SPALDING SPA0366 User manual

Toll-Free Customer Service Number
U.S.: 1-800-558-5234
Canada: 1-800-284-8339
Europe: [phone]
Australia: 1300 367 582
www.spalding.com
4/21 ID# M6E11E00
Model Number:
(found on product box)
WARNING
READ AND UNDERSTAND THE OPERATOR’S
MANUAL BEFORE USING THIS UNIT.
FAILURE TO FOLLOW THE OPERATING
INSTRUCTIONS COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
PORTABLE BASKETBALL SYSTEM
Owner’s Manual

Contents
2
Contents
Before You Begin..................................2
Contact ..........................................2
Warranty.........................................2
Safety Information ................................3
Package Contents.................................4
Tools & Materials for Assembly......................6
Assembly Overview................................7
Fill the Base ......................................8
Assemble the Extension Arm. . . . . . . . . . . . . . . . . . . . . . . .9
Assemble the Backboard..........................10
Assemble the Rim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Assemble the Upright .............................14
Assemble the Front Cover .........................18
Assemble the Handle Assembly ....................20
Operation .......................................22
Parts List .......................................23
Questions or Missing Parts?
Call TOLL-FREE Customer Service
Number listed on the front page!
DON’T go back to store!
Before You Begin
READ AND UNDERSTAND THE OPERATOR’S MANUAL BEFORE USING THIS UNIT.
• Remove ALL contents from boxes.
• This manual, accompanied by a sales receipt, should be saved and kept on hand as a convenient reference,
as it contains important information about your model.
WARNING
FAILURE TO FOLLOW OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR PROPERTY DAMAGE.
Contact
Questions or missing parts? Do NOT go back to the store!
Email: [e-mail]
Customer Service
Toll-Free Number: 1-800-558-5234
Mailing Address: Spalding
PO Box 90015
Bowling Green, KY 42102
Warranty
For the very latest Basketball System Warranty information, please visit www.Spalding.com or call
Spalding Customer Service at 1-800-558-5234.

Safety Information
3
Safety Information
WARNING
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND
WILL VOID THE WARRANTY.
Owner must ensure all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check the entire box
and inside all of the packing material for parts and/or additional instruction material. Before beginning assembly, read
the instructions and identify parts using the hardware identier and parts list in this document. Proper and complete
assembly, use, and supervision are essential for proper operation and to reduce the risk of accident or injury. A high
probability of serious injury exists if this system is not installed, maintained, and operated properly.
• If using a ladder during assembly, use extreme caution.
• Check the base regularly for leakage. Slow leaks could cause the system to tip over unexpectedly.
• Seat the pole sections properly (if applicable). Failure to do so could allow the pole sections to separate during play
and/or during transport of the system.
• Climate, corrosion, or misuse could result in system failure.
• If technical assistance is required, contact Customer Service.
• Minimum operational height is 6'-6" (1.98 m) to the bottom of backboard.
Most injuries are caused by misuse and/or not following instructions.
Use caution when using this unit.
NOTICE
• Adult assembly required.
• Dispose of ALL packaging materials promptly.
• As with all products, periodically inspect for loose, small parts.
• Assembled unit MUST be lled with sand or water at ALL times.
• ALL basketball systems, including those used for DISPLAYS, MUST be assembled and installed according to
instructions.
• Failure to follow instructions could result in SERIOUS INJURY.
• It is NOT acceptable to devise a makeshift support system.
NOTE
Backboard style will vary.

Package Contents
4
Package Contents
Check the contents of each kit and other parts to ensure that all components are present. Keep the kit hardware in
the labeled bag as they will be used in different assembly steps.
See "Parts List" on page 23 for a complete list of replacement part numbers.
PRIMARY ASSEMBLY COMPONENTS
#1
#6
#2 #3
#4
#9
#31
#5
#7
#28
1Primary Sub-Assembly (x1) 2Extension Arm (x1) 3Backboard Assembly (x1)
4Rim (x1) 5Rim Cover, Orange (x1) 6Front Cover (x1)
7Knuckle Shroud (x1) 9Rim Bracket (x1) 28 Plug, Base (x2)
31 Cover, Extension Arm (x1)
KIT 1 – 209220
204961 hex head bolt 3/8-16 x 5/8
#8
8Bolt, Hex, 3/8-16 x .625" (x4)

Package Contents
5
KIT 2 – 209221
#10
203100
NUT, HEX FLANGE, 5/16-18
#11
#12
10 Bolt, Hex, Flange, 5/16-18 x 1" (x4) 11 Nut, Wiz, 5/16-18 (x4) 12 T-Bolt (x1)
KIT 3 – 209242
#13
#14
#15 #16 #17
13 Spring (x1) 14 Nut, Special (x1) 15 Washer, Flat, 1.5" OD (x1)
16 Bracket, Reinforcement (x1) 17 Screw, 1/4 x 0.375" Long (x2)
KIT 4 – 209184
#30 #32
#201139 hex head bolt,1/2 x 4 1/2 - 13
#18 #21
#19
#20
#22
18 Washer, .375" ID (x2) 19 Nut, Acorn, Locking, 5/16-18 (x2) 20 Pull Pin (x1)
21 Bolt, Hex, 1/2-13 x 4.5" (x1) 22 Nut, Nylock, 1/2-13 (x1) 30 Washer, Flat, 1/4 (x2)
32 Screw, 1/4 x 0.75 (x2)

Tools & Materials for Assembly
6
KIT 5 – 209224
208505
#23 #24 #25
23 Bolt, Carriage, 1/4-20 x 1.5" (x8) 24 Knob, 1/4-20 (x8) 25 Thumbscrew, M8 x 1.25 (x2)
KIT 6 – 209225
#27
#26
26 Handle Assembly (x1) 27 Pull Pin, Handle (x1)
Tools & Materials for Assembly
2 Capable
Adults
Safety
Glasses
Socket Wrench
1/2", 9/16",
3/4"
Wrench
1/2", 9/16",
3/4"
Phillips
Screwdriver
Sand/Garden
Hose
Step Ladder
(8 ft.)
(OPTIONAL)
Adjustable
Wrenches

Assembly Overview
7
Assembly Overview
Backboard (Section B, C)
Crank Handle (Section G)
Base (Section A)
Rim (Section D)
Pole (Section E)
Front Cover (Section F)
Extension Arm Cover (Section H)

Fill the Base
8
Fill the Base
Required Parts: Completed Base Assembly:
• SAND/GARDEN HOSE
AFILL THE BASE
1. Roll the primary sub-assembly to
the desired location for use.
2. Fill the base with water (approx.
36 gallons (136 Liters)) or sand
(approx. 400 lbs. (181 kg)).
3. Insert the cap (28) into the base
to close.
#1 #28
NOTE
As base is being lled, you may monitor the ll status and proceed with Assemble the Extension Arm, Assemble the
Backboard, and Assemble the Rim sections. DO NOT proceed with Assemble the Upright section until base is completely
lled.
WARNING
• FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
• THE CAP MUST BE TIGHTENED COMPLETELY AND SECURELY TO PREVENT LEAKAGE.
• CONTACT CUSTOMER SERVICE IMMEDIATELY IF THE CAP IS MISSING OR DAMAGED.
• CHECK THE WATER LEVEL BEFORE EACH USE.

Assemble the Extension Arm
9
Assemble the Extension Arm
Required Parts: Completed Base Assembly:
• KIT 1
• WRENCHES AND/OR SOCKET
WRENCHES (9/16")
BINSTALL THE EXTENSION ARM
1. Attach the extension arm (2) to the middle pole using the hex bolts (8).
2. Tighten the hex bolts (8) in the pre-welded nuts on the pole.
#2
#8

Assemble the Backboard
10
Assemble the Backboard
Required Parts: Completed Goal Assembly:
• KIT 2
• WRENCHES AND/OR
SOCKET WRENCHES
(1/2")
IMPORTANT
CAREFULLY CUT AND PEEL PROTECTIVE FILM AWAY FROM BOARD PRIOR TO ATTACHING RIM.
CINSTALL THE BACKBOARD
1. Insert the t-bolt (12) through the rim bracket (9).
2. Secure the rim bracket (9) to the backboard (3) and extension arm (2) using the bolts (10) and
nuts (11).
#12
#10
#11
#2
#9
#3

Assemble the Rim
11
Assemble the Rim
Required Parts: Completed Goal Assembly:
• KIT 3
• WRENCHES AND/OR
SOCKET WRENCHES
(3/4")
• PHILLIPS SCREWDRIVER
DASSEMBLE THE GOAL
1. Fit the rim (4) securely into the rim bracket (9). Allow the t-bolt (12) to slip through the center hole
in the rim (4).
#4
#9
#12
2. Install the reinforcement bracket (16) onto the t-bolt (12).
#12
#16

Assemble the Rim
12
DASSEMBLE THE GOAL
3. Install the spring (13) onto the t-bolt (12).
#13
#12
4. Install the special nut (14) and washer (15) onto the t-bolt (12).
5. Tighten the nut (14) until 1/8" of the bolt threads onto the exposed end of the t-bolt (12).
#14
#14
#15
#15
#13
#12
1/8"
(3mm)

Assemble the Rim
13
DASSEMBLE THE GOAL
6. Attach the cover (5) to the rim (4) using
the cover screws (17).
#5
#4
#17

Assemble the Upright
14
Assemble the Upright
Required Parts: Completed Pole Assembly:
• KIT 4
• WRENCHES AND/OR
SOCKET WRENCHES
(1/2"; 3/4")
WARNING
TWO PEOPLE ARE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS
INJURY AND/OR PROPERTY DAMAGE.

Assemble the Upright
15
EASSEMBLE THE POLE STRUTS
1. From the front of the unit, rotate the pole assembly upward. A second person must support the
backboard (3).
#3
18"
IMPORTANT
DURING STEPS 1-2, THE SECOND PERSON SUPPORTING BACKBOARD ONLY NEEDS TO LIFT TOP EDGE OF
THE BACKBOARD APPROXIMATELY 18" FROM THE GROUND. AFTER STEP 2 IS COMPLETED, THE SECOND
PERSON MAY GENTLY LOWER THE BACKBOARD BACK TO THE GROUND.
2. After rotating the poles up, rotate the struts into the threaded studs on the base.
3. Secure the struts in place with a washer (18) and nut (19).
#18
#19

Assemble the Upright
16
EASSEMBLE THE POLE STRUTS
4. Attach the extension arm cover (31) to the extension arm using screws (32) and washers (30).
#31
#32
#30
NOTE
The top edge of the backboard should rest on the ground for this assembly.
WARNING
• ENSURE THE BASE IS FILLED.
• TWO CAPABLE ADULTS ARE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING
COULD RESULT IN SERIOUS INJURY.
• DO NOT LEAVE THE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER.
5. Carefully rotate the pole into the upright position.
6. Insert the pull pin (20) through the front hole.
#20
FRONT
HOLE

Assemble the Upright
17
EASSEMBLE THE POLE STRUTS
7. Insert the hex bolt (21) and secure with the nut (22). Tighten completely.
IMPORTANT
YOU MAY NEED TO SLIGHTLY ADJUST POSITION OF PRIMARY UPRIGHT TO ACHIEVE PROPER HOLE ALIGNMENT
FOR BOLT INSERTION. GENTLY PUSH THE UPRIGHT BACK AND FORTH UNTIL PROPER CLEARANCE FOR BOLT
INSERTION IS ACHIEVED.
#21 #22
REAR
HOLE
8. Tighten the bolt and nut on the outside of the struts.

Assemble the Front Cover
18
Assemble the Front Cover
Required Parts: Completed Goal Assembly:
• KIT 5
IMPORTANT
ENSURE ALL CARRIAGE BOLTS ARE INSERTED PRIOR TO TIGHTENING COMPLETELY.
FASSEMBLE THE FRONT COVER
1. Attach the front cover (6) to the struts using carriage bolts (23) and tri-knobs (24).
#23
#6
#24

Assemble the Front Cover
19
FASSEMBLE THE FRONT COVER
2. Attach the knuckle shroud (7) using the carriage bolts (23), tri-knobs (24), and thumbscrews (25).
#23
#25
#7
#24
IMPORTANT
ENSURE ALL CARRIAGE BOLTS AND THUMBSCREWS ARE INSERTED PRIOR TO TIGHTENING COMPLETELY.

Assemble the Handle Assembly
20
Assemble the Handle Assembly
Required Parts: Completed Goal Assembly:
• KIT 6
GINSTALL THE HANDLE ASSEMBLY
1. Attach the crank handle assembly (26)
and pull pin (27).
#27
#26