SpeakerCraft SDSi User manual

SDSi Subwoofer – Multivoltage
Triple 8” / Triple 10” / Triple 12” / Triple 15"
INSTALLATION GUIDE

Nortek Security & Control LLC
2
Table of ConTenTs
Important Safety Information ...........................................3
FCC Notice .......................................................3
Unpacking .........................................................4
Care ..............................................................4
Amplier Panel Features ..............................................4
Subwoofer Placement ................................................7
Connecting your Subwoofer (LFE) .......................................8
Connecting your Subwoofer (Stereo) .....................................9
Adjusting your Subwoofer .............................................10
Attention: To Our Valued Customers .....................................11
Specications.......................................................11
SDSi-8...........................................................11
SDSi-10..........................................................11
SDSi-12..........................................................11
SDSi-15..........................................................11
Limited 2-Year Warranty...............................................12
2-Year Warranty....................................................12
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution - changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du
Canada.
FCC and IC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102.
1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed
and operated with a minimum distance of 20 centimeters from user and bystanders.
Warning: The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102, and users can obtain Canadian information
on RF exposure and compliance from the Canadian Representative Product Solutions Group at Tel: [phone].

Nortek Security & Control LLC
3
ImporTanT safeTy InformaTIon
renseIgnemenTs de séCurITé ImporTanTs
1. Read these instructions
2. Keep these instructions
3. Heed all warnings
4. Follow all instructions
5. Do not use this apparatus near water
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding plug. A polarized plug has two
blades with one wider than the other. A grounding plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
t into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at the plugs, convenience
receptacles, and at the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold
with the apparatus. When a cart or rack is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualied personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. No naked ame sources, such as lighted candles, should be placed on the apparatus
16. WARNING: To reduce the risk of re or electric shock, do not expose this apparatus to rain or moisture. The apparatus shall not be exposed to dripping or splashing and
objects lled with liquids, such as vases, shall not be placed on apparatus.
17. WARNING: The mains plug/appliance coupler is used as disconnect device, the disconnect device shall remain readily operable.
18. WARNING: An apparatus with Class I construction (a three wire AC Mains cord) shall be connected to a mains socket outlet with a protective earthing
connection.
19. Correct disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased.
They can take this product for environmentally safe recycling.
1. Lisez ces instructions
2. Conservez-les
3. Tenez compte de tous les avertissements
4. Suivez toutes ces instructions
5. N’utilisez pas cet appareil près de l’eau
6. Nettoyez-le uniquement avec un chiffon sec.
7. Ne bloquez aucune fente de ventilation. Installez conformément aux instructions du fabricant.
8. Ne l’installez pas à proximité de sources de chaleur comme des radiateurs, des bouches de
chauffage, des cuisinières ou de tout autre appareil (y compris les amplicateurs) produisant de la
chaleur.
9. N’éliminez pas la fonction de sécurité de la che polarisée ou de mise à la terre. Une che polarisée
possède deux lames, dont l’une est plus large que l’autre. Une che de mise à la terre possède deux
lames et une troisième broche pour la mise à la terre. La broche large ou la troisième broche est
fournie pour votre sécurité. Si la che fournie ne rentre pas dans votre prise, consultez un électricien
pour remplacer la prise obsolète.
10. Sécurisez le cordon d’alimentation an d’éviter qu’on lui marche dessus ou qu’il soit pincé, en
particulier au niveau des ches, des prises de courant et au point de sortie de l’appareil.
11. Utilisez uniquement les xations/accessoires spéciés par le fabricant.
12. Utilisez uniquement avec le chariot, le support, le trépied, le support ou la table spéciés par le fabricant ou vendus avec l’appareil. Lorsqu’un chariot ou un support est
utilisé, faites preuve de prudence lorsque vous déplacez la combinaison chariot/appareil pour éviter les blessures dues au basculement.
13. Débranchez cet appareil pendant les orages ou lorsqu’il n’est pas utilisé pendant de longues périodes.
14. Conez les réparations à des réparateurs qualiés. La réparation est nécessaire lorsque l’appareil a été endommagé de quelque manière que ce soit, par exemple
lorsque le cordon du bloc d’alimentation ou la che est endommagé, lorsqu’un liquide a été renversé ou que des objets sont tombés dans l’appareil, lorsque l’appareil a
été exposé à la pluie ou à l’humidité, lorsqu’il ne fonctionne pas normalement ou lorsqu’il est tombé.
15. Aucune source de amme nue, comme des bougies allumées, ne doit être placée sur l’appareil
16. AVERTISSEMENT : Pour réduire les risques d’incendie ou de choc électrique, n’exposez pas cet appareil à la pluie ni à l’humidité. L’appareil ne doit pas être exposé à
des gouttes ou des éclaboussures et des objets remplis de liquide, comme des vases, ne doivent pas être placés sur l’appareil.
17. AVERTISSEMENT : La che secteur / le prolongateur utilisé comme dispositif de débranchement doit rester facilement accessible.
18. AVERTISSEMENT : Un appareil avec un câble de classe I (un cordon d’alimentation secteur CA à trois ls) doit être connecté à une prise de courant
avec une mise à la terre de protection.
19. Mise au rebut correcte de ce produit. Cette étiquette indique que ce produit ne doit pas être éliminé avec d’autres déchets ménagers dans tous les
pays de l’UE. An de prévenir d’éventuels dommages à l’environnement ou à la santé humaine résultant d’une élimination incontrôlée des déchets,
recyclez-les de manière responsable pour promouvoir la réutilisation durable des ressources matérielles. Pour retourner votre appareil usagé, veuillez
utiliser les systèmes de retour et de collecte ou contactez le revendeur auprès duquel le produit a été acheté. Ils peuvent prendre ce produit pour un
recyclage écologique.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
The lightning ash with arrowhead symbol within an
equilateral triangle is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure, that may be insufcient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user of the presence of important
operating and maintenance (servicing) instructions in
the literature accompanying the appliance.
MISE EN GARDE
RISQUE DE CHOC ÉLECTRIQUE
NE PAS OUVRIR
ATTENTION : POUR RÉDUIRE LE RISQUE DE CHOC ÉLECTRIQUE, NE
RETIREZ PAS LE COUVERCLE (OU L’ARRIÈRE)
AUCUNE PIÈCE RÉPARABLE PAR L’UTILISATEUR À L’INTÉRIEUR
CONFIEZ LES RÉPARATIONS À DES RÉPARATEURS QUALIFIÉS
Le triangle équilatéral contenant un éclair terminé par
une èche est destiné à alerter l’utilisateur de la
présence d’une « tension dangereuse » non isolée
dans le boîtier du produit et dont l’ampleur peut être
sufsante pour constituer un risque de choc électrique
pour les personnes.
Le point d’exclamation dans un triangle équilatéral est
destiné à alerter l’utilisateur de la présence d’instructions
importantes de fonctionnement et d’entretien dans la
documentation accompagnant l’appareil.

Nortek Security & Control LLC
4
unpaCkIng
Your subwoofer should reach you in perfect condition. If you notice any
shipping damage, please contact your Dealer immediately.
Gently lift the unit out, and remove all the packing material. It's important to
save all the packing materials and the box in case your subwoofer ever needs
to be moved or returned.
Care
To maintain the speaker cabinet’s nish, rst unplug the power cord and then
use a soft cloth to clean the surfaces. If your subwoofer needs servicing,
please read the Warranty section, page 12. If a problem persists, contact your
nearest authorized Dealer.
amplIfIer panel feaTures
ON-AUTO-OFF
LFE
R L
AC 100-120V / AC 220-240V
50-60Hz 720W
POWER
100-120V
220-240V
OFF
ON
USB POWER
5V 500mA
USB
180º 0º
50Hz 160Hz
PHASE
CROSSOVER
0 10
VOLUME
STATUS
OPTIONAL WIRELESS
RECEIVER
Low
Level
In
❹
❷
❸
❺ ❻
❶

Nortek Security & Control LLC
5
1. Power Indicator. This light is illuminated blue when the subwoofer is
turned on and playing, and it illuminates red when the subwoofer is in on,
but in Standby mode.
2. Volume Control. Volume control gives the ability to match the output
level of the subwoofer to the level of your satellite/main speakers. The
subwoofer output will increase as this control is rotated clockwise. To
prevent damage to the subwoofer during installation, turn the volume
down before turning on your subwoofer.
3. Crossover. This controls the crossover frequency between 50 Hz and
160 Hz.
Set to 50 Hz - 160 Hz: the subwoofer will reproduce frequencies
below 50 Hz. Rotating the control clockwise will smoothly increase this
frequency range up to 160 Hz.
Set to LFE: If your processor does not have its own subwoofer
crossover frequency control, rotate this control until the bass sounds
natural. If the mid-bass sounds natural but you want more low bass,
turn the crossover frequency down a little, then turn the volume up
by about the same amount. This increases the low-bass output while
leaving the mid-bass output the same.
4. Turn-on Mode Switch. In addition to the master Power Rocker Switch,
the subwoofer has 3 additional Turn-On modes.
a. When the switch is set to ON, the subwoofer will remain powered on
and will not turn off when audio signal disappears.
b. When the switch is set to AUTO, after approximately 15 minutes with
no signal, the subwoofer will enter Standby mode. It will turn back on
when an audio signal is detected.
c. When the switch is in the OFF position, the subwoofer will not turn on,
regardless of the Power Rocker Switch position.
5. Power Rocker Switch. Press the top of this rocker switch to turn the
subwoofer's master power ON or OFF.
6. Voltage Selection Switch. This switch is used to select the compatible
electrical voltage for the installation location. Please check with your local
electrical requirements before making changes to this setting.
7. Phase. This controls the relative phase of the subwoofer with respect to
your other speakers. Use this to help blend the subwoofer with the rest of
the system.

Nortek Security & Control LLC
6
Flip the switch, and listen for the most bass at your listening position. As
a nal trim, adjust the crossover frequency and volume controls after the
phase control has been set.
8. Low-Level Inputs. These connect with RCA type cables from the line-
level outputs of your receiver or preamp.
Examples:
If your processor or receiver has a single subwoofer output, connect it to
the subwoofer’s LFE input connector (see next page).
If your processor or receiver has stereo line-level output, connect it to the
subwoofer’s red and white Low Level “IN” connectors.
ON-AUTO-OFF
LFE
R L
AC 100-120V / AC 220-240V
50-60Hz 720W
POWER
100-120V
220-240V
OFF
ON
USB POWER
5V 500mA
USB
180º 0º
50Hz 160Hz
PHASE
CROSSOVER
0 10
VOLUME
STATUS
OPTIONAL WIRELESS
RECEIVER
Low
Level
In
❽
❾
❼➓
12
11

Nortek Security & Control LLC
7
9. USB Connector. The USB connector is used to power the optional
subwoofer wireless receiver. Do not plug in other USB devices into
this port, as it may damage the subwoofer or the device. Refer to the
wireless receiver installation instructions for more details.
10. Mounting Standoffs. The mounting standoffs are used to mount the
optional subwoofer wireless receiver. Refer to the wireless receiver
installation instructions for more details.
11. IEC Power Connector. The subwoofer comes with a detachable line cord
that attaches here. Make sure it is rmly pushed into place. Connect the
other end to a properly congured AC outlet designed for the type of plug
with the correct voltage for your model.
12. AC Line Fuse. The subwoofer is supplied with a conservative slow-blow
type fuse to protect the electronics. If this fuse fails, replace it with the
exact same type and current rating for your local AC voltage. This rating
is marked on the control panel near the fuse holder.
NOTE: Always unplug the power cord from your AC outlet before
removing the fuse. To replace or inspect the fuse, use a small
athead screwdriver to gently pry out the fuse carrier and fuse.
subwoofer plaCemenT
Subwoofer placement can greatly inuence its performance. All rooms are
different, but the loudest output will likely occur if the subwoofer is placed
in a corner of the room on the same wall as the front channel speakers. You
may need to experiment with more than one location, always testing the
sound from the primary listening position until you nd the right balance and
consistency in the bass performance.

Nortek Security & Control LLC
8
ConneCTIng your subwoofer (lfe)
If your processor or receiver has a subwoofer output (LFE/SUB), it should be
connected to the subwoofer’s LFE input as shown. This is the simplest and
recommended connection.
If you have a Home Theater processor or receiver, it likely has an independent
subwoofer volume and crossover control. If so, you should set the
subwoofer’s Volume Control to 12 o’clock, the Crossover to 160Hz/LFE, and
use the processor’s subwoofer level and frequency controls for adjustments.
AUDIO
OUTPUT
2 CH INPUT
SPEAKERS
CLASS 2 WIRING
AUDIO VIDEO
MAIN
MAIN
TUNER
DIGITAL
INPUT
R L
A
B
+
+
––
+
–
RCENTER L
R
CD DVD
CBL
AM
ANT
FM
ANT
GND
COAXIL
MONITOR
OUT
(LFE)
SUB
WOOFER
AUX
IN
MD/
CDR
IN
OPTICAL
OUT
OUT
VCR
MAIN
GRD
DVD
CENTER
SUB
WOOFER
L
R L
REAR
SURROUND
R L
➀
➁
ON-AUTO-OFF
LFE
R L
AC 100-120V / AC 220-240V
50-60Hz 720W
POWER
100-120V
220-240V
OFF
ON
USB POWER
5V 500mA
USB
180º 0º
50Hz 160Hz
PHASE
CROSSOVER
0 10
VOLUME
STATUS
OPTIONAL WIRELESS
RECEIVER
Low
Level
In
LFE Output
SDSi Subwoofer (back)

Nortek Security & Control LLC
9
2-Channel
Amplier
LFE/
ON-AUTO-OFF
LFE
R L
AC 100-120V / AC 220-240V
50-60Hz 720W
POWER
100-120V
220-240V
OFF
ON
USB POWER
5V 500mA
USB
180º 0º
50Hz 160Hz
PHASE
CROSSOVER
0 10
VOLUME
STATUS
OPTIONAL WIRELESS
RECEIVER
Low
Level
In
Stereo Output
SDSi Subwoofer (back)
If your processor or receiver does not have a LFE/SUB output, but has a
Stereo Output, you can connect a stereo RCA type cable from the stereo
output to the Low Level red and white inputs on the back on the subwoofer.
You can also use the optional subwoofer wireless receiver to send audio
from your source to the subwoofer. Refer to the wireless receiver installation
instructions for more details.
ConneCTIng your subwoofer (sTereo)

Nortek Security & Control LLC
10
adjusTIng your subwoofer
1. Set the MODE switch to the ‘ON’ position.
2. Plug the subwoofer into an electrical outlet using the included power
cord. The status LED will illuminate solid blue when power is present and
the subwoofer is ON.
3. Set the controls and switches to their initial setup
positions:
a. VOLUME: dial set to 50%, or 12 o’clock
b. CROSSOVER dial: Set to LFE (if LFE input is used).
Otherwise, set it to match the low-end frequency limit
of the satellite speakers in use. (See specications
for the speakers installed to determine their low-end
limit.)
c. PHASE: Set to 0
4. Play a movie scene or music track and set the system volume to an
average level. Listen to the bass level from your favorite listening position.
Adjust the VOLUME control as desired.
5. Continue listening to your favorite music and movie sources using the
settings chosen for volume and crossover.
6. Experiment with the PHASE setting until you nd the best setting for the
installation. Depending on your subwoofer’s placement, the bass may
sound louder or deeper when the phase has been optimized. In some
cases, adjusting phase will make no audible difference.
7. Once calibration is complete, switch the power mode back to ‘AUTO’ if
Auto Sense mode is being used.
ON-AUTO-OFF
LFE
R L
AC 100-120V / AC 220-240V
50-60Hz 720W
POWER
100-120V
220-240V
OFF
ON
USB POWER
5V 500mA
USB
180º 0º
50Hz 160Hz
PHASE
CROSSOVER
0 10
VOLUME
STATUS
OPTIONAL WIRELESS
RECEIVER
Low
Level
In

Nortek Security & Control LLC
11
aTTenTIon: Toour Valued CusTomers
To insure that consumers obtain quality pre-sale and after-sale support
and service, products are sold exclusively through authorized dealers. This
warranty is VOID if the products have been purchased from an unauthorized
dealer.
Nortek Security & Control offers a variety of accessories to make your
installation of this and other products easy, economical, and professional. To
learn more about our products, technologies and specications, go to: www.
nortekcontrol.com or contact your authorized Dealer for more information. For
technical inquiries, please call 1-800-448-0976.
In our attempt to constantly improve our products, features and specications
are subject to change without notice.
speCIfICaTIons
SDSi-8
Woofer 8” High-excursion Polypropylene Cone
Passive Woofers Dual 8” High-excursion Polypropylene Cone
Frequency Response (+/– 3dB): 29 – 160HZ
Amplier Power (Peak) 400 Watts
Crossover Frequency 50-160Hz
Dimensions (L x W x H) mm / inches 298 x 316 x 317 / 11.73 x 12.44 x 12.48
Voltage 100-120VAC / 220-240VAC Selectable
SDSi-10
Woofer 10” High-excursion Polypropylene Cone
Passive Woofers Dual 10” High-excursion Polypropylene Cone
Frequency Response (+/– 3dB): 26 – 160HZ
Amplier Power (Peak) 500 Watts
Crossover Frequency 50-160Hz
Dimensions (L x W x H) mm / inches 334 x 351 x 353 / 13.15 x 13.87 x 13.9
Voltage 100-120VAC / 220-240VAC Selectable
SDSi-12
Woofer 12” High-excursion Polypropylene Cone
Passive Woofers Dual 12” High-excursion Polypropylene Cone
Frequency Response (+/– 3dB): 24 – 160HZ
Amplier Power (Peak) 600 Watts
Crossover Frequency 50-160Hz
Dimensions 375 x 393 x 394 / 14.75 x 15.46 x 15.5
Voltage 100-120VAC / 220-240VAC Selectable
SDSi-15
Woofer 15” High-excursion Polypropylene Cone
Passive Woofers Dual 15” High-excursion Polypropylene Cone
Frequency Response (+/– 3dB): 19 – 160HZ
Amplier Power (Peak) 1000 Watts
Crossover Frequency 50-160Hz
Dimensions (L x W x H) mm / inches 483 x 508 x 502 / 19 x 20 x 19.75
Voltage 100-120VAC / 220-240VAC Selectable

Nortek Security & Control LLC
12
lImITed 2-year warranTy
Nortek Security & Control, LLC (“Nortek Security & Control”) warrants to the original retail purchaser only that this product will be free of
manufacturing defects in material and workmanship for the following periods and subject to the limitations and exclusions set forth below:
2-Year Warranty
This warranty is not transferable to subsequent purchasers of the product. To obtain warranty service, contact the authorized dealer where you
purchased your product or take the unit to the nearest authorized dealer (with proof of purchase – claims made without proof of purchase will be
denied) who will test the product and if necessary, forward it to Nortek Security & Control for service. If there are no authorized Dealers in your area,
please contact Nortek Security & Control to receive a factory Return Authorization Number. DO NOT RETURN ANY UNIT WITHOUT FIRST RECEIVING
WRITTEN AUTHORIZATION AND SHIPPING INSTRUCTIONS FROM Nortek Security & Control.
Upon examination, Nortek Security & Control will, at its sole option and expense, repair or replace any product found to be defective. Nortek Security
& Control will return the repaired or replaced unit to you via its usual shipping method from the factory or repair center to your address in the
United States of America or Canada only. Any shipping costs for addresses outside of the United States or Canada shall be the responsibility of the
purchaser. In the event that this model is no longer available and cannot be repaired effectively, Nortek Security & Control, at its sole option, may
replace it with a different model of equal or greater value, or refund the original purchase price paid.
THE FOREGOING ARE YOUR EXCLUSIVE REMEDIES FOR BREACH OF WARRANTY.
This Warranty does not include service or parts to repair damage caused by improper use or handling, including but not limited to damage caused by
accident, mishandling, improper installation, commercial use, abuse, negligence, or any defect caused by repair to the product by anyone other than
Core Brands. This warranty does not cover reimbursement for your costs of removing and transporting the product for warranty service evaluation, or
installation of any replacement product provided under this warranty.
This Warranty will be void if:
- The Serial Number on the product has been removed, tampered with or defaced.
- The product was not purchased from an authorized dealer or reseller.
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES.
NORTEK SECURITY & CONTROL EXPRESSLY DISCLAIMS ALL SUCH OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT, WITH RESPECT TO THE PRODUCT. TO THE MAXIMUM EXTENT
PERMITTED BY LAW, NORTEK SECURITY & CONTROL SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES EXCEPT TO
THE EXTENT PROVIDED (OR PROHIBITED) BY APPLICABLE LAW, EVEN IF NORTEK SECURITY & CONTROL HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES.
Notwithstanding the above, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, or applicable state laws, then you may be
entitled to any implied warranties allowed by law for the Warranty Period. Further, some states do not allow limitations on how long an implied
warranty lasts or allow the exclusion or limitation of consequential damages, so such limitations may not apply to you. This warranty gives you
specic legal rights, and you may also have other rights which vary from state to state.
For the name of your nearest authorized dealer, contact: Nortek Security & Control, 5919 Sea Otter Place, Suite 100 Carlsbad, CA 92010, or call (800)
472-5555 or [phone].
With regard to sales over the Internet, please be advised that Nortek Security & Control only sells products through a select group of authorized
Internet Resellers. Products offered on the Internet through unauthorized Internet dealers are not covered by Nortek Security & Control.
1. Goods acquired on a secondary or gray market
2. Counterfeit or stolen goods
3. Damaged, or defective goods
Please ll in your product information and retain for your records.
Model ______________________________________________
Serial # _____________________________________________
Purchase Date ________________________________________
10030692 Rev-B
www.speakercraft.com
©2020 Nortek Security & Control LLC. All rights reserved. SpeakerCraft is a
registered trademark of Nortek Security & Control LLC.