Sound Tube SM-EZ Series Configuration guide

SOUNOTUSE . 0 Lead. or follow.
· 'Install Instructions For:
SM- EZ Series sM52-EZ-BK. sM52-EZ-WH. sM52-EZ-WX-BK. sM52-EZ-wx-wH.
SM82-EZ-BK, SM82-EZ-WH, SM82-EZ-WX-BK & SM82-EZ-WX-WH
Box contents
1 -Speaker
1 - U-bracket
2 - U-bracket screws
2 - Screw caps
- Allen wrench
1 - Back plate
1 -Port plug
1 - Safety cable
1 - 3/4" Conduit connector
Condu1t connector
~
U-bracket
0
0
Screw cap
I U-bracket screw
T_/
0
00
0
0
Back plate
1.435.647.9555 I 800.647.TUBE I www.soundtube.com
©20 16SoundTube En t ertainment, I nc . Al l rights r eservec. PN IN S-S M -EZ Rev02-1 0-2016
m
Warning
SoundTube speakers must be 1nstalled by a profess1onal aud10 Installer/contractor For safety and for
opt1mum aud1o
performance mstaller must foll ow all d~rect 1 ons 1ssued by SoundTube Entertamment m
Warning
Do not spec or Install speaker near support beam, ventilation duct or
other structure
that may Interfere w1th speaker funct1on or d1spers1on

SM
Ez
S . IInstall Instructions For:
-er1es SM52-EZ-BK, SM52-EZ-WH, SM52-EZ-WX-BK, SM52-EZ-WX-WH,
SM82-EZ-BK, SM82-EZ-WH, SM82-EZ-WX-BK & SM82-EZ-WX-WH
1. Unpack speaker and
mounting hardware.
5. Run signal wires through
conduit connector then
connect to ceramic terminal
strip.
Two + (plus) and two -
(negative)
connectors are
provided for daisy chaining.
9. Tilt speaker
45° (grille up)
and slide on to bracket.
--
-- :;il..:-- -------
1 II-- r
I I I
I
II I I
II~ II
I II I I
11~ II
I II I I
Ill-~
I c.--
: II --1''1
I II I I
I I
2. Choose a secure mounting
surface with sufficient strength
to reliably hold the speaker.
The speaker may be mounted
in either the vertical or the
horizontal position
with the
same U-bracket.
6. Select the
tap position by
rotating the rotary switch
located on the back of the
speaker to desired setting. The
switch is preset to the
maximum tap setting in 70.7 V
mode (32W for the
SM52-EZ[-WX) and 64W for
the SM-82-EZ-11[-WX)).
10. Aim speaker and tighten
u-bracket screws. Once
tightened down, place the
screw caps on the screws.
Done!
3.
Mount u-bracket with
clamping slots pointing
upward. Securely fasten
mounting bracket and safety
cable
to surface (user must
supply fasteners).
Note: The safety cable will
attach
to the U-bracket
clamping screw on one side of
the cabinet.
- ----- - ....
7. Install back plate and
secure with included fasteners.
Port protection for SM-EZ
{
To enhance protection of
internal components from
humidity and other potentially
corrosive elements, use
provided
port plug to seal
enclosure. Use RTV silicone
around edge of the port plug
for increased protection.
Note:
WX versions will come with the
port plug pre-installed.
4.
If conduit is to used for
signal wires,
attach the
included conduit connector
to the back plate. If conduit is
not required, skip this step.
8. Select desired location for
safety cable and remove
the
U-bracket screw from that
side. Attach safety cable to the
clamping screw and reinstall
loosely.