Sound Storm SD320 User manual

1.2013
User Manual
SD320
SINGLE DIN MOUNTING
DVD/MP3/CD AM/FM RECEIVER
3.2” DETACHABLE WIDESCREEN TFT MONITOR
USB and SD CARD PORTS and AUX INPUT
3451 LUNAR COURT, OXNARD CA 93030
PHONE: 888.38.STORM
805.983.8008
FAX: [phone]
TECHNICAL SUPPORT
www.soundstormlab.com
SD320
SINGLE DIN MOUNTING
DVD/MP3/CD AM/FM RECEIVER
3.2” DETACHABLE WIDESCREEN TFT MONITOR
USB and SD CARD PORTS and AUX INPUT

CONTENT
-1-
Safety information.............................................................................
Installation steps...............................................................................
General knowledge about remote control ..........................................
Removing insulating sheet...................................................................
Replace lithium cell.............................................................................
Note about using remote control...........................................................
Warning for lithium cells of remote control.............................................
The functions of the buttons on the remote control............................
The functions of the buttons on the control panel.............................
Radio operation.................................................... ...........................
Media operation...............................................................................
Loading or unloading a disc, USB or card.........................................
Play modes.......................................................................................
Information on-screen display..........................................................
Digital Video special functions........................................................
Multi-subtitle languages.....................................................................
Multi-sound tracks.............................................................................
Multi-angles......................................................................................
Title menu.........................................................................................
MP3/WMA/JPEG/MPEG4 root menu..................................................
Media setup menu............................................................................
Systeml Setup ..................................................................................
Language Setup ...............................................................................
Video Setup .....................................................................................
Digital Setup ....................................................................................
External work source.......................................................................
AUX operation.................................................................................
Rear view camera.............................................................................
Specification...................................................................................
Troubleshooting..............................................................................
2
3
7
7
7
7
7
8
10
13
15
15
17
18
19
19
19
19
19
20
21
21
22
23
24
25
25
25
26
27

SAFETY INFORMATION
-2-
CAUTION:
THIS DIGITAL VIDEO PLAYER IS A CLASS I LASER PRODUCT. HOWEVER
THIS DIGITAL VIDEO PLAYER USES A VISIBLE/INVISIBLE LASER BEAM
WHICH COULD CAUSE .
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE
THE DIGITAL VIDEO PLAYER CORRECTLY AS INSTRUCTED.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.DO NOT OPEN COVERS AND DO NOT
REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
EQUIPMENT TO RAIN OR MOISTURE.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING
INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.
THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.
This product incorporates copyright protection technology that is protected
by method claims of certain U.S. Patents and other intellectual property rights
owned by Macrovision Corporation and other rights owners.Use of this
copyright protection technology must be authorized by Macro vision Corporation,
and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision Corporation. Reverse engineering or
disassembly is prohibited.
REGION MANAGEMENT INFORMATION:
This Digital Video Player is designed and manufactured to respond to the Region
Management Information that is recorded on a Digital Video disc. If the Region
number described on the Digital Video disc does not correspond to the Region
number of this Digital Video Player, this Digital Video Player cannot play this disc.

KEY PLATE
PLASTIC FRAME
KEY PLATE
If you want to take CHASSIS out of the SLIDE BRACKET HOUSING , first remove
the PLASTIC FRAME of the both sides away, then insert the two KEY PLATES into
left and right sides of chassis as above illustration.
1. Remove 2 screws for protecting deck;
1) Remove chassis from Slide Bracket Housing as bellows:
2) Remove 2 screws for protecting deck as right;
2. Connecting all wires
1) Making chassis wear Slide Bracket Housing again;
2) Remove control panel from chassis as follows:
A. Press the OPEN button to flip down control panel .
B. Slide control panel rightwards a little, and pull it towards you .
OPEN button
INSTALLATION STEPS
-3-

3) Connecting all wires as bellows:
NOTE:
1. Must use 4 ohms impedance of speakers.
2. Before finishing wiring, do not attach control panel onto chassis.
3. Maximum current of auto antenna is 200mA.
INSTALLATION STEPS
-4-
IGNITION SWITCH
RED
WHITE
WHITE/BLACK
GREY
GREY/BLACK
GREEN
GREEN/BLACK
VIOLET
VIOLET/BLACK
YELLOW
CONSTANT 12 VOLTS
BLACK
GROUND(B-)
BLUE
AUTO ANTENNA
FRONT
Lch SPK.
REAR
Lch SPK.
FRONT
Rch SPK.
REAR
Rch SPK.
BROWN
(B-) PARKING BRAKE
PINK
RADIO ANTENNA JACK
(B+) 12V
REAR CAMERA SWITCH
REAR CAMERA INPUT
YELLOW
GREY
SUB WOOFER
VIDEO IN (yellow)
AUDIO R OUT (red)
AUDIO L OUT (white)
VIDEO OUTPUT (brown)
FUSE
ISO CONNECTOR

4) Attach control panel onto chassis.
A. Make the right hollow of control panel aim at the right bulge of chassis, then push
and hold control panel rightwards; at one time, move the left end of control panel
towards chassis to make the left hollow of control panel aim at the left bulge of
chassis and then release holding .
B. Flip control panel up till hearing a click sound to attach onto chassis.
* How to clean panel connector
Frequent detachment will deteriorate panel connectors. To minimize deterioration,
periodically wipe the panel connectors with a clean/soft/dry cloth .
5) Testing it for making sure that it can work properly .
Bulge
Hollow
Bulge
Hollow
Connector
Installation diagram
INSTALLATION STEPS
-5-
DASH BOARD
METAL MOUNTING
STRAP
HEX NUT
SPRING WASHER
PLAIN WASHER
TAPPING SCREW
CONSOLE
SLIDE BRACKET
HOUSING
HEX BOLT

3. Installing main unit according to installation diagram on the previous page:
1) Mount the sliding metal housing in the position of car multi-media system and
bend some tabs of sliding metal housing to fix sliding metal housing.
2) Insert the chassis of the car multi-media system into the sliding metal housing.
3) Use the metal strap to fix the rear part of chassis.
* Uninstalling main unit:
1) Remove metal strap from main unit;
2) Remove plastic trim frame from main unit;
3) Insert a key plate into left and right side of main unit and draw main unit out of
sliding metal housing.
INSTALLATION STEPS
-6-

1. Removing insulating sheet
If
)
)
)
.
)
)
)
.
)
)
using remote control for the first time, you
can see an insulating sheet at the bottom
side of remote control as right.
you must remove the insulating sheet as right.
Otherwise, the remote control is disabled.
2. Replace lithium cell
If the electric energy of lithium cell is weak,
replace it.
1 Press and hold the movable block as direction
indicated by arrow 1 as right, at one time pull
cell holder out of remote control as direction
indicated by arrow 2 as right.
2 Replace the old cell by a new one with (+)
polarity side upward as right.
3 Insert the cell holder into remote control again
as right.
3 Note about using remote control
1 You should face the emitting window of remote control towards the sensor
window of the unit.
2 Operation angle for front panel: About 30 degree
3 The distance between the emitting window of remote control and the sensor
window of the unit : < 5M .
4 Warning for lithium cells of remote control
leakage may cause damage to remote control.1 Cell
2Do not throw cells into fire, it may cause explosion.
.
3.To avoid risk of accident, keep cells out of reach of children.
GENERAL KNOWLEDGE ABOUT REMOTE CONTROL
-7-

THE FUNCTIONS OF THE BUTTONS ON THE REMOTE CONTROL
-8-
1. CLK Press it briefly to show the clock.
2. MODE Press it to select a desired work
source .
3. STOP Press once to pause playback,
then press PLAY/PAUSE to resume play-
back . Press twice to full-stop playback,
then press PLAY/PAUSE to play from the
beginning of the media.
4. SETUP Press it to pop up or disappear
the SETUP menu.
5.MO/ST(AUDIO) In radio mode, press it
to select STEREO or MONO mode (when
a station is weak, sometimes switching
to Mono will improve sound quality ) .
6. LO/DX(SUBTITLE) Changing of the
SUBTITLE language on multi-subtitle
language Digital Video media. In radio
mode, Press this button for distance
reception when you are located at weak
signal location, depress it for stronger
signal.
7. REPEAT Switch the Repeat mode
in media mode.
8.GOTO Press this button to begin
playback at a moment in the program you
designate. Use the number buttons to
enter the data that is needed.
In Digital Video mode, pressing it button
opens the AUDIO setup menu for making
changes to the way te soundtrack is
reproduced
15
17
19
13
14
7
2
6
22
11
18
3
16
5
20
1
21
24
9
12
10
48
26
23
25

-9-
THE FUNCTIONS OF THE BUTTONS ON THE REMOTE CONTROL
9. / Press to skip to the next
track & press to skip back one track.
-
,
n
+ or VOL- button
11. VOL+/VOL- Press it to adjust volume
level .
12. / / / Use these buttons to
navigate the various menus present in the
product.
13. MENU/SUB WOOFER Press it to
display the root menu of the Digital Video
media.
14. BAND(OSD)
.
15. POWER ( ) Press it to turn on the
unit , press it again to turn off.
16. PLAY/PAUSE ( ) In media mode,
press it to pause or resume playback.
17. MUTE
18. TITLE/PBC (A/P) Display the TITLE
menu which
changing between PBC ON
and PBC OFF on the VCD media.
10. Briefly press to switch between
BASS, TREBLE, BALANCE, FADE,
COLOR, BRIGHTNESS, CONTRAST,
TINT and VOLUME; Long press to dis
play LOUDNESS then briefly press to
switch between SUBWOOFER, EQ,
LOCAL/DX(in radio mode), STEREO/
MONO(in radio mode), CLK FMT, SET
CLK, FREQUENCY AREA, ANIMATION
and WALLPAPER. After selecting a
item above, use VOL to
adjust.
Press and hold this button to turn
ON or OFF the SUBWOOFER output.
In Radio mode, press
this button repeatedly to switch between
the five radio bands
In media playback mode, Press this
button to see information about the media
currently in play.
Press this button to turn off the
audio. Press again to restore the sound
to its prior volume level.
SEL
is recorded on the Digital
Video media;
In radio mode, press shortly to scan the
preset station, press longer to enter into
automatic memory storing function .
19. ZOOM Press this button to active
the ZOOM function . Each press of the
zoom button changes the screen in the
sequence : 2x 3x 4x ½ 1/3 1/4 .
Use the / / / buttons to move
through the zoomed picture .
Note : during the JPEG playback, press
the ZOOM button, the “ZOOM 100%” will
appear on screen, then press the /
button to increase/decrease in size,
use the / / / buttons to move
through the zoomed picture .
20. ANGLE Changing of the view angle
on multi-angle Digital Video media.
21. EQ
22.
In media mode,
23. ENTER
24. 0 - 9 These buttons are used for
numeric entry in many different menus.
25. +10 Tens digit select button,
cooperatively used with numeric buttons.
26. RADIO PRESET Six preset memory
buttons.
Press it briefly to turn to
equalization function. Press it longer to
switch the LOUDNESS function ON or
OFF .
This button is used to
confirm selections and settings within
many of the menus in the OSD system.
Press to start forward
rapidly.press to reverse rapidly.

-10-
THE FUNCTIONS OF THE BUTTONS ON THE CONTROL PANEL
2. (POWER On/Off) Button
Press this button to switch the device On.
Press it again to switch the device Off.
1. OPEN Button
Press it to flip down the front panel , then
you can insert the CD disc into the CD
compartment. You can also press the
Eject button to eject the disc.
14
13
Control Panel
2
1
15
17
8
16
3
7
611
4
10
9
12
18
3. SEL button and VOL knob
To switch between VOLUME,BASS,
TREBLE,BALANCE, FADE, COLOR,
BRIGHTNESS,CONTRAST and TINT,
short press SEL button continuously.
After switching on a desired mode above,
rotate VOL knob to set it.
To switch between LOUD, SWF, EQ,DX/
LOCAL(in radio mode), STEREO/MONO
(in radio mode), 24/12H, SET CLOCK,
EUR/USA FREQ,ANIMATION and WALL-
PAPER, long press SEL button to switch
on LOUD, then short and repeatedly
press SEL button.
After switching on a desired mode above,
rotate VOL knob to set it.
The Base of Control Panel
5

-11-
THE FUNCTIONS OF THE BUTTONS ON THE CONTROL PANEL
5. EQ Button
Press the EQ button briefly to turn to
equalization function and to select
desired audio mode.
There are five kinds of modes as follows:
Press it long to switch the LOUD
function ON and OFF .
JAZZ CLAS POP ROCK USER
6.APS Button
Automatic storing stations in memory:
In Radio mode, press and hold the APS
button for about 2 seconds to active
automatic station storage. The radio
searches within the current frequency
band, e.g. FM1, for the strongest station
are then allocated to the corresponding
storage locations. Then the station of
the first storage location is set. If you
would like to search for more stations
in the FM band, press the BND button
in order to change to the FM2 or FM3
band. Press it long again for about 2
seconds to continue search.
Scanning stations in memory:
In Radio mode, press it briefly to scan
and play all the preset sations in order,
and it will hold at each band for about 5
seconds . If you like one of them, press
the PLAY/PAUSE button to stop the
scanning .
7.MUTE Button
Press this button to turn off the audio.
Press again to restore the volume to the
prior level. You can also disable the
MUTE function by rotating the VOL knob.
B) In Radio Mode
you can store 30 stations in memory:
18 FM stations and 12 AM(MW) stations,
each band stores up to six preset
stations .
The operation as below :
-Storing a station in Memory
> Select the frequency band
> Press repeatedly the button to select
the desired memory key .
> Select the station
> Keep the desired memory key pressed
in until the station is heard again after
a brief interruption .
-Retrieving a station in memory
press the button repeatedly to retrieve
a station which had been stored in the
memory in advance the chose number
is shown on display .
8. CH 1-6 (RADIO PRESET) or
A). In Media Playback Mode
Press this button to pause playback,
press it again to resume playback.
9/10 . / Buttons
(tune, Seek, Track, Skip Up/down)
a) In media mode:
if you wish to jump forwards or back-
wards,press briefly the or button.
long over and over f f
backword in various speeds
Press to ast orward
or .
b) In Radio Mode:
Press the or button
to start the
search for a radio station
briefly to manu-
ally tune the radio in single steps. Press
and hold for two seconds
automatically.
4. BAND Button
In Radio mode, press this button repeat-
edly to cycle through and select the
desired radio band, the designation of
the corresponding level- FM1, FM2, FM3,
AM1(MW1), AM2(MW2)- is shown in the
TFT.

-12-
THE FUNCTIONS OF THE BUTTONS ON THE CONTROL PANEL
12. (EJECT) Button
In DISC playing ,Press the Open button
to flip down the control panel, then press
the EJECT button to eject the disc in the
disc compartment or pull the disc ejected
into the disc compartment .
14. IR (Infrared)
Sensor window for the remote control .
13. RESET Button
To push the RESET button, press the
OPEN button to flip down the control
panel and remove the control panel, then
push the RESET button with either a
ballpoint pen or thin metal object.
The RESET button is pushed for the
following reasons:
A. Initial installation of the unit when all
wiring is completed.
B. Some function buttons do not operate.
C. Error symbol display on the display.
15. AUX IN JACK
For information about using an AUX IN
audio source, refer to AUX operation.
17. TFT Display
16. USB PORT
18. SD/MMC CARD SLOT
11. SRC Button
Press it repeatedly to select RADIO,
DISC, USB, CARD or AUX IN mode.

RADIO OPERATION
-13-
To switch between ST and MO
Press the ST/MO button on the remote
control to select the MONO or STEREO
mode(When STEREO mode is activated,
the ST symbol will appear).
When the STEREO mode is activated,
it can get better audio effect; when the
MONO mode is activated, it can get
clearer audio signal.
Selecting a band
Repeatedly press the BAND button to
select a desired band, the message
will show in turn :
FM1 FM2 FM3
AM2(MW2) AM1(MW1)
Entering radio mode
Press the MODE button to select the
RADIO mode, the message will display
as follows :
Long press the “ or ” button on the
remote control to search for an available
radio station automatically .
To switch between LO and DX
Press the LO/DX button on the remote
control to select the LOC or DX mode
(The word “LOC” or “DX” will appear).
When the LOC mode is activated, it can
decrease interfere for tuning the local
stations; when the DX mode is activated,
it can increase singal strength for tuning
the distance station.
Storing or retrieving a
station in memory
A total of 30 stations can be stored in the
memory banks of 6 number buttons.
Each band stores up to 6 preset stations.
These bands are FM1, FM2, FM3, Am1
(MW1) and AM2(MW2).
The operation is as follows :
- Storing a station in Memory
>Select a band
>Select a station
>Long press a button from 1~6 buttons
till the color of the memory bank code
and its frequency(being alternated by
the current frequency) is changed.
Searching for a station
In radio mode, briefly press the
button on the control panel to increase
frequency by one step of channel
spacing . (Or press the button on the
remote control)
Manual Search
In radio mode, briefly press the
button on the control panel to decrease
frequency by one step of channel
spacing . (Or press the button
on the remote control)
Automatic Search
In radio mode, press and hold (for more
than 2 seconds ) the “ / ” button
to start search for an available radio
station automatically .
LOC ST USER
101.60
FM2 MH2
187.50
290.10
398.10
4105.30
5106.20
688.20
WELCOME TO......
LOC ST USER
101.60
FM2 MH2
187.50
290.10
398.10
4105.30
5106.20
688.20
WELCOME TO......

-14-
In radio Mode, press and hold (for more
than 2 seconds) the APS or A/PS button
to activate the automatic search mode.
The radio searches within the current
frequency band, e.g. FM1, for the strong
signal stations until the entire cycle
has finished . The six strongest stations
are then allocated to the corresponding
memory banks in the current band .
. presetting
The presetting function can be implemented
in selected FM or AM band. (It can presets
3x6 stations for FM and 2x6 stations for AM
in all) After finishing , it will
resume broadcasting the station in NO.1
bank.
Automatic storing stations in
memory and scaning them
Automatic storing stations in
memory
Scanning stations in memory
In radio mode, briefly press the APS or
A/PS button , the radio scans
or scanned
or
scanned
for each
preset station in FM or AM band from NO.1
bank, each preset station broadcasts for 5
seconds. After finishing a circle of scanning,
it will resume broadcasting the station in
NO.1 bank.
NOTE: In FM band, FM1,FM2 and FM3 are
preset as one band at a time; In
AM band,AM1 and AM2 are preset
as one band at a time.
- Retrieving a station in memory
press one of the 1~6 buttons briefly on
the remote control to retrieve a station
which had been stored in the memory
bank of the number button in advance,
the color of the memory bank code
and its frequency is changed.
RADIO OPERATION

Loading or unloading a disc, USB or card
1. Loading a disc, USB or card
To play files in a disc, press OPEN button to flip down control
panel, then insert a disc with label surface up into disc slot,
and then attach control panel onto chassis again, by now it
will automatically play.
* CAUTION OF USING A DISC
1) Handle a disc by its edge, do not touch the surface of play side.
2) Before inserting disc, wipe the disc outwards from the disc center
with a clean, soft, dry, lint-free cloth. Do not use solvents/thinner
such as petrol/benzine, cleaner.
3) After taking a disc out of disc slot, put the disc inside disc case to
keep it clean.
4) Do not stick paper or tape on the disc surface of play side. If
there is glue (or analog) on the disc surface, must wipe it up
before using.
To play files in a USB, firstly open USB port cover, then insert USB storage into
USB port, and then it will play files in the USB automatically.
To play files in a card, firstly press OPEN button to flip down control panel and
remove it, then insert the card into card slot as bellows, and then attach control
panel onto chassis again, by now it will play files in the card automatically .
2. Unloading a disc, USB or card
To unload the disc in disc slot, use STOP button to stop playback and then press
OPEN button to flip down control panel and press EJECT button to eject disc and
then remove it.
Label
surface up
Label side
facing upward
MEDIA OPERATION
-15-

To pull away the USB storage, use STOP button to stop playback, then you can
remove the USB storage.
To unload the card in card slot, use STOP button to stop playback, then press
OPEN button to flip down control panel and then remove it, and then you can push
the card for release it and then pull it out of card slot.
* During MP3/WMA playback, the information of file, folder, title, artist and album
will be scrolling on LCD display. As long as the current playing MP3/WMA music
contains relevant ID3 tag information in version 1.0/2.0 format, the 3 items
underlined above will be scrolling on LCD display; otherwise, they will not.
* There is ESP function for all formats of discs.
MEDIA OPERATION
-16-

-17-
MEDIA OPERATION
SELECTING PLAY MODE
During disc playback, press the
“REPEAT, RDM, INT ” button on the
remote control to select the different
playing modes .
2). REPEAT FUNCTION
REPEAT OFF
REPEAT ONE REPEAT ALL
FOR VCD/CD :
Press REPEAT button on the remote
control to select REPEAT mode as
follows :
FOR Digital Video :
Press REPEAT button on the remote
control to select REPEAT mode as
follows :
REPEAT ALL
CHAPTER REPEAT ON TITLE REPEAT ON
REPEAT OFF
123
45 6
789
SEL
SEL
VOL
VOL
TOP INT
RDM
1). TOP FUNCTION
ForDigital Video/ VCD/CD/MP3:
When playing Digital Video/VCD/CD/
MP3 discs, press the button to select the
first track/chapter to play.(
)
For VCD it
depends on which disc is used
3). INTRO FUNCTION
FOR CD :
Long press the 3/INT button on the
remote control to play the first 10
seconds of each track/chapter on the
disc.
(Long press again to cancel this mode)
FOR VCD :
Long press the 3/INT button on the
remote control, the following menu
will be displayed:
SEQ PLAY INTR O 1
Note: When INTRO 1 mode is selected,
the first 10 seconds of each track/
chapter on the disc will be played. (Long
press it again to cancel this mode .)
FOR Digital Video/MP3 :
For Digital Video/MP3 , the INT button is
not available .
4). RDM (RANDOM) FUNCTION
During DISC playback, long press the
4/RDM button on the remote control to
play in random. Each playing order
is different .
().
Long press it again to cancel this
function .
For VCD it depends on the disc used
FOR MP3 :
Press REPEAT button on the remote
control to select REPEAT mode as
follows :
REPEAT ALL
REPEAT ONE REPEAT FOLD ER(or DIR)
REPEAT OFF

-18-
MEDIA OPERATION
NOTE:
For CD(audio) Disc, press OSD button
is not available .
E. Press OSD for the fifth time:
The message on the screen will be
cleared for SVCD and VCD.
2.Example for VCD/SVCD/CD:
F. Press OSD for sixth time:
The message on the screen will be
cleared.
ON-SCREEN DISPLAY FUNCTION
Digital Video TT 01/01CH 04/31 C -0:01:32
C. Press OSD for third time:
During playback, press the
OSD button on the remote
control . It will display the
following as bellow :
1. Digital Video:
A. Press OSD for first time:
Title Number, To ta l Title Number,
Chapter Number, Tot al Chapter Number
of this Title of the disc currently being
played will be shown on the screen,
along with the elapsed time.
Digital Video TT 01/01CH 04/31 C 0:02:06
D. Press OSD for fourth time:
Digital Video TT 01/01CH 04/31 T 0:16:00
E. Press OSD for fifth time:
Digital Video TT 01/01CH 04/31 T -1:36:55
B. Press OSD for second time:
A. Press OSD for first time:
VCD TRK 1/19 PBC C 0:01:36
A
B. Press OSD for second time:
VCD TRK 1/19 PBC C -0:06:06
A
C. Press OSD for third time:
VCD TRK 1/19 PBC T 0:02:12
A
D. Press OSD for fourth time:
VCD TRK 1/19 PBC T -1:23:06
A
3. Example for MP3
A. Press OSD for first time:
CDrom TRK 2/76 C 0:00:36
A
B. Press OSD for second time:
CDrom TRK 2/76 C -0:03:38
A
C. Press OSD for third time:
The message on the screen will be
cleared.
½ ENG 2CH OFF AN OFF
The underlined part is different from
the used discs.

-19-
MEDIA OPERATION
Digital Video Special Function
Notes:
- The angle number is different
according to the disc.
- The function only work for disc having
scenes recorded at different angles.
- When no different angle are recorded,
will be displayed at
screen left top corner.
“ INVALID KEY ”
During Digital Video playback,
press the ANGLE button on the
remote control
3. Multi-Angle Function
(for Digital Video Only)
Each time the button is pressed , the
number of the angle changes in sequen-
tial order.
4. Title Menu Function
For Digital Video:
If the Digital Video has multiple titles
recorded on the disc. It can select
preferred title from the title menu to start
playback.
- During Digital Video playback, press
TITLE button on the remote .The title
menu is display.
- Select preferred title by the cursor
button and confirmed by press the
ENTER button .
For VCD:
Press TITLE/PBC button on the remote
control while the disc is playing, you can
switch between "PBC ON"and "PBC off"
mode.
MONO LEFT MONO RIGHT
STEREO
MIX-MONO
For VCD:
during playback, Press AUDIO on the
remote control . It is possible to switch
the sound between monaural and
stereo sound.
Notes:
- The language number is different
according to the disc.
- Some disc only contain one language
soundtrack
- When no different language soundtra-
ck are recorded will be
display at screen left top corner.
“ INVALID KEY ”
2. Multi-Audio Language Function
For Digital Video:
During Digital Video playback,
press the AUDIO on the remote
Each time the button is pressed number
changes on sequential order.
Notes:
- The language number is different
according to the disc.
- Some discs only contain one subtitle
language.
- When no different subtitle language
are recorded, “ INVALID KEY ” will be
displayed at screen left top corner.
During Digital Video playback.
press the SUBTITLE on the
remote control .
1. Multi-subtitle Language
Function (for Digital Video Only)
Each time the button is pressed number
of the subtitle language changes
in sequential order.