSBK-110/110P
© Time code input/output board : DSBK-130/130P

7. RACK MOUNTING
The
unit
can
be
mounted
in
a
19-inch
standard
rack.
1.
Remove
the
four
screws
on
right
and
left
side
panels.
It is
recommended
to
use
the
following
kit.
And
install
the
Inner
Members
of
the
rails
to
the
right
and
left
side panels with the screws removed.
Rack
Mount
Kit
:
RMM-130
(optional
accessory)
—]
or
Screws
(B
4x6)
_
Inner
memeber
|
RACK-MOUNT
SLIDES
:
MODEL
305
:
slide
length
22
inch
(ACCURIDE)
Note for rack mounting :
¢
When
several
VTRs
are
mounted
in
a
rack,
it
is
recommended
to
install
a
fan
for
ventilation.
Good
air
circulation
is
essential
to
prevent
internal
heat
build-up
in
a
rack
(+5
°C
to
+40
°C
must
be
met for all units).
Never
remove
an
upper
panel
and
lower
panel
during
rack
mounting.
Be
sure
to
secure
the
rack
to
the
floor
to
avoid
accidents
when
a
8g
Screws
(B
4x6)
|
unit
is
pulled
out.
Inner member
|
Connect
long
enough
cables
on
the
connector
panel,
considering
that
the
unit
is
pulled
out.
2.
Install
the
Outer
Member
Brackets
of
the
slide
rails
to
the
rack.
*
This
equipment
can
use
with
two
tiers.
Adjust
the
distance
from
the
edge
of
the
slide
rail
to
the
outside
But
with
three
tiers
and
more,
keep
the
spaces
between
the
each
of
the
rack
so
that
it
meets
the
required
specification.
VTRs
in
the
rack
1
unit
(about
44
mm)
or
more.
L-angle Outer member
Rack

3. Remove the two screws (B 4x8) on the right and left side
panels. (Be careful not to lose these four screws.)
Screws (B 4x8)
Screws (B 4x8)
4. Install the L-angles to the holes described in step 3 with the
supplied screws (PSW 4x16) in RMM-130 for these L-angles.
Screws (PSW 4x16)
Screws
(PSW 4x16)
Note: Never use screws PSW 4x16 to install the right and left
side panels without L-angles. Be sure to install the panels
with the screws B 4x8 removed in step 3. Screws for L-
angles are longer than the side panels. Therefore, using the
screws PSW 4x16 may cause trouble in the unit.

8.
CONNECTION
OF
EDITING
EQUIPMENT,
AND
INPUT/OUTPUT
SIGNALS
OF
CONNECTORS
8-1.
Connection
of
Editing
Equipment
Connection
for
Digital
Non-Linear
Editing
System
The
digital
non-linear
editing
system
can
be
configured
by
connecting
DSR-60/60P
with
the
edit
station
ES-7.
Use
of
the
optional
QSDI
interface
enables
transfer
of
the
compressed
data
such
as
video,
audio
and
timecode
from
DSR-60/60P
to
ES-7.
DSR-60/60P
supports
the
ClipLink
function
The
index
picture
which
is
recorded
on
tape
and
the
ClipLink
log
data
which
is
stored
in
the
cassette
memory
can
be
transferred
immediately
to
ES-7.
*
Refer
to
“ClipLink™
Guide”
supplied
with
the
unit
for
general
description
of
ClipLink
functions.
Connection
example
of
digital
non-linear
editing
system
when
DSR-60/60P
is
used
as
a
player,
is
shown
below.
+
Refer
to
the
Operating
Instructions
supplied
with
ES-7
for
the
connection
procedure
of
the
peripheral
equipment
(such
as
contro]
panel
ESBK-7011,
disk
unit
ESBK-7045,
etc.,)
of
ES-7.
=
|
QSDI OUT
REF. VIDEO IN
B B OUT (1/2/3/4)
QSDI IN
REMOTE @
“J
Edit station ES-7
®
Composite video input
@
75
Q
co-axial
cable
(optional)
{2
-—————
@
9-pin
remote
cable
(5
meter
jong,
supplied)
me
@
RCA
plug
(optional)
q
Lp
m—
mo gg ooogg
4 66 g900000
Video monitor
DSR-60 setting
Switch
REMOTE/LOCAL
REF.
VIDEO
IN
terminated
in
75
Q
ON
j
H
q
4
}
i
i
3
H

Connection for Cut Editing System
Connection example of the cut editing system when DSR-60/60P is connected with DSR-85/85P is shown below.
* Refer to the Operating Instructions of other equipment at the same time for connection.
When ASSEMBLE edit or INSERT edit is selected
at the editor, the EDIT MODE indicator on the
front panel of DSR-85/85P (recorder) lights,
entering the editing mode automatically.
@ 75 Q co-axial cable (optional)
fe+———
@ 9-pin remote cable (5 meter long, supplied) | >———
@ RCA plug (optional) qf fC }rm———
®
DSR-60/60P DSR-85/85P
(player) QSDI OUT QSDIIN_ (recorder)
wy fo; (© © © REF. VIDEO @ © 10 [O| @|@ ©|@
\ @] \) @|
WFD | UN sad © 6000 (C900 ZS
| WF 39, e0e@ WF
LO000 @) ieqoood
lo (eae) 1e Sr eae KG)
MONITOR ViDEO REMOTE MONITOR VIDEO REMOTE
AUDIO OUT 2 AUDIO OUT 2
(SUPER) (SUPER)
® ® ® ® ® @
Audio input Composite video input Audio input Composite video input
PLAYER REF. VIDEO IN
2 88 sooo0009
sony | 3 68.06.88:68 86:00:86.08 00 68:08.98.68
a 88 _ogoog
75 66 09009009
Source monitor =
ooco
@ ooo fj OO COoo OO
oooo = Main monitor
ooooo ‘e
co
oIMjoc3 RECORDER
Editing control unit
RM-450/PVE-500 (editing side)
Switch setting of DSR-60/60P (player) and DSR-85/85P (recorder)
Switch
Recorder
REMOTE/LOCAL
« Refer to the Operating Instructions of DSR-85/85P for video/audio input of recorder and for audio mode setting.
Note : When the QSDI interface is used for the connection, monitor of the JOG audio cannot be switched to the recorder
monitor even through recorder enters the E-E mode. Therefore, monitor the JOG audio at the player side.
About the reference video signal
The reference video signal which is synchronized with the video signal in use, is necessary and must be input to the REF. VIDEO IN
connector for analog signal editing in order that the built-in TBC works correctly and the stable picture and audio are obtained.
6