Speco INTENSIFIER CVC6246IHR User manual

CVC6246iHR
CVC6246iHR
580 Line Color Dome Camera
Intensifier 2 Series
Wall & Ceiling Mountable
Please read this manual thoroughly before operation and keep
it handy for further reference.

WARNING & CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED
SERVICE
PERSONNEL
CAUTION
The lighting flash with an arrowhead symbol, within an equilateral triangle is
Intended to alert the user to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
ariskofelectricshocktopersons____________________________________
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operating and maintenance (serving) instructions
in
the
literature
accompanying
the
appliance
SERVICE
PERSONNEL
.
_
_____________
_
in
the
literature
accompanying
the
appliance
_
_________________
INFORMATION -This equipment has been tested and found to company with
limits for a class “A” digital device Pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful
Interference When the equipment is operated in a commercial environment.
This equipment generates, uses, and Can Radiate radio frequency energy and
if not installed and used in accordance with the instruction manual, may Cause
Harmful interference to radio communications. Operation of this equipment in a
id ti l
i
lik l
t
hfl
it f
i
hi h
DO NOT use power sources other than that specified.______
res
id
en
ti
a
l
area
i
s
lik
e
l
y
t
ocause
h
arm
f
u
l
i
n
t
er
f
erence
i
nw
hi
c
h
Casetheuserwillberequiredtocorrecttheinterferenceathisownexpense.
WARNING – Change or modification not expressly approved by the manufacturer could void
the user’s authority to operate the equipment__________________________________
CAUTION : To prevent electric shock and risk of fire hazards.
DO
NOT
expose
this
appliance
to
rain
or
moisture
000
DO
NOT
expose
this
appliance
to
rain
or
moisture
.
000
This installation should be made by a qualified service person and should conform to all local codes.
2

CONTENTS
Package Contents 4
Precautions 5
Camera Installation 6-7
OSD Menu Tree
Features 8-9
10
OSD Menu Details 11-14
Troubleshooting 15-16
Specifications 17
Dimensions 18
3
Warranty 19

PACKAGE CONTENTS
Please make sure that the following items are included
in the package:
1 CVC6246iHR Camera
2 Mounting Screws
1 Video Test Connector
Please leave this manual with the end-user for future
reference.
COMPATIBILITY
DFM Series
“A” type Box
4
Electrical Box is not included in the package but
Is compatible with the camera

PRECAUTIONS
•THIS CAMERA SHOULD BE ONLY INSTALLED BY QUALIFIED
PERSONNEL
•TO PREVENT A FIRE OR ELECTRICAL HAZARD PLEASE USE
PROPER POWER CABLE
•DO NOT CLEAN THE DOME COVER WITH AN ABRAISIVE
CLEANING MATERIAL - PLEASE USE A SOFT CLOTH OR
TISSUE TO CLEAN THE DOME COVER
•THERE ARE NO USER-SERVICEABLE PARTS INSIDE.
PLEASE DO NOT DISASSEMBLE THIS CAMERA OTHER THAN
TO MAKE INITIAL ADJUSTMENTS
•
PLEASE USE A UL APPROVED REGULATED 24 VOLT AC OR
•
PLEASE
USE
A
UL
APPROVED
REGULATED
24
VOLT
AC
OR
12 VOLT DC POWER SUPPLY
•PLEASE USE APPROPRIATE LOW VOLTAGE POWER CABLE
TO PREVENT FIRE OR ELECTRICAL SHOCK
•PLEASE INSURE THAT YOUR INSTALLATION AREA CAN
SUPPORT THE WEIGHT OF THE CAMERA
•PLEASE HANDLE THIS CAMERA CAREFULLY:
- DON’T USE A STRONG OR ABRASIVE DETERGENT WHEN
CLEANING THE CAMERA.
- DON’T EXPOSE THE CAMERA TO DIRECT SUN
5

CAMERA INSTALLATION
CONNECT POWER CABLE
1. WHEN USING 12 VOLTS DC (constant voltage 500 mA)
Power Input :RED
2. WHEN USING 24 VOLTS AC (40 Volt Amps)
DC 12V Power Supply
Center : (+)
BLACK:(
)
RED(+)
AC 24V
3. CONNECT VIDEO CABLE
-CONNECT BNC CABLE TO THE BNC JACK.
BLACK:(
-
)
Power Suppl
y
4. CONNECT Alarm output (Relay output)
-Connect (+ , COM) for Positive activation and (-. COM) for
Negative activation of External Alarm Device when Motion
Detection is ‘ON’ in the camera.
+ RED Positive Alarm Device (NO)
6
-WHITE
COM (GREY)
Alarm Output
Negative Alarm Device(NC)

CAMERA INSTALLATION
MECHANICAL
(1) DC Auto iris Lens
(2) JOY STICK
(1) DC AUTO-IRIS LENS
Adjust between TÅÆW (TELE ÅÆ WIDE) to set the
angle (focal length). Set the focus by adjusting 쏒N
(3) Video Test Terminal
NOTE: BOTH OF THE ABOVE ADJUSTMENTS GET LOCKED
INTO POSITION THROUGH THE USE OF "LOCKING HANDLES".
(2) JOY STICK
TO SET THE OSD (ON SCREEN DISPLAY) , PRESS THE JOY
STICK FOR ONE SECOND AND SET AS DESCRIBED
IN THE MANUAL
7
(3) VIDEO TEST TERMINAL

FEATURES
Horizontal resolution of 580 TV lines is achieved by using a
SONY Super-HAD CCD with 410,000 pixels, and a custom DSP
yielding pictures with a high S/N ratio..
High Resolution
1/3 inch High-inch density CCD and digital processor permit high
quality Pictures to be captured in very low light condition.
INTENSIFIER
SPECO DNR
Motion Detection with Alarm Output
The Intensifier camera has a DSP chip that can remove image
noise efficiently showing clean images in low light conditions.
SPECO
DNR
Built in motion detector with adjustable areas of coverage will
Send a signal to an external alarm device when motion is detected.
Motion
Detection
with
Alarm
Output
DAY/NIGHT
The Intensifier camera can show color pictures in all lighting
conditions, or you can have it automatically switch to a B/W
picture in low light conditions
8

FEATURES
Wh th i i i f t f t b k d li hti
SLC
All camera functions are menu driven for easy use.
OSD
Wh
en
th
e
i
mage
i
s
i
n
f
ron
t
o
f
s
t
rong
b
ac
k
groun
d
li
g
hti
ng,
your camera allows you to get a clear image.
This function reverses bright spots in the picture (such as
HLC (High Light Compensation)
headlights). This enables the entire system to do a better job of
resolving and displaying grayscale information such as a
license plate.
STABILIZATION
This function removes image jitter that is caused by vibrations in
the building and reduces the amount of hard drive space.
PRIVACY
It also has the ability to mask up to 8 areas of the picture where
Viewing is not desired. Each zone can be independently
programmed via the OSD
9

OSD MENU TREE
ADJUST LENS
INTENSIFIER
COLOR TEMP
DC IRIS
E SHUTTER AUTO GAIN INTENSIFY RETURN
COLOR
TEMP
WDR SET
SPECO DNR
SLC HLC OFF
ATW INDOOR OUTDOOR AWC SET MANUAL
DAY & NIGHT
TWEAK VIDEO
ON OFF
COLOR B/W AUTO
CAM TITLE SYNC TYPE V MOTION
PRIVACY STABILIZE LANGUAGE
PAGE 2
STILL PIX V-REVERSE
DIGI-ZOOM CLARITY
H-REVERSE
RETURN
DEFAULTS PAGE 1
EXIT
10

OSD MENU DETAILS
1 INTENSIFIER
1
.
INTENSIFIER
[OPTION : E SHUTTER / AUTO GAIN / INTENSIFY / RETURN]
-E SHUTTER
* FLK - Flicker-less mode (FLK) reduces on-screen flickering.
* ESC - Electronic Shutter Control (AUTO) adjusts brightness
level on screen.
-
AUTO GAIN
AUTO
GAIN
Adjusts value of AGC gain and increases the GAIN level to
brighten the picture. (noise / distortion may develop)
- INTENSIFY : Automatically provides a clear image under low-
light conditions. You can control the maximum low-light magnification
from 2x to 256x (increasing magnification may cause noise/distortion).
This function is deactivated when SHUTTER is set to FLK mode.
2. COLOR TEMP
[OPTIONS : ATW / INDOOR / OUTDOOR / AWC SET / MANUAL]
-ATW
Select Auto Tracking White Balance (ATW) when the color temp.
is 1800°K~10500°K.
- INDOOR
Select this when the color temp. is 4500°K~ 8500°K.
- OUTDOOR
Select this when the color temp. is 1800°K ~10500°K
- AWC SET
Set while pointing the camera towards a sheet of white paper.
Set
while
pointing
the
camera
towards
a
sheet
of
white
paper.
- Manual
It allows you to increase or decrease the red or blue factor on screen.
11

OSD MENU DETAILS
3 WDR SET
3
.
WDR
SET
[OPTION : SLC / HLC / OFF]
-SLC (Speco Light Compensation)
Provides light level control to overcome severe back light conditions.
- HLC (High Light Compensation)
High Light Compensation removes the high light and makes it possible
to view the image clearly
to
view
the
image
clearly
.
4. SPECO DNR
[OPTION : ON / OFF]
- Reduces noise/distortion on the screen.
Increasing the DNR level reduces noise but may introduce video artifacts.
DNR is deactivated if AGC is turned off.
5. DAY / NIGHT
[OPTION : COLOR / BW / AUTO]
- COLOR : Full time color mode
- BW : Full time black & white mode
- AUTO: Automatically detect color or black/white
6. TWEAK VIDEO
[OPTION : STILL PIX / V-REVERSE / H-REVERSE / DIGI-ZOOM /
CLARITY / RETURN]
- STILL PIX : Freezes the picture on the screen.
- V-REV : Flips the picture vertically on the screen.
H
REV Flips the pict re hori ontall on the screen
-
H
-
REV
:
Flips
the
pict
u
re
hori
z
ontall
y
on
the
screen
.
- D-ZOOM : Digital zoom of 1 ~10X.
- CLARITY : Sharpen the image on screen, but excessive sharpening may
cause picture noise.
- RETURN : Save the settings and return to the SETUP menu
12

OSD MENU DETAILS
7 CAM TITLE
7
.
CAM
TITLE
[OPTION : ON / OFF]
- Display a name and/or number on the monitor.
8. SYNC TYPE
[OPTION : INT / LL]
- INTERNAL : When external line lock is not required.
- LINELOCK : Adjust the vertical phase (V-P) from 000~ 359 (factory
default is 0). This function is only available with 24VAC power.
9. V MOTION
[OPTION : ON / OFF]
- When movement is detected
,
camera sends a si
g
nal to an external alarm
,g
device.
- SENSITIVITY : Select 8 different Motion Detection area. When sensitivity
number is high, it will recognize even small movement.
- AREA MODE : Activate or deactivate the selected area.
SEL POS : Select setting point from 4 different points Left
Top Left
-
SEL
POS
:
Select
setting
point
from
4
different
points
,
Left
-
Top
,
Left
Bottom, Right-Top and Right-Bottom.
- YPOS : Move setting point to vertical direction.
- XPOS : Move setting point to horizontal direction.
- FILL SET : Fills selected area with proper color.
13

OSD MENU DETAILS
10 PRIVACY
10
.
PRIVACY
[OPTION : ON / OFF]
- Mask up to 8 areas of the screen.
- AREA SEL : Select up to 8 mask areas.
- AREA mode : Activate or deactivate the selected area.
- MASK COLOR : Select area color.
- TRANSP : Adjust the transparency of selected area.
- RETURN : Save the settings and return to the SPECIAL menu.
11. STABILIZE
[OPTION : ON / OFF]
[OPTION
:
ON
/
OFF]
- Reduces picture movement due to external factors.
12. LANGUAGE
[OPTION : English / Korean / Japanese / Spanish / French]
- Choose the language that should be displayed.
13. DEFAULTS
- Restore all factory default settings.
14

If you have trouble operating your camera refer to the following
TROUBLESHOOTING
If
you
have
trouble
operating
your
camera
,
refer
to
the
following
Problem Solution
Nothing appears on
the screen.
●Check that the power cord and line connection
between the camera and monitor are correct
●Check that
y
ou have
p
ro
p
erl
y
connected VIDEO
yppy
cable to the camera VIDEO output jack.
The image on the
screen is dim.
●Is the lens stained with dirt? Clean your lens with
soft clean cloth.
●Set the monitor for the proper conditions.
●If the camera is exposed to too strong light
change the camera position.
●
Adjust the lens
’
focus
●
Adjust
the
lens
focus
.
The image on the
screen is dark.
●Adjust the contrast feature of the monitor.
●If you have an intermediate device, set the
75Ω/Hi-z properly.
The camera is not
working properly,
and
ff
●Check that you have properly connected
the camera to an appropriate power source.
the sur
f
ace o
f
the
camera is hot.
MOTION DETECTION
function is not active.
●Have you set ‘MOTION DET.’ menu to off?
●Have you set ‘MD LEVEL’ to too low?
●Have you set ‘MD AREA’ properly
15

TROUBLESHOOTING
Problem Solution
The color of the
picture is not
proper.
●Check that you have properly set the
‘ WHITE BALANCE ’ menu
The image on the
screen flickers. ●Is the camera facing to direct sunlight or fluorescent
lighting? Change the camera position.
L/L mode isn’t able
to be selected. ●Have you connected your camera to DC power
source? Connect it to AC power source.
16

SPECIFICATIONS
ITEM CVC6246iHR
Power Source 12VDC & 24VAC ( Dual Voltage )
Power Consumption 230mA (DC) / 3.8W (AC)
Image Sensor 1/3”, SONY SUPER HAD CCD, 410,000 pixels
Total Pixels 811(H) x 508(V) , 1/3” CCD
Effective Pixels 768(H) x 494(V) , 1/3” CCD
LENS TYPE DC Auto Iris Varifocal 2.8~12mm
Maximum Aperture Ratio 1 : 1.3 ~2.0
Scanning System 2 : 1 Interlaced 525 Lines / 60 Fields / 30 Frames
Synchronization Internal / Line Lock selectable
Video Output 1.0V [p-p] Composite, 75Ω
Resolution
580 TV Line
Resolution
580
TV
Line
Gain Control AGC-L, AGC-H, OFF selectable
Electric Shutter Speed 1/60 ~ 1/200,000 sec
INTENSIFIER 2 Built-in ( selectable limit ~ X256)
COLOR TEMP (White Balance) ATW / INDOOR / OUTDOOR / AWC SET / MANUAL
Min. Illumination 0.002Lux (intensifier) 0.05Lux (shutter)
S/N ( Y signal) 52dB (Weight On)
SPECO DNR ON - DYNAMIC / OFF
Motion Detection ON / OFF (8 Programmable Zone)
On Screen Display ( O.S.D ) Built - in
PRIVACY Function ON / OFF (8 Programmable Zone)
Operational Temperature -14℉~ +122℉
Operational Humidity 30% ~90% RH
17

DIMENSIONS
* SIDE VIEW
* TOP VIEW
18

WARRANTY
19

200 New Highway
Amityville, NY 11701
631-957-8700
www.specotech.com
Speco Technologies is constantly developing product improvements.
We reserve the right to modify product design and specifications without notice
and without incurring any obligation.
Rev. 100120