Speakman ANYSTREAM VS-3014 Guide

1/11
92-3183
Rev. 2
SPEAKMAN®
PO Box 191 Wilmington, DE 19899 Phone: [phone] Fax: [phone]
Visit us on the web at www.speakmancompany.com
SPEAKMAN COMPANY
VS-3014 Installation, Operation & Maintenance Instructions
ANYSTREAM ® HAND-HELD SHOWER
DESCRIPTION
Polished chrome plated ANYSTREAM®S-3014 hand shower. Includes a five foot long hose and swivel ball bracket
for shower arm mounting. Spray adjusting, 3-3/4” outer ring. 5 plunger nozzles resist scale build-up and provide 45
spray streams for a full body coverage pattern. Center core nozzle delivers a massage spray. Combination spray
included. Water conserving pressure compensating AUTOFLO® device reduces flow to 2.5 GPM/9.46LPM
maximum, to meet existing ASME A112.18.1 Standard. ½” NPT inlet.
SPECIFICATIONS
SUPPLY INLET: ½” NPT
FLOW RATE: 2.5 GPM/9.46LPM MAXIMUM
FLOW CONTROL: VARIABLE
SHIPPING WEIGHT: 1.43 LBS.
INSTALLATION
Screw the swivel arm bracket onto the outlet shower arm. Install rubber washers in the ends of the hose. Turning
in a clockwise direction, thread the hose swivel onto the threaded end of the swivel arm bracket and the other hose
end onto the hand held shower. IMPORTANT: One end of the hose is marked with ribs and a paper tab
indicating this end MUST connect to the bracket. If not installed correctly there will be restricted flow. Hand
tighten firmly all connections. Turn the water supply on and check for leaks.
OPERATION
To adjust the spray pattern of the shower head, simply rotate the outer ring to the desired spray (Full-Body, Dual
action or Massage). The outer ring can rotate 360°.
MAINTENANCE
BN – Brushed Nickel
VS-3014-E2 – Low Flow Showerhead
(2.0 GPM/ 7.6 LPM)
VS-3014-BN-E2 – Low Flow Brushed
Nickel Showerhead
(2.0 GPM/ 7.6 LPM)
Product improvements may cause
specification and dimensional
changes without notice.
The gleaming finish of your
SPEAKMAN®hand shower can be
cleaned by using mild soap and
warm water. Dry immediately with
a soft, clean cloth for best results.
The flow control device limits water
flow to 2.5 gallons per minute. The
small orifices may become
clogged with scale and other
minerals found in potable water.
To clean the flow regulator, simply
remove the shower arm mount
from the bent arm, pull out the
rubber washer from the ball,
dislodge the flow regulator and
clean as necessary.
OPTIONS
Note: Accessories shown.
ROUGH-IN MEASUREMENTS

Size (B5) : 257mm(w) x 182mm(h)
Installation
1. Hold the Grab/Slide bar against the wall in the chosen location. Using a pencil, mark the drill hole positions
(4 in total) for the lower and upper mounting brackets. If using as a Grab bar, be sure to fasten securely to
a wall stud. (Note: upper mounting bracket height is adjustable)
2. To mount the brackets, use a No. 10 (0.1935 inches/5.5 mm) masonry drill bit to make a hole approximately
1 3/8 inches (35 mm) deep. Push the plastic anchors (4 in total) into the drilled holes, unless your mounting
to wall studs, where anchors can be omitted. (Note: plastic anchors provided may not be suitable for all
types of wall construction, seek professional help if in doubt)
3. Fix upper mounting bracket and then the lower mounting bracket to the wall using the four (4) screws
provided.
4. Push the bracket covers over the mounting brackets while paying close attention to cover orientation for
proper placement.
Clean Grab/Slide bar regularly using a non-abrasive liquid bathroom cleaner.
VS-153-ADA
Bracket
Inner Sections
1
2
3
2
4
92-3105-R1 3/26/10