Sota Silver Pulser SP6 User manual

© 2012-2021 SOTA Instruments Inc. Page 1 of 14|www.sota.com
The Silver Pulser
Model SP6 Manual
CONTENTS
WELCOME TO SOTA..................................................................................................... 3
BEFORE USING ............................................................................................................... 3
LEARN MORE ................................................................................................................. 3
COMPLETE UNIT INCLUDES...................................................................................... 3
DO NOT USE.................................................................................................................... 4
MICROPULSING CAUTIONS ...................................................................................... 4
IONIC~COLLOIDAL SILVER CAUTIONS................................................................. 5
GENERAL CAUTION..................................................................................................... 5
SUMMARY OF LIGHTS ................................................................................................. 5
HOW TO USE THE MICROPULSING FUNCTION .................................................. 6
How Micropulsing Should Feel ............................................................................... 9
Sensitive Skin ............................................................................................................... 9
Typical Use ................................................................................................................ 10
HOW TO USE THE IONIC~COLLOIDAL SILVER FUNCTION ...........................10
How to Assemble ...................................................................................................... 10
How to Make Ionic~Colloidal Silver...................................................................... 11
Typical Use................................................................................................................. 12
ELECTRICAL SPECIFICATIONS .............................................................................. 13
Power Requirements................................................................................................. 13

© 2012-2021 SOTA Instruments Inc. Page 2 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
Optional Power Input............................................................................................... 13
Output Specications................................................................................................ 13
TROUBLESHOOTING.................................................................................................. 14
COUNTRIES THAT PARTICIPATE IN MANUFACTURING............................... 14
REPLACEMENT ACCESSORIES................................................................................ 14
WARRANTY................................................................................................................... 14
REPAIRS.......................................................................................................................... 14

© 2012-2021 SOTA Instruments Inc. Page 3 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
WELCOME TO SOTA
Thank you for allowing us to be a part of your Wellness Team.
The Silver Pulser is a consumer product designed to be used as part of a Wellness
Lifestyle. A commitment to healthy lifestyle choices is an important factor in the
journey to Wellness.
The SOTA Silver Pulser has two functions – Micropulsing and making Ionic~Colloidal
Silver. Micropulsing offers gentle microcurrents that work with the body’s natural
electricity for more energy, general health and well-being. Ionic~Colloidal Silver is one
of nature’s gifts and can be made easily and inexpensively at home.The Silver Pulser
is designed to be used independently, but can also be used together with any of the
SOTA Products.
With proper care, your Silver Pulser should provide you many years of trouble-free
use.
Please understand that results will vary.
BEFORE USING
Please read the manual thoroughly before using your Silver Pulser. For the most up-to-
date manual, please visit our website www.sota.com/manuals.
We’ve made every effort to ensure the information in your manual is up-to-date at
the time of printing ... since that time however, new information may have become
available.
LEARN MORE
To learn more about the Silver Pulser we invite
you to visit the SOTA website:
www.sota.com
The website offers How to Videos, Frequently
Asked Questions, The SOTA Products User
Guide, SOTA News ... and more.
COMPLETE UNIT INCLUDES
• One (1) Silver Pulser Unit
• One (1) 9-Volt Alkaline Battery
• One (1) Carrying Case

© 2012-2021 SOTA Instruments Inc. Page 4 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
• One (1) Product Manual
FOR MICROPULSING APPLICATION:
• One (1) Micropulsing Cord for Rubber Probes
• Two (2) Pair Conductive Rubber Probes
• Six (6) Pair Cotton Sleeves with Velcro®
• One (1) Arm Band with Clip
• One (1) Neoprene®Velcro®Wrist Strap
• One (1) Dark Glass Dropper Bottle
FOR MAKING IONIC~COLLOIDAL SILVER:
• One (1) Silver Wire Holder
• Two (2) Silver Wires of .9999 (4 Nine) Purity
• One (1) Green Scrub Pad
DO NOT USE
1.Do not use in the following situations as safety has not been explored using the
Micropulsing function:
a. In the case of pregnancy.
b. With an active implanted device such as a pacemaker, etc.
2.As with all electrical products do not use near water, when driving a car or when
operating heavy equipment.
3.Do not connect the Micropulsing Cord or the Silver Wire Holder to any other USB
outlet, such as a computer or power supply. Do not plug any other USB connections
into the Silver Pulser, other than the Micropulsing Cord and the Silver Wire Holder.
MICROPULSING CAUTIONS
1.Do not place the Conductive Rubber Probes over skin lesions, abrasions, new scars,
cuts, eruptions or sunburn.
2.Discontinue use if the Micropulsing suddenly feels different or prickly and the
YELLOW light stops ashing. Turn the unit OFF and contact SOTA.
3.Caution is advised if using potentially harmful substances such as recreational and
prescription drugs, as it is not known if microcurrents will interact or if individual
reactions may occur.

© 2012-2021 SOTA Instruments Inc. Page 5 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
4.Caution is required in the following situations as a burn may occur, which could
scar:
a. Do not apply the bare metal pins to the skin.
b. Do not allow the Cotton Sleeves to dry out while Micropulsing.
c. Do not Micropulse while sleeping, as the Cotton Sleeves may dry out.
IONIC~COLLOIDAL SILVER CAUTIONS
We recommend taking occasional breaks from consuming Ionic~Colloidal Silver for
the following reason:
A handful of people have experienced argyria after drinking large amounts of
Ionic~Colloidal Silver daily, over a long period of time. Argyria is a bluish tinge of
the skin. This occurs when excess silver is eliminated through the skin and exposed
to light. Darkening of the moons of the nger nails is usually an early sign.
The risk of argyria is considered greater for those who are ingesting incorrectly made
Ionic~Colloidal Silver and to a lesser degree, those who are decient in selenium or
vitamin E.
When making and drinking Ionic~Colloidal Silver as currently recommended by
SOTA, the risk of argyria is extremely rare.
GENERAL CAUTION
While this technology is generally considered safe, there exists potential for rare
individual reactions that cannot reasonably be foreseen. Therefore, your use of the
SOTA Products constitutes your agreement that you are responsible for your decision
to use the technology and that you hold SOTA harmless for any injuries or damage
believed to arise from using the SOTA Products.
SUMMARY OF LIGHTS
GREEN: Indicates the unit is on.
RED: Indicates the battery is low and will soon need replacing.
YELLOW: Indicates the Micropulsing function is in operation.
ORANGE: Indicates the Ionic~Colloidal Silver function is in operation.

© 2012-2021 SOTA Instruments Inc. Page 6 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
HOW TO USE THE MICROPULSING FUNCTION
1.Place the 9-Volt Alkaline battery in the unit.
a. On the back of the unit, slide off the
battery cover.
b. Position the 9-Volt Alkaline battery so
the positive (+) and negative (-) terminals
line up as in image 1.
Note: The smaller circle on the battery
matches the smaller circle in the case
… the larger battery circle matches the
larger circle in the case.
c. Slide the 9-Volt Alkaline battery into the case and push down. Slide the cover back
onto the unit.
2. Attach the Conductive Rubber Probes to the
Micropulsing Cord by gently sliding the Rubber
Probes over the metal pins on the Micropulsing Cord,
as in image 2.
Note: Except to occasionally clean them, the Rubber
Probes can stay on the Micropulsing Cord between
uses.
3. Clean the wrist area
to remove oils from the
skin. This will allow for better conductivity.
4.Insert the Micropulsing Cord into the jack on the unit
as shown in image 3. The USB symbol on the plug
should be facing up. When the plug is positioned
correctly, it will slide in gently. Do not force.
5.Slide the clip on the back of the Silver Pulser into the
holding clip on the Arm Band as in image 4 on page 7.
6.Slide the Arm Band, with the unit and cord, up the arm
to a comfortable position. Tighten the band to secure it
in place as in image 5 on page 7.
1
2
3

© 2012-2021 SOTA Instruments Inc. Page 7 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
Options:
a. If preferred the unit can be placed in a pocket.
A longer Micropulsing Cord is needed for this
option.
b. If the Arm Band is too large a shorter Arm Band is
available.
3.Put the Wrist Strap on with the Velcro®side of the
Wrist Strap face-out rather than towards the skin.
4.Prepare one pair of Cotton Sleeves. Each Cotton Sleeve is
sewn on three sides; to nd the open end of the Cotton
Sleeve, squeeze the long sides of the sleeve and the
unsewn end will pop open.
5.Attach one Cotton Sleeve to the Wrist Strap in line with
the pulse point on the thumb
side of the wrist. The open end
of the Cotton Sleeve will point
down toward the elbow. Press the
sleeve to the Wrist Strap to rmly
adhere the sleeve in place.
6. Place the other Cotton Sleeve, again with the open side
towards the elbow, in line with the pulse point on the little
nger side of the wrist. This pulse point is usually harder to
feel. It is located in the soft hollow on the wrist, in line with
the little nger. Press the sleeve to the Wrist Strap to rmly
adhere the sleeve in place. See image 6.
Once in place, the Velcro®will hold the Cotton Sleeves in the
right position for repeated use.
7.Take the Wrist Strap off.
8.Insert one probe from the Micropulsing Cord into the open end of each Cotton
Sleeve. Use a gentle twisting motion to work the Rubber Probes into the Cotton
Sleeves.
9.Wet the Cotton Sleeves with water.
10.Put the Wrist Strap on so the damp Cotton Sleeves are against the skin over the
4
6
5

© 2012-2021 SOTA Instruments Inc. Page 8 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
pulse points. See image 7 on page 8.
11.Turn the unit ON by rotating the ON/OFF switch
clockwise. Turn the switch slowly until you feel the
current. If you do not feel the current, see ‘Notes’ on page
8.
a. The green light indicates the unit is ON. If the light does
not come on, the battery may not be placed correctly.
b. The ashing yellow light should come on and get
brighter as the intensity is turned up. If the ashing
yellow light does not come on, the electrical path has not
been established. See ‘Troubleshooting’ on page 14.
16.When nished, turn the unit OFF by rotating the ON/OFF
switch counter clockwise until it clicks. Do not force the ON/OFF switch past its
natural stopping point.
17. Unplug the Micropulsing Cord. Do not
store the unit with the Micropulsing Cord
plugged in as this can damage the Cord.
18. The Cotton Sleeves will remain correctly
positioned for the next session.
19. Clean the wrist and apply a healing
lotion to avoid irritation.
Notes:
Suggestions for Feeling the Current: If the
current is not felt with wet Cotton Sleeves,
prepare a mild salt solution to wet the sleeves.
Add a few grains of salt to the water in the 50
ml dropper bottle.
Drink enough water to keep the body well
hydrated. Hydration can affect the ability to
feel the current.
Care of Micropulsing Cord and Rubber Probes: Remove the Rubber Probes
occasionally to clean in a mild soap solution. Rinse thoroughly. If necessary, gently
wipe the metal pins of the Micropulsing Cord.
7
8

© 2012-2021 SOTA Instruments Inc. Page 9 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
Care of Cotton Sleeves: Wash or rinse sleeves occasionally. Periodically discard and
replace Cotton Sleeves.
Alternatives to Cotton Sleeves:
a. Sponge Sleeves: available from SOTA.
b. All Cotton Sleeves: SOTA offers Cotton Sleeves without Velcro®.
c. Unbleached Paper Towel: Cut a small square of paper towel large enough to wrap
around the Rubber Probe 2 or 3 times.
d.Cotton Flannel: Cut a small square of cotton annel and wrap around the Rubber
Probe. Secure it in place with thread.
Rubber Probes: Over time, the Rubber Probes will lose their conductivity and need
replacing. Refer to the SP6 Troubleshooting Guide for instructions on how to test the
Rubber Probes.
Low Battery Warning: The RED light comes on when the battery is low. This means
the battery will soon need to be replaced. The battery can continue to be used until
the YELLOW light goes off.
Power Supply: When Micropulsing, as a safety feature, the unit can only be powered
by a 9-Volt battery.
Replacement Batteries: When purchasing replacement 9-Volt batteries, take the
Silver Pulser with you to ensure a proper t, as 9-Volt batteries vary in size.
HOW MICROPULSING SHOULD FEEL
1. The sensation is a gentle pulsing. While the microcurrents should be felt, it is not
necessary to turn the intensity control up to an uncomfortable level.
2. With repeated use, the ability to feel the microcurrents may change. It may be
necessary to increase the intensity in order to feel the microcurrents.
3. Twitching of the ngers is normal at a higher intensity.
4. During the rst weeks of use, the skin may become irritated. Over time, irritation
usually decreases or disappears. Alternate wrists each session to minimize the
potential for irritation.
SENSITIVE SKIN
Some individuals may be particularly sensitive to microcurrents and the irritation may
continue. To minimize irritation:

© 2012-2021 SOTA Instruments Inc. Page 10 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
1. Use Sponge Sleeves - available from SOTA.
2. Wash wrists thoroughly after each session and apply a healing gel or lotion such
as aloe vera, vitamin E or MSM cream.
3. Micropulse for shorter periods of time until the irritation disappears.
4. Wet the Cotton Sleeves with distilled water or Ionic~Colloidal Silver. If unable to
feel the current, try a commercial saline solution for the eyes. This is gentler than
adding salt to the water.
5. A conductive gel or aloe vera gel added to the wet sleeves may help to reduce
irritation.
TYPICAL USE
Alternate wrists daily.
Length of Session: Build up time gradually. It is best to start slowly. Start with 10 to
20 minutes a day. Increase gradually to a minimum of 2 hours each day.
Length of Use: The SOTA Products User Guide available at
www.sota.com/spug offers suggestions for Focused, Basic and Ongoing Wellness
Plans.
General Guideline: Use daily for a minimum of 8 to 12 weeks. Once completed,
setting a schedule for ongoing use is benecial.
Drink Plenty of Water: It’s important to drink enough water when using the unit.
Drinking ozonated water is especially helpful.
Stop Gradually: Reduce the amount of time each day for the last week of use. If
using more than one SOTA unit, it is suggested to stop only one unit at a time.
HOW TO USE THE IONIC~COLLOIDAL SILVER FUNCTION
HOW TO ASSEMBLE
1.The Silver Wires t into the two small holes in the Silver
Wire Holder as in the picture.
2.To insert the Silver Wires, move the spring clip away from
the hole.
3.Push the wire through the hole. Most of the wire should
be below the holder. Release the spring clip to hold the

© 2012-2021 SOTA Instruments Inc. Page 11 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
Silver Wire snuggly in place. It may be easier to insert from the underside of the
holder.
4.Repeat Step 2 for the second Silver Wire.
5.Plug the Silver Wire Holder into the Silver Pulser, ensuring that the USB symbol on
the plug is facing up.
HOW TO MAKE IONIC~COLLOIDAL SILVER
The Silver Pulser provides a constant current output, which allows for a very simple
procedure for making a high quality Ionic~Colloidal Silver using room temperature
water.
1.Pour two cups (16 ounces or 500 ml) of room
temperature distilled water into a tall glass container.
Do not use a metal or plastic container.
2.Place the Silver Wire Holder on the glass container
immersing at least 70% of the Silver Wires into the
water. Keep them at least 25 mm or 1 inch from the
bottom of the container.
3.Turn the unit ON by rotating the ON/OFF switch
clockwise until it clicks. It is not necessary to turn up
the intensity.
The ORANGE light will brighten as the current
increases up to the 1.0 mA limit.
4.Stir occasionally with a non-metal utensil. Occasionally, wipe off the grey or black
silver oxide that builds up on the Silver Wires.
5.Two cups (16 ounces or 500 ml) for 2 hours will produce a 5 to 8 ppm batch of
Ionic~Colloidal Silver, depending on the brand of distilled water. The concentration
of silver is measured in parts per million or ppm.
6.When nished, wipe the Silver Wires with paper towel to remove residue. Buff
lightly when needed to keep them free of sediment. Harsher bufng will wear away
the silver faster.
Notes:
Color: Ionic~Colloidal Silver remains colorless to about 5 or 6 ppm. At a slightly
higher ppm it will be a pale gold color. Do not drink if it is darker than pale gold or if

© 2012-2021 SOTA Instruments Inc. Page 12 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
it is dark grey as this indicates a higher level of impurities or larger particle sizes.
Clarity: The silver electrolyte should be clear. Do not drink if it is cloudy.
To Make Larger Quantities: The Silver Pulser can be used to make larger quantities
of Ionic~Colloidal Silver. For a concentration between 5 to 8 ppm, use the following
times as a guide:
For 4 cups or 1 liter: 3 to 4 hours.
For 1 gallon (16 cups) or 4 liters: 10 to 12 hours.
Storage: Pour the Ionic~Colloidal Silver into a dark glass bottle—never metal—and
store in a dark, dry place. Over time, light will degrade Ionic~Colloidal Silver by
turning the electrolyte grey or black. Discard if this occurs.
When made and stored properly, Ionic~Colloidal Silver retains freshness for many
weeks. It is suggested, however, that you use as soon as possible. If settling occurs, it
is losing potency. Do not drink any sediment.
Do not freeze, refrigerate, or expose Ionic~Colloidal Silver to extremes of
temperatures as its potency may be affected.
Save on Batteries: When making Ionic~Colloidal Silver the unit can be powered by
an AC-DC wall adaptor. See ‘Optional Power Input’ on page 13.
Switch Silver Wire Positions: The silver ions only come off the wire in the positive
(+) or anode terminal into the water. To equalize the wearing of the Silver Wires,
periodically exchange the position of the wires. If left in the same position, only one
Silver Wire will gradually wear away.
Replacing the Silver Wires: The Silver Wires are of the highest grade .9999 or 99.99%
or 4 Nine pure ne silver. When the SOTA pure Silver Wires wear too thin, do not
replace with sterling silver, as it contains nickel, which can be toxic.
TYPICAL USE
Quantity: There is no denite amount to drink. When consumed on a regular basis—
daily or several times a week—it is best to drink no more than 1 to 2 ounces
(30 to 60 ml) at a time.
Larger amounts of Ionic~Colloidal Silver—1 cup or more—can be consumed for
short periods of time, for example, a few weeks. It is better to take smaller amounts
throughout the day rather than all at once.

© 2012-2021 SOTA Instruments Inc. Page 13 of 14|www.sota.com
The Silver Pulser Model SP6 Manual
Length of Use: The SOTA Products User Guide available at
www.sota.com/spug offers suggestions for Focused, Basic and Ongoing Wellness
Plans.
General Guideline: 1 to 2 ounces (30 to 60 ml) or more daily for 2 or 3 months.
Ionic~Colloidal Silver can be used as needed. The initial program can be repeated at
any time. If using for an extended period, it is wise to take breaks.
Strength: Laboratory testing indicates Ionic~Colloidal Silver is effective as low as 2
ppm. When ingesting on a regular basis, it is suggested to limit the strength to less
than 10 ppm.
ELECTRICAL SPECIFICATIONS
POWER REQUIREMENTS
Use a 9–Volt Alkaline battery for proper operation.
OPTIONAL POWER INPUT
Both functions of the Silver Pulser can also be operated using NiMH rechargeable
batteries. When purchasing rechargeable batteries, it is suggested to take the unit
with you to ensure the batteries will t the enclosure.
To use a wall adaptor for making Ionic~Colloidal Silver the output should be from
6 to 12 Volts DC with a Tip or Center Positive pin and a minimum of 500 mA
(milliamperes) of current. The wall adaptor that comes with other SOTA units can be
used for making Ionic~Colloidal Silver.
Caution: Exceeding the voltage rating or reverse connection may result in injury
or unit failure. This will void the warranty.
To operate the Ionic~Colloidal Silver Function from a 12 Volt DC source, such as an
automobile battery or an appropriate Solar Panel, purchase a Universal Power Cord
with Tip or Center Positive.
OUTPUT SPECIFICATIONS
The output voltage is a nominal 31 Volts.
Micropulsing Application: Frequency through the metal pins is ~3.92 Hz or ½ of the
Earth Schumann frequency of 7.83 Hz, (+/- 1 Hz) with a Bi-Phasic Square Wave @ 31
Volts (+/- 1 Volt) peak per cycle.
Maximum current through the metal pins is ~8 milliamperes into 1,000 ohms, ~12
milliamperes into a short circuit at 31 Volts peak per cycle.

Made in China. Designed and Engineered in Canada.
• The SOTA units are consumer products designed to be used as part of a Wellness Lifestyle • The SOTA units are not medical devices nor are they
intended to diagnose, treat or cure any medical or health condition • The use, safety or effectiveness of the SOTA units has not been approved by any
government agency • Please consult a health practitioner for any medical or health condition • Results using the SOTA Products will vary for each
person • Please note that all purchases of SOTA Products are deemed to be made in Penticton, BC, Canada •
© 2012-2021 SOTA Instruments Inc. Page 14 of 14 |www.sota.com
The Silver Pulser Model SP6 Manual
Ionic~Colloidal Silver Application: The maximum current through the Silver Wires
is 1.0 milliamperes (+/- 0.5 mA) at 31 VDC compliance voltage when the Silver
Wires are touched together to short the circuit.
TROUBLESHOOTING
Troubleshooting Guides for both the Micropulsing and Ionic~Colloidal Silver
functions of the Silver Pulser are available at www.sota.com/manuals. These Guides
are a great tool to check if you are experiencing any issues with your unit.
COUNTRIES THAT PARTICIPATE IN MANUFACTURING
The manufacturing of the SOTA Products is a global collaboration. The following
countries have participated in the making of the Silver Pulser (listed in alphabetical
order): Canada, China, Hong Kong, Malaysia, Mexico, South Korea, Taiwan and the
USA.
REPLACEMENT ACCESSORIES
To replace your accessories, please contact your supplier.
WARRANTY
The Silver Pulser Model SP6 is covered by a three (3) year limited warranty. Please
keep proof of purchase. Warranty is void if the failure is due to abuse or negligence.
SOTA reserves the right to make changes to the Silver Pulser without obligation.
REPAIRS
Please contact your supplier for return instructions. For information about your closest
repair depot, contact [email protected] or call Toll-Free: 1.800.224.0242 (Canada &
USA) or 1.250.770.2023.