Sound Tube IPD-CM52-BGM Configuration guide

SOUNOTUSE Lead. or to/low.
IPD-BGM Series I
Tile bridge -----::=_.
Cover plate
Box contents
Speaker
Flexible conduit clamp
Cover plate
Grille
Installation aid/paint mask
Install Instructions For:
IPD - CM52s-BGM, IPD-CM52 - BGM, IPD-CM62-BGM, and IPD- CM82 - BGM
Ceiling thickness tolerances
Max
40.9 mm (1 .60 in)
Secondaryattachmentpoint
SpeedWingTM mountingarms
Installationaid/paintmask
~----Grille
----- Grillesafety restraint
•
1.435 . 647.9555I800.647.TUBE I www .soundtube.com
©2013SoundTube Entertainment, Inc. All rights reserved. PN INS-IP-BGM Rev1 .20.2013
Warning Warning
SoundTube must be installed by a profess1onal audro installer/contr2ctor. For safety ar'd for oottmun~ audio
performance must follow all dtrect;ons issued by SoundTube En!e'tainr'le"lt
rnstJ.IIateur CO'llracor de
1
audio Oil18i. Par :nes .. :re de
et pow des performances audro ! ns:allateur cart suivre toutes les '/es er..,rses par SoundTube
Ertertarnment

IPD-BGM Series IInstall Instructions For:
IPD-CM52s-BGM , IPD-CM52-BGM , IPD-CM62-BGM , and IPD-CM82-BGM
Important Safety Instructions
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9) Only use the attachments/accessories specified by the manufacturer.
1
0) Unplug this apparatus during lightning storms or when unused for long periods of time.
11) Refer
all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Consignes de securite importantes
1) Lisez ces instructions.
2) Conservez ces instructions.
3) Respectez tous les avertissements.
4) Suivez toutes les instructions.
5) Ne pas utiliser cet appareil pres de l'eau.
6) Nettoyer seulement avec un chiffon sec.
7) Ne pas bloquer les ouvertures de ventilation. Installer conformement aux instructions du fabricant.
8) Ne pas installer pres de sources de chaleur telles que des radiateurs, registres de chaleur, poeles ou autres
appareils (incluant les amplificateurs) qui produisent de
Ia chaleur.
9) Utiliser uniquement les fixations I accessoires specifies par le fabricant.
1
0) Debranchez cet appareil pendant les orages ou si inutilise pendant de longues periodes de temps.
11) Confiez toute reparation a un personnel qualifie. Une reparation est necessaire lorsque l'appareil a ete
endommage de quelque
fac;;on que ce cordon d'alimentation ou Ia fiche est endommage, l'appareil a ete expose a Ia
pluie ou al'humidite, s'il ne fonctionne pas normalement ou s'il est tombe .
1.435 . 647 . 9555I800.647 . TUBE I www .soundtube.com

Install Instructions For:
IPD-BGM
Series
I
IPD-CM52s-BGM, IPD-CM52-BGM, IPD-CM62-BGM, and IPD-CM82-BGM
1. Unpack speaker & set
aside grille assembly.
Ceiling preparation -For Tile Ceilings
2. Use included tile bridge
to
mark cutout
in
tile.
3.
Use Rotozip or other tool
to cut hole.
Hole Diameters
All
BGM models
266
.7
mm
(1
0.50
in)
Ceiling preparation -For Sheetrock
I
gypsum board ceilings
2.
U
se
in
cluded tile bridge 3. U
se
Rotozip or other tool
to
mark cutout
in
sh
ee
trock.
to
cut ho
le
.
Hole Diameters
A
ll
BGM models
266
.7
mm
(1
0.50
in)
1
.435.64
7.9
555
I800
.64
7
.T
UB
E
I
www.
so
undtube.com

lp
tn\
BGM
Series
Jlnstall Instructions For:
,.,,-
IPD-CM52s-BGM, IPD-
CM52-BGM,
IPD-
CM62-BGM,
and IPD-CM82-BGM
Ceiling preparation -For
all
other ceiling types
2.
Nail
or screw bracket to
joists. Secure conduit/signal
wire away from hole
in
bracket. Once installed,
complete finish work.
4.
Run
signal wires through
conduit, terminate with
RJ45 connector, then plug
into speaker. If local power
is
required at speaker
(non-POE installation),
connect appropriate DC
power supply
to
barrel
connector on speaker input
panel. Contact SoundTube
for questions about
installations requiring local
power.
l f
8.
Once
all
painting and finish
work
is
completed, remove
the paint mask.
3.
Use Rotozip or other tool
to cut hole.
Hole Diameters
All
BGM models
266.7
mm
(10.50
in)
5.
Tighten screw on terminal
plate, and push conduit
connector into knockout.
-2.
9.
Attach grille safety clip by
placing the large end ofthe
clip over snap-fit post
(1
),
then sliding clip until small
end snaps into place around
post
(2).
6. If required, a sheet-metal
tab located on the rear
panel ofthe speaker serves
as a secondary point of
attachment (cable not
included).
l
10. Press grille into place.
7.
Insert speaker into
mounting hole with
installation aid
in
place.
Screw down both bolts on
the baffle face
to
actuate
the mounting wings. Firmly
secure both bolts -
do
not
over-tighten.
c.___::)
l-r
1
11.
Done!
1.435.647.95551
800.647.TUBE
I
www.soundtube.com