Speakman SE-8000 User manual

SPEAKMAN EMERGENCY TANK SHOWER | SE-8000
Options
Emergency 528 gallon (2000L)
Gravity-Fed Tank Shower and Eyewash
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
Alarm System for both
Shower and Eyewash
Water Collection Bund
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
Treadle plate activator
for main shower
se-8000 (options) Features
Treadle plate Shower Head
activator for
main shower
(optional)
(ts-treadle)
Water
collection
bund
(optional)
(ts-bund)
Eyewash with
stainless steel
bowl
(optional)
(ts-sseyewash)
Eyewash with
Privacy
screens (3)
sides
(optional)
(ts-screens)
Digital water level
& water temperature
gauge
(optional)
(ts-gauge)
Alarm system
for both shower
& eyewash
(optional)
(ts-alarm)
Stainless steel
support
frame
(optional)
(ts-sssupport)
ts-treadle treadle plate activator
for main showerts-sssupport stainless steel support frame
ts-bund water collection bund ts-gauge digital water level & water
te mperature gauge
ts-sseyewasheyewash with stainless steel bowl ts-alarm alarm system for both
shower & eyewash
ts-screens privacy screens (3) sides
230V, Single Phase, 50/60Hz
Stainless Steel
Support Frame
Eyewash with Stainless
Steel Bowl (not shown)
Privacy Screens (3) Sides
(not shown)
Digital Water Lever and
Water Temperature Gauge
528 gallon
capacity tank
Elevated
drain
Integrated
eyewash
Emergency
shower
For use in indoor and outdoor non-hazardous
locations.
Rotationally molded polyethylene, water tank is
covered in 1-1/2” reflective rigid polyurethane foam,
insulation board and tank structure is futher
protected by a shroud complete with warning signs.
528 gallon (2000L) overhead insulated tank is fitted
with a 3kw immersion heater with high temperature
cuto to prevent overheating conditions.
5w/ft. heating cable protects internal piping from
freezing conditions for both shower and eyewash.
PIR controlled downlight in shower area, and all the
electronics required to incorporate these and other
electrical optional features such as:
• Digital Display Gauge which indicates water level
and water temperature data (option)
• Visual/audio alarm beacon (option)
The power supply hook up to the electrical system
shall be 240 volt, single phase, 50/60Hz.

EMERGENCY TANK SHOWER TRAINING | PG. 2
SPECIFICATIONS
Features
EYE/FACE WASH FEATURES:
• Yellow Plastic Bowl
• (2) yellow plastic spray outlets with flip-top dust caps
• ½” NPT female brass, chrome-plated, full flow stay-open
ball valve
• Stainless steel push handle activator
SHOWER FEATURES:
• Insulated 528 gallon (2000 ltr) Polyethylene Tank
• Support frame constructed from 1-1/2 x 1-1/2 x 1/8 hot dipped
galvanized tubular steel, with fixed bolt down brackets
• Ø10-1/4” stainless steel shower head
• 1-1/2” NPT female stainless steel full flow ball valve, activated
by yellow steel Push Bar
• Mechanical water level gauge
• 1” NPT water fill inlet, with valve and ball float for automatic
shuto when tank is full
• 1” NPT water overflow outlet
• 240 Volt, Single Phase, 50/60Hz, 13.88 Amps
• 3kw Immersion Heater that will maintain an approximate
water temperature of 86° F at an ambient temperature of 14 °F.
• Heat Tracing for Shower and Eyewash Piping
• PIR Sensor and Area Downlight
• Thermal cuto to shuto electrical power to prevent
overheating conditions
• Universal emergency signage
• Weights:
• 1598 lbs. (un-filled)
• 6004 lbs. (filled)
OPTIONS:
❑TS-TREADLE
Treadle plate activator for main shower
❑TS-BUND
Water Collection Bund
❑TS-SSEYEWASH
Eyewash with Stainless Steel Bowl
❑TS-SCREENS
Privacy Screens (3) Sides
❑TS-SSSUPPORT
Stainless Steel Support Frame
❑TS-GAUGE
Digital Water Lever and Water Temperature Gauge
❑TS-ALARM
Alarm System for both Shower and Eyewash
COMPLIANCE:
• Complies to ANSI/ISEA Z358.1
• Constructed using UL Approved Electrical Components
WARRANTY:
• 3 year (general mechanical) limited
• 1 year (electrical equipment) limited
1413
3897
1470
Plan
Front Elevation
NOTE: 1. All dimensions are in inches (millimeters) unless
otherwise specified and are subject to change without notice.

EMERGENCY TANK SHOWER TRAINING | PG. 3
COMPETITIVE ANALYSIS OF KEY FEATURES
Competition
Brand Image SKU Capacity Structure material Standard Equipment Certification
Haws 8770 430 gallons 1628 L Stainless Steel pipe,
fiberglass tank, bronze
valves
Shower head + Eye/face
wash standard,
water-proof side panels
CSA
Hughes EXP-MH-14K/
1200-GALVZ12
320 gallons 1200 L uPVC pipe, high-density
polyethylene tank, uPVC
shower valve, stainless
steel eye wash valve
Shower head + eye/face
wash
ANSI/ISEA Z358.1-2009
Guardian G4710 400 gallons 1514 L Stainless steel frame/tank/
ball valves
Shower head + eye/face
wash
CSA
FSI F-SS1RT-L2000 528 gallons
2000 L
Stainless steel frame/tank Shower head + eye/face
wash, panic bar
ANSI/ISEA Z358.1-1998
Speakman SE-8000 528 gallons
2000 L
Rotationally molded
polyethylene, water tank
covered in 1-1/2” reflective
rigid polyurethane foam,
insulation board tank
structure is protected by a
plastic shroud
Shower head + eyewash,
panic bar
ANSI/ISEA Z358.1
UL Approved Electrical
Components

EMERGENCY TANK SHOWER TRAINING | PG. 4
INSTALLATION
How to install
SE-8000
Determine final mounting position per all
OSHA, ANSI/ISEA Z358.1 requirements.
• This area should be well lit, and the area
around and underneath the equipment
needs to have proper drainage to ensure
there is no standing water left after
activation.
• It’s also important to understand the
eects any water/overspray and or diluted
chemicals could have on equipment in the
same area, especially electrical items.
• Proper drainage of unit should follow
all associated local, county, and national
standards.
NOTE: unit is shipped fully assembled,
except for (2) side modesty panels
(If supplied).
Disconnect all temporary shipping
brackets that are holding the unit in place.
NOTE: After removal of support
bracketing, if drain sump pan is included
proceed to step #5, if not proceed to
step #7.
Place crated SE-8000 Tank Shower as
close to final location as possible.
• Leaving enough maneuvering area for
crane or suitably high and stable fork
truck being used to safely hoist the unit
from the shipping crate base.
Remove top and side panels of shipping
crate.
INSTRUCTIONS FOR MODEL TOOLS AND SUPPLIES
Crane Forklift
Philips
Screwdriver
Drill
IMPORTANT
WARRANTY
NEED HELP?
• Be sure to read instructions throughly before
beginning installation.
• It is the responsibility of the installer to ensure
all installation of electrical equipment is per-
formed by suitably qualified personnel. Failure
to do so can result in injury or death.
• The Tank Shower should only be supplied
from a potable water supply. See Cleaning &
Maintenance section located in this document
regarding inspection and water quality.
• To ensure a full 15 minutes of operation, be sure
to refill the tank to full capacity every time the
shower or eyewash is activated.
3 year (general mechanical) limited /
1 year (electrical equipment) limited
For additional assistance or service please
contact:
SPEAKMAN® Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
customerservic[email protected]
www.speakman.com
1 4
2
3
Temporary shipping
bracket top and
bottom of tank
shower.
Typical temporary
hold down brackets.
Typical temporary hold down brackets.
or
or

EMERGENCY TANK SHOWER TRAINING | PG. 5
INSTALLATION
How to install
The Water collection bund is sent
attached to bottom of the Tank Shower.
Disconnect, remove and locate and install/
mount Water collection bund into final
desired position, on suitable concrete
foundation. Secure using suitable
mounting hardware at all (4) mounting
tab locations.
NOTE: This surface shall be flat/level and
suitable to support the weight of the unit
with a full tank of water (minimum 6000
lbs. total).
Orient and install unit in final desired
position either on Water collection bund
(if supplied) or on suitable concrete
foundation, and secure using suitable
mounting hardware at all (4) mounting
tab locations.
NOTE: This surface shall be flat/level and
suitable to support the weight of the unit
with a full tank of water (minimum 6000
lbs. total).
Connect desired drain piping to outlet
of Water collection bund following all
applicable local, state, and national
plumbing codes.
Remove all “lifting” braces located at top
of unit and inside the shower area, along
ceiling. Save all bracing for future use.
Remove strap ties holding foot treadle in
place, if supplied.
Using suitable lifting apparatus (crane,
etc.) and rigging, properly attach rigging
to lifting mounts at the top of the unit
near the tank lid, and carefully stand unit
upright. Ensure the center of the unit is
directly under the lifting apparatus at
all times, until vertical. Watch for unit to
swing slightly when lifted from floor. NOTE: The tank shower is also supplied
with forklift truck “lifting” braces, located
inside the showering area, just below the
inner ceiling area for easy vertical upright
lifting using forks from a lift crane or fork
truck.
Disconnect all temporary shipping
brackets that are holding the unit in place.
NOTE: After removal of support bracket-
ing, if drain sump pan is included proceed
to step #5, if not proceed To step #7.
5 8
6
9
10
7
Outlet
Typical shipping hold down brackets.
Lift bracing located in shower area,
near ceiling.

EMERGENCY TANK SHOWER TRAINING | PG. 6
INSTALLATION
How to install
OPTIONAL: The Alarm is mounted and
shipped, so that the light faces towards
the inside of the shower area. The light
needs to be removed and fl ipped so it
rests outside the shower.
Connect drainage plumbing (if desired) to
the tank over-flow outlet, located in the
back of the unit.
The Tank Shower requires connection
to a 240 volt, single phase, 50/60Hz
electrical supply, to run the immersion
heater and all other electrical components.
Any electrical options you have specified
should be supplied through a minimum
30mA Ground Fault Protection Device
(GFPD).
NOTE: It is the responsibility of the
installer to ensure all installation of
electrical equipment is performed by
suitably qualified personnel. Failure to
do so can result in injury or death.
The electrical equipment fitted to the Tank
Shower is connected to a suitable
miniature circuit breaker for the water
heater, lighting, trace heating and alarm
system as necessary. If an alarm system is
fitted, then a junction box is also fitted in
the void of the ceiling space at the front of
the shower. The junction boxes are
accessible via a removable hatch in the
ceiling. If remote alarm monitoring is
required, then a 7 core 1mm SY type cable
is also brought out to the rear of the Tank
Shower for connection to the building
Building automation system. Connections
are Hot, Neutral and Ground, with a Single
Phase supply of either 50Hz or 60Hz,
240Volts.
Connect potable water supply to water
inlet located in the back of the unit. When
the tank reaches full capacity the Ballcock
fill valve, located inside the tank will shut
o the supply automatically. The main
water supply to the tank shower should be
turned o once filling
is complete.
WATER SUPPLY: The Tank Shower should
only be supplied from a potable water
supply. See Cleaning & Maintenance
section located in this document
regarding inspection and water quality.
NOTE: To ensure a full 15 minutes of
operation, be sure to refill the tank to
full capacity every time the shower or
eyewash Is activated.
Visual and audible alarms are available to
provide a warning when the shower or
eyewash has been activated, or to indicate
changes in the water temperature/levels.
• The temperature alarm is activated by a
temperature probe inside the shower and is
connected to the graphic display or a signal
conditioning relay if no graphic display is
used.
• The water level alarm is monitored by a level
transducer fi tted to the bottom of the tank
and the alarm sound when the level drops
either by usage or testing. The signal from
the transducer is connected to the graphic
display or a signal conditioning relay if no
display is used.
• The eyewash alarm is activated by means of
a tilt switch fi tted to the operating paddle.
• The local sounder/strobe alarm will sound
for 30 minutes before it automatically
switches itself o , the strobe light however
will continue to fl ash while an alarm
condition still exists.
11 1412
13
Shown flipped inside for
shipping.
Unit is supplied standard with mechanical
style visual water level indicator located
on the front of the shroud face. This level
indicator is operated mechanically by a
ball float inside the water tank.
Remote
alarm from low
voltage
enclosure
Main electrical inlet single phase 230
volt 3.055Kw 4kva
Remote alarm
Core 1 cannon
Core 2 n/o low alarm
Core 3 n/o high alarm
Core 4-7 spare
Remove screws and flip to mount alarm,
using same holes, so light is outside the
shower area.
Main supply
isolator on rear
panel

EMERGENCY TANK SHOWER TRAINING | PG. 7
OPERATION
How to operate the tank shower
• When installing a Tank Shower it is
important to remember to allow time for
the water to reach the correct
temperature before use. Emergency
Safety Shower, Eye wash water
temperatures must never exceed 100°F
or drop below 60°F.
• Activation of a Tank Shower is by way
of a yellow push bar that extends across
the full width of the rear framework. This
opens the stay-open valve. Unit can also
be activated by a person other than the
contaminated person, by using the same
yellow push bar which extends beyond the
shower area on the right hand side.
• Once activated the valve will remain
open until it is physically shut by pulling
the bar upwards.
• The eyewash is activated by way of a
push paddle which is located to the side
of the eyewash unit. Once activated, the
valve will remain open until physically
shut o by pulling the paddle back to the
upright position.
• If the unit has been fi tted with an
optional treadle plate the water supply will
be activated as user steps on to it.
OPTIONAL: The graphic display screen
shows the water level with a digital “dial”
display and a numeric digital read out with
the gallons remaining in the tank.
The temperature is also shown with a
digital “dial” display and a numeric digital
readout in Fahrenheit.
The alarm conditions are as follows:
1. When the water level drops below a
critical level, the local alarm will sound
and a WATER DROPLET appears on the
display screen, if the remote alarm option
is included then a volt free signal is also
activated. To reset the alarm the tank must
be re-filled.
2. When the temperature drops below 65
degrees Fahrenheit the local alarm will
sound and a BLUE SNOWFLAKE appears
on the display screen, if the remote alarm
option is included then a volt free signal is
also activated.
3. When the water temperature goes
above 90 degrees Fahrenheit the local
alarm will sound and a RED SNOWFLAKE
appears on the display screen, if remote
alarm option is included then a volt free
signal is also activated.
Whenever an alarm condition, high or
low, exists an image of a RINGING BELL
appears on the display screen.
The eyewash alarm is turned on when
water flow is detected through the
eyewash and the local sounder/strobe unit
will activate, if the remote alarm option
is included then a volt free signal is also
activated.
The eyewash alarm is not a part of the
graphic display and will not turn on any
icons until the water level drops to a
critical level.
The local alarm sounder/beacon has a
built in 30 minute timer that shuts the
alarm sound o however the strobe will
continue to flash until the alarm condition
has been removed, by resetting the
system by re-filling tank, and allowing
water temperatures to reach acceptable
range.
1 2
Blue
Blue
Red
Bell
Optional digital
display gauge
on front of unit
NOTE: The Display pictured is for
reference only.

EMERGENCY TANK SHOWER TRAINING | PG. 8
Rough-in
ROUGH-IN
8
119mm
5"
4
3"
C
L
TO
4
C
L
1543mm
"
8
1470mm
7
57
60
"
8
1583mm
62
3
5"
C
L
TO
8
C
L
1413mm
"
4
55
1
1580mm
62
15
8"
40mm
TYP.
BACK RIGHT
TOP
TFELTNORF
43 1
8"
1097mm
STROBE
ALARM
(Option)
Activation Push Handle
Walk-On Treadle
LEVEL GAUGE
MECHANICAL WATER
GAUGE (Option)
DIGITAL DISPLAY
Activation (Option)
GRADE
2
" 83 1
2120mm
7"
8
7
200mm
153 3
8"
3897mm
ACCESS HATCH
B
B
A
A
Modesty (3) Panels
(Option)
1" NPT Water
Supply Inlet
Power Supply Inlet
230V, Single Phase, 50/60Hz
Water Outlet
1" NPT Over-Flow
1-1/2" NPT Sump Catchment
Drain Outlet (Optional)
B-BNOITCES
A-ANOITCES

EMERGENCY TANK SHOWER TRAINING | PG. 9
PERIODIC CLEANING AND MAINTENANCE
KEYS FOR BEST PRODUCT PERFORMANCE
The time frame for changing the water in the tank will vary depending on
the quality of the water, and the surrounding environmental conditions.
Per ANSI/ISEA Z358.1 the tank shower “shall be visually checked weekly
to determine if flushing fluid needs to be changed or supplemented. Such
inspection shall be conducted in accordance with manufacturer’s
instructions”. Furthermore, Speakman suggests that the unit should be
tested at least once a week to check for optimum performance, and
document data to record results for maximum eciency.
Note: After each activation (including maintenance), the tank should be
refilled to ensure it is full and ready for use.
Frequent analysis of the water quality within the unit is recommended to
ensure there is no build-up of harmful bacteria. If you are using a water
treatment supplement such as EndoSanTM, please do so in accordance with
all the manufacturer’s recommendations and instructions.

EMERGENCY TANK SHOWER TRAINING | PG. 10
TROUBLESHOOTING GUIDE
Before calling Speakman Company for
service, please run through the following
checklist of troubleshooting steps.
NOTE: Before trouble shooting any potential issues, confirm the unit has
been properly installed following all the supplied SE-8000 Installation
Instructions.
No water flows from the Shower or Eyewash
1. Confirm the tank is full of potable water.
Tank fails to fill with water via the inlet pipework.
1. Check inlet ball valve float has not stuck in the full/o position.
2. Check to make sure inlet fill pipe is not blocked.
Tank continually over flows
1. Check inlet ball valve float has not been detached from its operating rod,
or has been punctured, causing valve to be stuck in the open position.
2. Check to make sure overflow outlet piping is not blocked, causing water
to overflow out of tank, from under Tank Lid.
Eyewash Spray Heads producing inadequate water flow in one or both
Spray Heads
1. Confirm there is a full amount of potable water in tank.
2. Check for debris inside the nozzles by unscrewing each nozzle in a count-
er-clockwise direction to unscrew from the eyewash bullhorn. Clean out and
replace.
Main overhead shower head spray pattern is irregular and flow pattern is
not full.
1. Confirm there is a full amount of potable water in tank.
2. Check for debris inside shower head by removing the small screws on the
perforated spray face and clean out any debris that may be present. Replace
spray face in reverse order.
PIR activate Light not working and replacement of the Light Bulb
1. Pull bae or reflector out of the trim. It may be necessary to insert a small
screwdriver between the bae and the optic holder to pry it free. (fig 14).
Twist the black Bulb holder counter clockwise to remove optic and holder
(fig 15)
2. Remove Bulb from black Bulb Holder. Snap the new Bulb into the black
Bulb Holder (fig16). Align the tabs in the heatsink to the slots in the optic
holder and push optic into the fixture. Twist Bulb Holder clockwise to
secure. (fig 17).
3. Press the bae or reflector back into the fixture. Note that the bae has
depressions in it that must align with tabs on the trim ring. (fig 18)
Figure 14 Figure 15
Figure 18
Figure 17Figure 16

EMERGENCY TANK SHOWER TRAINING | PG. 11
TROUBLESHOOTING GUIDE
16. Once complete and before refitting the access hatch and showerhead
refill the tank and check for leaks. IMPORTANT, damage to the
immersion heater will occur if the heating element is turned on without
any water in the tank.
NOTE, if removal of complete ceiling is required, please contact
manufacturer for further instruction.
PIR activation Switch for Light fails to activate
1. Have fully trained electrician check and confirm the unit is properly
hooked up to, and energized with a 240 volt, single phase, 50/60 Hz electric
power supply.
2. Check PIR operation by checking the Green sensor light is illuminated
within the lens and responds to movement by flashing o and on.
i. Lights will not turn ON
a. Lens is dirty or obstructed: Inspect the lens visually and clean if
necessary, or remove the obstruction
ii. Lights will not turn OFF
a. Sensitivity set improperly: Adjust the SENSITIVITY dial.
iii. Lights turn OFF and ON too quickly
a. Sensitivity set improperly: Adjust the SENSITIVITY dial.
iv. Time delay set improperly: Adjust the TIME DELAY dial.
Water Heater not heating the water
1. Have fully trained electrician check and confirm the unit is properly
hooked up to, and energized with a 240 volt, single phase, 50/60 Hz electric
power supply.
2. Check Circuitry by a fully trained electrician by checking that the rod
thermostat is operational by testing the voltage in/out of the thermostat.
3. If no voltage is detected from the rod thermostat, remove and replace by
disconnecting supply wiring, then proceed to pull the rod thermostat out of
its tubular holder.
4. Replace with new one and re-connect and test.
5. If voltage is present at the rod thermostat, then the heater element should
be replaced. To gain free access to the heater location, the under-ceiling
panel should be removed to facilitate access. Before any attempt to remove
the heating element, the power should be isolated and locked o. The tank
should be completely emptied of water, including the small heater sump
where the Immersion Heater is located, by using whatever means necessary
(wet/dry vac, manual pump, etc.). Then the element can safely be removed
for checking and/or replacing.
Using the properly sized Box Wrench and 24” Adjustable Wrench, following
are the steps to access and remove the 3kW Immersion Heater.
1. Disconnect electric power from unit.
2. Drain as much water out the tank as possible.
3. Remove the heating element access panel.
4. Switch o the rotary isolator behind the access panel to turn o ALL
electricity to unit.
5. Remove the shower head by rotating anticlockwise.
6. Remove the heating element terminal cover.
7. Disconnect and remove the supply cable from the heating element.
8. Remove the 25mm cable gland from the element body.
9. Remove the rod thermostat and put aside for safe keeping being
careful not to disturb the setting, this will need to be fitted to the
replacement element.
10. During the next steps care needs to be taken not to damage the
transducer fitted in the sump to the left of the heating element.
11. Going through the shower head hole fit the 24 inch pipe wrench around
the brass adapter on the heating element to hold the adapter in place.
12. Going through the heating element access hatch slide the box spanner
over the heating element and unscrew the element from the brass
adapter.
13. When the heating element is removed any water left in the element
sump will pour out.
14. Reassembly is the reverse of the above steps.
15. When fitting the new heating element apply a generous coating of
sealant to the threads.
Detector
LED
FRONT VIEW
10
30
SEC MIN
TIMESENSITIVITY
FIG. 8
30
20
SIDE VIEW
1.06”
[2.7 cm]
Gasket Lock
Ring
Lens
Cover
2”
[5.0 cm]
1.5”
[3.8 cm]
3.87”
[9.82 cm]

EMERGENCY TANK SHOWER TRAINING | PG. 12
3. Adjustment Settings:
i. Time-Delay: This adjustment controls the amount of time the lights stay
ON after the last detected motion. You may select settings varying from
30 seconds, 10 minutes, 20 minutes and 30 minutes.
ii. Sensitivity: This adjustment controls the sensitivity of the passive
infrared (PIR) detection.
4. Remove the PIR switch by removing the containment screw and turn ¼
turn to release. Then remove under ceiling panel to gain free access to the
junction box in which to disconnect the wiring to the switch. Then remove
the switch and if faulty replace with a new one.
NOTE: After power is turned on, allow approximately two minutes for
charge-up. If the lights turn ON and the LED blinks when a hand is waved in
front of the lens, then the Sensor is working properly. If the operation is
dierent, refer to the Troubleshooting Section. The Sensor is factory pre-set
to work without any adjustments. If you desire to change the factory
settings, refer to the Settings section.
Water Level/Water Heater Digital Display Unit fails to illuminate.
The graphic display screen shows the water level with a dial type display
and a digital read out with the gallons remaining in the tank.
The temperature is also shown with a dial type display and a digital readout
in Fahrenheit.
The alarm conditions are as follows.
1. When the water level drops below approximately 572 gallons the local
alarm will sound and a WATER DROPLET appears on the display screen,
if the remote alarm option is included then a volt free signal is also
activated. To reset the alarm the display must read at least 575 gallons.
2. When the temperature drops below 65 degrees Fahrenheit the local
alarm will sound and a BLUE snowflake appears on the display screen,
if the remote alarm option is included then a volt free signal is also
activated.
3. When the water temperature goes above 90 degrees Fahrenheit the
local alarm will sound and a RED snowflake appears on the display
screen, if the remote alarm option is included then a volt free signal is
also activated.
Whenever an alarm condition, high or low, exists an image of a RINGING
BELL appears on the display screen. The eyebath alarm is turned on when
water flow is detected through the eyebath and the local sounder/strobe
unit will activate, if the remote alarm option is included then a volt free
signal is also activated.
The eyebath alarm is not a part of the graphic display and will not turn on any
icons until the water level drops below 572 gallons.
The local alarm sounder/beacon has a built in 30 minute timer that shuts
the alarm sound o however the strobe will continue to flash until the alarm
condition has been removed.
Filling time for the tank will depend on water pressure and flow rate, usually
taking approximately 45 minutes to fill. Heating time depends on the ambient
temperature of the filling water; a rise of 50 degrees Fahrenheit will take
approximately 9 hours.
If the graphic display screen stays blank then contact manufacturer for
replacement.
To remove the graphic display turn o MCB 3 in the enclosure above the
ceiling panel then carefully run a sharp knife around the top and both sides
of the display front to break the seal, carefully prise the display out of the
shroud opening and unplug the 32 pin plug. Using a small flat blade
screwdriver disconnect the 4 numbered wires from the terminal block.
Replacement of the new display is a reversal of the above, ensure the
numbered wires are inserted in the correct numbered terminal and re-seal
around the 3 edges, top and both sides.
TROUBLESHOOTING GUIDE

EMERGENCY TANK SHOWER TRAINING | PG. 13
WEBLINKS
SE-8000 Webpage Product Video
EYE/FACE WASH
FEATURES:
•Yellow Plastic Bowl with (2)
yellow plastic spray outlets
with flip-top dust caps
•½” NPT female brass,
chrome-plated, full flow stay-
open ball valve
•Stainless steel push handle
activator
Coming Soon Coming Soon

EMERGENCY TANK SHOWER TRAINING | PG. 14
GENERAL HELP
Q & A
QUESTIONS AND ANSWERS
Q. How often should the water in the tank be changed?
A. The time frame for changing the water in the tank will vary depending
on the quality of the water, and the surrounding environmental conditions.
Per ANSI/ISEA Z358.1 the tank shower “shall be visually checked weekly to
determine if flushing fluid needs to be changed or supplemented. Such
inspection shall be conducted in accordance with manufacturer’s
instructions”. Furthermore, Speakman suggests that the unit should be tested
at least once a week to check for optimum performance, and document data
to record results for maximum eciency. Note, after each activation
(including maintenance), the tank should be refilled to ensure it is full and
ready for use. Frequent analysis of the water quality within the unit is
recommended to ensure there is no build-up of harmful bacteria. If you are
using a water treatment supplement such as EndoSanTM, please do so in
accordance with all the manufactures recommendations and instructions.
Q. Who to contact for quote
A. Go to http://speakman.com/sales-reps/ to find a sales rep near you.
Or call 800-537-2107 for a customer service representative.
Q. What is the advantage of a tank-fed safety shower?
A. • When the need for an emergency shower exists and the company/job
site is in a remote location without access to running water.
• Older facilities where the pipes cannot produce the 20 gpm flow not meet
ANSI/ISEA Z358.1 standard for safety showers.
• Functionality is not dependent on piped water. In the event of a disaster
water supply may be shut o to prevent contamination, which would cause
plumbed fixtures to be inoperable.
Q. What standards does this meet?
A. This product meets the ANSI/ISEA Z358.1 standards.
Q. Warranty information?
A. 3 year (general mechanical) limited / 1 year (electrical equipment) limited
Q. What is the lead time?
A. 8 weeks
Q. Why is there no published price?
A. Each unit will be quoted to facilitate the needs of each individual customer.
For additional assistance or service please contact:
SPEAKMAN® Company
400 Anchor Mill Road
New Castle, DE 19720
800-537-2107
[e-mail]
www.speakman.com