Speco HTSD37X User manual

SIPSD37X & HTSD37X
37X Optical Indoor / Outdoor Speed Dome Cameras
Speco Technologies is constantly developing product improvements. We reserve the right to
modify product design and specifications without notice and without incurring any obligation.
Rev. 03082010.
200 New Hightway
Amityville, NY 11701
631-957-8700
www.specotech.com

37X Speed Dome Camera 2/50
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS.
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONAL
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
This Device compiles with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interface, and
(2) This device must accept any interference received, including interference that
may cause undesired operations.

37X Speed Dome Camera 3/50
Important Safety Guide
1. Read and follow all the Instructions
Read all the safety and operating instructions before using the product.
2. Keep this manual
Keep this manual for reference in future.
3. Attachments / Accessories
Use only the attachments or accessories specified by the manufacturer.
4. Installation
zDo not install near any heat sources such as radiators, heat registers, stoves, or other
appratus including amplifiers that product heat.
zImproperly installed product may fall, cause serious injury to a child or adult and
damage the product.
zDo not block any ventilation holes or openings. Install in accordance with the
manufacturer’s instructions.
zUse only with the cart, stand, tripod, bracket, mounting devices, or table specified by
the manufacturer.
zInstallation should be done only by qualified personnel and conform to all the
instructions by the manufacturer.
zRefer all servicing to qualified service personnel.
zUse stainless steel hardware to fasten the mount.
zTo prevent damage from water leakage when installing a mount outdoors on a roof or
wall, apply sealant properly around holes.
zThese servicing instructions are for use by qualified service personnel only. To reduce
the risk of electric shock, do not perform any servicing other that contained in the
operationg instructions unless you are qualified to do so.
zUse only replacement parts specified by the manufacturer.
5. Power source
This product should be operated only from the type of the power source indicated on the
marking label.
NOTICE

37X Speed Dome Camera 4/50
Caution
Operating
zBefore using, make sure that the power supply is properly installed.
zWhile operating, if any abnormal condition or malfunction is observed, stop using the
product immediately and then contact your local dealer.
Handling
zDo not disassemble or tamper with the parts inside the product.
zDo not drop or subject the product to shock and vibration as this can damage the
product.
zCare must be taken when you clean the clear dome cover. Especially, scratch and dust
will ruin the quality of the product.
Installation and Storage
zDo not install the product in areas of extreme temperature, which exceed the allowable
range.
zAvoid installing in places where radiation is present.
zAvoid installing in places where there are strong magnetic fields and electric signals.
zAvoid installing in places where the product would be subject to strong vibrations.
NOTICE

37X Speed Dome Camera 5/50
①Introduction
Features
6
Package Components
9
Main Part Description
10
②Installation
DIP Switch Setup
11
Installation with Wall Mount Bracket
14
Wiring and Cabling
15
③Operation
Check Points before Operation
18
Check Points for Preset and Pattern Function before
Operation
18
OSD Menu
19
Reserved Preset (Hot Keys)
19
Preset
20
Swing
20
Pattern
21
Group
22
Other Functions
22
OSD Display
24
④OSD Menu
Quick Programming Guide
25
Main Menu
25
Display Setup
26
Privacy Zone Mask Setup
27
Camera Setup
29
Motion Setup
34
Preset Setup
37
Swin
g
Setup
39
Pattern Setup
40
Group Setup
41
System Initialization
44
⑤Specifications
45
Dimensions
48
⑥Wa r ra nt y
49
TABLE OF CONTENTS

37X Speed Dome Camera 6/50
Features
Powerful Zoom Camera & Setup Options
zImage Sensor: Sony 1/4" Double density interline transfer CCD
zZoom: 37X Optical Zoom, 12X Digital Zoom
z Day & Night, Privacy Mask and WDR
z SNR (Super Noise Reduction) Function
z Various Focus Modes: Auto-Focus, Manual Focus, Semi-Auto Focus
zVarious Setup Options in OSD Menu.
Powerful Pan/Tilt Functions
zMAX. 360°/sec High Speed Pan/Tilt Motion
zWith the Vector Drive Technology, Pan/Tilt motions are accomplished along the
shortest path. As a result, the time to target view is remarkably shortened and the
video on the monitor is very natural.
zWith the Micro-Stepping Control Technology, the video looks very natural at high
zoom magnification during a jog operation on a controller since the camera can be
controlled by 0.05°/sec. Hence it is very easy to make the camera focus on desired
target views at high zoom magnification. Additionally it is easy to make the camera
focus on desired positions with zoom-proportional pan/tilt movement.
Preset, Pattern, Swing, Group, Privacy Mask and More…
zMAX. 127 Presets are programmable and each preset can have its own parameter
values independently from the other presets.
For an example, refer to the below table.
Preset No. White Balance Auto Exposure ••• Label Remarks
Preset 1 Case A Case 3 “ENTRANCE”
Preset 2 Case C Case 5 “WAREHOUSE”
•••
Preset 95 −−−−Reserved for OSD Menu
•••
Preset 128 Case K Case 9 “TERRACE”
INTRODUCTION 1

37X Speed Dome Camera 7/50
zMAX. 8 sets of Swing are programmable. This function is that the camera moves
repetitively between two preset positions at programmed speeds.
zMAX. 4 Patterns are programmable. This function is that the camera memorizes the
path (mostly curve path) by the joystick of the controller and revives the trajectory
operated by the joystick as closely as possible.
zMAX. 8 sets of Group are programmable. This function is that the camera memorizes
the combination of Presets, Pattern and/or Swings sequently and runs Presets, Pattern
and/or Swings repetitively. A Group can be combined upto 20 functions with any of
Preset/Pattern/Swing.
zMAX. 8 or 4 Privacy Masks are programmable, not to intrude on any other’s privacy.
PTZ(Pan/Tilt/Zoom) Control
zWith the RS-485 communication connection, MAX. 255 units of cameras can be
connected to a single controller.
zPelco-D or Pelco-P protocols can be selected as a control protocol in the current
firmware version.
OSD(On Screen Display) Menu
zOSD menu is provided to display the status of camera and to configure the functions
interactively.
zThe information such as Camera ID, Pan/Tilt Angle, Direction, Alarm Input and Preset
is displayed on screen.

Alarm In/Out Function(Only for the models which have I/O function)
z3 alarm sensor inputs and 1 alarm sensor outputs are available.
zAlarm sensor input is decoupled with photo-couplers to avoid external electric noise
and shock perfectly.
zBoth of N.O.(Normal Open) sensors and N.C.(Normal Close) sensors can be used and
the signal range of the sensor input is from DC 5.0V to 12.0V for various applications.
zThe camera can be set to move to a Preset position or to run functions such as Pattern,
Swing and Group when there are external sensor activations. Also “Post Alarm”
function is possible, which is supposed to activate after user-defined time period and
sequentially in succession to the action by external sensor activations.
Reserved Presets(Hot Keys)
zMost camera setup options can be set up easily and directly with the reserved presets
(Hot Keys), without entering into OSD menu. For more information, refer to “Reserved
Presets(Hot Keys)” in this manual.
INTRODUCTION 1

37X Speed Dome Camera 8/50
Network Function(Only for the SIPSD37X)
zNetwork functions including remote monitoring, bidirectional audio and others are
available through IP based network such as LAN, ADSL/VDSL, and Wireless LAN. For
more information, refer to the separated manual for IP Addressable models.

Perfect Outdoor Environment Compatibility and Easy Installation
zThe fans and heaters are built-in in the camera for cold and hot temperature
environment. Also idealistic mechanical design protects the camera from water and
dust. (IP67 when installed properly with wall mount bracket only / Only for outdoor
models)
INTRODUCTION 1

37X Speed Dome Camera 9/50
Package Component
Product & Accessories
zMain Body & Surface Mount Bracket zDefault Accessories
[Main Cable,Wrench]
zAccessories for The Models with Alarm
In/Out Function [I/O Cable]
zAccessories for The IP Addressable Models
[Crossover LAN Cable,Audio Cable,CD]
SIPSD37X Only
Wall Mount Brackets (Included)
[Screws :Machine M5×15,Hex Lag #14×50]
INTRODUCTION 1

37X Speed Dome Camera 10/50
Main Part Description
DIP Switch
Reset Switch (IP Model)
LAN Port (IP Model)
Audio Port (IP Model)
Main Connector
Sensor I/O Port (I/O Model
)
Dome Cover
Mounting Screw Hole
Drop Prevention Spring
zDomeCover Do not detach the protection vinyl from the dome cover before
finishing all the installation process to protect the dome cover from
scratches or dust.
zDIPSwitch Used to set up camera IDs and protocols.
zDrop Prevention
Spring
This part keeps the camera from dropping during installation and
maintenance. After install the Bracket, please, hang the spring to
the drop prevention hook of main body as shown in picture for
further tasks.
zMounting Screw Hole Used to assemble the main body with a bracket with screws.
zMain Connector Used for the power wire, the video cable and the RS-485
communication cable connection.
zSensorI/OPort Used for the sensor in/out connection. (The sensor I/O function
possible models only)
zLAN Port Used for the Ethernet connection. (IP addressable models only)
zAudio Port Used for the audio in/out connection. (IP addressable models
only)
zReset Switch Used to initialize all the network configurations to the factory
default. (IP addressable models only) Press the button for more
than 5 seconds to initialize the network system.
INTRODUCTION 1

37X Speed Dome Camera 11/50
DIP Switch Setup
Before installing the camera, set up the DIP switch to configure the camera ID and the
communication protocol.
Camera ID Setup
ON
O
N
12345678
zID numbers of cameras are set up with binary numbers.
See the examples shown below.
Pin 1 2 3 4 5 6 7 8
BinaryValue 1 2 4 8 16 32 64 128
ex)ID=5 on off on off off off off off
ex)ID=10 off on off on off off off off
zThe camera ID range is “1~255”. Camera ID must not be
“0”!
zThe factory default of the camera ID is “1”.
zMatch the camera ID with the Cam ID setting of your DVR
or Controller to control the camera.
zIf you are connecting a single camera to a controller,
terminate the camera. When connecting more than one
camera to a single controller, terminate the last camera on
the communication line. The last camera means the camera
farthest in cable length from the controller.
zNote that the total length of the communication cable
between a controller and the camera(s) on the same
communication line must be less than 1.2Km.
INSTALLATION 2

37X Speed Dome Camera 12/50
Communication Protocol Setup
1234
ON
ON
zSelect an appropriate Protocol with the DIP switch combination.
Switch Mode
P0
(Pin 1) P1 (Pin 2) P2 (Pin 3)
Protocol
OFF OFF OFF PELCO-D, 2400 bps
ON OFF OFF PELCO-D, 9600 bps
OFF ON OFF PELCO-P, 4800 bps
ON ON OFF PELCO-P, 9600 bps
Others Reserved
zMatch the camera protocol with the camera protocol in the setting of
your DVR or controller to control the camera.
zAdjust the DIP switch after turning off the camera. If you changed the
camera protocol by changing the DIP S/W, the change will be effective
after you reboot the camera.
zThe factory default protocol is “Pelco-D, 2400 bps”. (HTSD37X)
zThe factory default protocol is “Pelco-D, 9600 bps”. (SIPSD37X)
INSTALLATION 2

37X Speed Dome Camera 13/50
Terminal Resistor Setup
1234
ON
ON
T
he terminal resistor is used for the followin
g
cases.
zCase 1 : In case that the control cable length between a camera
and a controller is relatively very long (1:1 Connection)
If the communication cable length is very long, the electrical signal
will bound in the terminal point. This reflected signal causes
distortion of original signal. Accordingly, the camera can be out of
control. In this case, the terminal resistor of both sides i.e. the
camera and the controller must be set to ‘ON’ state.
zCase 2 : In case that multiple cameras are connected to a
controller.
Due to similar reasons with the case 1, the terminal resister of the
controller and the last camera must be set to ‘ON’ state. The last
camera means the camera farthest in cable length from the
controller. Do not turn on the terminal resistor of all the cameras on
the same communication cable.
Controller
#1 #2 #n
Terminal Resistor ON
RS-485
Terminal Resistor
OFF
Terminal Resistor
OFF
Terminal Resistor
ON
INSTALLATION 2

37X Speed Dome Camera 14/50
Installation with Wall Mount Bracket
①Make a hole whose diameter is 30~40mm
on the mounting surface to pass the
wire(s) and cable(s) through the mounting
surface. (In case of the wiring and cabling
through the mounting surface only) Then
prepare the wall mount bracket. Pull the
wire(s) and cable(s) for the system as
below. Attach the wall mount bracket to
the mounting surface. (Hex Lag #14×50)
②Hook up “Drop Prevention Spring” on
main body to prevent camera from
unexpected drop and pull the wire(s) and
cable(s) for the system as below.
③ Line up the mold lines and assemble
main body to mount adaptor and turn it.
And assemble the main both with the
camera mount adaptor with the 3 screws.
(Machine M5×15).
④ Screw the dome cover to the main body
and remove the protection vinyl from the
dome cover.
Important Notice
zBefore starting the installation,make sure that the Camera ID and Protocol are set up properly.
INSTALLATION 2

37X Speed Dome Camera 15/50
Wiring and Cabling
Port Description
zMain Cable
Port Pin Number (RJ45) Connector / Wire Color Signal
1 Video +
2,4 BNC Connector Video −
5 Red RS-485 +
3 Yellow RS-485 −
7 Orange Power +
6,8 White Power −
zI/O Cable
Port Pin Number (RJ25) Wire Color Signal
1 Blue IN COM +
2 Yellow IN 1 −
3 Green IN 2 −
4 Red IN 3 −
5 Black OUT A
6 White OUT B
RS-485
BNC
SENSOR I/O
INTERNET
INSTALLATION 2
LAN CABLE
A
UDIO
CABLE
MAIN CABLE
I/O CABLE
BROWSER
POWER
MONITO
R
CONTROLLER / DVR
MIC SPEAKER
I
R
SENSOR DOOR
SWITCH

37X Speed Dome Camera 16/50
Power Description
zCarefully check the voltage and current capacity of the rated power. The rated power is
indicated in the back of main unit.
24VAC is used on the HTSD37X (AC 17V~29V, 1.5A)
12VDC is used on the SIPSD37X (DC11V~18V, 3.0A)
zFor the DC input models, be careful with the polarity of DC power. The system should be
permanentally damaged by wrong DC input.
zIn case that the length of the power wire is very long, there may be voltage drop and the
syatem may not work properly. Make the length of the power wire as short as possible.

RS-485 Communication (HTSD37X ONLY)
zFor PTZ control, connect the cable(s) to your keyboard or DVR. To connect multiple
cameras to a single controller, RS-485 communication should be connected in parallel
as shown below. If you are connecting a single camera to a controller, terminate the
camera. When connecting more than one camera to a single controller, terminate the
last camera on the communication line. The last camera means the camera farthest in
cable length from the controller. Note that the total length of the communication cable
between a controller and the camera(s) on the same communication line must be less
than 1.2Km.
INSTALLATION 2
CONTROLLER / DVR
RS-485
+
-
#1
+
-
#2
+
-
#n
+
-

37X Speed Dome Camera 17/50
Video
zUse BNC coaxial cable only.
Alarm Input
Before connecting sensors, check driving voltages and output signal types of the sensors.
Since output signal types of the sensors are divided into Open Collector type and
Voltage Output type in general, the wiring must be done properly after considering
those types.
Signal Description
IN COM+ The electric power source to drive input circuit. Connect the (+) wire of electric
power source to drive the Sensors to this port as shown in the above circuit.
IN1 -,IN2-,IN3- Connect the outputs of sensors to each port as shown in the above
circuit.
If you want to use Alarm Input, the types of sensors must be selected in OSD menu. The
sensor types are divided into Normal Open and Normal Close. If wrong sensor types are
selected, alarms should be activated reversely to sensor inputs.
~Normal Open Output Voltage is high state when sensor is activated
~Normal Close Output Voltage is high state when sensor is not activated
Relay Output
Internal
OUT 1
AC or DC
LOAD
The maximum loads are as follows.
Power Type DC Power AC Power
Maximum Load MAX. 24VDC, 1A MAX. 125VAC, 0.5A
IN COM+ +5V~12V
IN 1-
IN 3-
+
+
-
-
+
-
Internal
Sensor 1
Sensor 3
INSTALLATION 2

37X Speed Dome Camera 18/50
Check Points before Operation
zBefore turning on the system, check if the wire(s) and cable(s) are connected properly.
zCheck if the camera ID on the controller is properly selected. The camera ID must be
identical to that of the target camera. The camera ID can be checked by reading the DIP
switch of the camera or on OSD.
zIf your controller supports multi-protocols, the protocol must be changed to match to that of
the camera.
zAdjust the DIP switch after turning off the camera. If you changed the camera protocol by
changing the DIP S/W, the change will be effective after you reboot the camera.
zSince the operation method can be different by controllers, refer to your controller manual
if the camera can not be controlled properly. The operation of this manual is based on the
standard Pelco® Controller.
Check Points for Preset and Pattern Function before Operation
zCheck fully how to operate preset function and pattern function with your controller or DVR
in advance to operate the camera functions when using a controller or a DVR.
zRefer to the following table when using standard Pelco® protocol controllers.
< Go Preset > Input [Preset Number] and press [Preset] button shortly.
< Set Preset > Input [Preset Number] and keep pressing [Preset] button for more than 2 seconds.
< Run Patter n > Input [Pattern Number] and press [Pattern] button shortly.
< Set Pattern > Input [Pattern Number] and keep pressing [Pattern] button for more than 2 seconds.
zIf your controller or DVR has no pattern button or function, use the Hot Keys with preset
numbers. For more information, refer to “Reserved Presets(Hot Keys)” in this manual.
OPERATION 3

37X Speed Dome Camera 19/50
OSD Menu
zFunction With OSD menu, the system can be properly configured for each
application.
zEntering into OSD Go Preset [95]
Reserved Presets (Hot Keys)
zDescription Some Preset numbers are reserved to change some parameters without entering
into OSD menu.
zHot Keys Go Preset [95] :Entering into OSD menu
Go Preset [131~134]
:Running Pattern Function 1 ~ 4
Go Preset [141~148]
:Running Swing Function 1 ~ 8
Go Preset [151~158]
:Running Group Function 1 ~ 8
Go Preset [161] :Turning off Relay Output
Set Preset [161] :Turning on Relay Output
Go Preset [167] :Setting Zoom Proportional Function to ON
Set Preset [167] :Setting Zoom Proportional Function to OFF
Go Preset [170] :Setting Camera BLC/WDR Mode to OFF
Go Preset [171] :Setting Camera BLC/WDR Mode to ON
Go Preset [174] :Setting Camera Focus Mode to AUTO
Go Preset [175] :Setting Camera Focus Mode to Manual
Go Preset [176] :Setting Camera Focus Mode to SEMI-AUTO
Go Preset [177] :Setting Day & Night Mode to AUTO
Go Preset [178] :Setting Day & Night Mode to NIGHT
Go Preset [179] :Setting Day & Night Mode to DAY
Go Preset [190] :Setting OSD Display Mode to AUTO (Except Privacy Mask)
Go Preset [191] :Setting OSD Display Mode to OFF (Except Privacy Mask)
Go Preset [192] :Setting OSD Display Mode to ON (Except Privacy Mask)
Go Preset [193] :Setting all Privacy Mask Display to OFF
Go Preset [194] :Setting all Privacy Mask Display to ON
OPERATION 3

37X Speed Dome Camera 20/50
Preset
zFunction MAX. 127 positions are programmable. The Preset number can be
assigned from 1 to 128 except 95. Preset 95 is reserved for entering
into OSD menu. Camera parameters such as White Balance, Auto
Exposure and others can be set up independently and each preset
can have its own parameter values independently from the other
persets. When setting up presets with a controller, Label should be
blank and "Camera Adjust" should be set to "GLOBAL" as the
default.To change the parameters, enter into OSD menu.
zSetting Presets Set Preset [1~128]
zRunning Presets Go Preset [1~128]
zDeleting Presets To delete Presets, enter into OSD menu.
Swing
zFunction This function is that the camera moves repetitively between two
preset positions at programmed speeds. When a swing function
runs, the camera moves from the preset assigned as the 1st point to
the preset assigned as the 2nd point in CW(Clockwise) direction.
Then the camera moves from the preset assigned as the 2nd point to
the preset assigned as the 1st point in CCW(Counterclockwise)
direction.
In case that the preset assigned as the 1st point and the preset
assigned as the 2nd point are same, the camera turns on its axis by
360°in CW(Clockwise) direction and then it turns back on its axis by
360°in CCW(Counterclockwise) direction. The Swing speed is
defined from 1°/sec to 180°/sec.
zSetting Swings To set Swing, enter into OSD menu.
zRunning Swings
Method 1) <Run Pattern> [Swing NO.+ 10]
Method 2) <Go Preset> [Swing NO.+ 140]
ex) Run Swing 3 :<Run Pattern> [13]
ex) Run Swing 3 :<Go Preset> [143]
zDeleting Swings To delete Swings, enter into OSD menu.
1st Preset
2nd Preset
1CW Direction
2CCW Direction
OPERATION 3