Space Bad Boy Fox User manual

This manual contains important information relating to the installation, and operation of this pump. Please ensure this
manual is left with the pump operator for future reference.
Model
–
Fox
Single Speed Spa Pump
1
year warranty
This manual contains important information relating to the installation, and operation of this pump. Please ensure this
manual is left with the pump operator for future reference.
Bad Boy
Spa & Swimming Pool
Pumps
This manual contains important information relating to the installation, and operation of this pump. Please ensure this

IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety
including the following: READ AND FOLLOW ALL
1.
WARNING
To
reduce the risk of injury. Do not permit children to use this product
times.
2.
WARNING
Risk of Electrical Shock. Connected only to grounding type receptacle protected by a ground fault circu
interrupter (GFCI).
3.
Contact a qualified electrician if you cannot verify that the receptacle is protected by GFCI.
4.
CAUTION
Do not bury cord. Locate cord to minimise damage from other
5.
CAUTION
R
unning parts
can cause injury. D
system is ready for operation.
6.
WARNING
To
reduce the risk of electrical shock, replace damaged cord immediately.
7.
WARNING
To
reduce
the
risk
of
electrical
located
outlet.
8.
CAUTION
This
pump
is
for
use
in
fixed
9.
Do
not
install
within
an
outer
enclosure
10.
FOR
INDOOR
USE
ONLY.
11.
SAVE
THESE
INSTRUCTIONS.
12.
Household use
only.
13.
Connection
must
be
incorporated
into
14.
In
order
to
avoid
a
hazard
due
to
inadvertent
external switching device, such as a timer,
Do not dispose of electrical appliances as unsorted municipal waste, use
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
groundwater and get into the fo
GENERAL
-
These instructions are for
the
correct installation, and optimum performance of Bad Boy Spa
so they should be read carefully.
-
These are single
-
stage centrifugal pumps
equipped with a total emptying system to prevent the discharge of residual water in each stop cycle
-
V/Hz 240/50: See pump nameplate.
-
These units are designed to operate with cle
-
Storage temperature:
-
10
°
C ~ +50
°
C. Relative Air Humidity: 95% Max.
-
Built of top quality materials; they are subjected to strict hydraulic and
-
Correct installat
ion is ensured by following these instructions and those of the wiring diagram; otherwise, over loads may be
produced in the motor. We decline responsibility for any damage caused by not following these instructions.
INSTALLATION
-
Pumps must be level
upon installation, Dimensions and position of the pump for supporting and fixing the pump within this
space (Fig.3).
-
Pump must be fixed by screws on the spa shelf, and fixed with a silent block or foam pad to lower noise and vibration. Do not
glue or tie d
own!
-
The pump will get hot during operation, To assist cooling, the minimum distance between the pump motor and the
surrounding
structure should be, not be less then 25mm.
-
The suction pipe of the pump should be as short as possible.
-
The rating label mu
st be visible after installation.
-
Parts containing live parts, except parts supplied with safety extra low voltage<12V, must be inaccessible to a person in the
Spa.
-
Class I appliances must be permanently connected to fixed wiring. Parts including electrica
control devices, must be located or fixed so that they cannot enter or fall into the bath.
PIPE ASSEMBLY
-
The maximum inle
t water pressure is
-
The suction pipes should have a diameter equal to or larger than that of t
loss of head and improves efficiency. The suction and discharge pipes should not be placed above the pump in all cases.
-
Ensure a good seal on all connectors and unions. Avoid any water dripping onto motor, to
electrical.
-
Do not re
-
use old hose or connections. Replace with new hose and fittings.
ELECTRICAL CONNECTIO
N
-
The electrical installation should have a multiple separation system with contacts opening at least 3mm.
-
For continu
ed protection against possible electric shock this unit is to be mounted to the base in accordance with the
installation instructions.
IMPORTANT SAFETY INSTRUCTIONS
When installing and using this electrical equipment, basic safety
precautions should always be followed,
including the following: READ AND FOLLOW ALL
INSTRUCTIONS.
reduce the risk of injury. Do not permit children to use this product
unless
they
are
closely
Risk of Electrical Shock. Connected only to grounding type receptacle protected by a ground fault circu
Contact a qualified electrician if you cannot verify that the receptacle is protected by GFCI.
Do not bury cord. Locate cord to minimise damage from other
equipment & nearby objects.
can cause injury. D
o not make the electric
pump
live
before
the
pipeline
has
reduce the risk of electrical shock, replace damaged cord immediately.
electrical
shock,
do
not
use
an
extension
cord
to connect
to
electric
supply;
fixed
-
installed
bath
tubs & Spas;
it
is
not
suitable
for swimming pools.
enclosure
or
beneath
the
skirt
of
a
hot
tub
unless so
marked.
into
fixed
wiring
in
accordance with
NZ wiring
regulations.
inadvertent
resetting
of
the
thermal
cut
-
out,
this appliance must not be supplied through an
external switching device, such as a timer,
or
connected
to
a
circuit
that
is
regularly
switched
on
and
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
groundwater and get into the fo
od chain, damaging your health and well
-
being.
correct installation, and optimum performance of Bad Boy Spa
Fox
single
stage centrifugal pumps
designed to operate with compact hydro massage equipment, They are
equipped with a total emptying system to prevent the discharge of residual water in each stop cycle
These units are designed to operate with cle
an water at maximum water temperature of 50
°
C.
C. Relative Air Humidity: 95% Max.
Built of top quality materials; they are subjected to strict hydraulic and
electrical controls and are carefully verified.
ion is ensured by following these instructions and those of the wiring diagram; otherwise, over loads may be
produced in the motor. We decline responsibility for any damage caused by not following these instructions.
upon installation, Dimensions and position of the pump for supporting and fixing the pump within this
Pump must be fixed by screws on the spa shelf, and fixed with a silent block or foam pad to lower noise and vibration. Do not
The pump will get hot during operation, To assist cooling, the minimum distance between the pump motor and the
structure should be, not be less then 25mm.
The suction pipe of the pump should be as short as possible.
st be visible after installation.
Parts containing live parts, except parts supplied with safety extra low voltage<12V, must be inaccessible to a person in the
Class I appliances must be permanently connected to fixed wiring. Parts including electrica
l components, except remote
control devices, must be located or fixed so that they cannot enter or fall into the bath.
t water pressure is
≤0.15 MPa.
The suction pipes should have a diameter equal to or larger than that of t
he
discharge pipes. This assists and
loss of head and improves efficiency. The suction and discharge pipes should not be placed above the pump in all cases.
Ensure a good seal on all connectors and unions. Avoid any water dripping onto motor, to
avoid damage to motor and
use old hose or connections. Replace with new hose and fittings.
The electrical installation should have a multiple separation system with contacts opening at least 3mm.
ed protection against possible electric shock this unit is to be mounted to the base in accordance with the
2
precautions should always be followed,
closely
supervised
at
all
Risk of Electrical Shock. Connected only to grounding type receptacle protected by a ground fault circu
it
equipment & nearby objects.
has
been
connected &
supply;
provide
a
properly
for swimming pools.
this appliance must not be supplied through an
and
off
by
the
utility.
separate collection facilities.
Contact your local government for information regarding the collection systems available.
If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the
single
speed spa pumps,
designed to operate with compact hydro massage equipment, They are
equipped with a total emptying system to prevent the discharge of residual water in each stop cycle
.
electrical controls and are carefully verified.
ion is ensured by following these instructions and those of the wiring diagram; otherwise, over loads may be
produced in the motor. We decline responsibility for any damage caused by not following these instructions.
upon installation, Dimensions and position of the pump for supporting and fixing the pump within this
Pump must be fixed by screws on the spa shelf, and fixed with a silent block or foam pad to lower noise and vibration. Do not
The pump will get hot during operation, To assist cooling, the minimum distance between the pump motor and the
Parts containing live parts, except parts supplied with safety extra low voltage<12V, must be inaccessible to a person in the
l components, except remote
discharge pipes. This assists and
avoids the
loss of head and improves efficiency. The suction and discharge pipes should not be placed above the pump in all cases.
avoid damage to motor and
The electrical installation should have a multiple separation system with contacts opening at least 3mm.
ed protection against possible electric shock this unit is to be mounted to the base in accordance with the

o
The
protection
of the
tripping current
not
o
Single
-
phase motors have built
-
The electric connection should be carried out by qualified staff following strictly appropriate NZ standards.
-
Be sure that the earth ca
ble connection is correctly made.
-
Wires serving as equipotential bonding conductors shall have a cross sectional area between 2.5
be equipped with a terminal suitable receptacles
CONTROLS PRIOR TO IN
ITIAL START
-
Verify that the
pump shaft turns freely.
-
Check that the mains voltage and frequency are according to the name plate.
-
The hydromassage assembly should be equipped with a system to prevent
water level
is not
present.
-
Check th
e
rotating direction
of
the motor, which should concur with
-
If the motor does not start up, try to locate the problem in the table of most
is provided further on in this
manual.
CAUTION: THE PUMP SHOULD NEVER OPERATE DRY.
START
-
UP
Ensure Spa valves are open and water is available to flow.
Start electrically
,
the pump only
,
when the suction and discharge pipes are connected to the corresponding inlets and outlets.
Switch on pump
and
suitably adjust
the
MAINTENANCE AND CLEA
NING
Our pumps for hydromassage/Spa facilities do not require any special maintenance or programming. If the pump will remain
idle for a long period of time, it is recommended to disassemble, clean and store it in a dry, well ventilated place. If the
cor
d is damaged, it must be replaced by the manufacturer or its service agent or a
TROUBLE SHOOTING GUI
DE
SYMPTOM
POSSIBLE
CAUSE
Pump
Does
No
t
Turn
No
Power
To
Pump
-
Incoming power to the pump?
-
Is
circuit breaker on?
-
Is GFCI operating properly?
-
Is the air switch plugged in?
Air Switch
Disconnected
-
Is the air switch hose connected to the pump?
-
Is the air switch hose connected to the actuator button on the tub deck?
Pump Not
Pumping
Properly
Blockage Or
Leak
-
Is the water level in Spa adequate?
-
Jets should be pointed away from the suction inlet so air is not forced into pump suction.
-
Is the in tub
-
Is there any debris in the pump housing?
-
Is
there a leak in the piping or the pump?
Low Voltage
-
Is the proper voltage applied to the pump?
-
Is there an extension cord being used?
INSTALLATION DIAGRAM
of the
system should
be
based
on
a
residual
current
device (RCD) with
not
exceeding 30mA
.
The
supply cable should comply
with
phase motors have built
-
in thermal protection.
The electric connection should be carried out by qualified staff following strictly appropriate NZ standards.
ble connection is correctly made.
Wires serving as equipotential bonding conductors shall have a cross sectional area between 2.5
be equipped with a terminal suitable receptacles
.
ITIAL START
-
UP
pump shaft turns freely.
Check that the mains voltage and frequency are according to the name plate.
The hydromassage assembly should be equipped with a system to prevent
the
pump from
starting
the motor, which should concur with
that
indicated on the fan cover.
If the motor does not start up, try to locate the problem in the table of most
common faults and their possible solutions that
CAUTION: THE PUMP SHOULD NEVER OPERATE DRY.
Ensure Spa valves are open and water is available to flow.
when the suction and discharge pipes are connected to the corresponding inlets and outlets.
the
jets
to
obtain
the
desired
flow
.
NING
Our pumps for hydromassage/Spa facilities do not require any special maintenance or programming. If the pump will remain
idle for a long period of time, it is recommended to disassemble, clean and store it in a dry, well ventilated place. If the
d is damaged, it must be replaced by the manufacturer or its service agent or a
suitably
qualified person to avoid a hazard.
CHECK
Incoming power to the pump?
circuit breaker on?
Is GFCI operating properly?
Is the air switch plugged in?
Is the air switch hose connected to the pump?
Is the air switch hose connected to the actuator button on the tub deck?
Is the water level in Spa adequate?
Jets should be pointed away from the suction inlet so air is not forced into pump suction.
Is the in tub
suction inlet
blocked
or
covered?
Is there any debris in the pump housing?
there a leak in the piping or the pump?
Is the proper voltage applied to the pump?
Is there an extension cord being used?
3
device (RCD) with
a rated
with
EMC
standards.
The electric connection should be carried out by qualified staff following strictly appropriate NZ standards.
Wires serving as equipotential bonding conductors shall have a cross sectional area between 2.5
mm
2
and
6mm
2
and shall
starting
up if
a
minimum
indicated on the fan cover.
common faults and their possible solutions that
when the suction and discharge pipes are connected to the corresponding inlets and outlets.
Our pumps for hydromassage/Spa facilities do not require any special maintenance or programming. If the pump will remain
idle for a long period of time, it is recommended to disassemble, clean and store it in a dry, well ventilated place. If the
supply
qualified person to avoid a hazard.
Is the air switch hose connected to the actuator button on the tub deck?
Jets should be pointed away from the suction inlet so air is not forced into pump suction.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
lack of experience
and
knowledge,
unless they have been given adequate
the
appliance
by
a
person
responsible
Children should be supervised to ensure that they do not play with this appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, service agen
hazards.
WARRANTY
In the unlikely event you experience any issues with your Bad Boy pump, w
the dealer from which you purchased the Pump who will organise repair
purchase that clearly demonstrates the product name, its date of purchase and the place of purchase
warranty. The onus is on the purchaser to return the pump to the dealer at the p
ITEMS NOT COVERED BY
THE WARRANTY
-
Claims outside the 1
year warranty period
-
Fair wear & tear
-
Consumables
–
including mechanical seals, bearings, capacitors, o
-
Damage resulting from misuse, neglect, improper use outside design
-
Improper or inadequate installation or operation
-
Voltage spikes, corrosive chemicals
-
Unauthorised persons attempting repairs or modifications
-
When used in a commercial or non
Space Industries Ltd is not liable for any consequential losses associated with this Bad Boy Pump for whatever reason. Nor ar
they liable for any damage or injury caused directly or indirectly as a result of the operation of this Bad Boy Pump.
This limi
tation does not negate our obligations under the New Zealand Consumer Guarantees’ Act.
Space Industries Limited
16
0
Plunket Ave
Manu
kau City
Auckland 2104
Ph [phone]
[e-mail].n
z
www.spaceindustries.co.nz
Code
Power
P1
P2
HP
(Output)
A
BBSF02
0.25
0.19
0.25
100
BBSF03
0.37
0.25
0.35
100
BBSF05
0.55
0.37
0.5
112
BBSF07
0.75
0.66
0.75
112
BBSF10
0.9
0.75
1.0
112
BBSF12
1.10
0.9
1.2
121
BBSF15
1.50
1.1
1.5
121
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
unless they have been given adequate
supervision
or
instruction
responsible
for their
safety.
Children should be supervised to ensure that they do not play with this appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, service agen
t or a qualified person in order to avoid
In the unlikely event you experience any issues with your Bad Boy pump, w
ithin 1
year
of the date of purchase;
the dealer from which you purchased the Pump who will organise repair
or replacement. Ensure you have a valid proof of
purchase that clearly demonstrates the product name, its date of purchase and the place of purchase
.
warranty. The onus is on the purchaser to return the pump to the dealer at the p
urchasers own expense.
THE WARRANTY
year warranty period
including mechanical seals, bearings, capacitors, o
-
rings
Damage resulting from misuse, neglect, improper use outside design
parameters
Improper or inadequate installation or operation
Voltage spikes, corrosive chemicals
Unauthorised persons attempting repairs or modifications
When used in a commercial or non
-
domestic application, warranty is for
6 months
only.
Space Industries Ltd is not liable for any consequential losses associated with this Bad Boy Pump for whatever reason. Nor ar
they liable for any damage or injury caused directly or indirectly as a result of the operation of this Bad Boy Pump.
tation does not negate our obligations under the New Zealand Consumer Guarantees’ Act.
Dimensions (mm)
A
B
C
D
E
F
L
H
H1
H2
100
153
80
164
33
89
317
191
168
63
100
153
80
164
33
89
317
183
168
63
112
156
90
17
2
44
86
3
47
205
179
74
112
156
90
172
44
66
347
205
179
74
112
156
90
172
44
86
347
205
179
74
121
187
90
218
38
120
402
210
211
90
121
187
90
218
38
120
402
210
211
90
Performance Curve
4
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities,
or
instruction
concerning
use
of
t or a qualified person in order to avoid
of the date of purchase;
p
lease contact
or replacement. Ensure you have a valid proof of
.
This is a return to base
urchasers own expense.
Space Industries Ltd is not liable for any consequential losses associated with this Bad Boy Pump for whatever reason. Nor ar
e
they liable for any damage or injury caused directly or indirectly as a result of the operation of this Bad Boy Pump.
Performance Curve