SPAWN interlink 6 User manual

Remove LL4’s
rear guard and
unplug the
hoses
Place either jet
pack (they are
interchangeable)
into RL3’s left
shoulder hole
Remove ankle
shields, knee
shield and
connector for
each leg
The inner
ankle
shields are
to be
pegged to
the opposite
hip hole. Lift
torso armor
to enable
you to
connect the
to shields
together
The shields connect together under
the armor. The shields also peg
together in the back
Move outer ankle shields up to
thighs, then plug rear guard tabs
and pegs into shield slots and
holes
910
5
67
STEPS FOR ASSEMBLING INTERLINK 6
Connect RL3 legs
together by two pegs
Swing cover from side of foot to
front and peg into hole Remove
jet packs
from back
Remove
both arms.
4
3
2
1
8
NOTE:
Removed
parts may
be used at
different
stages of
assembly.
ASSEMBLY
INSTRUCTIONS PAGE 1

Remove
pod/antenna
assembly of HD1 as
well as right
forearm cover
17
Extend
torso by
pulling
up
17
18
Legs of HD1
should be
rotated up
(90°from
torso),
exposing a
hole in the
upper ball
joint. That
hole pins
onto the
empty head
post of TS2
HD1≥TO≤TS2
CONNECTING
Rear guard hoses peg into back
of feet
11
Remove
hand,
slide arm
gun off,
then
reattach
hand.
12 Fold
arms
behind
back
13
Place other jet pack
into top right shoulder
hole of LL4
14 15
Move shoulder
shield up
Flip down TS2’s
chest block and
snap square plug
in hole
16 Remove head from front
of body and pin onto
chest block
opening. Plug
hose into hole
on chest
block near
hinge
ASSEMBLY
INSTRUCTIONS PAGE 2
STEPS FOR ASSEMBLING INTERLINK 6 - CONTINUED

HD1’s foot plates
have a loop at
the end that
attaches to
hooks at
the back
feet of
TS2
There are two T-pins on
TS2 that slide into the
lower ball joint of HD1.
Slide the longer side of
the T-pin bar into one of
the side holes as far as
you can, allowing room
to rotate the other T-pin
bar to line up with the
other hole.
Then move HD1 to be center in the middle of T-pins.
You may have to repin HD1 back onto head post of TS2
21
Arms
from
RL3
plug
into
holes
of TS2
located
at the
side of
it’s
torso
22
RL3≥TO≤TS2
CONNECTING
The key lock tab from RL3’s jet pack pins
into holes in TS2’s chest block.
After inserting tab,
turn leg to lock in tab
23 LL4≥TO≤TS2
CONNECTING
Repeat same
procedure as
in step 22
and step 23
24
Remove
inner
leg
covers
on RA5
and peg
into
chest
plate
25
20
19
ASSEMBLY
INSTRUCTIONS PAGE 3
STEPS FOR ASSEMBLING INTERLINK 6 - CONTINUED

Press feet
together and
insert peg
into hole
Remove
right arm
and head
27
Peg right arm
into head hole
28
26
Turn lower
torso and
legs
around
180°
29
30
Once
connected
rotate RA5
forward to
lock on arm
onto TS2
31
RA5≥TO≤TS2
CONNECTING
The key lock hole in RA5’s
back fits onto key lock tab
from TS2’s shoulder
Remove
shoulder
canopy
of LA6
32 Detach all pieces from
shoulder canopy
33 34 Detach lower
leg shield and
left forearm
covering
ASSEMBLY
INSTRUCTIONS PAGE 4
STEPS FOR ASSEMBLING INTERLINK 6 - CONTINUED

35 36
37
38
39
40
41
42 43
Turn out legs at
upper thigh to have
heels and calves
back to back.
Then pivot feet
to point
up
Take one lower leg shield and peg
into holes on front side. Repeat on
backside with other shield
Peg the
shield
that
was on
the
forearm
to the
back
Connect the two
pieces taken off
the shoulder
canopy together
Then connect those two
pieces to the shoulder
canopy as shown
Continue by pegging that canopy assembly
into two holes in LA6’s back
Shoulder claws
peg into holes on
soles of shoes
Flip down head to
expose key lock hole
for attaching to TS2 Line up slot from LA6 to peg of TS2 and
push together. Then rotate arm forward to
lock on peg
LA6≥TO≤TS2
CONNECTING
ASSEMBLY
INSTRUCTIONS PAGE 5
STEPS FOR ASSEMBLING INTERLINK 6 - CONTINUED

STEPS FOR ASSEMBLING FUELING STATION FOR INTERLINK 6
2
1
Place right base piece onto left
base piece to connect
Take the
long
uprights
and plug
into base
4
3
Connect the
elbow pieces to
the uprights Connect the
feet to the
base by
pinning to
pegs
INTERLINK 6≥TO≤BASE
CONNECTING
5
Plug the
elbow pieces
into booster
rockets on
bottom foot
panel of TS2
ASSEMBLY
INSTRUCTIONS PAGE 6

LOCATION OF REMAINING PARTS Gun from LL4 Mask from
LL4
Forearm pad
from HD1 Gun turrets from
TS2
Arm
cover
from
LL4
Helmet from LL4
Kneecap
covers
from LL4
back shield
from RL3
Neck guard
from LA6
Foot
braces
from LL4
Front shield from
TS2
RIGHT SIDE/BACK VIEW
FRONT VIEW
LEFT SIDE VIEW
ASSEMBLY
INSTRUCTIONS PAGE 7

INDIVIDUAL ROBOT
ASSEMBLY for HD1 Proceed to peg
pod/antenna assemble to
shoulder guard cover.
Larger two pegs attach to
HD1’s left side and smaller
pegs go to right side.
After removing robot from
packaging you will need to
attach each 8”antennas to
a shoulder pods as shown.
Antennas are
interchangeable and cannot
be removed after they are
attached to pod.
The two gun turrets plug onto
shoulders as shown.
Right arm gatling gun has wind-up
action. Turn clockwise to wind and
press release tab to spin
TS2
INDIVIDUAL ROBOT
ASSEMBLY for
INDIVIDUAL ROBOT
ASSEMBLY for
Load missile into hole
on right forearm pad.
Pull back and release to
fire
Jet packs plug into
either hole in back.
RL3
ASSEMBLY
INSTRUCTIONS PAGE 8

INDIVIDUAL ROBOT
ASSEMBLY for
Mask clips
onto back
hooks
LL4 Load missile into hole on right forearm pad.
Pull back and release to fire
Shoulder shields
plugs into holes
above arms
Helmet
snaps
into
collar
INDIVIDUAL ROBOT
ASSEMBLY for
Mask clips
over head
RA5 Pivot trigger up and down to move
chainsaw blades
INDIVIDUAL ROBOT
ASSEMBLY for LA6
Shoulder claws have
multiple pivot points
ASSEMBLY
INSTRUCTIONS PAGE 9