Space 75-37A773 User manual

2
1
FEATURE
• PNEUMATIC SEAT HEIGHT ADJUSTMENT
To raise seat remove pressure from seat and lift lever (1) up.
To lower seat height sit on chair and lift lever (1) up.
• LOCKING MID-PIVOT KNEE TILT ADJUSTMENT
Pull lever (3) out for free float, To lock return chair to the upright
position and push lever (3) in.
• TILT TENSION ADJUSTMENT
For individual comfort, this chair has been equipped with an
adjustment that will allow the user to change the tension of the
tilting feature. Turn knob (2) clockwise to increase tension and
counter-clockwise to decrease or ease the tension.
NOTE: Be careful not to loosen tilt adjustment knob completely.
• ARM HEIGHT ADJUSTMENT
To adjust arm height, push button (4) in to allow the arms
to move up or down freely. Release the button (4) once the
desired height is reached.
• ARM WIDTH ADJUSTMENT
To adjust width, push lever (5) down slide arm to
desired postion then pull lever (5) up to lock arm
into postion.
75-37A773 / 75-47A773 MANAGERS CHAIR
OPERATING INSTRUCTIONS
WARNING
1. Use this product only one person at a time.
2. Do not use this chair unless all bolts screws and
knobs are securely tightened.
3. Check that all bolts screws and knobs are tight
every three months or as needed.
4. Do not overturn back tilt knob when decreasing
tension.
5. Dispose of packing material properly. Do not use
plastic cover as head covering. It may cause
suffocation.
6. Do not use chair as a stepladder.
7. Use this chair for its intended purpose only.
8. Use mild detergent only for cleaning.
LIMITED WARRANTY
SPACE®chairs are warranted* from the date of purchase against failure due to material and workmanship as follows:
 •Lifetimeoncomponentpartsincludingpneumaticcylinder,controlmechanism,baseandcasters.
 •3Yearsonupholsteryfabricandfoamagainstwearanddeterioration.
*All warranties are limited to the original purchaser for normal commercial usage defined as a standard forty hour work week by persons
weighing 250 lbs. or less. This warranty will not cover labor, freight or damage from misuse, abuse, negligence, alteration, accident, vandalism,
rusting, acts of nature or any other event beyond the control of Office Star Products. The warranty does not cover cosmetic damage that may
result from normal use. Liability for incidental or consequential damages is excluded.The user assumes all risk of injury resulting from use of
this product. When usage is more than 40 hours per week, a five year warranty on all parts applies. Fabric is warranted for one year. This warranty
gives you specific legal rights, and you may also have other rights which vary from state to state.
To make a warranty claim, contact Parts Department via e-mail parts@officestar.net, by Fax [phone], or toll free parts
number 1-800-950-7262, Monday through Friday 8:00 a.m. - 5:00 p.m. Pacic Time. Provide model number and description of the
problem and obtain conrmation number. At it’s option Ofce Star Products will:
(a) Supply compatible components of current manufacture.
(b) Repair the customer’s component.
It is the customer’s responsibility to prepay freight on any components returned to the factory. Return freight on components
covered by warranty will be paid by Ofce Star Products.
4
5
3

Phillips Screwdriver also needed for
assembly (not provided)
PART QTY
1. Base ....................1
2. Casters ..................5
3. Pneumatic Cylinder .........1
4. Mechanism ...............1
5. Seat Cushion ..............1
6. Back Assembly . . . . . . . . . . . . 1
7. Arms Left (7L) Right (7R). . . . . 2
8. Phillips Screws . . . . . . . . . . . . 8
9. Small Allen Screws . . . . . . . . . 4
10. Large Allen Screws . . . . . . . . 4
11. Back Support (Pre-Installed) . 1
12. Allen Wrench .............1
1
Remove all parts from carton, separate by part numbers indicated on parts list, and verify part quantities.
STEP 1 Insert five Casters (2) into Base (1), push hard until you feel or hear the Caster (2) snap into place.
STEP 2 AligntheholesintheArms(7L&7R)withtheholesintheSeatCushion(5),attachArms(7L&7R)toSeatCushion(5)usingfour
Phillips Screws(8)for each arm. FULLY TIGHTEN ALL SCREWS USING PHILLIPS HEAD SCREWDRIVER.
STEP 3AttachMechanism(4)toSeatCushion(5)withthearrowtowardsthefrontofthechair,usingfourLargeAllenScrews(10),
TIGHTEN ALL FOUR SCREWS COMPLETELY.
STEP 4 AttachBackSupport(11)torearofMechanism(4)usingfourSmallAllenScrews (9),
FULLY TIGHTEN ALL SCREWS USING ALLEN WRENCH (12).
STEP 5 Insert Pneumatic Cylinder (3) into Base (1), Place the assembled seat on top of Pneumatic Cylinder (3) and
apply downward pressure.
ATTENTION: MAKE SURE ALL SCREWS ARE FULLY TIGHTENED BEFORE USING CHAIR.
75-37A773 / 75-47A773 MANAGERS CHAIR
ASSEMBLY INSTRUCTIONS
©OfceStarProductsJune2007
STEP 1 STEP 2 STEP 3
STEP 4
STEP 5
2
3
1
12
9
11
7R
8
812
10
4
4
5
5
7L
X5
X4
X4
X4
X4
6
6