Sound Tube HP82-EZ-WH Configuration guide

Box contents
©2015 SoundTube Entertainment, Inc. All rights reserved. INS-HP-EZ Rev 12.04.2014 - Rev 2
Document Reference Number RSEZ0003
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.
HP-EZ series
Speaker
Cover Plate
Cover Plate
Screws (4)
Hanging Hardware
Tap Switch
Hanging Bracket
Terminal
Block
Weather plug
1 Speaker
1 Cover Plate w/ 4 screws
1 Rubber weather plug
1 Hanging kit
Install Instructions For:
HP82-EZ-WH & HP82-EZ-BK
1.435.647.9555 |800.647.TUBE | www.soundtube.com
Do not spec or install speaker near support beam, ventilation duct or
other structure that may interfere with speaker function or dispersion.
Warning Warning
SoundTube speakers must be installed by a professional audio installer/contractor. For safety and for
optimum audio performance, installer must follow all directions issued by SoundTube Entertainment.

1. Unpack speaker and
SpeedClamp™ mounting
hardware.
2. Thread hanging or safety
cable through SpeedClamp™
mechanisms as shown.
3. Attach the hanging cable
by securing it and safety
cable to structure as
shown.
4. Thread cable end(s)
through SpeedClamp™
mechanisms as shown.
9. Connect signal wires to
(+) and (-) inputs. Use extra
(+) and (-) for daisy
chaining.
11. Place cover plate onto
top of speaker and rotate
clockwise until alignment
indicators meet.
12. Tighten all four (4) screws
to lock cover plate in place.
5. 7a. Attach hanging cable
by (1) inserting into side of
mounting bracket and (2)
rotating to align with center
slot in hanging bracket.
6. Slide cover plate over
hanging and safety cables
and run signal wire through
center hole.
10. Select desired tap
position. Switch is preset to
maximum 70.7V (100V)
mode.
7b. Once aligned with central
slot, pull cable up into slot to
secure. Repeat steps 7a and
7b with secondary safety ca-
ble into one of the side slots.
Adjust speaker hanging
height with SpeedClamp™
mechanism. Pull to tighten &
press button on SpeedClamp
as shown to loosen or adjust.
13. Install rubber weather
plug by sliding slit over the
wire, then pressing snuggly
into hole in cover plate.
14. Done.
8. Extra slot and 2 holes
provided for additional
safety cables where
needed.
1.
2.
1.435.647.9555 |800.647.TUBE | www.soundtube.com
Install Instructions For:
HP82-EZ-WH & HP82-EZ-BK
HP-EZ series

4. Run signal wire and at
least one safety cable
through conduit.
5. Attach safety cable by
rst inserting into side of
mounting bracket.
6. Align safety cable with
center slot and pull up to
secure.
2. Securely mount conduit
to structure. Conduit must
have 3/4” NPT thread to
accomodate RS-EZ
speaker.
3. Thread cover plate on to
conduit until secure.
7. Connect signal wires to
(+) and (-) inputs. Use extra
(+) and (-) for daisy
chaining.
8. Select desired tap position.
Switch is preset to maximum
70.7V (100V) mode.
1. Unpack speaker from
box.
9. Line speaker up with
cover plate and rotate to
lock in to place. Alignment
marks will meet when
secured.
10. Tighten all four (4) screws
to lock speaker in to cover
plate.
11. Done.
1.
2.
1.435.647.9555 |800.647.TUBE | www.soundtube.com
Install Instructions For:
HP82-EZ-WH & HP82-EZ-BK
HP-EZ series
Conduit Installation:
Note: Conduit is not an approved mounting method for UL1480 installations

Install Instructions For EN54-24 Compliance
EN54-24
In order for this speaker to be EN54-24 compliant, a 3/8" NPT wire gland and a 3/4" to 3/8" NPT adapter have been included with
the product. These items must be installed according to this document to be EN54-24 compliant.
3/8" NPT Wire Gland 3/4" to 3/8" NPT Adapter
1. Thread the 3/4" to 3/8" NPT
adapter into the the top plate of the
speaker in the hole provided. Make
sure to tighten securely to ensure a
water tight t.
Installation
2. Thread the 3/8" NPT wire gland
into the 3/4" to 3/8" NPT adapter.
Make sure to tighten securely to
ensure a water tight t.
3. Thread the speaker security
cable through the 3/8" NPT wire
gland and attach to the back of the
speaker as noted in the installation
instructions.
Tighten the top of 3/8" NPT wire
gland such that the rubber grom-
met is tight around the cable. This
may require a wrench.
4. Thread signal wires through the
provided conduit knockouts.
Note: A water tight conduit connection
must be used in the knockout locations
in order to be EN54-24 complient
5. Done