Speco O4BM User manual

Quick Start Guide
O4BM

Welcome
Thank you for purchasing this network camera!
This owner's manual is designed to be a reference tool for your system.
Please read this manual carefully before operating the unit and retain it for future reference.
Should you require any technical assistance, contact Speco Technologies Tech Support at
1-800-645-5516
1. Electrical safety
All installation and operation here should conform to local electrical safety codes.
Use a certified/listed 12VDC/24VAC Class 2 power supply or adequate PoE switch.
Please note: The product must be grounded to reduce the risk of electric shock.
Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment
Do not expose the unit to heavy stress, violent vibration or long-term exposure to water
and humidity during transportation, storage, and/or installation.
Do not install near sources of heat.
Only install the product in environments inside the specification operating temperature
and humidity range.
Do not install the camera near power lines, radar equipment or other electromagnetic
radiation.
Do not block any ventilation openings if any.
Use all the weatherproofing hardware requirement to minimize weather intrusion.
3. Operation and Daily Maintenance
Please shut down the device and then unplug the power cable before you begin any
maintenance work.
Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on
the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth
Important Safeguards and Warning

Warning
Statement
This camera should be installed by qualified personnel only.
All the examination and repair work should be done by qualified personnel.
Any unauthorized changes or modifications could void the warranty.
.
This guide is for reference only.
Product, manuals and specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and without incurring
any obligation.
Speco Technologies is not liable for any loss caused by improper operation.
Note:
Before installation, check the package and make sure that all components are included.
Contact your rep or Speco customer service department immediately if something is
broken or missing in the package.
dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean
the device.
Please use a professional optical cleaning method to clean the enclosure. Improper enclosure
cleaning (such as using cloth) may result in poor IR functionality and/or IR reflection.
The grounding holes of the product are recommended to be grounded to further enhance
the reliability of the camera.
Package
1
Camera Quick start guide Screw anchor × 4
Tapping screw×4

Overview
3
8 Plastic screw
anchors
Junction box
Overview
2
4 Screws
4 Screws (PA 4×25mm)
1Screw (PWM3×5mm)
(6.5×38mm)
4 Screws
(PM 4×10mm)
4 Rubber o-rings
for screws
CVBS&DC
IN cables
CD Drill template Screwdriver Terminal for 12VD
C/24VAC power
CVBS&DC
IN cable
PWR VO RS 485 ALM-I ALM-O
GND
10-pin Interface
10-pin Interface：
Network Interface
Audio InInterface
Audio Out Interface
SDcardslot
DC12VPower
Interface
AC24VPower
Interface
Zoom+
Zoom-
CVBS&DC
INInterface
Reset
12V+ GND CVBS D- D+ GND INA NO COM
DC12V Output CVBS Output RS 485 Interface Alarm Input Alarm Output
(200mA)

Reset: Press Reset button for about 10s when the camera is powering on to restore the
default settings.
Installation
3
Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera. Please install the
camera in a dry environment.
① Install a micro SD card (optional) as shown below.
TF
② Unscrew the mounting base of the camera and then remove the
junction box.
③ Drill the screw holes and the cable hole according to the drill
template.

63.6 (mm)
Ø155.4
4-Ø7.0
Ø90.0
63.6
Mounting
Base
④ Mount the junction box to the wall.
A
B
Rubber o-ring
If conduit pipe is not
used, apply
weatherproofing
sealant to prevent
water intrusion.
6.5x 38mm
4x

⑤ Connect the cables.
⑥ Coilupthesecablesandthenattachthecamera onto the junction
box.
Earth wire
connection

Rotation:360°
Tilt:90° Pan:360°
CVBS&DC
IN Cable
Zoom+
Zoom-
A
B
⑦Bracket adjustment-Before adjustment, preview the image of
the camera on a monitor and then loosen the lock screws to adjust
view angle of the camera. After that, tighten the lock screws.
⑧ Open the cover of the camera as shown below. Press T/W to
obtain an optimum image. Finally, install the cover back. Make
sure the cover is installed firmly.
Lock screws
Monitor
Web Operation and Login
4
● Operation
IP Scanner can search for the device on the local network.

The login interface is shown above. Default user name is admin and
password is 1234. After logging in, follow directions to install
applicable plugins if prompted.
③ In the device list, you can view the IP address, model number, and
MAC address of each device. Select the applicable device and double
click to open up the web viewer. You can also manually enter the IP
address in the address bar of the web browser.
① Make sure that the camera and the PC are connected to the same
local network. The camera is set to DHCP by default.
② Install IP Scanner from the CD and run it after installation.Or
download from https://www.specotech.com/ip-scanner/
5C :F2:0 7: 24: 68 :B9
O4 BM