Special Tomato Jogger User manual

Jogger
User’s manual

2
WARNING: AVOID SERIOUS INJURY FROM FALLING OR SLIDING OUT.
NEVER LEAVE CHILD UNATTENDED.
ALWAYS KEEP CHILD IN VIEW.
IMPORTANT: KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.
A CHILD’S SAFETY IS YOUR RESPONSIBILITY.
ALWAYS USE THE SEAT HARNESS.
ALWAYS BE SURE TO ENGAGE PARKING BRAKES WHEN IN STAND STILL
THIS VEHICLE IS SUITABLE FOR ONE CHILD.
• Front wheel must be kept in-line for exercise.
• Follow all instrucons carefully. Incorrect use will cause damage to push chair.
• This product has been designed to take the maximum weight of 110lbs (50kg).
• Children should be harnessed in at all mes and should never be le unaended.
• IMPORTANT: It is important for your child’s safety that the harness be correctly ed and adjusted. If not adjusted
correctly in accordance with the instrucons, the stability of the Jogger will be compromised.
• The harness and seat belt are not a substute for proper adult supervision.
• The child should be clear of moving parts while making adjustments.
• IMPORTANT - DANGER: It is important that care is taken to ensure that children are kept clear of the Jogger when
folding or unfolding. Pinch points and scissoring acons are unavoidable during these operaons
• Do not carry addional children, goods or accessories in or on this push chair except as permied in this manual.
They may cause the Jogger to become unstable or place unneeded stress on the Jogger that could lead to breakage.
• Overloading, incorrect folding and the use of accessories, e.g. child seats, bag hooks, rain covers, buggy boards, etc.,
other than those approved by the manufacturer may damage or break this Jogger.
• Any damage caused by the use of accessories not supplied by manufacturer will not be covered by the terms of our
warranty.
• Never leave child in the Jogger when ascending or descending stairs or escalators or when travelling on other forms
of transport.
• The Jogger should always open and fold easily. Do not force it. It may be necessary to re-read the instrucons.
• Negoate curbs and rough ground carefully. Repeated impact will cause damage to the push chair.
• Never allow children to stand on the footrest.
• Do not leave the Jogger exposed to heat, i.e., by a radiator or in direct sunlight.
• Do not place items on the top of the hood as it may cause damage to the canopy.
IMPORTANT
• READ THESE INSTRUCTIONS CAREFULLY BEFORE USE AND KEEP THEM FOR FUTURE REFERENCE.
• YOUR CHILDREN’S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS.
• APPLY BRAKE WHEN PARKING THE JOGGER.
FRAMEFRONT WHEEL REAR WHEELS
PARTS
CANOPY SEAT FABRIC

3
1. FRAME
Unpack Jogger from box and set wheels aside.
Push foot plate of Jogger away from handle by
pushing curved crossbar up and out.
Audible click will be heard when Jogger frame is
completely unfolded.
Flip Jogger to upright position.
Clip lower belting around frame to secure
seat fabric.

4
2. FRONT WHEEL
To install front wheel, lay jogger on it’s back so handle and
rear axles are touching the floor.
Engage safety lock on both sides of the fork.
Check before each use.
NOTE: Safety Lock both sides of fork.
2A. FRONT WHEEL IN-LINE LOCKING
The in-line locking mechanism is located behind the front wheel
pivot point.
Pull and rotate knob to lock and unlock. Image shows unlocked.
B
A
C
Insert the Front Wheel into the fork tips by aligning the axle
flats with the fork tip flat surfaces.
Tighten by turning the wheel lever and securing the other side.
Close the wheel lever making sure that it is flush with the
tubing. Be sure not to over tighten.
Front Brake fine adjustment knob.
A
B
C
Image now shows the wheel locked in-line.
Pull and rotate mechanism to unlock.

5
3. REAR WHEEL
To install, gently slide the rear wheel’s axle into the
frames supporting axle hole until you hear it click onto place.
To remove, simply push down the spring lock tab while
pulling out on the wheel.
3A. RAER WHEEL PARKING BREAKE
To apply the parking brake:
Press down on the foot bar..
Disengage the brake:
Pull up on the foot bar.
4. SAFETY HARNESS
Adjusting safety harness:
Unclip hooks.
Remove fleece lining (Velcro tabs shown above).
B
A
B
A

6
Adjust shoulder straps to desired height using the
loops on the seat back.
Slide the plastic guide up and down to adjust strap length.
Once fitting is complete reassemble the fleece lining.
Clip shoulder strap buckle to chest harness.
Unthread harness straps from fleece lining.
B
A
A
B
A
A
To adjust the length of the center strap, move the plastic guide
up and down.
For additional instruction refer to video guide
5. RECLINING SEAT
Simply adjust the recline strap length to desired degree of
recline.
Unlock the buckle for maximum recline.

7
6. REMOVING SEAT FABRIC
Using a phillips head screw driver unscrew
hardware from the frame.
Unsnap fasteners on both sides of jogger.
Unlock seat strap from frame, buckle is
suspended across the back of the jogger.
Unloop Velcro Strap through the D-ring, under
neath the foot well.
NOTE: REMOVE ALL RIGID PARTS BEFORE
WASHING
Joggers are shipped with Seat pre-assembled.
Assembly/Removal instructions are given
if any pre-assembly items are removed for
cleaning or replacement, refer to page 12
for additional information.
7. SHOPPING BASKET
Secure front basket flap by snapping around
the lower foot-well crossbar.
Detail of front shopping basket snaps.
Wrap rear basket straps around the frame and
loop back through the D-ring. Secure the Velcro
strap.
NOTE: The D-ring loops are at the rear of the
basket.

8
8. CANOPY
Fasten the canopy to the portion of the upper frame
that is not covered by fabric. Small holes in the crest
of the frame tubing accept the canopy. Be sure there
are NO obstructions (fabric or brake lines) between
the canopy clip and the frame. There is a small plastic
nipple on the canopy mechanism that fits into the
hole in the frame.
Hook the wire on the back side of the
canopy mechanism and then close the
lever by pressing it to the frame.
DO NOT FORCE TO CLOSE! Double check
for obstructions (fabric or break line/ be sure
nipple is inserted to frame).
9. HANDLE HEIGHT
Unlock lever on both sides of handle.
Adjust to height. Then relock.

9
10. FOLDING
Squeeze mechanism located below the handle.
(Mechanism located on Both Sides)
Fold jogger back.
Secure Jogger in folded position with recline strap.
11. ATTENDANT STRAP
Make sure safety wrist strap is secured properly around your
wrist whenever your child is in the jogger.

10
12. OPTIONAL ACCESSORIES: SEAT AND BACK LINER
Using the provided straps with the Seat & Back Liners, feed
the straps through the slots in Jogger seat & back.
Place the Back Liner Straps into the slot at the height where
you want the laterals will provide support.
The Seat Liner Straps will go through the lowest slots.
Clip the straps for both the Seat & Back Liners to each other
on the back side of the jogger and tighten until secure.
NOTE: The Jogger Chest Harness should lay over the top of
the Back Liner for correct positioning. The Jogger 3-Point
lap belt can be fed through the 3 holes of the Seat Liner for
optional positioning.

11
13. OPTIONAL ACCESSORIES: HEAD REST
Use the strap provided with the Optional Head Rest to secure
it to the Jogger.
Thread the straps through the slots on the Jogger.
Clip the straps together on the back side of the Jogger and
tighten to secure it.

LIMITED WARRANTY
Bergeron by Design warrants to the original retail purchaser of the Special Tomato® product, that if any part or component
proves defective in material or workmanship within two years of the purchase date, the defective part will be repaired or
replaced (at Bergeron by Design’s discretion) free of charge. Warranty service may be performed by an authorized service
center or (at Bergeron by Design’s discretion) the factory.
This warranty does not cover normal wear and tear, or damage caused by accident or misuse.
To exercise this limited warranty, the user should first obtain a Return Authorization Number from the dealer the Special
Tomato® product was purchased from. The product must be delivered charges pre-paid (UPS recommended) to the factory or
to an authorized service center, together with a copy of the original invoice, the Return Authorization Number and a written
description of the problem
MAINTENANCE AND REPAIR
This stroller requires regular maintenance by the user. Regularly check all rivets and connecng devices for ghtness and
security. Inspect all brakes, wheels and res and replace or repair if necessary. Check all safety devices for correct operaon,
in parcular the primary and secondary locks. These should be free to move at all mes. Never connue to use a product
that is not structurally sound.
• We recommend a service every 12 months.
• If wheels squeak, lubricate sparingly with Teon or silicone coang. Do NOT use oil or grease based products, as this
will aract dirt, which will clog the movement.
• Only manufacturer replacement parts should be used. It may be unsafe to use parts not supplied by manufacturer.
CLEANING
• Clean frame with a damp cloth and a mild detergent and dry thoroughly.
• If the stroller chassis parts have been exposed to salt water, we recommend that they be rinsed down with fresh
(tap) water as soon as possible.
• The canopy may be sponged lightly using a damp cloth and a mild detergent. The seat cover, head cushion, lateral
pads and harness pads maybe washed. Line dry thoroughly before reuse.
• Do not fold or store the product while wet and never store in a damp environment, This can cause mildew to form.
The manufacturer reserves the right to make design changes to any of their products as part of their connuous design
improvement program.
CUSTOMER SERVICE
Contact your dealer directly. Or contact the European Authorized Representative.
NOTICE
No part of this document may be photocopied, reproduced, transmitted, transcribed, stored in a retrieval system or translated
to another language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical,
manual, or otherwise without the prior written consent of Bergeron by Design.
Use only Special Tomato® accessories and parts on Special Tomato® products. Special Tomato® parts are not interchangeable
with other manufactures’ products. Replace any worn parts immediately for safety. © Bergeron By Design

13
Bergeron By Design
15 South Second Street
Dolgeville, New York 13329
T 1 315 429 8407
F 1 315 429 8862
Your stroller is guaranteed to be free from any manufacturing defects for a period of 2 years from the date of
purchase under normal use and provided it is used in compliance with the operating instructions. This warranty
extends only to the original retail purchaser and is only valid when supplied with proof of purchase. Please retain
proof of purchase with this Limited Warranty.
Should a repair be needed please contact the retailer from whom the product was purchased.
PLEASE NOTE THAT THE WARRANTY
WILL NOT BE APPLICABLE IF:
• A fault is the cause of misuse or poor maintenance.
• Repairs are carried out by a third party.
• The stroller is faulty due to general wear and tear which is the result of everyday use.
• A stroller is damaged as a result of an accident.
• The manufacturer is not satisfied that the stated warranty terms and conditions have been met.
© 2009 Bergeron By Design
The information contained herein is subject to change without notice.
Bergeron By Design shall not be liable for technical errors or omissions herein.
IMPORTANT- WARRANTY WILL BE VOID IF DEFACED OR REMOVED