Spa-Quip SP400P User manual

AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
HEATHEATHEATHEAT PUMP AUTO AUTO AIR PUMP AUTO AUTO AIR
ONON
User’s GuideUser’s Guide
Models Covered ByThis User’s Guide :
SP601-15
SP601-15T
SP601AU-15
SP601AU-15T
SP601-20
SP601-20T
SP601AU-20
SP601AU-20T
SP601-30
SP601-30T
SP601AU-30
SP601AU-30T
SP400P
SP400PAU-10
SP400PAU-15

Contents
1 Touch Pads......................................................................................................................................... Pg 1
2 Temperature Control............................................................................................................................ Pg 2
2.1 - Adjusting Set Temperature............................................................................................... Pg 2
2.2 - Non Default Display Value............................................................................................... Pg 2
2.3 - Heating Mode Selection(24hr circulation pump not fitted)............................................... Pg 2
3 Pump Operation.................................................................................................................................. Pg 3
3.1 - Pump 1 (Single speed pump, no 24hr circulation pump fitted)........................................ Pg 3
3.2 - Pump 1 (Single speed pump, 24hr circulation pump fitted)............................................. Pg 3
3.3 - Pump 1 (Two speed pump,no 24hr circulation pump fitted)............................................ Pg 4
3.4 - Pump 1 (Two speed pump, 24hr circulation pump fitted)................................................ Pg 4
4 Auxiliary/Air Button.............................................................................................................................. Pg 5
4.1 - Adjustable Speed Mode(SPVSB only)............................................................................. Pg 5
5 Light Operation.................................................................................................................................... Pg 6
5.1 - Adjustable Colour Mode(SPVCL only............................................................................... Pg 6
5.2 - IndicatorLlight................................................................................................................... Pg 6
6 Auto Sanitisation.................................................................................................................................. Pg 7
6.1 - No 24hr Circulation Pump Fitted...................................................................................... Pg 7
6.1.1 - Adjusting Minimum Filtration........................................................................... Pg 7
6.1.2 - Clean Up Cycle.............................................................................................. Pg 7
6.2 - 24hr Circulation Pump Fitted........................................................................................... Pg 7
6.3 - My Spa Is Too Hot In Summer......................................................................................... Pg 7
7 Sleep Timer......................................................................................................................................... Pg 8
7.1 - To Set Current Time And Day........................................................................................... Pg 8
7.2 - To Set Programs...............................................................................................................Pg 8
8 Self Diagnostic Error Codes................................................................................................................ Pg 9
Section

HEATHEAT PUMP AUTO AIR PUMP AUTO AIR
ONON
AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
The green Pump indicator light will appear on the touch pad whenever the pump is running, in both
auto and manual use mode. If this light is flashing, the spa is in Sleep Mode.
Pump LED
The red Heater indicator light will appear on the touchpad whenever the heater element is on, in
both auto and manual use mode. For safety the heater is always automatically controlled.
Usually switching on the air blower accessory will cause the heater to switch off (loadshedding).
This is in order to keep the total power load to a safe level. If this light is flashing the system has an
error
Heat LED
(see section 8).
H20 LED (24hr circulation pump fitted)
The yellow H20 light indicates if water is present in the heater. If no water is detected then the LED
will flash and the unit will not operate except to run the circulation pump to try to get water to the
heater. If no water reaches the heater for one minute then an H20 error will occur. If this happens
then pushing the pump button will run the circulation pump for another minute.
Page 1
Congratulations on choosing the latest Spa Power control system. This
controller makes use of the latest technology, including innovative optical and
digital sensor designs. The greater variety of optional accessories, user-
friendly touchpad and reliable components provide you with the most
sophisticated controller in its class.
Heat LED
Pump LED
Auto/H20 LED
Aux/Air LED
Aux/Air/Pump Button
Up Button
Down Button
Heat LED
Pump LED
Auto/H20 LED
Aux/Air LED
Pump Button
Pump Button
Aux/Air/Pump Button
Up Button
Down Button
37.0
1 Touch Pads
Auto LED (No 24hr circulation pump fitted)
The yellow Auto indicator light will appear on the touch pad whenever the system is in full
automatic control mode. In this mode the system automatically activates the pump and heater to
filter the water and maintain the set water temperature. If this light is flashing the water sensor is
not detecting any water.
Aux/Air LED
The Aux/Air indicator LED will appear on the touchpad whenever the Aux/Air button is pushed
and conversly will disapear when the button is pushed again. Note: If the spa does not have a
load connected to the controller the LED will still operate as described above.
37.0

HEATHEATHEATHEAT PUMP PUMP AUTOAUTO AIR AIR PUMP PUMP AUTOAUTO AIR AIR
ONON
AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
HEATHEATHEATHEAT PUMP PUMP AUTOAUTO AIR AIR PUMP PUMP AUTOAUTO AIR AIR
ONON
AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
HEATHEATHEATHEAT PUMP PUMP AUTOAUTO AIR AIR PUMP PUMP AUTOAUTO AIR AIR
ONON
AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
Page 2
The Spa Power controller automatically controls the pump and heater to filter the water and maintain it at the
desired temperature set by the user (see below).The user can leave the system to look after the spa and know it will
be at the correct temperature whenever he or she wants to use it.
2 Temperature Control
2.1 Adjusting Set Temperature
UP Increase the set temperature by 0.5 C per beep (Max = 41.5 C)
oo
DOWN Decrease the set temperature by 0.5 C per beep (Min = 10.0 C)
oo
The Spa Power controller gives the user direct control of the pool temperature from the poolside control panel.
Holding down the Up or Down button will adjust the temperature set point as shown on the digital readout. There is
a slight delay before the buttons operate to reduce the risk of accidental adjustment. The pool temperature will be
maintained very close to the set temperature.
The display normally shows the temperature set point, unless the optional in pool temperature sensor is fitted in
which case the sensed water temperature is displayed. In either case the temperature set point will be displayed
while being adjusted as described above.
Default Display 37.0
2.2 Non-Default Display Value
The non-default display value (either sensed water
temperature or temperature set point) can be checked if
necessary by pressing the Up & Down buttons simultaneously.
Press both buttons
simultaneously
In addition to the temperature setting the user can select the preferred heating mode. The two available heating
modes are...
1/ Demand Heating (displayed as Ht.d).This is the default setting in which the pump and heater will come on
automatically whenever the temperature drops slightly below the set point.
2/ Filtration Only Heating (displayed as Ht.F) .In this mode the pump and heater will come on automatically no more
than once per hour to filter and heat the water. This mode is provided as an option for those who prefer to limit the
natural cycling of the system.
To select the heating mode first press the Pump and Down buttons simultaneously to display the current heating
mode, then press and hold the Up or Down buttons to change modes.
2.3 Heating Mode Selection (24hr circ pump not fitted)
Press both buttons
simultaneously
Press Up or Down
buttons to toggle
between heating
modes.
37.0
37.0

Push 3 (Auto Mode)
Push 1 (Pump on)
Push 2 (Pump off)
3 Pump Operation
Page 3
There are four possible variations of pump 1 that may have been fitted to your spa, this user guide covers all
variations of pump 1 that could have been fitted. Please read sections 3.1 through to 3.4 then follow the section
which matches your spa operation.
Note: Even if a 24hr circulation pump is fitted there is no button to control it. The 24hr circulation pump operation is
completely automatic, It only turns off in sleep mode (if optional time clock is fitted) or in an error condition.
Push 1 (Manual Mode)
Push 2 (Standby Mode)
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
Pump 1 is controlled by just one touch pad button pushing the pump button three times cycles its operation through
three modes Automatic, Manual and Standby. When the spa is running in automatic mode, pressing the pump
button will deactivate auto mode and set the pump running in Manual Mode. The auto LED is orange when auto
mode is enabled and off when in Manual Mode. When the pump is in standby mode all indicator LED's are off.
Pushing the pump button two times turns the pump on and then off. The pump LED is green when the pump is running and off
when the pump is off.
Notes:
1) If Pump 1 is left on, it will automatically switch off after 20 minutes.
2) There is no direct user control over the heater. The heater may come on automatically whenever the 24hr
circulation pump is on.
3) If the heater element is on, running the pump may cause the heater to load shed and switch off. If this occurs the
heater will come back on approximately 5 seconds after the pump is deselected.
Notes:
1) If Pump 1 is left in ”Manual or “Standby” modes it will automatically revert to “Auto” mode after 90 minutes.
2) There is no direct user control over the heater. The heater may come on automatically whenever Pump 1 is on.
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP
H20
AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP
H20
AIR
3.2 Pump 1 (Single speed pump, 24hr circulation pump fitted)
3.1 Pump 1 (Single speed pump, no 24hr circulation pump fitted)

3.3 Pump 1 (Two speed, no 24HR circulation pump fitted)
Page 4
Push 1 (Manual Low Speed)
Push 2 (Manual High Speed)
Push 3 (Standby Mode)
Push 4 (Auto mode)
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR
Push 1 (Low Speed)
Push 2 (High Speed)
Push 2 (Pump off)
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP
H20
AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP
H20
AIR
HEATHEAT PUMP AUTO AIR PUMP AUTO AIR PUMP AUTO AIR PUMP
H20
AIR
Pump 1 is controlled by just one touch pad button pushing the pump button 4 times cycles its operation through 4
modes Automatic, Manual Low Speed, Manual High Speed and Standby. When the spa is running in automatic
mode, pressing the pump 1 button will deactivate auto mode and set the pump running in Manual low speed. The
auto LED is orange when auto mode is enabled and off when in manual low speed or manual high speed. When
the pump is in standby mode all indicator LED's are off.
Notes:
1) If Pump 1 is left in ”Manual or “Standby” modes, it will automatically revert to “Auto” mode after 90 minutes.
2) There is no direct user control over the heater. The heater may come on automatically whenever Pump 1 is on.
3) If the heater element is on, running the pump in high speed may cause the heater to load shed and switch off.
Pushing the pump button three times cycles the pump through its two speeds then off. The pump LED is green
when the pump is running in low or high speed and off when pump is off.
Notes:
1) If Pump 1 is left on, it will automatically switch off after 20 minutes.
2) There is no direct user control over the heater. The heater may come on automatically whenever the 24hr
circulation pump is on.
3) If the heater element is on, running the pump in high speed may cause the heater to load shed and switch
off. If this occurs the heater will come back on approximately 5 seconds after the pump is deselected.
3.4 Pump 1 (Two speed, 24HR circulation pump fitted)

Page 5
TheAir Button controls an auxiliary air blower. It is used to turn the blower on and off, and select different
operating modes if a Spa Power Variable-Speed Blower (SPVSB) has been fitted. 2 pushes (STD) or 4
pushes (SPVSB) of the air button cycles the blower as follows:
Note: In some spas an additional jet pump or pool light etc may be fitted instead of a standard air blower.
4 Auxiliary Air Button
Standard Air Blower (STD)
4.1 Adjustable Speed Mode (SPVSB only)
If a Spa Power Variable-Speed Blower is fitted, the spa user has the ability to adjust the blower speed to
any desired setting. The Up and Down buttons are used to set the desired blower speed. Note: If the
blower is in Full Speed or Oscillating modes then pushing the Up or Down button will put it into
Adjustable Speed mode and then adjust the speed.
AIR Light turns
to orange
Step 1) Press Air Button to set Adjustable Speed Mode
Step 2) Press Up to speed of blower
Step 3) Press Down to speed of blower
twice
increase
decrease
Push 1 - Blower ON
Push 2 - Blower OFF
Push 1 - Blower ON (Full Speed)
Push 2 - Blower ADJUSTABLE (Adjustable Speed)
Push 3 - Blower OSCILLATING (Oscillating Speed)
Push 4 - Blower OFF (Default State)
AIR Red
Light
AIR Orange
Light
AIR Green
Light
AIR No
Light
Spa Power Variable-Speed Blower (SPVSB) (if fitted)
Note: If left on, this accessory will automatically switch off after 20 minutes. If the heater element is on, switching on
this accessory may cause the heater to loadshed and switch off. This is to keep the total power load to a safe level.

Page 6
When the light is on, short presses of the Down button will put the light into adjustable colour mode
and then sequentially select through all the available colours. The last colour set in this mode will be
remembered the next time the light is used.
5 Light Operation
The multi-function Light Button is used to turn the light on and off (SPCL) and select through the
different operating modes of the Spa Power Variable Colour Light. Two short presses of the button will turn
the Spa Power Coloured Light on and off or five short presses of the button will cycle the Spa Power
Variable Coloured Light as follows:
Push 1 - Light ON
Push 2 - Light ADJUST
Push 3 - Light CYCLE SLOW
Push 4 - Light CYCLE FAST
Push 5 - Light OFF
(SPCL - On) (SPVCL Colour - White)
(SPCL - Off) (SPVCL Adjustable Colour Mode)
(SPVCL Cycle through colours - slowly)
(SPVCL Cycle through colours - quickly)
(Default State)
Light Button
5.2 Indicator Light
ON
A small red dot in the bottom corner of the digital readout indicates when the
light is turned on. If left on the light will automatically switch off after 30
minutes.
Note: This is a multi-function button which performs the following -
1) Short presses of this button activate the light functions as detailed above.
2) Holding this button will begin to increase the set temperature of the spa.
3) When a Spa Power Variable Speed Blower is fitted and is turned on this button increases the blower speed.
5.1 Adjustable Colour Mode (SPVCL only)
Your spa may have been fitted with either of two different LED lights; a Spa Power Coloured Light
(SPCL) or a Spa power Variable Coloured Light (SPVCL). The Spa Power Coloured Light is a single
coloured light that is either on or off. The Spa Power Variable Coloured light is a light that has the
ability to change between 12 different colours and white (see below for user instructions).

HEATHEAT PUMP PUMP AUTO AIR AIR PUMPPUMP AUTO AIR AIR
ONON
AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
Page 7
During warm periods of the year there may be times when the actual water temperature exceeds the desired temperature set by
the user. E.g. If the spa is set to heat to 35 C , but the actual water temperature is hotter than 35 C. Please consider this - In the
winter your spa gets cold because the air temperature is cold. To combat this we heat the water and keep the spa covered when not
in use. If the spa is turned off and the ambient temperature is 15 C, eventually the spa water will lose heat until it too is 15 C. In the
summer the same applies but in reverse - you can turn the heater down, even turn the pump off, but if the ambient daytime
temperature is 35 C - 42 C then the spa water will also remain at that temperature.
Manufacturers make no attempt to supply a system that cools water. The quickest way to combat the problem is to change the
water, but even this new water will eventually heat up to the air temperature. Turn the set temperature down so the heater does not
come on. Reduce the minimum filtration time (non circ pump models only) so the pump runs less. The less the pump runs the more
the water will cool. If the nighttime temperature is low, leave the cover off the spa to let heat escape, but put it back on during the day
to keep heat out. If the optional timeclock is fitted increase the sleep time period otherwise turn the spa off overnight. Also make
sure the spa is shaded from direct sunlight.
o o
o o
oo
The Spa Power controller automatically maintains the filtration/sanitising of the spa pool water. The minimum
amount of filtration time is programmable by the user and can be adjusted between 0 and 15 minutes per hour (0 to 6
hours per day). In order to maintain correct filtration of the pool water, the controller monitors the time for which the
pump runs in normal pool operation. If the pump has only run for a short time, the system will automatically run the
pump for an additional period every hour to reach the minimum filtration time set by the user.
6 Auto Sanitising (Filtration)
6.1.1 Adjusting Minimum Filtration Time (No 24hr circulation pump fitted))
First push the Down andAir/Aux buttons together to display the filtration time setting on the digital
readout
If desired, a clean up cycle can be initiated to filter the water after the spa pool has been used. This is done by simply
pushing the Pump Button to leave auto mode and switch on the pump. This will circulate the water through
the filter for 90 minutes.After 90 minutes the system will return to auto mode and maintain the temperature ready for
the next time the spa pool is used.
6.1.2 Clean Up Cycle
6.3 My Spa Is Too Hot In Summer!
The default setting is 10 minutes per hour (= 4 hours per day). Holding down the Up Button or Down
Button will adjust the filtration time setting between 0 and 15 minutes per hour. (= 0 to 6 hrs per day).
Press both buttons
simultaneously
Press both buttons
simultaneously
6.1 No 24hr Circulation Pump Fitted
6.2 24hr Circulation Pump Fitted
The Spa Power controller continuously filters the spa pool to ensure the water is clean and crystal clear
for each and every spa use. A near silent energy efficient circulation pump constantly passes water
through the filter and since the circulation pump runs all the time (except for when the time clock has been
set to sleep or in an error condition) and the heater is controlled automatically there is no need for any
user controls for these features. With a 24hr circulation pump fitted there is no need to program any
filtration cycles, and the noise of a large jet pump running during filtration has been removed.

Page 8
If the optional time clock has been fitted, sleep mode is used to disable
automatic temperature maintenance and filtration in order to silence the spa
pool during your hours of sleep. The sleep time setting is done using the digital
time clock on the front of the control box (See below for setting instructions). If
the spa is in use it will not enter sleep mode until 30 minutes after the last
manual button push, even if the clock is calling for sleep mode. The spa can
still be used manually within sleep mode times as normal. On wake up from
sleep the system will run the blower for 15 seconds to purge the blower
plumbing. This prevents any stagnant water from collecting in the pipes if the
pool is not used for an extended period.
7.1 To Set Current Time and Day
1. Press the button before use. NOTE: This is optional. It will clear the current time and program settings.
2. Hold down the button and press the button until the correct day is selected. Release both buttons.
3. Hold down the button and press the button until the correct hour is set. Release both buttons.
4. Hold down the button and press the button until the correct minute is set. Release both buttons.
5. After setting the weekday and time, the seconds will reset automatically and the clock will begin keeping time.
RESET
CLOCK DAY
CLOCK HOUR
CLOCK MIN
7 Sleep Timer (Optional Timeclock)
7.2 To Set Programs
1. Press the button. "1ON" will appear at the left side of the display. This is the start time of the first programmed sleep
block (the time you want the spa to enter the sleep mode).
2. Press the button to select the days on which this sleep program will operate. There are 15 settings to choose from.
3. Press the button to set the hour of the desired time to enter sleep mode.
4. Press the button to set the minutes of the desired time to enter sleep mode.
5. Now the start time has been set, press the button again. "1OFF" will appear on the display.This is the end time of the first
programmed sleep block (the time you want the spa to resume normal operation).
6. Repeat the same procedure (2 to 4 above) until the "1OFF" time is set.(
7. Your timer gives you up to 8 different programmable periods. You can use all 8 settings , or as few as you like.
8. To Review your set programs press the button and keep pressing it to advance through each setting.
TIMER
DAY
HOUR
MIN
TIMER
TIMER
Be careful to set the same days as used in the "1ON" time).
IMPORTANT NOTE: The "MANUAL" button on the clock can be used to override the programmed sleep
settings. It is very important to ensure that the clock is set to "AUTO" so that the programmed times can
operate. If the clock is manually set to ON then the pool will stay in sleep mode and THE WATER WILL GO
COLD. If it is left in "OFF" then the pool will not enter the sleep mode. The clock does not return to "AUTO"
by itself.
NOTE: If the “MANUAL” button on the clock is used the spa will not return to the programmed settings until
the next programmed time after being returned toAuto.
MANUAL
D
AY
C
L
O
C
K
T
I
M
E
R
H
O
U
R
M
I
N
P
ON
9:3139
ON AUTO OFF
MON
Safety Notes
Before using ensure that the spa pool has been connected to a suitable weather protected outlet socket, equipped with a double
pole isolating switch, which is of the correct rating and complies with the local wiring regulations.
When installing refer to your local wiring code. In particular refer to ECP 2 & ECP 25 (AS / NZ) and EN 60364-4-1 & EN 60364-7-1
(EU). The system must be installed in such a way that live parts are not accessible by a person in the pool. If a supply cord is not
fitted the system must be permanently connected to fixed wiring through a 30mAor less RCD.
This appliance is not intended for use by young children or infirm persons without supervision. Young children should be supervised
to ensure they do not play with the appliance.

HEATHEATHEATHEAT PUMP PUMP AUTOAUTO AIR AIR PUMP PUMP AUTOAUTO AIR AIR
ONON
AUTO
PUMP
HEATER
AIR
ON
<TEMP SET>
HOLD BUTTON
TO ADJUST
PRESS BOTH
TO READ ACTUAL
Page 9
8 Self-Diagnostic Error Codes
The Spa Power controller has extensive self diagnostic capabilities. In the event of a problem it will indicate an
error number according to the nature of the problem. The error numbers and their meanings are listed below.
Note: When in an error state the alarm can be muted by pushing theAIR/AUX button.
Error 1 (H20)
With any Error 3-8, spa operation will stop and not continue until the controller is reset. The controller can
only be reset by pushing the UP, DOWN and PUMP buttons simultaneously.
The controller will remain in an error condition even when reset at mains power, controller will only continue
normal operation after the UP, DOWN and PUMP buttons are pushed simultaneously (see below).
Error 3
Error 4
Error 5
Error 6
Error 7
Error 8
- Prime Failed
This is not necessarily a problem with the controller itself, but indicates that no water is being detected in the heater housing. Prime failed
is a special case in that it can be recovered from by pushing a button. A push of the pump button will run the pump for 10 seconds to try to
get water to the heater. If successful normal operation will resume. If unsuccessful, Error 1 (H20) will be indicated on the display again.
- Stuck Button
This error indicates that one of the buttons in the touchpad is stuck or has been held down for more than one minute. This may be caused
by the pool cover pressing on the touchpad or by water getting into the touchpad or by damage to the touchpad or its cable. Try to reset
the spa. If there is still a problem then contact your spa pool supplier.
- No Water Sensor
This error indicates a problem with the optical water sensor in the heater. The problem may by caused by the sensor being disconnected
or by damage to the sensor. Try to reset the spa. If there is still a problem then contact your spa pool supplier.
- Overtemperature
This error indicates that the digital temperature sensor in the heater or pool has detected a temperature of 45 C or more. This may not be a
problem with the controller, it may be caused by excessive pump use in hot weather, or pump failure. Turn off the spa and allow time for the
water to cool. If there is still a problem then contact your spa pool supplier.
- Thermal Cut Out Tripped
This error indicates that the safety electromechanical over temperature cut out on the heater has operated. This is not necessarily a
problem with the controller. It may have occurred from an air lock around the element, high temperatures during shipping, or failure of the
pump. This automatic cut out will only reset once the element has cooled below about 38 C. The unit must then be reset before it will
resume operation. Manually push the UP, DOWN and PUMP buttons simultaneously.
- Stuck Relay
This error indicates a problem with the heater control circuitry inside the unit. Contact your spa pool supplier.
- No Temperature Data
This error indicates a problem with the digital temperature sensor in the heater or pool wall or that both the in heater and in pool sensors
are connected. Check that only one sensor is connected and that it has not become disconnected or damaged. Try to reset the spa. If
there is still a problem then contact your spa pool supplier.
o
o
Up Button
Down Button
Pump Button
Pump Button
Up Button
Down Button
E.6
E.6

Spa-Quip Ltd
Ph: 64 9 415 8622
Spa-Power Equipment
www.spa-quip.co.nz
[email protected]
2 Rothwell Ave
North Harbour Industrial Park, Auckland NZ
Fax: [phone]
Spa-Quip Ltd
Ph: 1300 797 828
Spa-Power Equipment
www.spa-quip.com.au
[email protected]
6 Lakeview Drive
Fax: [phone]
Scoresby, VIC 3179 Australia
SP601/400P User’s Guide .pdf
Booklet Part Number Q916321
3rd October 2006
N376
Pb
RoHS
COMPLIANT