Speco HT-INTB1 User manual

Intensifier Series
Camera
HTINTB1
HTINTB2
Please read this manual thoroughly before operation and keep
it handy for further reference.

WARNING & CAUTION
The lighting flash with an arrowhead symbol, within an equilateral triangle is
Intended to alert the user to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons____________________________________
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (serving) instructions
in t h e l it e ratu r e ac c om p a n yi n g t h e ap p l i a nc e __________________
I N F O R M A T I O N - Th i s e q u i p m en t h a s b e e n t e st e d a n d f o u n d t o c o m p a n y w i t h
l i m i t s f o r a c l a s s a d i g i t a l d e v i c e P u r s u a n t t o p a r t 1 5 o f t h e F C C r u l e s .
T h e s e l i m i t s a r e d e s i g n e d t o p r o v i d e r e a s o n a b l e p r o t e c t i o n a g a i n s t h a r m f u l
I n t e r f e r e n c e W h e n t h e e q u i p m e n t s o p e r a t e d i n a c o m m e r c i a l e n v i r o n m e n t .
Thi s eq u i p m e n t gener a t e s, u se s, and Ca n Ra d i a t e radi o f req u e n c y en e r g y an d
if n ot in stal l ed a n d u sed i n acc ord ance wit h the i n str uct io n ma nu a l, ma y Ca u se
Ha rmf ul i nt e rfere nc e t o r ad i o co mm u n ic at i o n s. Ope r at i on of t hi s e q ui p me n t in a
r e s i d e n t i a l a r e a i s l i k e l y t o c a u s e h a r m f u l i n t e r f e r e n c e i n w h i c h
Ca se t h e u se r wi l l b e r e q u ire d t o c o r rec t the i n t e rfe r e nc e at h i s o w n e xpen se.
WARNING – Change or modification not expressly approved by the manufacturer could void
the user’s authority to operate the equipment__________________________________
CAUTION : To prevent electric shock and risk of fire hazards.
DO NOT use power sources other than that specified.______
DO NOT expose this appliance to rain or moisture.000
This installation should be made by a qualified service person and should conform to all local codes.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK
D O N O T R E M O V E C O V E R ( O R B A C K ) .
N O U SE R S E R V I C E A B L E P A R T S I N S I D E
R E F E R S E R V I C I N G T O Q U A L I F I E D
S E R V I C E P E R S O N N E L . _______________
CAUTION

Package Contents
Features
1
3
Contents
Precautions 4
Camera Installation 5
Focusing 6
7

Operating Your Camera
Troubleshooting
SET UP
SET UP LENS
SHUTTER SPEED CONTROL
BACK LIGHT
AUTO GAIN (AGC)
WHITE BALANCE
REDUCE NOISE
INTENSIFIER
CAMERA TITLE
DAY/NIGHT/SYNC
MOTION DETECTION
PRIVACY
REVERSE
DETAIL
DEFAULT/RETURN
11
13
15
19
20
21
23
24
25
27
29
31
32
33
9
35
2
34
Specifications / Dimensions 37
Warranty 39

PACKAGE CONTENTS
•Please make sure that the following items are included
in the package:
1 SUNSHIELD
1 REMOTE CONTROLLER
1 IR RECEIVER
4 MOUNTING SCREWS
1 M2.6 WRENCH (“L" TYPE)
1 VIDEO TEST CABLE
1 POWER CABLE ADAPTOR (for optional use)
Please leave this manual with the end-user for future
reference.
3

PRECAUTIONS
•TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE
PROPER POWER CABLE
•INSTALLATION SHOULD BE PERFORMED BY QUALIFIED
PERSONNEL
•PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR
12 VOLT DC POWER SUPPLY
•PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE
TO PREVENT FIRE OR ELECTRICAL SHOCK.
•PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA.
•PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN
CLEANING THE CAMERA.
- USE A SOFT TISSUE OR LENS CLOTH TO CLEAN THE
FRONT GLASS
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
4

CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 600 mA)
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
3. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
5
POWER SUPPLY
CONNECT
YELLOW:VIDEO OUT
CONNECT
BLACK:(-)
POWER RED(+)
POWER SUPPLY
POWER INPUT:RED
CENTER:(+)

FOCUSING
6
1. SET THE ZOOM OR FIELD OF VIEW BY USING THE
ZOOM CONTROLLER (3-9mm or 5~50mm)
SET THE FOCUS BY USING THE FOCUS CONTROLLER.
LOCK BOTH RINGS INTO POSITION USING THE SET-
SCREWS.
▣3~9 mm ▣5~50 mm
VIDEO COLOR CCD CAMERA
ZOOM CONTROLLER
FOCUS CONTROLLER
VIDEO COLOR CCD CAMERA
FOCUS CONTROLLER
ZOOM CONTROLLER

When the image is in front of strong background lighting,
your camera allows you to get the clear image.
SLC
1/3 inch density CCD and digital processor permit
high quality pictures to be captured in very low light
condition.
INTENSIFIER
Horizontal resolution of 530 TV lines is
achieved by using a SONY Double Speed CCD with
410,000 pixels, yielding pictures with a high S/N ratio..
High Resolution
Built in motion detector with adjustable areas of coverage will
flash a warning on the screen when motion is detected.
Motion Detection
Features
7

You can control a lot function on the screen.
OSD
The Intensifier camera has a DSP chip that can
remove image noise efficiently showing clean
images in low light conditions.
Dynamic Noise Reduction
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
ELECTRONIC DAY/NIGHT
The Intensifier camera will work with auto iris, manual iris and
fixed iris lenses.
MANUAL / AUTO IRIS LENS
8

Function
Operating your camera
SETUP MENU LENS option
●DC ●MANUAL
SHUTTER
●OFF ●F/L ●MANUAL
WHITE BALANCE
●ATW ●AWC MANUAL●
BACKLIGHT
●OFF ●LOW ●MIDDLE ●HIGH
AGC
●OFF ●LOW ●MIDDLE ●HIGH
DNR
●OFF ●LOW ●MIDDLE ●HIGH
SENSE UP
●AUTO ●OFF
SPECIAL
●CAMERA ID ●COLOR ●SYNC
●MOTION DET ●PRIVACY ●MIRROR
●SHARPNESS ●RESET ●RETURN
EXIT
9

10

Operating your camera
Power Connector
(DC12V in)
485(+),(-)
Baud Rate Setting
Buzzer On/Off
3. When you control by RS-485, Pelco-D protocol (Option), refer to the following.
A. DIP Switch Setting on the Camera
(Factory default : Camera Address = 01, Baud Rate = 2400bps)
B. Receiver Setting to use with IR Remote Controller
(Factory default : Baud Rate = 2400bps, Chart is same as above)
•15 Cameras can be controlled
by 1 IR Remote Controller &
1 Receiver. So you need to set
up each camera’s address by
DIP Switch on the camera
RS485 Address Set①
RS485 Baud rate Set
②
11

When you call Camera Address 01
->Push 0 Button
->Push 1 Button
->Push CAM Button
C. System Integration
D. IR Remote Controller (Remocon)
- Remocon can call and control each camera on the monitor by the
following.
Multiplexer
CCD Camera
Monitor
SET buttonUP button
DOWN button
RIGHT button
LEFT button
Receiver
IR Remote
Controller
485(+)
485(-)
12

SET UP menu is displayed on the monitor screen.
Operating your camera – SETUP
1. Press the SET button to access the SETUP mode.
Each time you press the UP or DOWN button, the arrow
indicator moves up or down.
Move the arrow indicator to the desired feature item.
2. Select the desired feature using the UP or DOWN button.
If you press RIGHT or LEFT button, it appears available status.
Press the button when gets desired feature.
3. Change the status of the selected feature using the LEFT or
RIGHT button.
4. When completed, move the arrow indicator to ‘EXIT" and press
the SET button.
Notes
You can access submenu using SET button.
For the mode with ‘---’, you may not access submenu.
13

Operating your camera – SETUP LENS
① On the SETUP menu screen, move the arrow indicator to the lens
using the UP or DOWN button.
1) Setting up the LENS
Select the lens pressing the RIGHT button.
② Select the desired feature using the LEFT or RIGHT button.
14

Operating your camera – SETUP SPEED CONTROL. ①
▶When DC LENS selected, press SET button to control the
BRIGHTNESS.
AUTO IRIS LENS (DC TYPE) is recommended than MANUAL LENS.
Some lens can make a malfunction according to the BRIGHTNES LEVEL.
Notes
15

① Press the SET button to display the setup menu and move the arrow
indicator to ‘SHUTTER’using the UP or DOWN button.
② Set ‘SHUTTER’to the desired mode using the LEFT or RIGHT button.
▶ OFF : Deactivation
▶ FLK(1/100) : Flicker mode
(When WDR is on, the image can flicker a little.)
2) Shutter status and speed control
You can control brightness of the screen by the shutter speed.
16

Operating your camera – SETUP SPEED CONTROL. ②
▶MANUAL : When setting shutter speed manually.
(Only for LENS mode)
You can select speed from ‘1/60’to ‘1/200,000’sec
17