Makeblock m Bot mega User manual



󾙓󾙓󾙘󾙒󾙓󾙒󾙕󾙛󾙘󾙒󾙒󾙒


󾙖󾙕󾙓󾙒󾙒󾙓
After-sales services and technical support
            


󾙛󾙒󾙒󾙓󾙔󾙒󾙒󾙓󾙖󾙒󾙒󾙓󾙚󾙕󾙒

󾙓
󾙓
󾙓 󾙓 󾙓 󾙓 󾙔
󾙔󾙔󾙔󾙕󾙘󾙓󾙖
󾙓 󾙔
Parts List

󾙔󾙕
󾙛󾙕
󾙖󾙚󾙓󾙔
󾙓 󾙓 󾙓 
󾙕󾙔󾙗󾙚 󾙕󾙓󾙒󾙛 󾙕󾙓󾙙 󾙓󾙒
󾙔󾙘󾙒
󾙖
󾙔󾙘󾙔󾙚󾙖
Install MegaPi onboard electronic module
 

󾙖󾙗
Mount MegaPi to the body shell
⚠If Plastic Spacer is not used, the metal case will short-circuit the electronic module.
󾙓
󾙓
󾙕
󾙖󾙚󾙕
Mount IR Proximity sensors to the body shell
⚠If Plastic Spacer is not used, the metal case will short-circuit the electronic module.
󾙔
󾙕󾙔
󾙔
󾙕󾙓󾙒󾙔

󾙘󾙙
Mount RGB LED and impact switch to the motor bracket
󾙔
󾙔
󾙔
󾙕󾙖
󾙕󾙓󾙒󾙖
󾙖
󾙕󾙔󾙗󾙚
󾙕󾙚
󾙔
Mount DC motors to the motor bracket
⚠Please note the position of the electronic module and the mounting holes.

󾙚󾙛
󾙖
󾙔󾙘󾙔󾙚󾙖
Mount Mecanum wheels to the motor bracket
󾙔

󾙔󾙘󾙒


󾙓
󾙔
󾙔
󾙕󾙔
󾙕󾙓󾙒󾙔
Mount Line tracking sensors to the connector bracket
⚠If Plastic Spacer is not used, the metal case will short-circuit the electronic module.
⚠There are two kinds of Mecanum wheels, L and R, it should be as shown in the picture on
the right after installation(You can distinguish the wheels by the L, R mark on the inside of the
Mecanum wheels and the direction of the roller)

󾙓󾙒 󾙓󾙓
Mount Connector bracket to the motor bracket
󾙔
󾙖󾙚󾙔
⚠Please note the up and down of the mount connector and the line-tracking sensor in the picture.

󾙓󾙔 󾙓󾙕
Bodyshell installation
󾙓
󾙓
󾙓
󾙕󾙓
󾙕󾙓󾙒󾙓
Mount IR proximity sensor to the Upper shell
⚠If Plastic Spacer is not used, the metal case will short-circuit the electronic module.

 
A6 A7 A8 A9 A10 A11 A12 A14 A15
5V 5V GND RX2 TX2
GND
A13
SIG 5V GND
ON
OFF
$POOFDUBMMFMFDUSPOJDNPEVMFTXJUI.FHB1J
'PSTQFDJDDPOOFDUJPONFUIPEQMFBTFSFGFSUPUIFGPMMPXJOHQBHF
3BTQCFSSZ1J$PNNVOJDBUJPO
64##UZQFJOUFSGBDF 8JSFMFTT
DPNNVOJDBUJPONPEVMF
.PUPSESJWFS
)JHI1PXFS
%$TVQQMZ7 4UFQQFS%$NPUPSJOUFSGBDFY
)JHIQPXFSPVUQVU"
1PXFSTXJUDI
.NPVOUJOHIPMFY
4FSWPJOUFSGBDFY
"CPVU.FHB1J

󾙓󾙘 󾙓󾙙
A6 A7 A8 A9 A10 A11 A12 A14 A15
5V 5V GNDRX2 TX2
GND
A13
SIG 5V GND
A6 A7 A8 A9 A10 A11 A12 A14 A15A13
SIG 5V GND
A9A10
A11A12
A13A14
A6
A7
A8




󾙓
󾙔
󾙔
󾙔
󾙓
󾙕
󾙓 󾙔
󾙓
Please refer to the figure below to connect the electronic module
⚠If the Pins are connected in the wrong order, the electronic module may be damaged after
power on.

󾙔
󾙓 󾙕
󾙔
󾙔
󾙔 󾙓
󾙓
󾙓

Module location
⚠If the motors or left and right wheels are connected in the wrong order, they will not move in the
default direction. Encourage experimentation.