SpeakerCraft BassX Dual 6 User manual

OWNER’S MANUAL
BassX Series
Floor Standing Powered Subwoofer
BassX Dual 6

BassX-Dual 6 Owner’s Manual Page 3Page 2 BassX-Dual 6 Owner’s Manual
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufactur-
er’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding-type
plug has two blades and a third grounding prong. The wide blade or third prong
is provided for your safety. If the provided plug does not fit into your outlet, con-
sult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket or table specified by the
manufacturer or sold with the apparatus. When a cart is used, use caution when
moving the cart / apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of
time.
14. Refer all servicing to qualified service personnel. Servicing is required when the
apparatus has been damaged in any way, such as power-supply cord or plug is
damaged, liquid has been spilled or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture, does not operate normally, or
has been dropped.
15. The appliance couple of the power supply cord is used as the ultimate disconnect
device from mains. Remain the appliance couple readily operable.
16. Apparatus shall not be exposed to dripping or splashing and objects filled with
liquids shall not be placed on the apparatus.
SpeakerCraft’s BassX Dual 6 Compact Floor Standing Subwoofer provides accurate bass to any audio system, and is designed to work in conjunction with
your other audio components. The BassX Dual 6 can be connected to any surround sound receiver that has a subwoofer output, any receiver that has a
built-in preamplifier or any receiver that has speaker level outputs.
INTRODUCTION
For optimal performance, the BassX Dual 6 should be placed in a corner along the same wall as the front speakers. The unit is not shielded, so do not
place it too close to video devices. When choosing a place for the BassX Dual 6, please keep the following in mind: Placing the BassX Dual 6 in a corner
will increase the bass output. For details on placement, consult your local SpeakerCraft dealer.
DO
• Place the BassX Dual 6 with its feet resting on a solid flat level surface.
• Place the BassX Dual 6 in a well-vented area to provide proper cooling. In areas that lack proper ventilation, such as tight cabinets or racks, it may
be necessary to install small fans to create air movement.
DON’T
• Obstruct the woofers of the BassX Dual 6 it will hinder performance.
• Place the BassX Dual 6 in any position other than horizontal with the feet down. Never place on its side or resting on the back where the terminals are
located.
• Place the BassX Dual 6 near heat sources or in an area that it would be exposed to moisture.
PLACEMENT
CAUTION: Only make connections when the BassX Dual 6 is turned off.
Connecting the Line Level Audio Inputs (See Figure 1)
If your surround sound receiver or amplifier has only one subwoofer output, simply plug it into the
Left Line Input. If your receiver or amplifier has a built-in preamplifier, the left and right pre-outputs
can be connected to the left and right line level inputs.
Connecting the Line Level Audio Outputs (See Figure 1)
Sources connected to the left and right line level inputs can be forwarded to other components
or amplifers by connecting to the corresponding outputs. If your receiver or amplifier has a built-in
preamplifier, the left and right pre-inputs can be connected to these line level outputs.
INSTALLATION
Once the BassX Dual 6 is connected, use the controls described below to make adjustments so that it
will blend seamlessly with the other speakers in your system.
Power Switch (See Figure 2)
This switch turns the BassX Dual 6 on or off. The Standby light will illuminate green when switched
to the “On” position; when “Off”, the Standby light will illuminate red.
Volume Knob (See Figure 3)
Use this control to match the output of the BassX Dual 6 to that of the main speakers in the system.
We recommend that you play a variety of material before selecting a setting. Start with the control
in the 12 o'clock position for the optimal setting and adjust to your system as necessary.
Crossover Knob (See Figure 3)
Use this control to adjust the upper frequency limit of the BassX Dual 6. The purpose is to control the
overlap the upper frequencies of the sub and the main speakers’ lower frequencies. Start in the 12
o’clock position for the optimal setting.
Phase Switch (See Figure 4)
Allows you to toggle between 0° and 180° phase modes. Listen to the system and leave the switch
in the position that has more audible bass. The default setting is “0˚”.
OPERATION
The BassX Dual 6 Powered Subwoofer is designed to function trouble-free. Most problems occur due to operating errors. If you have a problem, please check
the troubleshooting list first. If the problem persists, contact your authorized SpeakerCraft dealer or SpeakerCraft Technical Support at 800.448.0976.
TROUBLESHOOTING
A hum or buzzing sound is heard. The sound may be caused by a ground loop in the system. Try to eliminate this
by reversing the AC plugs of other components in the system.
Try plugging the receiver into another outlet.
Other causes may include faulty cables.
The BassX Dual 6 will not turn on. The subwoofer must be plugged into a live AC outlet. The power switch on
the back panel must be on. A signal must be playing into the input jacks.
No sound is heard. Audio cable to the receiver is not connected properly or the cable is bad. Use
another cable that you know is good.
Check all wire connections and plugs.
Problem Possible Causes & Solutions
Figure 1:
Line Level Inputs/Outputs
APPLICABLE FOR USA, CANADA OR WHERE APPROVED FOR USAGE
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE PLUG TO WIDE
SLOT, INSERT FULLY.
ATTENTION: POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET
POUSSER JUSQU AU FOND.
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric
shock, do not remove cover (or back).
No user-serviceable parts inside. Refer
servicing to qualified service personnel.
IMPORTANT SAFETY INSTRUCTIONS
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated “dan-
gerous voltage” within the product’s enclosure
that may be of sufficient magnitude to consti-
tute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the presence
of important operating and maintenance (ser-
vicing) instructions in the literature accompany-
ing the appliance.
• Explanation of Graphical Symbols
WARNING
RISK OF ELECTRIC SHOCK
DO NOT EXPOSE TO MOISTURE
• To reduce the risk of fire or electrical
shock, do not expose the apparatus to
rain or moisture.
• A warning that an apparatus with CLASS
I construction shall be connected to a
MAINS socket outlet with a protective
earthing connection.
PORTABLE CART
WARNING
CAUTION: Please read the following important instructions carefully to ensure a safe operation.
Figure 2:
Power Switch; Standby Light
Figure 3:
Volume / Crossover Knobs
Optimal Settings Indicated
Figure 4:
Phase Switch
Default Setting Indicated

SPEAKER SPECIFICATIONS
940 Columbia Avenue, Riverside, CA 92507
[phone] Fax [phone]
www.speakercraft.com LITX0606
Page 4 BassX-Dual 6 Owner’s Manual
For technical inquires, please call 1-800-448-0976 or e-mail us at [e-mail]. We are available to assist you every
weekday, except holidays, between the hours of 7:00 a.m. and 5:00 p.m. PST.
SpeakerCraft offers a variety of accessories to make your installation of these speakers and other SpeakerCraft products easy, economical,
and professional. Contact your authorized SpeakerCraft Dealer for more information.
LIMITED 2-YEAR WARRANTY
SpeakerCraft Inc. warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship for a period
of two years, provided the product was purchased from a SpeakerCraft Authorized Dealer.
Defective products must be shipped, together with proof of purchase, prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased,
or to the SpeakerCraft factory at the address listed on this installation instruction manual. Freight collect shipments will be refused. It is preferable to ship
this product in the original shipping container to lessen the chance of transit damage. In any case, the risk or loss or damage in transit is to be borne by the
purchaser. If upon examination at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit was defective in materials or workmanship at any
time during this warranty period, SpeakerCraft or the SpeakerCraft Authorized Dealer will, at its option, repair or replace this product at no additional charge,
except as set forth below. If this model is no longer available and can not be repaired effectively, SpeakerCraft, at its sole option may replace the unit with a
current model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If mounting
surface modification is required, SpeakerCraft assumes no responsibility or liability for such modification. All replaced parts and product become the property of
SpeakerCraft Inc. Products replaced or repaired under this warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.
This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping
procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has not been
authorized or approved by SpeakerCraft. This warranty also excludes normal cosmetic deterioration caused by environmental conditions. This warranty will be
void if the Serial number on the product has been removed, tampered with or defaced.
This warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy
shall be repair or replacement as provided above. In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use
or inability to use the product, even if SpeakerCraft Inc. or a SpeakerCraft Inc. Authorized Dealer has been advised of the possibility of such damages, or for
any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and
exclusion may not apply.
All implied warranties on the product are limited to the duration of this expressed warranty. Some states do not allow limitation on the length
of an implied Warranty. If the original retail purchaser resides in such a state, this limitation does not apply.
In our attempt to constantly improve our products, features and specifications are subject to change without notice.
BassX Dual 6
System Configuration: Sealed Powered Subwoofer
Woofer: Dual 6½" Long Excursion Treated Paper
Cone Woofers with Butyl Surround
Frequency Response: 40Hz - 120Hz
Power Handling: 150 Watts
Additional Features: Auto Power On/Off
Anti-Clipping Circuitry
User Accessible Fuse
Dimensions: H 93
/4" x W 95 /8" x D 105 /8" w/heat sink
(Please allow 4" for terminal connections)
(Please add 1/2" for feet)
Weight 20 lbs