Sparklan WNFB-266AXI User manual

Wireless Module
SparkLAN
WNFB-266AXI(BT) & AP12275_M2
HW User manual
Version 0.1
Revision History
Date
Revision Content
Revised By
Version
2020/11/26
Initial released
Ares
0.0
2021/01/04
Updated picture of device.
Ares
0.1

Wireless Module
Contents
Revision History............................................................................................................... 0
1. WNFB-266AXI(BT) & AP12275_M2 Evaluation Board Introduction ........................ 1
1-1. Interface Highlights........................................................................................ 1
List of Figures
Figure1. Top view of WNFB-266AXI(BT) & AP12275_M2 EVB ....................................................1

1
Wireless Module
1. WNFB-266AXI(BT) & AP12275_M2 Evaluation
Board Introduction
The WNFB-266AXI(BT) & AP12275_M2 evaluation board (EVB) is shown in Figure 1.
This specifically provides customers as a test application for WNFB-266AXI(BT) &
AP12275_M2 products. It provides communication interface conversion, functional I/O
voltage level switching, and external power supply test points. There are controller pins
on evaluation board which describes as below.
Figure1. Top view of WNFB-266AXI(BT) & AP12275_M2 EVB
1-1. Interface Highlights
1. J2: 5V DC adaptor input connector
2. J10: PCI-e Half Mini Card Connector (Female) and Latch.
3. J3: UART interface connects with USB port.
4. J4: SDIO Card Connector.

2
Wireless Module
Federal Communication Commission Interference Statement:
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
RF exposure statements
This Transmitter must not be co‐located or operating in conjunction with any other
antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body or nearby
persons.
CFR 47 FCC PART 15 SUBPART C (15.247) and SUBPART E (15.407) has been
investigated. It is applicable to the modular transmitter.
The devices must be installed and used in strict accordance with the manufacturer's
instructions as described in the user documentation that comes with the product.
This radio transmitter RYK-WNFB266AXIBT has been approved by Federal
Communications Commission to operate with the antenna types listed below, with the

3
Wireless Module
maximum permissible gain indicated. Antenna types not included in this list that have a
gain greater than the maximum gain indicated for any type listed are strictly prohibited for
use with this device.
Unique antenna connector (RP-SMA) must be used on the Part 15 authorized
transmitters used in the host product.
Antenna Type Antenna Model
Maximum Gain (dBi)
Remark
2.4 GHz 5GHz
Dipole AD-103AG 2.02 dBi 2.03 dBi
Dipole AD-302N 3.14 dBi 2.73 dBi
Dipole AD-303N 3.14 dBi 3.24 dBi
Length of Antenna cable:150mm Connector type of Antenna cable: I-PEX/MHF4 to
RP-SMA(F)
If the FCC identification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display
a label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains Transmitter Module FCC ID: RYK-WNFB266AXIBT” Or “Contains
FCC ID: RYK-WNFB266AXIBT”
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC
transmitter rules) listed on the grant, and the host product manufacturer is responsible
for compliance to any other FCC rules that apply to the host not covered by the modular
transmitter grant of certification. The final host product still requires Part 15 Subpart B
compliance testing with the modular transmitter installed.

4
Wireless Module
Industry Canada statement:
This device complies with Industry Canada license-exempt RSSs. Operation is subject to
the following two conditions:
1) This device may not cause interference, and
2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils
radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :
1) l’appareil ne doit pas produire de brouillage;
2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si le
brouillage est susceptible d’en compromettre le fonctionnement.
Caution:
1) The device for operation in the band 5150–5250 MHz is only for indoor use to reduce
the potential for harmful interference to co-channel mobile satellite systems;
2) For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the
equipment still complies with the e.i.r.p. limit;
3) For devices with detachable antenna(s), the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with
the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as
appropriate; and
Avertissement:
1) Le dispositif fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour
une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux
systèmes de satellites mobiles utilisant les mêmes canaux;
2) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)
utilisant les bandes 5250-5350 MHz et 5470-5725 MHz doit se conformer à la imitation
P.I.R.E.;
3) Le gain maximal d’antenne permis pour les dispositifs avec antenne(s) amovible(s)
utilisant la bande 5725-5850 MHz doit se conformer à la limitation P.I.R.E spécifiée pour
l’exploitation point à point et non point à point, selon le cas.

5
Wireless Module
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies
pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.
This radio transmitter (IC: 6158A-NFB266AXIBT has been approved by Industry Canada
to operate with the antenna types listed below with the maximum permissible gain
indicated. Antenna types not included in this list, having a gain greater than the
maximum gain indicated for that type, are strictly prohibited for use with this device.
Le présent émetteur radio (IC: 6158A-NFB266AXIBT a été approuvé par Industrie
Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain
admissible maximal. Les types d'antenne non inclus dans cette liste, et dont le gain est
supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur.
Antenna Type Antenna Model
Maximum Gain (dBi)
Remark
2.4 GHz 5GHz
Dipole AD-103AG 2.02 dBi 2.03 dBi
Dipole AD-302N 3.14 dBi 2.73 dBi
Dipole AD-303N 3.14 dBi 3.24 dBi
If the ISED certification number is not visible when the module is installed inside another
device, then the outside of the device into which the module is installed must also display
a label referring to the enclosed module. This exterior label can use wording such as the
following: “Contains IC: 6158A-NFB266AXIBT”.
Si le numéro de certification ISDE n'est pas visible lorsque le module est installé à
l'intérieur d'un autre appareil, alors l'extérieur de l'appareil dans lequel le module est
installé doit également afficher une étiquette faisant référence au module inclus. Cette
étiquette extérieure peut utiliser un libellé comme celui-ci: “ Contient IC:
6158A-NFB266AXIBT“.
Plaque signalétique du produit final:

6
Wireless Module
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 6158A-NFB266AXIBT ".
Manual Information To the End User:
The OEM integrator has to be aware not to provide information to the end user regarding
how to install or remove this RF module in the user’s manual of the end product which
integrates this module.
The end user manual shall include all required regulatory information/warning as show in
this manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur
final quant à la façon d'installer ou de supprimer ce module RF dans le manuel de
l'utilisateur du produit final qui intègre ce module. Le manuel de l'utilisateur final doit
inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manue
Must use the device only in host devices that meet the FCC/ISED RF exposure category
of mobile, which means the device is installed and used at distances of at least 20cm
from persons.
The end user manual shall include FCC Part 15 /ISED RSS GEN compliance statements
related to the transmitter as show in this manual.
Host manufacturer is responsible for compliance of the host system with module
installed with all other applicable requirements for the system such as Part 15 B, ICES
003.
Host manufacturer is strongly recommended to confirm compliance with FCC/ISED
requirements for the transmitter when the module is installed in the host.
Must have on the host device a label showing Contains FCC ID: 6158A-NFB266AXIBT,
Contains IC: 6158A-NFB266AXIBT
The use condition limitations extend to professional users, then instructions must state
that this information also extends to the host manufacturer’s instruction manual.
If the end product will involve the Multiple simultaneously transmitting condition or
different operational conditions for a stand-alone modular transmitter in a host, host
manufacturer have to consult with module manufacturer for the installation method in
end system.
l'hôte doit utiliser l'instrument uniquement dans des dispositifs qui répondent à la fcc /
(catégorie d'exposition rf mobile, ce qui signifie le dispositif est installé et utilisé à une

7
Wireless Module
distance d'au moins 20 cm de personnes.
le manuel de l'utilisateur final doit inclure la partie 15 / (fac rss gen déclarations de
conformité relatives à l'émetteur que de montrer dans ce manuel.
le fabricant est responsable de la conformité de l'hôte, le système d'accueil avec le
module installé avec toutes les autres exigences applicables du système comme la
partie 15 b, ices - 003. accueillir le fabricant est fortement recommandé de confirmer la
conformité avec les exigences de la fcc / (émetteur lorsque le module est installé dans
l'hôte.
le dispositif d'accueil doivent avoir une étiquette indiquant contient FCC ID:
RYK-WNFB266AXIBT, contient IC : 6158A-NFB266AXIBT