Sorelle Princeton Elite User manual

Made in QHY, China
Important Information:
Assembly Instruction
Read all instructions
By Sorelle - A Division of C & T International, Inc.
46 Whelan Road, East Rutherford, N.J.07073 U.S.A.
Tel, [phone] Fax, [phone]
BEFORE assembling crib.
KEEP INSTRUTIONS FOR FUTURE USE.
Princeton Elite Crib and Changer
Website: www.sorellefurniture.com

Page 2
Sorelle
WARNING:
*Infants can suffocate on soft bedding. Never add a pillow or comforter. Never place additional padding
under an infant.
*Failure to follow these warnings and the assembly instructions could result in serious injury or death.
DO NOT use this crib if you cannot exactly follow the accompanying instructions.
*To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their backs to
sleep, unless otherwise advised by your physician.
*Strangulation Hazard: STRINGS CAN CAUSE STRANGULATION! Do not place items with a string
around a child's neck, such as hood strings or pacifier cords. Do not suspend strings over a crib or
attach strings to toys.
*Strangulation Hazard: To help prevent strangulation tighten all fasteners. A child can trap parts of
the body or clothing on loose fasteners.
*Strangulation Hazard: Do not place crib near window or patio door where cords from blinds or
drapes may strangle a child.
*Fall Hazard: When child is able to pull to a standing position, set mattress to lowest position and
remove bumper pads, large toys and other objects that could serve as steps for climbing out. This crib
has an adjustable mattress support. For the convenience of the parent when the baby is very small, the
mattress support may be used in the highest position. Important: with the mattress support and
mattress in the highest position, be absolutely sure that the top of the front crib side is at least 3 inches
higher then the top surface of the mattress. If it is not, lower the mattress support and the mattress to
the next highest position.
*Fall Hazard: Stop using crib when child begins to climb out or reaches a height of 35in. (89cm),
whichever occurs first. The child should be placed in a youth or regular bed.
*Check this product for damaged hardware, loose joints, loose bolts or other fasteners, missing parts,
or sharp edges before and after assembly and frequently during use. Securely tighten loose bolts and
other fasteners. Do not use crib if any parts are missing, damaged or broken. Contact C&T
International Inc. for replacement parts and instructional literature if needed. Do not substitute parts.
*Follow warnings on all products in a crib.
*If refinishing, use a non-toxic finish specified for children's products.
*Never use plastic shipping bags or other plastic film as mattress covers because they can cause
suffocation.
*Infants can suffocate in gaps between crib sides and a mattress that is too small.
*Ensure a safe environment for the child by checking regularly, before placing the child in the crib, that
every component is properly and securely in place.
*To avoid head injury, do not allow any child to play underneath the crib.
*Never add an accessory such as a bassinet or changing table that extends over the sleeping area.
C
Crib Warnings:
AUTION : ANYMATTRESSUSEDINTHISCRIBMUST
BEAT LEAST 271/4”(69CM)x 515/8”(131 CM) WITH
ATHICKNESSNOT EXCEEDING 6”(15CM).

Page 3
Sorelle
Toddler Bed Warnings:
Changing Table Warnings:
WARNING
INFANTS HAVE DIED IN TODDLER BEDS FROM ENTRAPMENT.
Openings in and between bed parts can entrap head and neck of a small child.
NEVER use bed with children younger than 15 months.
ALWAYS follow assembly instructions.
The maximum user weight is 50lbs (22.7kg)
WARNING
STRANGULATION HAZARD
NEVER place bed near windows where cords from blinds or drapes may strangle a child.
NEVER suspend strings over a bed.
NEVER place items with a string, cord, or ribbon, such as hood strings or pacifier cords,
around a child's neck. These items may catch on bed parts.
CAUTION
ENTRAPMENT HAZARD
To avoid dangerous gaps, any mattress used in this bed shall be a full-size crib mattress
at least 51 5/8 in (1310mm) in length, 27 1/4 in (690mm) in width and 4 in (100mm) in
thickness. The mattress thickness must not exceed 6 in (150mm).
WARNING
FALL HAZARD - to prevent death or serious injury, always keep child within arm’s reach.
Read all instructions before use of the changing table.
KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE USE.
Inspect the changing table periodically. Do not use the changing table if it is damaged or
broken. Contact C&T International Inc. with any questions.
Tighten all loose screws and bolts before each use.
The maximum recommended weight of the child is 30lbs for the changing table.
Use only the pad provided by C&T International Inc. or Manufacturer’s
Always secure the pad to the changing surface by inserting the strap through the hole in
the middle of the pad. See Instructions.
NEVER use crib without Changing Table attached

Page 4
Sorelle
C
AU
BEA
A THI
NOTES ON ASSEMBLY:
-During the assembly process whenever using screws or bolts, check each by placing the screw/bolt on
the diagram of the item which is drawn actual size and design. Be sure to use the proper size and shape
specified in the instructions.
-To assemble this unit you may be required to place the unit on it’s side and face. It is strongly
recommended that assembly is done on a soft, non-abrasive surface to avoid damaging the finish.
NOTES ON CARE AND MAINTENANCE:
- Do not scratch or chip the finish.
- Inspect the product periodically, contact C&T International Inc. for replacement parts or questions.
- Do not store the product or any parts in extreme temperatures and conditions such as a hot attic or a
damp, cold basement. These extremes can cause a loss of structural integrity.
-To preserve the luster of the high quality finish on your product, it is recommended to place a doily or
felt pad under any items you place on the finish.
-Clean with a damp cloth, then a dry cloth to preserve the original luster and beauty of this fine finish.
-Do not use abrasive chemicals.
-Do not spray cleaners directly onto furniture.
-Lift slightly when moving on carpeting to prevent leg breakage.
-Use of a vaporizer near furniture will cause wood to swell and finish to peel.
NOTES ON USE:
Keep children and others safe by following these simple rules:
- Do not allow any child to play on furniture
- Do not allow climbing on any piece of furniture.
- Do not allow hanging from any piece of furniture.
- Always monitor your child’s activity when in the nursery.

Page 5
Sorelle
ATH
Crib Assembly Parts
(A): Left Side Frame (x1) (A1): Left -Front Post (x1) (A2): Left -Back Post (x1) (B) Back Side Frame (x1)
(C) Front Side Frame (x1) (D) Front&Back Contoured Top (x2)
(H) Midlle Panel (x1) (I) Right End (x1) (K) Middle Panel (x1)
(L) Adjustable Shelf (x2)
(J) Top Shelf (x1)
(N) Changer Pad (x1)
(M) Bottom Shelf (x1)
PARTS LIST FOR CHANGER/DRESSER ASSEMBLY
(F) Metal Mattress Support (x1)
(O4) Support Bar For Contoured Top
(O1) Back Decorative Panel (x 1) (O3) Small Front
Contoured Top (x1)
(O2) Back Support Bar
Bolt Ends (x1)

(O7) Front - Bottom Bar (x1)
(HD) M6 x 17mm Allen bolt (x4)
(HB) M6 x 75mm Allen bolt (x1)
(HC) M6 x 65mm Allen bolt (x1)
(HE) M6 x 45mm Allen bolt (x26)
Page 6
Sorelle
Crib Assembly Parts
PARTS LIST FOR CHANGER/DRESSER ASSEMBLY
HARDWARE LIST
Tool required
(HN) Allen Wrench
(HI) Wood Dowel (x15) (HL) Special Bolt (x1)
(HH) Shelf Support
Brackets (x8)
(HF): 22mm Screws for knobs (x3) (HG): 25mm Phillips Screws (x24)
(O6) Front - Middle Bar (x1)
PARTS LIST FOR DRAWER ASSEMBLY
(P): Drawer Front (x3) (Q) Knob (x3)
(T) Drawer Back (x3)
(R) Drawer Right (x3) (S) Drawer Left (x3)
(U): Drawer Bottom Shelf (x3)
(O5) Front - Middle Bar
with Bolt Ends(x1)
(O8) Middle - Bottom Bar (x1)
(HA) M6 x 85mm Allen bolt (x2 )

Page 7
Sorelle
Step 1
Crib Assembly Steps
DRAWER ASSEMBLY
T
P
Q
HF
HG
HG
S
R
Grooves U
HG
HG
1. Working on a padded, flat surface, attach
drawer sides(R&S) to Drawer Back (T) with
four Philips Head Screw (HG), see Fig 1.
Tighten Screw (HG) half way only to leave
room for adusting when fitting drawer panel.
Fig. 1 Fig. 2
Fig. 3
Fig. 4
2. Slide Drawer Bottom(U) into drawer
assembly, see Fig 2.
Make sure Panel is inserted all the way
to the back tighten screws all the way.
3. Secure both side of drawer front(P)
to Drawer assembly with four(4) Philips
Head Screw (HG), see Fig 3.
4. Using Drawer Knob Screw(HF), install
one Knob(Q) on Drawer, see Fig 4.
Check All screws for tightness.
Parts Needed: refer to page 6, “Parts List For DRAWER ASSEMBLY”.
Phillips screw driver needed for fightening (HG) screws

O1
O2
O2
O8
O8
O1
O4
O3
O4
O5
O6
O7
O8
HE
HE
HE
HE
Page 8
Sorelle
Step 2
CHANGER/DRESSER ASSEMBLY
Parts Needed: refer to “PARTS LIST FOR CHANGER/DRESSER ASSEMBLY”
1.
3. Slide (M) into grooves of O2 and O8
Slide (J) into grooves of O4 and lower
grooves of O1. See Fig. 7
Fig. 7
4. Put the Right Ends on ground, then Insert Middle Panel
(K) into
Right End (I),See Fig. 8
Fig. 8
2.
Fig. 5
Fig. 6
J
M
K
Insert Contoured top(O3)&Support Bar O4;O5;O6;O7 and O8
into Right End (I) using 4 Bolts (HE)
See Fig 6.
Slide 1
Wood
Dowel(HI) into each end of Part (O7)
2and
Wood
Dowel(HI) into each end of Part (O8). then
Slide 1 Wood Dowel(HI) into each end of Parts
(O1&O2), Then attach Decorative Support Bar(O1)
and Back Support Bar (O2) to Right End (I) using
3 Bolts(HE).
See Fig.5
I
I
I

Page 9
Sorelle
Step 3
CHANGER/DRESSER ASSEMBLY
H
6. Attach Middle Panel(H) with each support bar See Fig 9.
and secure with 6 Bolts (HE).
Fig. 9
Fig. 11
Fig. 10
7. Insert Shelf Support Brackets (HH)
into holes in back of dresser, See Fig10.
8. Insert Shelf(L) into Support brackets. see Fig11
L
Parts Needed: refer to “PARTS LIST FOR CHANGER/DRESSER ASSEMBLY”
HE
HH

A
Page 10
Sorelle
Step 4
CRIB ASSEMBLY
C
C
Fig. 12
&
B
D
D
B
HI
HI
HE
HA
HB
HC
HA
HE
HE
HL
Fig. 13
Fig. 14
Fig. 14a
1.
Slide 1
Wood
Dowel(HI) into each end of
Front & Back Frame (B&C). See Fig.12
2. Put Back Contoured Top(D) to Side
Frame (B&C)
Side Frame (B&C)
and then
Attach to change table secure to top and
bottom with 4 Bolts(HE) and a Special Bolt (HL).See Fig.13
3.
Then attach the Left Side Fram
Attach the Post (A1&A2) to Left Side Frame(A) as Fig.14.
e (A) wtih Posts to Crib using 8 Bolts(HE) as Fig.14a
(A)
(A1)
(A2)

Page 11
Sorelle
Step 5
MATTRESS SUPPORT ASSEMBLY
Changing Pad Assembly
3. Make sure that safety belt is fastened around
child, and adjusted so safety belt is snug around
child’s mid-section. Make sure buckle is securely
latched. Figure 3.
CLICK!
1
2
3
2. Pull through front of pad completely. Make
sure pad is facing up and warnings are always
visible. Figure 2.
Important : If changing pad and safety belt are
assembled, make sure warnings are facing up and visible.
If not, reassemble by following the steps below.
1. Locate safety belt bolted to dresser top. Insert
safety belt through slit in changing pad from
back of pad. Figure 1.
F
Add changing pad (N) to top of organizer.
Important : Tighten all bolts before use your Crib.
Insert three (3) drawers into changer.
HD
HD

Page 12
Disassembling Crib For Storage
To disassemble crib for storage, follow assembly steps in reverse.
Store all parts and hardware together in a safe place. Store the instruction manual in the supplied
envelope attached to the mattress support assembly for future reference for re-assembly.
SORELLE
Converting to a Toddler Bed (Optional)
Follow all instructions supplied with the 129/151# Toddler Rail System. NOTE:
129/151#Toddler Rail
System is not included. Please see your crib retailer,
visit WWW.Sorellefurniture.com or contact C&T
International / Sorelle for more information.
Additional Parts and Hardwares
( 129/151# Toddler Rail System Not included, sold separately)
3x
C
B
E
D
4x
4x
1x
A
A1
Parts List
No Qty Description
A
B
C
D
Toddler rail
Bolt 42mm
Bolt 65mm
Barrel Nuts
1
A1 Support bar of Toddler rail1
3
4
4
EAllen key 1

Page 13
SORELLE
Follow all instructions supplied with the 228# Adult Rail System. NOTE: 228# Adult Rail System
is not included. Please see your crib retailer, visit WWW.Sorellefurniture.com or contact C&T
International / Sorelle for more information.
(S) Cross Slat x4
Fullsize Bed Conversion (Optional)
Additional Parts and Hardwares
( 228# Adult Rail System Not included, sold separately)
(R) Bed Rails (x2)
( V ) Additional Left - Rear Post
For Changer table alone (x1)
(W) Additional Right Post
For Footboard (x1)
d. Screw x16
Nuts x4g.
c. Flat Washer x 8
f. M6 x 75mm Allen bolt x4
e. M6 x 17mm Allen bolt (x4)