Southwire MAXTerm SCU6-B User manual

Cat. No. / No de cat.
SCU6-B
18V MAXTerm™ CABLE CUTTER
COUPE-CÂBLE 18V MAXTerm™
CORTACABLES 18V MAXTerm™
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
WARNING To reduce the risk of injury, user must read and understand operator's manual.
AVERTISSEMENT An de réduire le risque de blessures, l'utilisateur doit lire et bien
comprendre le manuel.
ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.
© Southwire Company, LLC. All Rights Reserved.

2
GENERAL POWER TOOL
SAFETY WARNINGS
WARNING
Read all safety warnings, instruc-
tions, illustrations and specica-
tions provided with this power tool. Failure to follow
all instructions listed below may result in electric shock,
re and/or serious injury. Save all warnings and in-
structions for future reference. The term "power tool"
in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
•Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•Do not operate power tools in explosive atmo-
spheres, such as in the presence of ammable
liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
•Keep children and bystanders away while operat-
ing a power tool. Distractions can cause you to lose
control.
ELECTRICAL SAFETY
•Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools. Un-
modied plugs and matching outlets will reduce risk
of electric shock.
•Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
•Do not expose power tools to rain or wet condi-
tions. Water entering a power tool will increase the
risk of electric shock.
•Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk
of electric shock.
•When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
•If operating a power tool in a damp location is
unavoidable, use a ground fault circuit interrupter
(GFCI) protected supply. Use of an GFCI reduces
the risk of electric shock.
PERSONAL SAFETY
•Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use a power tool while you are tired or under the
inuence of drugs, alcohol or medication. A mo-
ment of inattention while operating power tools may
result in serious personal injury.
•Use personal protective equipment. Always wear
eye protection. Protective equipment such as a dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
•Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your nger on the
switch or energizing power tools that have the switch
on invites accidents.
•Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left at-
tached to a rotating part of the power tool may result
in personal injury.
•Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
•Dress properly. Do not wear loose clothing or
jewelry. Keep your hair and clothing away from
moving parts. Loose clothes, jewelry or long hair can
be caught in moving parts.
•If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust col-
lection can reduce dust-related hazards.
•Do not let familiarity gained from frequent use
of tools allow you to become complacent and
ignore tool safety principles. A careless action can
cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
•Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
•Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
•Disconnect the plug from the power source and/
or remove the battery pack, if detachable, from
the power tool before making any adjustments,
changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of
starting the power tool accidentally.
•Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
•Maintain power tools and accessories. Check for
misalignment or binding of moving parts, break-
age of parts and any other condition that may af-
fect the power tool’s operation. If damaged, have
the power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
•Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
•Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a hazard-
ous situation.
•Keep handles and grasping surfaces dry, clean
and free from oil and grease. Slippery handles
and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
• Recharge only with the charger specied by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of re when used
with another battery pack.
•Use power tools only with specically designated
battery packs. Use of any other battery packs may
create a risk of injury and re.
•When battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a re.
•Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact ac-

3
cidentally occurs, ush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid
ejected from the battery may cause irritation or burns.
•Do not use a battery pack or tool that is damaged
or modied. Damaged or modied batteries may
exhibit unpredictable behavior resulting in re, explo-
sion or risk of injury.
•Do not expose a battery pack or tool to re or ex-
cessive temperature. Exposure to re or temperature
above 265°F (130°C) may cause explosion.
•Follow all charging instructions and do not charge
the battery pack or tool outside the temperature
range specified in the instructions. Charging
improperly or at temperatures outside the specied
range may damage the battery and increase the risk
of re.
SERVICE
• Have your power tool serviced by a qualied repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
• Never service damaged battery packs. Service of
battery packs should only be performed by the manu-
facturer or authorized service providers.
SPECIFIC SAFETY RULES FOR
CABLE CUTTER
•Do not use tool without cutting jaws installed.
Fingers could be crushed.
•Blade is sharp. Keep hands away from all cutting
edges and moving parts. Laceration and amputation
can occur.
•To reduce the risk of injury, wear safety goggles
or glasses with side shields when operating or
servicing the tool. Material may crack or shatter.
•
WARNING
To reduce the risk of explosion,
electric shock and property
damage, do not use on live electrical lines.
Tool is NOT insulated. Contact with a live
circuit could result in severe injury or death.
Turn off power before making a cut. Never cut gas
or water lines.
•Maintain labels and nameplates. These carry im-
portant information. If unreadable or missing, contact
Southwire Tools & Assembled Products .
•
WARNING
Some dust created by power sanding,
sawing, grinding, drilling, and other
construction activities contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
•lead from lead-based paint
•crystalline silica from bricks and cement and other
masonry products, and
•arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to
lter out microscopic particles.
SYMBOLOGY
Volts
Direct Current
CUS
Underwriters Laboratories, Inc.
United States and Canada
WARNING
To reduce the risk of
explosion, electric
shock and property damage, do not
use on live electrical lines. Tool is
NOT insulated. Contact with a live
circuit could result in severe injury or
death. Turn off power before making a
cut. Never cut gas or water lines.
WARNING
Keep hands away from
all cutting edges and
moving parts. Blade is sharp. Laceration
and amputation can occur.
To reduce the risk of injury, wear safety
goggles or glasses with side shields
when operating or servicing the tool.
Read operator's manual.
FUNCTIONAL DESCRIPTION
1. Trigger
2. Locking thumb screw
3. Socket screws (5 mm)
4. Blades
5. CU/AL jaws
6. Retaining pin
7. Handle
8. Backup release valve
9. Hanger
10.LEDs
11. ACSR jaws
12.Blade retainer
6
7
8
9
5
10
4
321
12
11

4
WARNING
Blades are sharp. Keep hands away
from cutting edge. Laceration can
occur.
3. Loosen, do not remove, the socket screws using
a 5 mm hex wrench.
4. Carefully slide the blade out of the jaws, keeping
ngers away from the cutting edge.
5. Insert the new blade, keeping ngers away from
the cutting edge.
6. Securely tighten socket screws to 115 in-lbs.
NOTE: The tightening of the socket screws may
cause the jaws to close. Keep hands and ngers
out of jaws, and away from cutting edges!
7. Repeat for other blade. Always change blades as
a set.
OPERATION
WARNING
To reduce the risk of explosion,
electric shock and property
damage, do not use on live electrical lines.
Tool is NOT insulated. Contact with a live
circuit could result in severe injury or death. Turn
off power before making a cut. Never cut gas or
water lines.
Blade is sharp. Keep hands away from cutting
edges and moving parts. Avoid cutting
short pieces of material that put hands
near blades. Laceration and amputation
can occur.
Always remove battery pack before changing
or removing accessories. Only use accessories
specically recommended for this tool. Others
may be hazardous.
To reduce the risk of injury, wear safety goggles
or glasses with side shields.
Cutting
Before cutting, ensure retaining pin is properly
seated, and blade socket screws are tight.
1. Insert the workpiece squarely between the blades.
Do not attempt to make angled cuts as it will dam-
age the workpiece and blades.
2. Hold the tool rmly and support the workpiece.
Ensure the workpiece is straight and centered in
the jaws. Keep hands away from blades.
3. Pull and hold the trigger through the operation.
When the cut is complete, the blades will separate
and the tool will shut off. Release the trigger.
NOTE: Workpiece may move slightly during the cut.
4. Two LEDs will light when the trigger is pulled.
WARNING
To reduce the risk of injury, only
cut recommended materials for the
jaws (see "Specications"). Do not attempt to cut
other materials.
Cutting Tips
• Cut farther in from the end of the material to avoid
crooked cuts.
• Do not attempt angled cuts. It will damage the
blades. Hold the material squarely between the
blades.
• Cut clean material to extend the blade life. Wipe dirt
and debris from material and blades before begin-
ning the cut.
• Do not cut ACSR materials with CU/AL jaws. Do
not cut CU/AL materials with ACSR jaws. It could
damage the blades, jaws, and tool.
• When use the ACSR jaws, ensure the blade retainer
is installed.
SPECIFICATIONS
Cat. No...................................................... SCU6-B
Volts.............................................................. 18 DC
Battery Type ...........................MILWAUKEE M18™
Charger Type..........................MILWAUKEE M18™
Jaw Type............................................. ACSR Jaws
(STJ6-ACSR)
Maximum Capacity....ACSR: 477 MCM Hen ACSR
Guy Wire: 3/8" Non-EHS
Rebar: 3/8"
Ground Rod: 3/8"
Replacement Blades ............ Cat. No. STJB-ACSR
Jaw Type.............................................CU/AL Jaws
(Cat. No. STJ6-CUAL)
Maximum Capacity......... Copper Cable - 750 mcm
Aluminum Cable - 1000 mcm *
Replacement Blades .............Cat. No. STJB-CUAL
*CU/AL Jaws will cut any aluminum cable with a
diameter less than 1.225"
ASSEMBLY
WARNING
Recharge only with the charger
specied for the battery. For spe-
cic charging instructions, read the operator’s
manual supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons
and pull the battery pack away from the tool.
To insert the battery, slide the pack into the body
of the tool. Make sure it latches securely into place.
WARNING
Always remove battery pack before
changing or removing accesso-
ries. Only use accessories specically recom-
mended for this tool. Others may be hazardous.
Blades are sharp. Keep hands away from cutting
edge. Laceration can occur.
Inserting/Removing the Cutting Jaws
Use only Southwire cutting jaws. Do not use with
other jaw types. Other jaw types can cause damage
to the tool.
1. Remove the battery pack.
2. Remove the locking thumb screw (when used)
from the back of the retaining pin.
3. Push in, then rotate the retaining pin counterclock-
wise 90° . The pin will pop out.
4. Insert the cutting jaws. Line up the center hole with
the retaining pin.
5. Push in the retaining pin, then rotate clockwise
90° .
6. Insert and hand tighten the locking thumb screw.
NOTE: Use the locking thumb screw to prevent the
retaining pin from being unintentionally loosened.
A loose retaining pin may damage the tool.
7. Rotate the jaws to the desired angle.
CAUTION
To avoid damage to the tool, do not
operate the tool without the retain-
ing pin fully inserted and locked into position.
Damage to the cylinder may occur.
Changing the Blades
Replace the blades when they become dull, rounded,
chipped, or damaged.Always replace blades as a set.
Use only Southwire blades and cutting jaws. Refer
to Specications for replacement blade numbers.
1. Remove the battery pack.
2. Remove cutting jaws from tool.

5
Backup Release Valve
If the jaws need to be opened without completing the
cycle, press and hold the backup release valve. Hold
tool securely until the cylinder retracts fully.
Jammed Blades
Dirt and debris can cause the blades to become
jammed together after a cut. If the tool shuts off and
the blades are still closed:
1. Press and hold the backup release valve to ensure
the tool has reset.
2. Remove the battery pack.
3. Remove the jaws from the tool.
4. Use a soft mallet to tap the rear of the jaws to
release.
5. Clean any dirt and debris from the blades before
starting another cut.
MAINTENANCE
WARNING
To reduce the risk of injury, always
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact
Southwire Tools & Assembled Products for ALL
repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to Southwire Tools & Assembled Products for repair.
After six months to one year, depending on use, re-
turn the tool, battery pack and charger to Southwire
Tools & Assembled Products for inspection.
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack, to
Southwire Tools & Assembled Products for repairs.
Jaws and Blades
Inspect jaws for cracks or damage. Do not use dam-
aged jaws. Replace the blades when they become
dull, rounded, chipped, or damaged.
Hydraulic Fluid
To extend the life of the tool, return the tool to
Southwire Tools &Assembled Products for hydraulic
uid replacement after 20,000 cuts or 2 years of use.
WARNING
To reduce the risk of personal in-
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to ow inside them.
Cleaning
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these harmful agents
include gasoline, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia and
household detergents containing ammonia. Never
use ammable or combustible solvents around tools.
Repairs
For repairs, return the tool, battery pack and charger
to Southwire Tools & Assembled Products.
ACCESSORIES
WARNING
Use only recommended accesso-
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.southwiretools.com.
SERVICE
For all warranty, customer service, and product
return authorizations and inquiries, please contact
Southwire Tools & Assembled Products at:
Southwire Tools & Assembled Products
840 Old Bremen Road
Carrollton, GA 30117
Phone Number: 1.855.SW.Tools
www.southwiretools.com
WARRANTY
Every Southwire power tool is warranted to the original purchaser only
to be free from defects in material and workmanship. Subject to certain
exceptions, Southwire will repair or replace any part of the electric
power tool which, after examination, is determined by Southwire to
be defective in material or workmanship for a period of ve (5) years*
after the date of purchase unless otherwise noted.
Return of the power tool to Southwire or a Southwire factory service
center freight prepaid and insured, is required. A copy of the proof of
purchase should be included with the return product. This warranty
does not apply to damage that Southwire determines to be from re-
pairs made or attempted by anyone other than Southwire authorized
personnel, or from misuse, alterations, abuse, normal wear and tear,
lack of maintenance, or accidents.
All Milwaukee batteries and chargers are covered under separate and
distinct warranties available for those items. For more information,
visit www.milwaukeetool.com/service/milwaukee-warranty/cordless-
battery-pack.
Warranty Registration is not necessary to obtain applicable warranty on
a Southwire power tool product. The manufacturing date of the product
will be used to determine the warranty period if no proof of purchase
is provided at the time warranty service is requested.
THE REMEDIES SET FORTH ABOVE ARE YOUR EXCLUSIVE REM-
EDIES RELATING TO YOUR WARRANTED SOUTHWIRE ELECTRIC
POWER TOOL. IN NO EVENT SHALL SOUTHWIRE BE LIABLE FOR
ANY INCIDENTAL, SPECIAL, CONSEQUENTIAL, OR EXPENSES,
LOSSES OR DELAYS ALLEGED TO BE AS A CONSEQUENCE OF
ANY DAMAGE TO, FAILURE OF, OR DEFECT IN ANY PRODUCT
INCLUDING, BUT NOT LIMITED TO, ANY CLAIMS FOR LOSS OF
PROFITS. SOME STATES DO NOT ALLOW THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU. THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL
OTHER EXPRESS WARRANTIES, WHETHER WRITTEN OR ORAL.
TO THE EXTENT PERMITTED BY LAW, SOUTHWIRE DISCLAIMS
ALL IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS
FOR A PARTICULAR USE OR PURPOSE; TO THE EXTENT SUCH
DISCLAIMER IS NOT PERMITTED BY LAW; SUCH IMPLIED WAR-
RANTIES ARE LIMITED TO THE DURATION OF THE APPLICABLE
EXPRESS WARRANTY AS DESCRIBED ABOVE. SOME STATES
DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO
YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS,
AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
Model:_______________________________
Date of Purchase: _____________________
Distributor:___________________________