Better Homes and Gardens Maddox BH19-D1-1011-06 User manual

THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION.
PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Date 2019-01-24 Rev. 0001-A
Maddox Crossing Painted Chairs
Stock # BH19-D1-1011-06 White
# BH19-D1-1011-07 Black
ADULT ASSEMBLY REQUIRED
If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the
store where it was purchased. Please call our customer service number and have your instructions
and parts list ready to provide the model name, part name or factory number:
866-942-5362
Pacific Standard Time: 8:30 a.m. - 4:30 p.m., Monday - Friday
Or visit our web site 24 hours a day, 7 days a week for product assistance at
www.whalenstyle.com
Or e-mail your request to [e-mail]
LOT NUMBER:
DATE PURCHASED: / /

2
1. Maximum load weight 136 kg (300 pounds).
1. Please read the Assembly Instructions prior to assembling the unit.
2. To avoid damage, assemble the unit on a sturdy, level and non-abrasive surface.
3. Keep all hardware and parts out of the reach of children.
4. Please wait until all steps are completed before fully tightening bolts.
5. Make sure all nuts, bolts and screws are tightly fastened before the unit is used.
6. Check that all bolts and screws are tight at least every 3 months or as needed.
7. Use the long end of the hex wrench to fasten bolts loosely and quickly.
8. Use the short end of the hex wrench for final tightening.
G E N E R A L I N F O R M A T I O N , T I P S A N D T R I C K S
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM
WEIGHTS INDICATED. USE WITH LOAD HEAVIER THAN THE MAXIMUM WEIGHTS
INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE INJURY.
①
②

3
Parts and Hardware List
Please read completely through the instructions and verify that all listed parts and hardware are present
before beginning assembly.
A- Chair Backrest (Qty. 2)
B- Seat (Qty. 2) C- Front Leg (Qty. 4)
(1) M8 x 40 mm Bolt (2) M8 x 80 mm Bolt
(Qty. 4+1 extra) (Qty. 8+1 extra)
(3) Lock Washer (4) Flat Washer (5) M8 Hex Nut
(Qty. 20+1 extra) (Qty. 20+1 extra) (Qty. 8+1 extra)
T-handle Wrench (Qty. 1) Open Wrench (Qty. 1) Touch-up Pen (Qty. 1)
(Not included for White Finish)
Tools required: Hex wrench and open wrench (provided).

4
Assembly Instructions
1. Unpack the unit and confirm that you have all the hardware and required parts.
2. Lay one Chair Backrest (A) on a smooth and protected surface with the threaded holes facing up.
3. Attach one Seat Frame (B) to the Chair Backrest (A) with the end dowel fully inserted. Make sure the
Seat Board will face up when the unit is turned upright. Insert the 80 mm Bolts (2) with Lock Washers (3)
and Flat Washers (4) through the drilled holes on the seat frame at rear corner blocks and loosely tighten
into the threaded inserts on the Backrest (A).
4. Secure the Seat Frame (B) to the Chair Backrest (A) by inserting two 40 mm Bolts (1) with the Washers
(3 and 4) through the drilled holes on the rear rail of the Seat Frame.
A
4
1
3
4
2
3
B
A
B
DO NOT fully tighten the bolts or nuts initially until all the bolts or nuts are
ready to assemble. To avoid causing damages to the thread, DO NOT over-tighten the nuts or bolts.
②
x 4
③
x 6
④ x 6
①
x
2

5
Assembly Instructions
5. Flip the previous assembly upside down on a support surface.
NOTE: Place a protective cover (like the bubble wrap packing material) over the carton or other support
surface to prevent from scratching.
6. Remove the plastic caps from the hanger bolts of Chair Front Legs (C). Attach 2 Front Legs (C) to the
front corner blocks of the Seat Frame (B) by inserting the pre-attached hanger bolts through the drilled
holes on corner blocks, and fit the Flat Washer (4), Lock Washer (3) and Hex Nut (5) onto each hanger
bolt. Tighten the hex nuts with the provided open wrench.
NOTE: DO NOT fully tighten all the nuts until the chair has been adjusted and all the legs are levelled so
that they do not wobble. Once adjusted then go back and tighten while making sure that the unit remains level.
7. Stand the assembled chair upright on a flat surface. Press down the Seat (B) to even all legs. Now,
tightly fasten all bolts and nuts with the provided hex wrench and open wrench.
8. Repeat the same process to assemble the other chair.
B
C
C
A
C
3
B
4
5
C
⑤
x
4
③
x
4
④ x 4