SOUNDMASTER UR270 User manual

UR270 / English Instruction Manual
1
FUNCTION AND CONTROLS
1. ALARM 1 ON -OFF SET/ VOLUME DOWN
2. ALARM 2 ON -OFF SET/ VOLUME UP
3. << / TUNE - / YEAR/MONTH/DAY
4. >> / TUNE + / DISPLAY LIGHT AUTO ON/OFF
5. NIGHT LIGHT ON/OFF/AUTO-SENSOR ON-OFF
6. TO SET THE NIGHT LIGHT INTENSITY LOW-HIGH
7. AUTO-SENSOR FOR NIGHT LIGHT
8. TIME SET/MEMORY/MEMORY+
9. SNOOZE / SLEEP / DIMMER/DST
10. ON / OFF
11. RATING LABEL
12. DISPLAY
13. NIGHT LIGHT
14. SPEAKER
15. BATTERY COMPARTMENT
16. AC POWER CORD
17. FM ANTENNA

UR270 / English Instruction Manual
2
LED DISPLAY
Power connection
Plug the AC power cord to a household outlet AC source. This unit is equipped with a battery
back up system, it requires a 3V CR2032 flat lithium battery (not included). Insert the battery in
the battery compartment, making certain that the positive and negative (+ and -) battery
terminals are attached to the corresponding terminals on the plate in the battery compartment. If
an AC power failure occurs, the clock automatically switches to the battery power supply, the
clock and timer memory continue running. When the AC power resumes, the clock switches
back to AC again.
Auto-sensor LED night light
Auto-Sensor LED Night Light is a safe way to provide a light for your room, LED Bulb lasts for
thousands of hours! Press & hold the night light button (5) for 3 seconds, the LED display Auto-
sensor Indicator will light on. The night light automatically turns on in the dark and turns off in
the light.
Getting started
1. Time and calendar manual setting
A. Setting Time and Calendar – Press time set button (8) in normal mode and keep depress
over 2 seconds to enter time set mode, after enter the setting mode, press time set button
(8) to change the mode cycle as follows :
Normal →Year →Month →Day →12/24 H →Real time Hour →Real time Min →Normal
Action (during data adjustment):
-Press << / Tune - button (3) to adjust data backward.
-Press >> / Tune + button (4) to adjust data forward.
-Keep depress << or >> button for 2 seconds to enable auto forward.

UR270 / English Instruction Manual
3
B. Setting Alarm 1 and Alarm 2 – Press the alarm set button (1/2) during normal mode to
show the alarm time. Afterwards keep depress the alarm set button (1/2) over 2 seconds to
enter the alarm set mode. After enter the setting mode, press the alarm set button (1/2) to
change the mode cycle as follows:
Normal →AL 1 Hour →AL 1 Min →AL 1 weekday Alarm →AL 1 wake beep →AL 1 wake
radio →AL 1 wake radio volume →Normal.
Normal →AL 2 Hour →AL 2 Min →AL 2 weekday Alarm →AL 2 wake beep →AL 2 wake
radio →AL 2 wake radio volume →Normal.
Select alarm weekday mode as follows
1-5 : Monday to Friday
1-7 : Whole week
6-7 : Saturday & Sunday
1-1 : One day of week
Action (during data adjustment) :
-Press << / Tune - button (3) to adjust data backward.
-Press >> / Tune + button (4) to adjust data forward.
-Keep depress << or >> button for 2 seconds to enable auto forward.
Enable / disable the Alarm
Press and hold the “ALARM 1” (1) / “ALARM 2” (2) button to enable or disable the alarm. Once
the alarm is activated, the bell symbol will be appeared on the display.
Alarm duration and snooze function
Alarm Duration – Beep alarm or radio alarm will continue output for 30 minutes if no key
press, then it will stop automatically and wait for same alarm time on next day.
Action for Snooze
-During alarming, press Snooze button (9) will enable snooze function, Beep alarm or Radio
alarm will stop.
-Snooze interval is 9 minute (not include second offset)
-Snooze will continue unless press ON/OFF button (10) to alarm off of Buzzer alarm or Radio
Alarm stop automatically after 30 minutes.

UR270 / English Instruction Manual
4
Display light auto on/off function
- Press >>/TUNE+/DISPLAY LIGHT AUTO ON-OFF button (4) for
3 seconds, the LED display Indicator will light on, the LED display will turn
off after 15 seconds automatically, Press any button to maintain the LED
display for 15 seconds.
- Press >>/TUNE+/DISPLAY LIGHT AUTO ON-OFF button (4) for 3
seconds, the LED display Indicator will light off to cancel this function.
Listening to Radio
Press the ON/OFF button (10) to turn the unit on.
Use the Tune + or Tune – button to select the desired radio station. If you press and hold the
Tune + or Tune – button for one second, the release, the unit will automatically scan to the next
broadcasting station.
Press the ON/OFF button (10) to turn the radio OFF.
To set / recall the radio presets
Press the ON/OFF button (10) to turn the unit ON.
Use the Tune + or Tune - button to select the desired radio station.
Press and hold the memory / memory+ button; “P01” will blink in the display.
Use the Tune+ or Tune- button to select the desired preset station (P01-P10)
Press the memory / memory+ button again to set the preset.
Repeat steps 2 through 5 to set more presets.
The unit can preset 10 stations totally for FM.
When “P01-P10” is blinking, press the Tune+ or Tune- button to select the preset number.
When recalling preset stations, press memory / memory + button to select the preset number.
Note
-Ensure that the FM antenna is completely unrolled and extended for best FM reception.

UR270 / English Instruction Manual
5
Sleep operation
When listening to radio, press Snooze / Sleep/dimmer/DST button (9) to enter sleep mode. You
can just adjust the sleep timer from 90 mins to 15 mins by pressing the Snooze /
Sleep/dimmer/DST button (9). The unit will automatically turn off after the selected time.
Select DST (daylight saving time) mode
For countries with daylight saving time (DST).the clock radio offers you DST option to adjust
summer time.
In standby mode press and hold SNOOZE/SLEEP/DIMMER/DST button (9) for 3 seconds. The
clock advances by one hour. To exit DST mode, repeat the above operation.
Specifications
-Frequency range : 87.5 – 108 MHz
-Battery backup : 3V (CR2032 Flat Lithium battery x 1) not included
-Power supply : AC230V 50Hz
Resetting
If the system does not respond or exhibits erratic or intermittent operation, you may have
experienced an electrostatic discharge (ESD) or a power surge that triggered the internal
microcontroller to shut down automatically. If this occurs, simply disconnect the ac power cord
and remove the system backup battery, wait for at least 3 minutes and then setup the unit again
as if it is a brand new unit.
Copyright by Wörlein GmbH, D 90556 Cadolzburg – soundmaster®
Technical specifications, changes and errors are subject without any notice