Sound Devices XL-SATA Operating instructions

XL-
S
ATA
S
ATA Drive Interface
for
7
22 and
7
44T Recorders
The XL-SATA Drive Interface allows the connection of most 2.5-inch SATA (Serial ATA) hard drives
to 722 and 744T models originally equipped with PATA (Parellel ATA) or IDE internal hard drives.
722s with serial numbers above 471309092000 and 744Ts with serial numbers above 461509071000 are
already equipped with 2.5-inch, 5400 RPM SATA hard drives. No additional interfaces are required.
XL-SATA Packing List
1) XL-SATA Drive Interface
1) Printed User Guide and Installation Instructions
2) Pink Protective Foam Rings
2) 3 x .5 mm Nylon Phillips Head Screws
5) 4-40 x 1.75” Black Oxide Phillips Head Screws
Equipment Not Included Required for Installation
1) #1 Phillips Head Screwdriver
1) 2.5” SATA Drive
Sound Devices recommends 5400 RPM hard drives or high quality solid state drives when choosing
a drive replacement. When choosing a substitute hard drive, note that higher RPM hard drives draw
more current, reducing battery run time. Higher speed drives may be used with the 7-Series Record-
ers, however they will not significantly improve performance. They will slightly increase transfer
throughput with the penalty of increased current draw and reduced battery run time. The 7-Series
can address drives with capacities up to 2 TB.
Replacing the Internal Hard Drive
The internal hard drive is not intended to be a swappable, deliverable medium. Its multi-pin con-
nector is not rated for repeated insertion and removal cycles and may be prone to breakage with
repeated cycling.
The hard drive is mounted to the bottom-side of the recorder’s chassis and is screwdriver acces-
sible. The drive is “suspended” in the unit with a shock absorbing material and is attached to the
main circuit board via a “flex board”. Since the unit’s high-density circuitry and tight construction
require specific electronics knowledge, Sound Devices strongly recommends drive replacement be
performed by a qualified technician using proper ESD precautions. Drive replacement done by a
qualified technician has no warranty implications.

XL-SATA User Guide and Installation Instructions
2
Installing the XL-SATA
1. Place recorder upside down on a steady flat, non slip surface.
2. With a #1 Phillips head screwdriver remove the screws in the following order. The five long black oxide screws will no
longer be needed. The two smaller screws (#4 and 5) will be needed for reassembly.
Attention: Remove screws in this order to avoid stripping.
4
4
3
3
1
1
2
2
6
6
5
5
7
7
3. Gently remove the bottom panel. As you remove the bottom panel be careful of the internal AA battery wires as they will
remain connected to the internal circuitry and the bottom panel.
4. Loosen the screw of the small green circuit board holding down the hard drive ribbon cable.

XL-SATA User Guide and Installation Instructions
3
5. Swing the small green circuit board over while pressing down on the ribbon cable to avoid snagging.
6. Carefully disconnect the ribbon head mating connector from the circuit board.
7. Remove the old hard drive and attached ribbon cable from the recorder.
8. Place the old hard drive assembly, and the five 4-40 x 1.75” Black Oxide Phillips head screws off to the side as these are no
longer needed. DO NOT DISCARD THE TWO SMALL BLACK OXIDE PHILLIPS HEAD SCREWS.
9. Remove the XL-SATA Drive Interface from its packaging.

XL-SATA User Guide and Installation Instructions
4
10. Connect the new SATA hard drive (not included) to the XL-SATA ribbon cable.
11. With the ribbon face up, attach the two new small nylon screws (included) using a #1 Phillips head screwdriver.
12. Slide the two new pink protective foam rings (included) over the new hard drive assembly to cover the mounting screw
areas.
13. Connect the XL-SATA ribbon header mating connector to the 7-Series circuit board connector.

XL-SATA User Guide and Installation Instructions
5
14. While holding down the ribbon cable, slide the small green circuit board piece over the ribbon header mating connector.
15. Using a #1 Phillips head screwdriver tighten the green circuit board piece securing the ribbon mating connector to the
circuit board.
16. Gently return the bottom panel to the all around panel.
17. Make sure all the tabs on the all around panel fit correctly in the bottom panel grooves.
18. Attach the bottom panel using a #1 Phillips head screwdriver, the original two small Black Oxide screws (#4 and 5), and
the five new Black Oxide screws (included). Install screws in the order defined in the illustration below. This may require
holding the bottom panel down firmly to the all around panel making sure that the tabs fit correctly.
Attention: Install screws in this order to avoid stripping.
4
4
3
3
1
1
2
2
6
6
5
5
7
7

XL-SATA - © 2009, Sound Devices, LLC - Printed in U.S.A.